Der PARAVAN KALI V2 Cassette lift Owner`s Manual. User manual/ PARAVAN KALI V3.3 cassette lift (Software-Update 2.0)
|
|
- Griselda Taylor
- 6 years ago
- Views:
Transcription
1 Der PARAVAN KALI V2 Cassette lift Owner`s Manual User manual/ PARAVAN KALI V3.3 cassette lift (Software-Update 2.0)
2 User manual for the PARAVAN KALI V2 cassette lift 1st Introduction The Paravan cassette lift is a lifting device, permanently mounted on the underside of a vehicle, that is designed to lift loads. The lift can be used by a person in a wheelchair to independently get into and out of the vehicle. The lift is mounted such that the the cassette opens under the rear sliding door on the passenger's side. The cassette lift consists of an electrically powered extendible platform that can be extended horizontally out of the cassette, which is securely mounted on the vehicle floor. In the extended position, the platform can be lowered or lifted hydraulically. There is an electrically powered roll stop device at the further end of the platform that can be folded out and up again. Depending on the vehicle type, a ramp is fitted on the inner end that automatically opens out to bridge the gap between the end of the platform and the internal floor of the vehicle. After loading or unloading, the platform automatically moves to the retraction position and can be automatically retracted into the cassette at the touch of a button. The cassette lift is operated using the wired remote control. A wireless remote control is available as an option. The individual functions are controlled electronically; the electronics are accommodated within the cassette lift. User manual/ PARAVAN KALI V3.3 cassette lift Page 1 of 31
3 User manual/ PARAVAN KALI V3.3 cassette lift Page 2 of 31
4 2nd Technical Data Control: electronic programmable logic controller. Operation: wired or wireless remote control Platform size: 1140 x 790 mm. Load capacity: 330 kg. Dead weight: approx. 190 kg. Lifting height: approx. 975 mm. Retracting/extending time: approx. 12 sec. (12V DC electric drive). Lowering time: approx. 9 sec. Lifting time: approx. 9 sec. (12V DC electro-hydraulic drive). Flashing lights on the side and acoustic signal during operation to warn bystanders. Electric override for all functions in the event of an emergency. Mechanical override for all functions in the event of an emergency. User manual/ PARAVAN KALI V3.3 cassette lift Page 3 of 31
5 3rd Important instructions for use and safety notices The cassette lift should only be used on a level surface. Apply the vehicle handbrake before use. The PARAVAN cassette lift is mounted on the underside of the vehicle, necessarily reducing the ground clearance. If the vehicle floor comes into contact with the ground this could result in damage to the cassette lift. Avoid driving up high kerbs. Take extra care when driving over large ramps (e.g. in car parks, the entrance to multi-storey car parks etc.). Ensure there is sufficient space between your own and other vehicles or obstructions. The PARAVAN cassette lift has been designed to transport people who use a wheelchair. Do not use it to transport other persons, animals or loads. Overloading the cassette lift could result in permanent damage. During operation of the cassette lift no other persons, animals or objects are permitted within the range of movement of the lift risk of injury! Note that the lever mechanism poses a crushing hazard. Make sure no body parts or other objects come within range of the lever mechanism during operation. Always ensure you drive onto the middle of the platform with your back to the vehicle. Always apply the wheelchair brakes. See the diagrams on the next page. Keep the operating instructions in the vehicle for future reference. All bearing surfaces are maintenance-free. However, if it should be necessary to lubricate surfaces, never use oil or grease; use Teflon spray instead. User manual/ PARAVAN KALI V3.3 cassette lift Page 4 of 31
6 C O R R E C T W R O N G W R O N G 4th Benefits of the PARAVAN cassette lift High load capacity up to 330 kg. Lifting position can be individually adjusted to the level of the vehicle interior. Easy to operate using wired remote control with intuitive symbols. Wireless remote control option available. No mechanical limit switches. Sensor-controlled positioning. Compact hydraulic unit, variable positions possible. Emergency electrical override of all functions if sensor fails. Emergency manual override of all functions if power fails. Override controls easily accessible from outside. Safety cut-out when sliding door is closed. Non-slip surface on platform, roll stop device and ramp. User manual/ PARAVAN KALI V3.3 cassette lift Page 5 of 31
7 5th Mode of operation 5th1. Getting into the vehicle using the lift Park the vehicle safely on a level surface ensuring a sufficient gap to any obstructions. Open the sliding door on the passenger's side (when the door is closed the cassette lift cannot be extended for safety reasons). Extend the platform out of the cassette. Lower the platform to the ground. Fold out the roll stop device (if a wireless remote control is used this takes place automatically). Drive the wheelchair backwards onto the platform and position it centrally (with your back to the vehicle). Raise the platform, after the roll stop device has automatically folded up. The platform automatically stops when it reaches the level of the internal floor of the vehicle and the ramp folds out, forming a level surface between the platform, ramp and internal floor of the vehicle. Drive the wheelchair into the vehicle. Put the platform away. This is simply a matter of pressing the appropriate button (if an electrical ramp is fitted, this folds up first and you need to press the button once more). The platform then automatically moves to the precise retraction position. When you press the button again, the platform automatically retracts until it is fully stowed away in the cassette. Close the sliding door. Before driving off, check to make sure that the platform is in the cassette! The vehicle is now ready to use once again. User manual/ PARAVAN KALI V3.3 cassette lift Page 6 of 31
8 5th2. Getting out of the vehicle using the lift Park the vehicle safely on a level surface ensuring a sufficient gap to any obstructions. Open the rear sliding door on the passenger's side (when the door is closed the cassette lift cannot be extended for safety reasons). Extend the platform out of the cassette. The platform is raised to the level of the internal floor of the vehicle, and if necessary the ramp folds out, forming a level surface between the platform, ramp and internal floor of the vehicle. Drive the wheelchair forwards onto the platform and position it centrally (with your back to the vehicle). Lower the platform to the ground. Fold out the roll stop device by pressing the button on the wired remote control. When using a wireless remote control, the roll stop device folds out automatically. Drive the wheelchair off the platform. Put the platform away. This is simply a matter of pressing the appropriate button (if an electrical ramp is fitted, this folds up first and you need to press the button once more). The platform then automatically moves to the precise retraction position. When you press the button again, the platform automatically retracts until it is fully stowed away in the cassette. Close the sliding door. This concludes the unloading procedure. If you use the cassette lift with the ignition on, a warning tone will sound to alert you to this. User manual/ PARAVAN KALI V3.3 cassette lift Page 7 of 31
9 6th Description of functions The wired remote control is connected to the vehicle and, through the vehicle, to the cassette lift by a flexible helix cable. All of the cassette lift functions can be controlled using the remote control, which has 7 operating buttons. There is the option to order a wireless remote control, on which buttons 1 to 3 are used. For safety reasons, the lift can only be extended when the sliding door is open. 6th1. Functions using the wired remote control 6th1.1. Extend platform When the platform is stowed away in the cassette, it can be extended electrically by pressing this button on the wired remote control. When you let go of the button the movement is instantly halted. 6th1.2. Retract platform To retract the platform into the cassette press the button shown. When you let go of the button the movement is instantly halted. This button should not be used to put the platform away; use the "Stow platform" button for this purpose. User manual/ PARAVAN KALI V3.3 cassette lift Page 8 of 31
10 6th1.3. Raise platform When you press this button the platform is raised until it reaches the level of the internal floor of the vehicle. When you let go of the button the movement is instantly halted. The platform must have been extended first! If the platform has been completely lowered to the ground, close the roll stop device first before raising the platform. If you are raising the platform without a load, it may travel slightly too far. To correct this, keep the button held down and the lift will lower slightly. 6th1.4. Lower platform Press this button to lower the platform. When you let go of the button the movement is instantly halted. The platform must have been extended first! 6th1.5. Let down roll stop device The roll stop device has a number of functions: It acts to prevent the wheelchair rolling while the platform is being raised. It also drops down below the level of the retraction position to allow the wheelchair to be driven onto the platform when the platform is at ground level. This button is used to let the roll stop device down. When you let go of the button the movement is instantly halted. For safety reasons, the roll stop device cannot be let down above the retraction position. User manual/ PARAVAN KALI V3.3 cassette lift Page 9 of 31
11 6th1.6. Draw up roll stop device When the platform is raised from the lower position the roll stop device is automatically drawn up. However, it can also be manually drawn up before raising the platform by pressing this button. When you let go of the button the movement is instantly halted. 6th1.7. Stow platform This button is used to put the platform away. This requires several steps: 1. Fold up electric ramp If an electric ramp is fitted, press this button once (press the button briefly, do not hold it down) to fold it up. If there is no electric ramp fitted, go straight to step 2! 2. Locate retraction position If the platform is raised or lowered, when you press the button again (once the ramp if fitted - has folded up), the platform either moves up or down until it reaches the retraction position for the cassette. User manual/ PARAVAN KALI V3.3 cassette lift Page 10 of 31
12 3. Retract platform When you press the button again (after the retraction position has been reached) the platform is automatically retracted into the cassette. The roll stop device is automatically retracted. You can interrupt the procedure at any time by pressing any button. User manual/ PARAVAN KALI V3.3 cassette lift Page 11 of 31
13 6th2. All functions of the wired remote control at a glance Extend platform Retract platform Raise platform Lower platform Fold up flap Fold out flap Stow platform User manual/ PARAVAN KALI V3.3 cassette lift Page 12 of 31
14 6th3. Wireless remote control Your lift can optionally be fitted with a wireless remote control. This allows you to operate all the main functions of the lift. It cannot be used to operate the electrical override. 6th3.1. Button 1 This button is used to lower the lift, irrespective of what position the platform is in. If it is retracted, the platform must first be extended before lowering. When you let go of the button the movement is instantly halted. When the platform has lowered, the roll stop device automatically opens. 6th3.2. Button 2 Use this button to raise the lift to the level of the internal floor of the vehicle, irrespective of what position the platform is in. If it is retracted, the platform must first be extended before being raised. If it is lowered, the roll stop device must first be closed before the platform is raised. When you let go of the button the movement is instantly halted. User manual/ PARAVAN KALI V3.3 cassette lift Page 13 of 31
15 6th3.3. Button 3 This button is used to retract the platform into the lift. This requires several steps: 1. Fold up electric ramp If an electric ramp is fitted, press this button once (press the button briefly, do not hold it down) to fold it up. If there is no electric ramp fitted, go straight to step 2! 2. Locate retraction position If the platform is raised or lowered, when you press the button again (once the ramp has folded up), the platform either moves up or down until it reaches the retraction position for the cassette. 3. Retract platform When you press the button again (after the retraction position has been reached) the platform is automatically retracted into the cassette. The roll stop device is automatically retracted. The procedure can be interrupted at any time by pressing button 1, button 2, button 3 or on the wired remote control. User manual/ PARAVAN KALI V3.3 cassette lift Page 14 of 31
16 7th Fuses The fuses for all functions of the cassette lift can be found on the front of the extendible carriage User manual/ PARAVAN KALI V3.3 cassette lift Page 15 of 31
17 Fuse no. Function Fuse rating Colour code 1 Control system power supply 1 A Black 2 Programming unit power supply 1 A Black 3 Control system power supply 15 A Blue 4 Control system power supply 15 A Blue 5 Flap motor + flashing lights/buzzer power supply 10 A Red 6 Retraction/extension motor power supply 20 A Yellow 7 Electric ramp motor power supply 15 A 15 A 8 Unassigned - - There are a further two fuses in the vehicle itself: 1 fuse for the entire control system power supply: 20A 1 fuse for the hydraulic unit power supply: 100 A k 8th Emergency override The PARAVAN cassette lift has a number of emergency override features. This gives you the unique ability to resolve the problem yourself, should one occur. However, you should still get the problem checked by a workshop and have the fault rectified. There are two override modes: 1. Electric override 2. Manual override User manual/ PARAVAN KALI V3.3 cassette lift Page 16 of 31
18 Caution! IF YOU CANNOT OPERATE THE CASSETTE LIFT NORMALLY USING THE WIRED REMOTE CON- TROL, MEANING THE USE OF THE MECHANICAL OVERRIDE IS NECESSARY, THIS INDICATES THERE IS A FAULT ON THE LIFT THAT REQUIRES IMMEDIATE ATTENTION. THE EMERGENCY OVERRIDE SHOULD ONLY BE USED TO RETURN THE CASSETTE LIFT TO ITS INITIAL POSITION TO ALLOW THE VEHICLE TO BE DRIVEN SAFELY. YOU SHOULD THEN IMME- DIATELY SEEK THE ASSISTANCE OF A SPECIALIST WORKSHOP OR CONTACT PARAVAN DI- RECTLY TO HAVE THE FAULT RECTIFIED. Caution! IF THE PLATFORM IS FULLY OR PARTIALLY LOCATED IN THE CASSETTE, THE "RAISE PLAT- FORM" FUNCTION SHOULD UNDER NO CIRCUMSTANCES BE SELECTED IN THIS MODE. THIS WILL RESULT IN PERMANENT DAMAGE TO THE CASSETTE LIFT. User manual/ PARAVAN KALI V3.3 cassette lift Page 17 of 31
19 8th1. Electric override To operate the electric emergency override, hold down a specific key combination on the wired remote control. Press the buttons for retracting and extending the platform (buttons A and B) at the same time and keep them held down for 5 seconds. A B C The electric emergency override is signalled optically and acoustically by a distinct rapid flashing and buzzer sequence (approx. 10Hz). After 10 seconds the electric emergency override will automatically be deactivated again if no buttons are pressed (identifiable from the normal approx. 0.8Hz flashing and buzzer sequence). To cancel emergency override immediately, press the "Stow platform" button (button C). User manual/ PARAVAN KALI V3.3 cassette lift Page 18 of 31
20 Caution! WHEN IN ELECTRIC OVERRIDE MODE, THE LOGIC IS NOT ENABLED, IN OTHER WORDS: IF YOU PRESS A BUTTON ON THE REMOTE CONTROL, THE COMMAND WILL BE DIRECTLY OUTPUT TO THE FUNCTION CONTROLS AND THE RELEVANT MOVEMENT WILL BE IMMEDIATELY PER- FORMED UNTIL THE BUTTON IS RELEASED. ALL AUTOMATIC MOVEMENTS ARE DISABLED IN THIS MODE. IN THIS CASE THE OPERATOR HOLDS PERSONAL RESPONSIBILITY FOR MOVE- MENTS OF THE LIFT AND FOR ANY RESULTANT INJURY WHEN COMMANDS ARE PERFORMED. Information: Please note that use of the electric override is logged in the control system, which will show whether and when the cassette lift has been operated in electric override mode. User manual/ PARAVAN KALI V3.3 cassette lift Page 19 of 31
21 8th2. Manual override If the vehicle electrical system fails (e.g. due to a flat battery) there is the option to operate the cassette lift manually. The following facilities are provided for this purpose. The hydraulics box with the hydraulics unit for the lift movement can be found on the right-hand side (on the left for left-hand drive vehicles) in the cassette. There are three emergency override devices on the side of this box. B A C A: lower platform manually B: raise platform manually C: manually release the drive motor for extension/retraction movement User manual/ PARAVAN KALI V3.3 cassette lift Page 20 of 31
22 8th2.1. Lowering platform manually [A] The hydraulic system incorporates an emergency relief valve to allow the platform to be lowered manually, independently of the controls. First remove the sealing plug [A]. The valve is located behind the plug. It can be actuated using the supplied Allen key (size 6). Fit Allen key Anti-clockwise: Lower Clockwise: Valve closed again The platform can also be lowered manually when loaded. It is important to actuate the valve with extreme caution to ensure the platform lowers slowly. Once the lowering function is no longer needed, shut off the valve again, remove the Allen key and replace the plug. User manual/ PARAVAN KALI V3.3 cassette lift Page 21 of 31
23 To move the platform back into the cassette, e.g. to continue driving in the event of a fault, first manually return the platform to the retraction position by manually raising or manually lowering it. You have reached this position when the lever arms are horizontal and the platform retaining plates are parallel to the lever arms. 8th2.2. Raising platform manually [B] The platform can be raised manually. First remove the sealing plug [B]. Behind this you will find a small hand pump that is connected to the rest of the hydraulic system. The pump control element can be found behind the opening. Insert the supplied hand lever into the opening in the housing and screw it into the hand pump control element. User manual/ PARAVAN KALI V3.3 cassette lift Page 22 of 31
24 Moving the hand lever horizontally from side to side operates the pump and raises the platform. You can also raise the platform when loaded; in this case, a little more effort will be needed. Once the pump is no longer needed, unscrew the hand lever again and refit the sealing plug. 8th2.3. Manually release the extension/retraction movement [C] The electric drive for the extension/retraction movement can be disengaged using the screw behind sealing plug [C]. First remove the blanking plug [C]. The screw can be actuated using the supplied Allen key (size 6). User manual/ PARAVAN KALI V3.3 cassette lift Page 23 of 31
25 Fit Allen key Turn clockwise until resistance is felt: Disengaged Turn anti-clockwise until resistance is felt: Engaged Do not apply more than slight pressure to the screw once it reaches the mechanical stop in both directions! Once the motor has been disengaged using the screw, it is easy to slide the platform into and out of the cassette with little effort. Caution! ONCE THE PLATFORM HAS BEEN MOVED TO THE REQUIRED POSITION, YOU MUST RESET THE SCREW TO ITS ORIGINAL POSITION BY TURNING IT FULLY ANTI-CLOCKWISE, AND THEN REFIT THE SEALING PLUG. AFTER USING THE User manual/ PARAVAN KALI V3.3 cassette lift Page 24 of 31
26 EMERGENCY OVERRIDE, THE PLATFORM MUST BE MECHANICALLY SECURED USING THE LOCKING MECHANISM. (SEE CHAPTER 8.2.5) IF YOU FAIL TO SECURE THE PLATFORM IT COULD SLIDE OUT OF THE CAS- SETTE CAUSING SEVERE DAMAGE! ONCE THE FAULT HAS BEEN REPAIRED, IT IS ESSENTIAL TO CHECK THAT THE PLATFORM CAN ONLY BE ACTUATED ELECTRICALLY! IT MUST NOT BE POSSIBLE TO MOVE THE PLATFORM BY HAND, EVEN WHEN A LARGE FORCE IS APPLIED! 8th2.4. Manual operation of the roll stop device User manual/ PARAVAN KALI V3.3 cassette lift Page 25 of 31
27 The roll stop device drive motor can be mechanically disconnected from the flap. For this purpose, remove the spring clip and the small locking pin from the drive/flap interface. (Shown here in retracted position). The flap will now move freely at the front end of the platform. If the platform needs to be retracted into the cassette in this condition, the drive can be screwed into the drive housing by turning the piston rod to the right, if it is extended when dismantled. The locking pin can then be used to connect the drive to the flap again so as to close the flap when the platform is in the cassette. It is essential to re-engage the mechanical release for the retraction/extension motor before driving off. The flap security device must be put in place to provide additional safety. User manual/ PARAVAN KALI V3.3 cassette lift Page 26 of 31
28 8th2.5. Flap security device If you have used the manual release for the extension/retraction movement, it is essential to use the flap security device until the lift has been repaired! The mechanical emergency flap security device can be fitted on the left side of the cassette. It consists of a red metal angle and a knurled screw. Fit the angle using the screw as shown. User manual/ PARAVAN KALI V3.3 cassette lift Page 27 of 31
29 Once this step has been correctly carried out, it will not be possible to pull the platform out of the cassette and you can continue with your journey. User manual/ PARAVAN KALI V3.3 cassette lift Page 28 of 31
30 User manual/ PARAVAN KALI V3.3 cassette lift Page 29 of 31
31 Contents TOC User manual/ PARAVAN KALI V3.3 cassette lift Page 30 of 31
32 PARAVAN GmbH PARAVAN Str D Pfronstetten-Aichelau Germany Tel.: +49 (0) Fax: +49 (0) Web: User manual/ PARAVAN KALI V3.3 cassette lift Page 31 of 31
PARAVAN transfer console
PARAVAN transfer console User s manual User s Manual/transfer console/version 1.10 PARAVAN Transfer Console User Manual For simple, convenient and comfortable transfer in the vehicle 1. Introduction You
More informationCAUTION -TABLE OF CONTENTS- II. OPERATING INSTRUCTIONS
-PRINT- -TABLE OF CONTENTS- II. OPERATING INSTRUCTIONS his chapter contains safety precautions, daily safety check instructions, control and indicator descriptions, and operating instructions that apply
More informationS-SERIES PUBLIC USE OPERATING INSTRUCTIONS
-PRINT- II. T S-SERIES PUBLIC USE OPERATING INSTRUCTIONS -TABLE OF CONTENTS- his chapter contains safety precautions, daily safety check instructions, control and indicator descriptions and operating instructions
More informationOwner s Manual. (Keep in glove compartment for quick reference) Rollx Vans Power Door Vans v1.3
Owner s Manual (Keep in glove compartment for quick reference) Rollx Vans Power Door Vans v1.3 Table Of Contents Warranty Procedures.................. 4 Warranty Coverage.................... 5 Preventative
More informationK-SERIES PUBLIC USE LIFT OPERATING INSTRUCTIONS
-PRINT- II. T K-SERIES PUBLIC USE LIFT OPERATING INSTRUCTIONS -TABLE OF CONTENTS- his chapter contains safety precautions, daily safety check instructions, control and indicator descriptions, and operating
More informationThe electro-mechanical power steering with dual pinion
Service Training Self-study programme 317 The electro-mechanical power steering with dual pinion Design and function The electro-mechanical power steering has many advantages over the hydraulic steering
More informationThis chapter contains safety precautions, daily safety check instructions, control and indicator
III. OPERATING INSTRUCTIONS This chapter contains safety precautions, daily safety check instructions, control and indicator descriptions and operating instructions for the RICON S-Series Export Use Wheelchair
More informationCommander 15i Container and Pallet Loader. Property of American Airlines
Commander 15i Container and Pallet Loader Section 2. Operation BEFORE ATTEMPTING TO OPERATE OR MAINTAIN THE VEHICLE, COMPLETELY READ AND UNDERSTAND THE OPERATION AND MAINTENANCE MANUAL, INCLUDING ALL DANGER,,
More informationThe electromechanical parking brake
Service Training Self-study programme 346 The electromechanical parking brake Design and function To make absolutely sure that the vehicle could not roll away when parked up, the driver had to pull up
More informationModel S888NR & Model S889NR USER MANUAL. Please ensure this manual is read and understood before using the scooter.
Model S888NR & Model S889NR USER MANUAL Please ensure this manual is read and understood before using the scooter. CONTENTS Introduction 3 Feature Guide 3 Safety Advice 4 Adjustments 4 Tiller angle Seat
More informationTurny Evo. Autoadapt. Seat lift. Installation manual
Turny Evo Autoadapt Seat lift EN Installation manual Getting seated Turny Evo Thank you for choosing a Turny Evo from Autoadapt! The manual that follows is an integral, important part of the product,
More informationInformation I Manuals I service. AIR premium x2. Operating Instructions _a I 03/2012
GB Information I Manuals I service AIR premium x2 Operating Instructions 1 568 419_a I 03/2012 1 6 7 2 3 4 8 5 Dear customer, Your vehicle is equipped with the AL KO AIR Premium X2 electronically controlled
More informationService Manual Gulf Stream Electronic Full Wall Slide Systems
Service Manual Gulf Stream Electronic Full Wall Slide Systems CONTENTS Page Before you operate the slide system 2 Operating Instructions 3 Preventive maintenance 3 Manually overriding your slide system
More informationCo-pilot Owner s manual
Attendant controller Co-pilot Owner s manual US How to contact Permobil Permobil Inc. USA 6961 Eastgate Blvd. Lebanon, TN 37090 USA Phone: 800-736-0925 Fax: 800-231-3256 Email: info@permobilus.com Head
More informationModel PRO-9675FT4 Owner's Manual
Model PRO-9675FT4 Owner's Manual 4 Button Remote Start Security System With Plug-In Shock Sensor & Starter Disable FEATURES : w 2 Four Button Programmable RF Transmitters w Four Channel Code Learning Receiver
More information42 Series Step. Owner's Manual #842A. Equipped with a Permanent Magnet Motor. Table of Contents
Owner's Manual #842A 10/05 Kwikee #1422258, Rev. 0A ED 42 Series Step Equipped with a Permanent Magnet Motor D IS C O N TI N U For steps with Control Unit 909510000 and steps without Control Units Table
More informationS-SERIES ADA TRANSIT USE OPERATING INSTRUCTIONS
-PRINT- II. T S-SERIES ADA TRANSIT USE OPERATING INSTRUCTIONS -TABLE OF CONTENTS- his chapter contains safety precautions, daily safety check instructions, control and indicator descriptions, and operating
More informationEZ LITE CRUISER. Service & Maintenance Manual
EZ LITE CRUISER Service & Maintenance Manual Table Of Contents Introduction to the EZ Lite Cruiser 3 Identification of Components 4 Controller System Component Diagram 6 Controller System I/O Ports Detail
More informationshortform operating instructions
B 0800 52 15 95 www.facelift.co.uk ascendant 17m shortform operating instructions SAFETY TIPS ALWAYS Inspect your machine before use. Check all operations including ground controls. Check ground conditions.
More informationGPS Steering System Installation Manual
GPS Steering System Installation Manual Supported Vehicles Challenger Massey Ferguson AGCO MT-645C, MT-645D MF-8650 DT-205B MT-655C, MT-655D MF-8660 DT-225B MT-665C, MT-665D MF-8670 DT-250B MT-675C, MT-675D
More informationInstruction manual. Liftkar HD Uni Liftkar HD Fold Liftkar HD Dolly Liftkar HD Fold Dolly. Issued: 10/2010 subject to updates.
Instruction manual Liftkar HD Uni Liftkar HD Fold Liftkar HD Dolly Liftkar HD Fold Dolly Issued: 10/2010 subject to updates. en Contents 1 INTRODUCTION AND KEY FEATURES... 3 1.1. General safety guidelines...
More informationSI AT A22. English. Printed: Doc-Nr: PUB / / 000 / 01
SI AT A22 English 1 Information about the documentation 1.1 About this documentation Read this documentation before initial operation or use. This is a prerequisite for safe, trouble-free handling and
More informationOperating instructions ErgoPack 600 E
Operating instructions ErgoPack 600 E Operation of the device is only permitted if the operating instructions have been carefully read and understood before use! Declaration of conformity EU declaration
More informationService Bulletin No. 2905
MODEL TYPE SECTION/GROUP DATE E4500 / J4500 Series Coaches Service Information 22-Wheelchair Lift May 4, 2005 SUBJECT R ICON W HE E L CHAIR L IF T OPE R AT ION CONDITIONS Service Information Only Description:
More informationREMOTE CARAVAN MOVER Installation guide and user information. e-go /10/01/rev 3
REMOTE CARAVAN MOVER Installation guide and user information Contents 1 1 Introduction 3 Parts List 4 Safety Guidelines 4 Technical Specifications 5 Fitting Guidelines (chassis adapters etc.) 6 Fitting
More informationSECTION B1: MACHINE COMPONENTS
SECTION B1: MACHINE COMPONENTS The machine portion of the Injected Metal Assembly system provides the means for: holding, heating and injecting the alloy; distributing and controlling electrical, pneumatic,
More informationEAGLETRON II REMOTE CONTROL OPERATOR and MAINTENANCE. Remote Control Procedure
EAGLETRON II REMOTE CONTROL OPERATOR and MAINTENANCE Remote Control Procedure WARNING! DO NOT OPERATE REMOTE CONTROL UNLESS YOU HAVE A CLEAR VIEW OF THE REAR OF THE TRAILER. WARNING! THE OPERATOR IS REQUIRED
More informationEdition Manual Chapter Page Workshop Manual, Stiga Park 5 Belts 11
2008-05-19 Workshop Manual, Stiga Park 5 Belts 11 Pro 20 1. Dismantle the belts A and B as described above. 2. Block up the rear frame and remove the right rear wheel. Clean carefully the insex hole in
More informationThe parking brake is an electrically actuated system that operates drum brakes integrated into the rear brake discs. The
Page 1 of 15 Published: Oct 22, 2004 Parking Brake COMPONENT LOCATIONS Item Part Number Description 1 Clutch pedal position sensor (manual transmission models only) 2 Parking brake indicators (all except
More informationSI AT A22. English. Printed: Doc-Nr: PUB / / 000 / 03
SI AT A22 English 1 Information about the documentation 1.1 About this documentation Read this documentation before initial operation or use. This is a prerequisite for safe, trouble-free handling and
More informationEmbraer Systems Summary [Landing Gear & Brakes]
GENERAL DESCRIPTION The airplane has two main landing gears and a single nose gear. Each main gear is a conventional two-wheeled landing gear. The nose gear is a conventional steerable two-wheeled unit.
More informationModel Number: CM-046. QUATTRO Handset Installation guide and user information. Ref: CM-046 UK-Rev.C.
Model Number: CM-046 QUATTRO Handset Installation guide and user information UK Ref: CM-046 UK-Rev.C. Table of Contents Package Contents (Parts List) Page 2 Introduction Page 4 Installation Safety Guidelines
More informationSUSPENSION MODULE by
SUSPENSION MODULE by Dear Customer, thank you for choosing Land Rover Passion and for purchasing the suspension module Easy Lift. This product has been designed and manufactured respecting the highest
More informationProperty of American Airlines
Section 2: Operation 1. GENERAL INFORMATION Safety First! is the motto at Tesco; therefore, the first part of the Operation section begins with safety features and procedures. Operation of the Tesco CL80-20
More informationConvertible Top ! WARNING: OPENING THE CONVERTIBLE TOP
Convertible Top OPENING THE CONVERTIBLE TOP JAG062L The power-operated convertible top and rear quarter windows, see page 85, are controlled by the switch located on the overhead console. The top latches
More informationRegular maintenance of the RICON S-Series Transit Use Wheelchair Lift will help optimize its
IV. MAINTENANCE AND REPAIR Regular maintenance of the RICON S-Series Transit Use Wheelchair Lift will help optimize its performance and reduce the need for repairs. This chapter contains cleaning and lubrication
More informationCONTROLLER DIAGNOSTIC GUIDE
Proprietary tice: This document contains proprietary information which not to be reproduced, transferred, to other documents, disclosed to others, used for manufacturing or any other purpose without the
More informationType Operating Instructions. Angle Seat Motor Valve Compact. BM24C, BM24C/I BM24C/IOS, BM230C/IOS with and without spring return
Operating Instructions Angle Seat Motor Valve Compact Type 70 Valid For Actuators: BM4, BM5, BM30, BM4C, BM4C/I BM4C/IOS, BM30C/IOS with and without spring return Version: 08/004 W70e.doc Art.-Nr: 70 Bunsenstrasse
More informationPlatform Length Length With Towers Platform Width Width with Towers Working Height Fixed Height Models
Rack Platforms OVERVIEW Grabber s Winner Series of rack platforms are a snap to set up and unrivaled in their ease of operation. With true 360 pulling access, Winner Series racks offer unsurpassed efficiency
More informationBreezair TBA 550 Installation Manual
Breezair TBA 550 Installation Manual Table of Contents ITEM Safety Instructions Specifications Exploded View of the Air Cooler Components of the Air Cooler Dismantling the Air Cooler Installing the Transition
More informationOperating manual and installation instructions ENGLISH. Electronic engine remote control. Copyright 2001 Vetus den Ouden n.v.
Operating manual and installation instructions ENGLISH Electronic engine remote control Copyright 00 Vetus den Ouden n.v. Schiedam Holland Contents Introduction... General conditions of use... Operating....
More informationComfort Recliner by American Leather
Comfort Recliner by American Leather YOUR GUIDE TO OPERATING THE ULTIMATE POWER RECLINER V 07.01.16 Congratulations on your purchase of the power Comfort Recliner by American Leather. Following are helpful
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY A20 5TH WHEEL HITCH TABLE OF CONTENTS Page# Description 1 Warnings & Precautions 2 - Assembly & Installation
More informationInstallation & Service Manual
Installation & Service Manual for M² Sync Slideout Control Box #1510000122 CONTENTS Introduction Installation Installation Problems Program Mode Operation Mode Preventative Maintenance Fault Diagnostics
More informationOwner s Manual (Keep in glove compartment for quick reference) Honda Version 1.8
Owner s Manual (Keep in glove compartment for quick reference) 2005-2010 Honda Version 1.8 Table of Contents Introduction...1 Warranty Procedures...2 Preventative Maintenance...4 Basic Operation...6 Electronic
More informationLesson 5: Directional Control Valves
: Directional Control Valves Basic Hydraulic Systems Hydraulic Fluids Hydraulic Tank Hydraulic Pumps and Motors Pressure Control Valves Directional Control Valves Flow Control Valves Cylinders : Directional
More informationThe Stannah Stairiser SX User Manual
9 NOTES The Stannah Stairiser SX User Manual Make sure you understand the contents of this booklet. Keep it handy for reference. Your Stairlift Number is: Please quote this number on any correspondence
More informationChapter 5 Part B: Ignition system - transistorised type
5B 1 Chapter 5 Part B: Ignition system - transistorised type Contents Coil - testing........................................... 9 Distributor - overhaul..................................... 7 Distributor
More informationSECTION B: SYSTEM OPERATING COMPONENTS
SECTION B: SYSTEM OPERATING COMPONENTS A brief description of the machine, Cable Processor Module and tooling will provide a better understanding of the various functions of the IMA system. SECTION B1:
More informationComfort Theatre by American Leather
Comfort Theatre by American Leather YOUR GUIDE TO OPERATING THE ULTIMATE POWER THEATRE SEATING V 07.01.16 Congratulations on your purchase of the power Comfort Theatre by American Leather. Following are
More informationSupport legs. Installation and operating instructions
Support legs Installation and operating instructions Table of contents 1 Explanation of symbols... 3 2 Assembly... 4 3 Operation... 5 4 Servicing and testing... 8 2 MUB 013 001 M01 (REV--) 11/2016 Support
More informationAQUATEC R / AQUATEC F / AQUATEC XL. Bathlift Operating instructions
AQUATEC R / AQUATEC F / AQUATEC XL Bathlift Operating instructions 1 2 3 4 5 6 7 8 9 10 11 Contents 1 General instructions................. 3 1.1 Introduction......................... 3 1.2 Proper use.........................
More informationInstallation and Service Manual
RAVE Star Lift Installation and Service Manual WARNING! STRICT ADHERENCE TO THESE INSTALLATION INSTRUCTIONS is required and will promote the safety of those installing this product, as well as those who
More informationDrive Unit e-drive1. Installation instructions 04/2014. English translation of the original German installation instructions
Drive Unit e-drive1 Installation instructions 04/2014 English translation of the original German installation instructions Contents Foreword... 3 Availability... 3 Structural features in the text... 3
More informationII. W-SERIES WHEELCHAIR LIFT OPERATING INSTRUCTIONS T
II. W-SERIES WHEELCHAIR LIFT OPERATING INSTRUCTIONS T his chapter contains safety precautions, daily safety check instructions, control and indicator descriptions and operating instructions for the RICON
More informationOPERATIONS MANUAL SECTION 6-2
SECTION 6-2 Index Page Pilot's Seats... 6-2-2 Pilot's Seats Adjustment... 6-2-4 Pedals Adjustment... 6-2-5 Direct Vision Windows... 6-2-6 Observer's Seat... 6-2-7 Attendant's Furnishings Typical (Version
More informationRemoving and installing dash panel insert
Removing and installing dash panel insert Caution To disconnect and connect the battery, the procedure described in the workshop manual should be strictly adhered to Chapter. Note Pull off multi-pin connector
More informationInstallation and Service Manual M² Sync Room Slideout System without Room Lock Connectors on Control Box
Installation & Service Manual M² Sync Room Slideout System w/o Room Locks: for Slideout Control Box# 1510000143 and 1510000198 Figure 1 01/13 Power Gear #3010002088 Rev. 0C Installation and Service Manual
More informationCAUTION CAUTION MAINTENANCE AND REPAIR A. LUBRICATION
III. R MAINTENANCE AND REPAIR egular maintenance of the Ricon KlearVue Series platform wheelchair lift is required to help optimize its performance and reduce the need for repairs. This chapter contains
More informationDEEP SEA ELECTRONICS PLC
DEEP SEA ELECTRONICS PLC 703 AUTOMATIC START MODULE OPERATING INSTRUCTIONS Author:- John Ruddock 703 Operating Instructions Issue Beta1 25/08/2003 2:45 PM JR - 1 - >
More informationOwner s Manual and Warranty Information
SIERRA Incline Platform Lift Owner s Manual and Warranty Information IMPORTANT! YOU MUST READ AND UNDERSTAND THIS ENTIRE MANUAL BEFORE ATTEMPTING TO OPERATE THIS LIFT. IF THERE IS ANYTHING IN THIS MANUAL
More informationSvendborg Conveyor Brake Maintenance
CLIENT LOGO OPF MAINTENANCE WORK INSTRUCTION CLIENT DOC NUMBER Scope PREPARATION AND INFORMATION The Svendborg Brake is designed to transfer a braking torque from the calliper to a brake disc in order
More informationEngine-specific faults and their remedy are given in the operating manual of the engine manufacturer. Fault Possible cause Rectification
Simple troubleshooting D2-1.1 Engine Engine-specific faults and their remedy are given in the operating manual of the engine manufacturer. Fault Possible cause Rectification The superstructure cannot be
More informationINSTRUCTION MANUAL 16K - Fifth Wheel Hitch
You can take it with you. INSTRUCTION MANUAL 16K - Fifth Wheel Hitch Product No. 30047 DEALER/INSTALLER: END USER: (1) Provide this Manual to end user. (2) Physically demonstrate hitching and unhitching
More information16 37 TM INTEGRATED RADIO CONTROL INSTRUCTION MANUAL
16-37 TM IRC Instruction Manual (99903542) 16 37 TM INTEGRATED RADIO CONTROL INSTRUCTION MANUAL 01.01 2007 IOWA MOLD TOOLING CO., INC. GARNER, IA 50438 1. Introduction... 2 2. The Components of the IRC-System...
More informationProperty of American Airlines
Date Maintenance Check list The inspection and preventive maintenance schedule of the Power Stow Rollertrack is as follows: Daily (10 hrs), Weekly (50 hrs.), every 6 months ( hrs.), yearly (1 hrs.) and
More informationROM Series. Keeping the World Flowing. Installation Manual. Valve Actuators
ROM Series Installation Manual Valve Actuators Keeping the World Flowing Contents Section Page Health and safety 3 Storage 4 Mounting the actuator 4 Setting the actuator stop bolts 5 Cable connections
More informationLanding Gear & Brakes
EMBRAER 135/145 Landing Gear & Brakes GENERAL The EMB-145 landing gear incorporates braking and steering capabilities. The extension/retraction, steering and braking functions are hydraulically assisted,
More informationModel PRO-9775T Owner's Manual 4 Button Remote Start Security System With Plug-In Shock Sensor & Starter Disable
Model PRO-9775T Owner's Manual 4 Button Remote Start Security System With Plug-In Shock Sensor & Starter Disable FEATURES:! 2 Four Button Programmable RF Transmitters! Four Channel Code Learning Receiver
More informationOn the following pages you will find the user manual for the Strider MD 3 and MD 4 3- wheel and 4-wheel version mobility scooter.
On the following pages you will find the user manual for the Strider MD 3 and MD 4 3- wheel and 4-wheel version mobility scooter. We have a range of Drive Medical scooters available Drive now owns the
More informationWWWAUTO-ROLLER.CO.ZA INSTALLATION MANUAL AUTO- ROLLER
WWWAUTO-ROLLER.CO.ZA INSTALLATION MANUAL AUTO- ROLLER Notice. Please read these instructions carefully before installing the Rolling Door motor 1. The motor must be installed and operated by a professional.
More informationModel AS-9234E. Owners Guides
Model AS-9234E Owners Guides This unit is capable of 3 installation methods. Select the guide for your customer that matches the installation in their particular vehicle. PATENTED: www.voxxintlcorp.com/company/patents
More informationTroubleshooting Guide
Troubleshooting Guide diesel - gasoline - LPG P/N 0172021 June 1999 P.O. Box 1160 St. Joseph, MO 64502-1160 1-800-255-0317 Fax: 816-360-9379 www.snorkelusa.com GENERAL INFORMATION This manual contains
More informationKwikee # Series Step OWNER'S MANUAL ( )
Kwikee #842 42 Series Step OWNER'S MANUAL (1422258) TABLE OF CONTENTS Safety Information 2 Product Information 3 Step with Control Unit 3 Operation 3 General Service 4 Prior To Operation 4 Adjusting Cam
More informationModels CHASSIS LUBE ELECTRIC GREASE PUMP Series "C" - 13C MAY FORM Page. Section - Q3
Models 94422 CHASSIS LUBE ELECTRIC GREASE PUMP Series "C" MAY - 2004 FORM 403467 Section - Q3 Page - 13C 9.00" (229 mm) 13.75" (350 mm) 0.35" (9mm) Mounting Holes 4.76" (121 mm) 9.84" (250 mm) Do not use
More informationOPERATION INSTRUCTIONS
OPERATION INSTRUCTIONS FOR SPACESAVER POWER ASSIST CONTROLS SYSTEM PREPARED FOR: SPACESAVER ORDER NUMBER: P A G E ONE TOUCH - MANUAL RESET... 2 A/B ELECTRO - MECHANICAL SWEEP... 3 DUAL ELECTRO - MECHANICAL
More informationModel CHASSIS LUBE ELECTRIC GREASE PUMP Series "C"
Model 94222 CHASSIS LUBE ELECTRIC GREASE PUMP Series "C" Indicates change MAY - 2004 FORM 403466 Section - Q3 Page - 12B 7.75" (197 mm) 12.6" (321 mm) 0.35" (9 mm) Mounting Holes 4.85" (123 mm) 8.85" (225
More informationROM Series. Established Leaders in Flow Control. Installation Manual. Valve Actuators
ROM Series Installation Manual Valve Actuators Established Leaders in Flow Control Contents Section Page Health and Safety 3 Storage 4 Mounting the actuator 4 Setting the actuator stop bolts 5 Cable connections
More informationUser Manual Rittal PMC UPS 6kVA
User Manual Rittal PMC UPS 6kVA Germany Rittal GmbH & Co. KG Auf dem Stützelberg D-35745 Herborn Tel.: ++49-27 72-5 05-0 Fax: ++49-27 72-5 05-23 19 Internet: www.rittal.de 26 Contents 1. Introduction...
More informationDO NOT INSTALL, OPERATE, OR MAINTAIN AN ATI PRODUCT UNLESS TRAINED AND QUALIFIED IN PRODUCT AND ACCESSORY INSTALLATION, OPERATION AND MAINTENANCE.
IOM Supplement IOMS003 ATI HO1/HO2 HYDRAULIC OVERRIDE Scope of Supplement This supplement is intended to assist those who are involved with the installation, operation and maintenance of ATI Linear Actuators
More informationEminox Electronic Service Indicator
ESI Installation and Instruction Manual Eminox Electronic Service Indicator I n s t a l l a t i o n a n d I n s t r u c t i o n M a n u a l LITM004 ESI Installation and Instruction Manual Section Title
More informationV8 Vantage Sportshift Driving Guide
LG/GE/10/03/2011 The V8 Vantage incorporates a 6-speed Sportshift automated manual transmission. There are two driving modes for V8 Vantage Sportshift. The first is Paddle Shift Mode This is the mode where
More informationModels CHASSIS LUBE ELECTRIC GREASE PUMP Series "C" - Q3. MAY FORM Section
Models 94822 CHASSIS LUBE ELECTRIC GREASE PUMP Series "C" - Q3 MAY - 2004 FORM 403468 Section Page - 14B 13.00" (330 mm) 17.72" (450 mm).35" (9 mm) Mounting Holes 4.72" (120 mm) 9.84" (250 mm) Figure 1
More information1. Disclaimer Warnings Introduction Display and Commands... 5
1. Disclaimer... 1 2. Warnings... 2 2.1. Welding... 2 3. Introduction... 3 4. Display and Commands... 5 4.1. Status Display on LCD... 5 4.1.1. Control Mode... 6 4.1.2. Bowl Mode... 6 4.1.3. Engine Mode...
More informationWARNING TABLE 3-1: DAILY SAFETY CHECK
III. T PSL-10 MAINTENANCE his chapter contains maintenance information for the Ricon PSL-10. The information consists of a maintenance schedule, component descriptions, electrical diagrams, fuse locations,
More informationModel AX-510 Owner s Manual
Model AX-510 Owner s Manual 4 Button Remote Security System with Dual Stage Shock Sensor IMPORTANT! In order to provide the highest possible level of security to your vehicle, this system is equipped with
More informationOPERATING INSTRUCTIONS
II. T OPERATING INSTRUCTIONS his chapter contains safety precautions, a daily safety check, a description of lift functions, control and indicator descriptions, plus operating instructions for both the
More information3 Ton Trolley Jack. Please read and fully understand the instructions in this manual before operation. Keep this manual safe for future reference.
Please dispose of packaging for the product in a responsible manner. It is suitable for recycling. Help to protect the environment, take the packaging to the local amenity tip and place into the appropriate
More information2006 MINI Cooper SUSPENSION Wheels & Tires - Repair Instructions - Cooper (1.6L) R50/W10 & Cooper S
WHEELS 2002-05 SUSPENSION Wheels & Tires - Repair Instructions - Cooper (1.6L) R50/W10 & Cooper S 36 10 300 REMOVING OR INSTALLING FRONT OR REAR WHEEL NOTE: For Special Tool identification, see WHEEL AND
More informationM-Series 415 & in 1 Elevator Light Curtain. Installation Manual
M-Series 415 & 405 2 in 1 Elevator Light Curtain Installation Manual Table of contents PRINCIPLE 1 INSTALLATION 2 MOUNTING THE POWER SUPPLY MS721 6 POWER SUPPLY MS721 AND EARTH CONNECTION 8 FUNCTIONAL
More informationInstallation Instructions for Model CityFix
INTERLIFT Interlift, Inc. 15939 Piuma Ave. Cerritos, CA 90703 Tel: 888-774-5844 Fax: 562-924-8318 Installation Instructions for Model CityFix www.interlift.net 1. LIFT LOCATION The installation surface
More informationSERIES G3DB/AG3DB ELEVATOR
TM INSTRUCTIONS AND PARTS LIST SERIES G3DB/AG3DB ELEVATOR WARNING This manual, and GENERAL INSTRUCTIONS MANUAL, CA-1, should be read thoroughly prior to pump installation, operation or maintenance. SRM00059
More informationhttps://quickserve.cummins.com/qs2/pubsys2/xml/en/procedures/40/ tr.html
Page 1 of 7 NOTE: The timing pin is used to accurately locate TDC for setting the overhead. The timing pin is typically located below the fuel pump. for front gear train engines, in the front gear housing
More informationOPERATION MANUAL for MANUAL LEVELING SYSTEMS with square foot pads on jacks
OPERATION MANUAL for MANUAL LEVELING SYSTEMS with square foot pads on jacks Dewald manual system touchpad #140-1179 Visit us on the web at www.powergearus.com 82-L0377 REV.0B 2 TABLE OF CONTENTS Page 3:
More informationTeile und Zubehör - Einbauanleitung
Teile und Zubehör - Einbauanleitung F 38 0027 EVA BMW Parts and Accessories Installation Instruction Park Distance Control (PDC), rear BMW 7 Series (E38) Best.-Nr. 01 29 0 000 791 XII/98 Printed in Germany
More informationOnboard power supply management
Onboard power supply management The onboard power supply J519 Functions of onboard power supply control unit Until now s and relays functioned at different locations in the vehicle. In the onboard power
More informationbikespeed-realspeed Instructions for the installation and description of the functions for Yamaha PW-X midengine year 2017 with Yamaha PW-X display
bikespeed-realspeed Instructions for the installation and description of the functions for Yamaha PW-X midengine design year 2017 with Yamaha PW-X display for further information visit date: 31.08.2017
More informationTechnical Instructions. SQV Series Electromotive Valve Actuators. Document No
Document No. 155-521 (For Use with 2-1/2-Inch to 6-Inch Pressure Independent Control Valves) Features Operating voltage: AC/DC 24V Application Control signals: 3-position, DC 0 to 10V, DC 4 to 20 ma Fail-safe
More informationSpear & Jackson 37 cc Petrol Chainsaw Original Operating Instructions
Spear & Jackson 37 cc Petrol Chainsaw Original Operating Instructions Assembly Manual After Sales Support UK/Ireland 0151 649 1500 Republic of Ireland 1890 946 244 Web www.einhell.co.uk Important - Please
More informationOperating Instructions T4 2x2 English V.1.0
Operating Instructions T4 2x2 English V..0 Headquarters Branch Office : Production : DEGONDA-REHAB SA DEGONDA-REHAB SA DEGONDA-REHAB SA Av. Du Rond-Point 8 2, ch. Louis-Hubert Aarestrasse 59 CH-006 Lausanne
More information