Turny Evo. Autoadapt. Seat lift. Installation manual

Transcription

1 Turny Evo Autoadapt Seat lift EN Installation manual

2

3 Getting seated Turny Evo Thank you for choosing a Turny Evo from Autoadapt! The manual that follows is an integral, important part of the product, providing you with information on how to perform accurate and safe installation of the product. Please read through the manual carefully before starting your work. EN Index If you have any questions about your customer s adaptation, please feel free to contact Autoadapt. Your feedback is important to us. It helps us in our work of continuously improving our product and its installation. You can find more information about us and our range of car adaptation solutions by visiting Once again, thank you for placing your confidence in our products! Autoadapt S A F E V E H I C L E I O N A D A P TA T Safe vehicle adaptation solutions For your safety Autoadapt products are designed and tested according to current directives and standards. Installation Technical specification Fit wiring in the car Install the bracket in the car 5 Connect Turny Evo 6 Activate the emergency-mode operation menu to install 7 Install Turny Evo on the bracket 7 Mount seat 8 Mount seat belt 0 Mount footrest and covers Exit the emergency operation menu 5 Programme Turny Evo 8 Update the software 9 Troubleshooting 0

4 Turny Evo Getting seated Installation. Fit wiring in the car Fit wiring for the hand held control, door switch, ground and V. The illustration below shows the associated connection points in the unit. For a complete wiring diagram, see the back of the manual. A / Option --optional function Hand held control The small magnet is for hanging up the hand held control. Position in a suitable place in the car s panel and tightly screw from the back. B / Lower anchor point --is connected later C / Female connector --is connected later Door switch Black cable Adjust the length of the cable and connect to the negative pole on the car battery. C B Red cable V Adjust the length of the cable and connect to A the positive pole on the car battery. Wire in the supplied fuse in close proximity to the car battery. Note! Next to the swivel motor there is a rolled cable. This cable is for a future accessory and is not used at present.. Install the bracket in the car To install Turny Evo a bracket between the product and the floor of the car is required. We recommend a car specific bracket. In cases where there is no car specific bracket, a universal bracket is available. For a range of brackets, please see dealerweb.autoadapt.com To install the bracket, follow the relevant instructions that accompany the bracket.

5 Getting seated Turny Evo 5. Connect Turny Evo Put Turny Evo on top of the bracket in the car and connect the wiring for the hand held control, door switch and V to the unit. Upon delivery Turny Evo is preprogrammed enabling it to be run once the hand held control is connected. EN Installation Optional function buttons light up GREEN. Hold the selected button down. When the seat reaches its preprogrammed end position, it will stop automatically. To stop movement, release the button. Turny Evo's location in the vehicle on the right or left side determines the functions of buttons and. COMFORT forwards SWIVEL in or out SWIVEL in or out COMFORT backwards

6 6 Turny Evo Getting seated. Activate the emergency-mode operation menu to install To access all attachment points for installation Turny Evo must be emergency controlled. Be careful when manoeuvring the unit back into the car so that the lift is done correctly, see below. IN 0 5 Lift OK Crash safety pin OUT The illustration on the left shows a fully swivelled in Turny Evo where the crash safety pin has locked the seat in the correct position.. Activate the emergency-mode. Manoeuvre Turny Evo operating menu Hold down the yellow button until the picture enter code is displayed. Then enter the code,,, Switch between movements and directions to run the unit. Note that the symbols for in" and "out" are laterally inverse in a left-side Turny Evo. Select movement Lift Swivel Lengthwise Activate direction Up Down In Out Backwards Forwards

7 Getting seated Turny Evo 7 5. Install Turny Evo on the bracket Run the unit forwards and backwards to reach the attachment points on the base plate. Install Turny Evo using the nuts and bolts supplied with the bracket. EN Installation Run the unit backwards to uncover the attachment points for the bracket at the front. Run the unit forwards to uncover the attachment points for the bracket at the rear. st st BACK FRONT st st 6. Mount seat Swivel out and lower Turny Evo slightly to reach the attachment points for seat, belt and then covers. Fit the seat using the nuts and bolts supplied with the seat. A / rear holes --BEV seat --Compact seat --Adapter plate for Recaro seat A / front holes --Adapter plate for Carony system A B

8 8 Turny Evo Getting seated 7. Mount seat belt Always strive to achieve the following seat belt geometry as illustrated below. Specified degrees are obtained from the legal requirement / ECE R-, Revision 5, seat belt attachment points Female connector Lower anchor point If the original belt has any kind of belt pretensioner or switch, the wiring must be adapted for connecting to the Turny Evo. The illustration on the next page shows a right-swivelling Turny Evo. 7. Cut off original connectors 7. Wire in new connections 7. Mount belt Cut off original connectors on lower anchor point, female connector and associated wiring on the floor under the seat. Replace original connections according to the illustration on the next page with supplied wire in connections. Ensure that the cable colours on the wire in connections match the same cable on Turny Evo. Mount according to the illustration on the next page using supplied z-iron, nuts, bolts. Use a washer if the hole pattern in OEM belt attachment is too big for the nut.

9 Getting seated Turny Evo 9 EN Installation A Energy bracket x B Energy bracket x C 7/6 UNF x x D 7/6 UNF x E.5x6x x (if necessary) Wire in connections x E.g. B / female connector with belt pretensioner and switch. Wirning from Turny Evo. E.g. B / lower anchor point with belt pretensioner. Loosen the cable, located on the lift motor and attach it to the plate. E.g. OEM wiring under seat.

10 0 Turny Evo Getting seated 8. Mount footrest and covers Note! To reach all attachment points the Turny Evo must be swivelled out and lowered slightly. The illustration below shows the unit fully swivelled in to more easily show the location of the covers. MODEL RIGHT Foot rest and front covers, mount in numerical order A M x 8 B M x 6 C.5 x 6 C x A x A x B x x x D x Tighten the screws indicated with arrows first when the footrest is in place. D M5 x 6 E x E M6 x 8

11 Getting seated Turny Evo EN MODEL RIGHT Rear covers, mount in numerical order Installation A M x 8 B M x 6 F x 6 A x F x A x A x B x

12 Turny Evo Getting seated Note! To reach all attachment points the Turny Evo must be turned out and lowered slightly. The illustration below shows the unit fully swivelled in to more easily show the location of the covers. MODEL LEFT Foot rest and front covers, mount in numerical order A M x 8 B M x 6 C.5 x 6 C x A x A x B x x x D x Tighten the screws indicated with arrows first when the footrest is in place. D M5 x 6 E x E M6 x 8

13 Getting seated Turny Evo EN MODEL LEFT Rear covers, mount in numerical order Installation A M x 8 B M x 6 A x A x A x A x B x

14 Turny Evo Getting seated 9. Exit the emergency operation menu When the installation has finished the Turny Evo should be again put into normal operating mode. To return to normal operating mode the criteria in paragraphs 9. and 9. must be met. Swivel the seat in 9. The seat must be lifted all the way up and swivelled all the way in. Switch between movements and directions until the "up" and in symbols have greyed out. Note that the symbol for in is laterally inverse in a left-side Turny Evo. Select movement Lift Swivel Lengthwise Activate direction Up In 9. Exit the emergency operation menu The seat must back over the starting position for the programming. A clicking sound can be heard when the seat passes over this position. Lengthwise Press or and select "lengthwise". Run the seat to the specified starting position by pressing or for "forwards" or "backwards". Press for "backwards". Run the seat backwards until the "exit" symbol lights up. If the seat stops before "exit" lights up you can override the system by forcing the seat backwards by holding in button for "backwards" for four seconds. If the exit does not light up step may have to be repeated. Starting position / Run backwards Exit Press or and select "exit". Press to confirm "exit". Turny Evo is now back in its normal operating mode. If this screen is displayed the criteria to exit the system has not been achieved. Go back and do 9. again and then step 9.. Press or to select the main menu at the top.

15 Getting seated Turny Evo 5 0. Programme Turny Evo 0. Activate the programming menu Hold down the yellow button until the enter code screen is displayed. Then enter the code,,, EN Installation 0. Programme movement paths Turny Evo has three motors, a lengthwise, swivelling and lifting motor. These motors must be programmed to create two separate movement paths for the seat, a comfort and a "swivel out". The movement path "comfort" is the lengthwise path that the seat follows when the car door is closed. The movement path "swivel out" is the combined swivelling and lifting path that the seat follows when the car door is open. Programme the swivel and lift movement as close as possible to the B pillar to maximise the legroom. The programmed path can vary by +/- 5 mm. Programme with an approx. 5 mm margin to prevent damage to the product and car. If you transfer to and from Turny Evo using a wheelchair, programme so that the seat stays below the wheelchair's seat height. There is also a margin to cope with transferring on uneven surfaces. Use "gradually swivel out" first to achieve a gentle, smooth movement path. At the same time, always strive to keep the programming simple with as few steps as possible for the same reason. Fewer steps also minimises the risk of errors arising in the program. When first programming it can be difficult to achieve the optimal path. There is therefore the ability to save programming at any time and then directly go into editing mode to do any fine tuning required. B pillar

16 6 Turny Evo Getting seated Program movement path, comfort Confirm starting point. Press for "backwards" until the screen comes up. Correct starting position. Use and, "forwards and "backwards", to run to the desired front end position. (When screen comes up it is possible to save the end position) Press to "save" and continue programming. (Screen comes up) 5 Use and, "forwards and "backwards", to run to the desired rear end position. (When screen 5 comes up it is possible to save the end position) Tips! The rear end position is the starting position for "swivel out" below. Mark this starting position with a piece of tape. This marking can be useful in the event of any editing of the "swivel out" path. Press to "save" and continue programming. (Screen 6 comes up) Program movement path, swivel out Switch between screen 6 and 7 to program this path. 6 Gradually swivel out Forwards Backwards Lengthwise/swivel The figure in the left corner shows how many degrees the seat is swivelled out. The seat must be swivelled out 5 degrees before lifting is possible. Press to select in the main menu at the top. Press to activate selected direction (displayed as a large symbol to the right of the screen). Press for "sequentially swivel out" (+ at a time). Press to select direction "gradually swivel out", "forwards" or "backwards". "Gradually swivel out" is a combined swivel and forward movement. We recommend first using this swivel first to achieve a gentle, smooth movement path. 7 Lift Press or to select the main menu at the top. Press for "down". Press for "up". 8 Exit Press to select in the main menu at the top. Press to save and exit from the programming mode. Turny Evo is now back in its normal operating mode.

17 Getting seated Turny Evo 7 Edit movement path, comfort The front end position allows you to edit and save separately, steps 9-. To edit and save the rear end position, steps -, editing of the front end position is required first. 9 0 Run the seat in normal operating mode and swivel the seat fully into the car. Activate the programming menu. Hold down the yellow button in the middle of the hand held control until the "enter code" screen is displayed. Then enter the code,,, (Screen 0 comes up) Use and, "forwards" and "backwards", to run to the desired front end position. (When screen comes up it is possible to save the new end position) EN Installation Alternative A - Press to "save" and exit from the programming mode. Turny Evo is now back in its normal operating mode. Alternative A - Press to "save and continue" and program rear end position. (Screen comes up) Use and, "forwards and "backwards", to run to the desired rear end position. (When screen comes up it is possible to save the new end position) The rear end position must be programmed behind the starting position for "swivel out". If the end position is programmed in front of the starting point, it will not be possible to manoeuvre the seat and the programming must be done again. Movement path "swivel out" Starting point "swivel out" This starting position was previously marked with a piece of tape in the programming. Rear end position "comfort" Press to "save" and exit from the programming mode. Turny Evo is now back in its normal operating mode. Edit movement path, swivel out 5 It is possible to begin editing from any point on the path. If the first part of the programming is good you do not need to program the whole path. Swivel out in normal operating mode to the point from which new programming is preferred to be done. Activate the programming menu. Hold down the yellow button in the middle of the hand held control until the "enter code" screen is displayed. Then enter the code,,, Press for "continue". Programme new swivel and lift, see illustration 6-8. Press for cancel and exit. Press to directly enter the emergency operation menu.

18 8 Turny Evo Getting seated. Update the software To update the software in the unit a new hand held control with the new program version is required. Open the car door where Turny Evo is installed and ensure that the hand held control lights up. Replace the existing hand held control with the new one. The door must be open until step below. Activate the programming menu. Hold down the yellow button in the middle of the hand held control until the screen "enter code" is displayed. Then enter the code,,, (Screen comes up) Press for cancel and exit. Press for starting the update. Update in progress. Update finished. Close the door and open again. (Screen comes up) 5 If Turny Evo is installed on the right side of the car, it is now possible to start programming movement paths, see chapter 0. If Turny Evo is installed on the left side of the car you must inform the system about this, see next step below. 6 7 Activate the programming menu. Hold down the yellow button in the middle of the hand held control until the "enter code" screen is displayed. Then enter the code,,, (Screen 6 comes up) Press for "continue" installation. Press for "OK". (Screen 7 comes up) 8 Start programming of movement paths, see chapter 0. Note that the choice of installation "left" is only saved if programming is done in direct connection to the choice. If this is not done in direct connection you must go in and select the "left" installation again.

19 Getting seated Turny Evo 9. Troubleshooting Warnings/error messages Warning, the backrest is reclined too far. Lifting movement out is stopped. Lift up is still possible. Warning, Incomplete seat swivel-in. Turny Evo is not in a crash-safe position. The symbol is laterally inverse on a left-side Turny Evo. Low battery charge. Recommended action Raise the backrest. Raise the seat again if it is difficult to get to the knob. Swivel the seat all the way in. Charge the vehicle battery. EN Installation. Hand held control spiral-haped cable break.. Connection problems between the hand held control and the circuit board.. Swivel motor blocked.. Swivel motor pulse generator error.. Lift motor blocked.. Lift motor pulse generator error. Lengthwise adjustment motor blocked.. Lengthwise adjustment motor pulse generator error. Swivel motor pinch protection activated.. Replace the cable.. Contact your installation technician.. Check that there are no obstructions.. Check the connector to ensure that no cables are loose.. Follow the emergency operation instructions. Contact your installation technician if the fault persists. Lift motor pinch protection activated. Lengthwise adjustment motor pinch protection activated. When encountering an obstruction, Turny Evo will stop and back a little. Remove the obstruction and try again. Cable break or limit switch for the swivel motor out of service. Cable break or limit switch for the lift motor out of service. Cable break or limit switch for lengthwise adjustment motor out of service. Follow the emergency operation instructions. Contact your installation technician if the error persists.

20 0 Turny Evo Getting seated Warnings/error messages Recommended action Swivel motor overloaded. Lift motor overloaded. Lengthwise adjustment motor overloaded Make sure there are no obstructions and try again with an empty seat. Contact your installation technician if the error persists. Swivel motor switch activated in wrong position. Lift motor switch activated in wrong position. Follow the Emergency Operation with Hand Control instructions to reset Turny Evo's start position. Contact your installation technician if the error persists. Lengthwise adjustment motor switch activated in wrong position. Turny Evo has lost its position. Follow the Emergency Operation with Hand Control instructions to reset Turny Evo's start position. Contact your installation technician if the error persists. Technical specification From above, swivelled out to the right 5. cm From behind, swivelled out to the right and lowered 70. cm 6. cm 9 cm Length with retracted foot rest cm Width cm Swivel increments...0- Installation height, up to seat attachment cm Lift height...9 cm Lengthwise movement... cm * Weight capacity refers to the total weight of the seat, its accessories and the user. Product weight... 8 kg Weight capacity*...80 kg Max power consumption... A Power consumption at rest ma Fuse...5A Power requirements... V

21 Getting seated Turny Evo EN Installation

22 Wiring diagram Turny Evo Door Switch Installation (illustrate door open) 009 Door Safety Switch Wire Collor List SB = Black GN = Green BN = Brown Y = Yellow R = Red OR = Orange W = White GR = Grey Y-GN = Yellow/Green 66 X = No Connection Interface Vehicle Interface Turny 75 Limit Switch Rotation 75 Limit Switch Lift 75 Limit Switch Length 856 C0 58 Limit Switch Seat Back,7 K Ω,7 K Ω,7 K Ω 857 C9 857 C7 857 C8 857 C6 856 C8 856 C9 GND +V 856 C Fuse 5A 580 Wire SB 6 mm² 580 Wire R 6 mm² Wire SB mm² 856 Wire SB mm² 856 Wire SB mm² 856 Wire SB mm² 856 C 856 C 856 Wire 5 R mm² 856 Wire 6 SB mm² 857 Wire 5 SB mm² 857 Wire 6 SB mm² 857 Wire 7 SB mm² 857 Wire Y-GN mm² 856 Wire 9 GR mm² 856 Wire 0 GR mm² 856 Wire 8 Y-GN mm² 856 Wire 7 SB mm² 58 Wire SB 0,5 mm² 58 Wire SB 0,5 mm² 856 C6 856 C5 856 Wire 5 SB mm² 856 Wire 6 SB mm² 856 C 857 C 857 C 856 C5 856 C C 856 C8 856 C7 856 Wire 5 SB,5 mm² 856 Wire 6 R,5 mm² X X X X X5 X6 X Power Supply Limit Switch Rotation Limit Switch Lift Limit Switch Length Door Switch GND Seat Back Out Of Position Motor Rotation 86 Power Module X X X X6 X0 Interface Turny Interface Vehicle

23 Motor Length Motor Left Side Version = 8 Length Motor Right Side Version = 8 Rotation Motor Left Side Version = 6 Rotation Motor Left Side Version = 7 Interface Hand Control 009 Wire W 0, mm² 009 Wire BN 0, mm² 009 Wire GN 0, mm² 009 Wire Y 0, mm² 009 C X 5 X Hand Control en 009 C Rotation Motor Length Motor 859Lift Motor M M M 856 C 5 6 Interface Vehicle Interface Turny Remote +V 857 C5 856 C7 857 C XXXXXX 6 5 SB = 0V R = +V OR = UP W = Right 5 Y = Left 6 GR = Down GND X X7 X5 X9 X8 X X8 X0 X Motor Rotation Pulse Sensor Rotation Motor Length Pulse Sensor Length Motor Lift Pulse Sensor Lift Spare Hand Control 5 6 Remote 857 C 857 C 856 C 856 C C6 857 C0 857 Wire SB mm² 857 Wire SB mm² 857 Wire SB mm² 856 Wire SB,0 mm² 856 Wire SB,0 mm² 856 Wire SB,0 mm² 856 Wire SB,0 mm² 857 Wire 9 SB 0,5 mm² 857 Wire 0 R 0,5 mm² 857 Wire OR 0,5 mm² 857 Wire W 0,5 mm² 857 Wire Y 0,5 mm² 857 Wire GR 0,5 mm² 857 Wire SB mm² 856 Wire GR mm² 856 Wire GR mm² 856 Wire GR mm² 856 Wire GR mm² 859 Wire SB,5 mm² 859 Wire R,5 mm² 859 Wire Y 0,5 mm² 859 Wire GN 0,5 mm² 859 Wire R 0,5 mm² 859 Wire SB 0,5 mm² X X X X X9 X7 X8 X5 X8 M9 X5 X X Interface Turny Interface Vehicle

24

25 976 ISO/IEC 705 Accredited by SWEDAC as testing laboratory in accordance with ISO/IEC 705:005 Quality system certified in accordance with ISO 900:008 Illustrations, descriptions and specifications in the user manual are based on current product information. Autoadapt reserves the right to make alterations without previous notice. 05 Autoadapt AB

26 8-05/0 EN facebook.com/autoadapt twitter.com/autoadapt AUTOADAPT AB Åkerivägen 7 S- 6 Stenkullen Sweden Phone: info@autoadapt.com