Return line filter for direct tank mounting Type ABZFR

Transcription

1 RE 5 8/. Replaces: 7.99 Return line filter for direct tank mounting Type ABZFR Maximum operating pressure 5 bar Maximum flow 5 l/min H69+69.tif Return line filter type ABZFR Table of contents Contents Page Features Ordering code Symbols Function, section Technical data Characteristic curves 5 Unit dimensions 6 and 7 Clogging indicator; spare parts 8 Features Return line filters of type ABZFR are designed for mounting onto fluid reservoirs. They are used to separate solid matter from the hydraulic fluid that is flowing back into the tank. They have the following features: Filter elements based on inorganic fibre Excellent separation characteristics (b-values) over a wide differential pressure range High contamination retention capacity due to large specific filter surface area Good chemical resistance of the filter elements due to the use of epoxy resins for impregnation and bonding High bursting pressure resistance of the filter elements (e.g. during cold start) Water and water traces in the hydraulic fluid do not cause a reduction in the filtration capacity µm filter rating absolute by Bosch Rexroth AG, Industrial Hydraulics, D-978 Lohr am Main All rights reserved. No part of this document may be reproduced or stored, processed, duplicated or circulated using electronic systems, in any form or by any means, without the prior written authorisation of Bosch Rexroth AG. In the event of contravention of the above provisions, the contravening party is obliged to pay compensation. ABZFR /8 RE 5 8/.

2 Ordering code Return line filter Rexroth plant construction accessories ABZ F R X Filter Return line filter Return line filter, single = S Return line filter, duplex = D Size (flow at p =. bar / 9 mm /s) Series 5 = 5 Series = Series 5 = 5 A = B = Hydraulic fluid M = See table (page ) V = See table (page ) X = Series to 9 ( to 9; unchanged installation and connection dimensions) = Filter element (rating in micron absolute) (return line filter) ABZFR-S5--X/M-A ABZFR-S--X/M-A ABZFR-S5--X/M-A R9955 R99555 R99556 (return line filter) ABZFR-S5--X/M-B ABZFR-S--X/M-B ABZFR-S5--X/M-B R9957 R9957 R9957 Clogging indicator Rexroth plant construction accessories Filter Clogging indicator Visual backpressure indicator with cracking pressure p = to bar Electrical backpressure switch with cracking pressure p = to bar Only use filter with the clogging indicator fitted! ABZ F V X = RV = RE A = B = No code = Hydraulic fluid All hydraulic fluids See table (page ) M = See table (page ) V = See table (page ) X = Series to 9 ( to 9; unchanged installation and connection dimensions) (clogging indicator) (clogging indicator) ABZFV-RV-X/M-A (optisch) ABZFV-RE-X/M-A (elektrisch) R997 R9965 ABZFV-RV-X/B (optisch) ABZFV-RE-X/M-B (elektrisch) R9966 R9967 Order example: Return line filter for a flow of 5 l/min with mµ filter element for hydraulic fluid, mineral oil HLP to DIN 55 and clogging indicator variant A. Filters and clogging indicators of : ABZFR-S5--X/M-A Material number: R9955 variants A and B cannot combined : ABZFV-RE-X/M-A Material number: R9965 with each other : Leitungsdose Z Material number: R95858 Plug-in connectors for mounting on electrical clogging indicators, variants A and B Designation: Material number Plug-in connector DC voltage AC voltage Material number Cable length 5m Cable length m Z (standard) V R96 R95858 R979 without circuitry ZL V R965 R97 with indicator lamp Z5L V R95585 with indicator lamp V R95587 V R95588 For technical data and unit dimensions, see data sheet RE 8 6, pages 5 and 6. RE 5 8/. /8 ABZFR

3 Symbols A Visual backpressure indicator Return line filter B Electrical backpressure switch P PE PE Plug-in connectors type Z... Z gn ge ZL PE ge gn Z5L -N PE Function, section These return line filters are designed to be directly mounted onto the fluid tank. They basically consist of the filter housing (), cover () with connection for backpressure indicator (), filter element (), strainer (5 ) ) as well as clogging indicator (6) (connection provided as standard). The filter elements comprise by-pass valves (7). The hydraulic fluid is fed via port A to the filter element (), where it is filtered in accordance with the relevant filter rating. The dirt particles filtered out settle in the strainer (5) ) and filter element (). The filtered hydraulic fluid is directed via port B to the tank. When the filter element () is taken out, the strainer (5) ) is pulled out as well, which prevents the settled dirt particles from entering the tank. A 6 7 ) only 5 ) B Only use filter with the clogging indicator fitted! ABZFR /8 RE 5 8/.

4 Technical data (for applications outside these parameters, please consult us!) General Installation position Direction of flow Vertical Inlet at the side, outlet vertically downwards Weight Series 5 5 kg... kg.6.. Hydraulic Maximum operating pressure bar 5 5 Cracking pressure of the by-pass valve bar +.5. ±. Response pressure of the clogging indicator bar.. ±. Temperature range C to + to+ Electrical Electrical connection to DIN 65 Plug-in connection, -pin + PE Contact load AC voltage 6 A at V resistive load Type of switching DC voltage Max. switching voltage V Type of protection (to DIN 5) Max. switching capacity at resistive load 6 A at V resistive load Make-contact or break-contact, switching contacts (changeover contacts) IP 65 (when using a plug-in connector) In the case of DC voltage above V provide a spark suppressor to protect the switching contacts. VA; 5 W Filter element Filter element Disposable element based on inorganic fibre Retention rate β to p = 5 bar Permissible pressure differential bar 5 bar β to p = bar Weight Series 5 5 kg kg.5.. Hydraulic fluids Mineral oils Mineral oil HL/HLP to DIN 55 M M Hardly inflammable hydraulic fluids Emulsions HFA-E to DIN M M Synthetic aqueous solutions HFA-S ) ) Viscosity-adjusted HFA fluids HFA-V V V Aqueous solutions HFC to VDMA 7 M M Phosphate esters HFD-R to VDMA 7 V ) Organic esters HFD-U to VDMA 7 V ) Fast bio-degradable hydraulic fluids Triglycerides (rape seed oil) HETG to VDMA 568 V ) Synthetic esters HEES to VDMA 568 V ) Polyglycols HEPG to VDMA 568 V ) ) Enquiry stating the hydraulic fluid RE 5 8/. /8 ABZFR

5 Characteristic curves measured with mineral oil HLP 6 to DIN 55 at ϑ oil = 5 C (ν = 9 mm /s) ABZFR-S5--X/M-A,6,,,, Variants A and B Flow in l/min,,5,,5,,5, Variants A and B Flow = 5 l/min Temperature in C 9 ABZFR-S--X/M-A,6,,,, Flow in l/min 8,5,,5,,5,,5, Flow = l/min Temperature in C 9 ABZFR-S5--XM-A,6,,,, Flow in l/min,,5,,5,,5, Flow = 5 l/min 5 6 Temperature in C ABZFR 5/8 RE 5 8/.

6 Unit dimensions (Dimensions in mm) ABZFR-S5--X/..-A ABZFR-S--X/..-A ABZFR-S5--X/..-A h h5 h h5 b b d6/ h h d/t h d d/t Ø d d/t b d5 h O-ring seal h h Flat seal Ø d d b d5 d Space for clogging indicator Minimum space required to remove element Inlet Outlet Type b b b Ød ) Ød Ød Ød d5 ) ABZFR-S5--X/..-A G / ) G / ) M5 ABZFR-S--X/..-A 7 + G / ) G / ) 5 M6 ABZFR-S5--X/..-A SAE ) G ) M Type d6 h h h h h5 t ABZFR-S5--X/..-A Ø ABZFR-S--X/..-A Ø ABZFR-S5--X/..-A M ) Threaded connection to ISO 8 ) Standard pressure series ) Drilling for fixing screws ) Tank opening RE 5 8/. 6/8 ABZFR

7 Unit dimensions (Dimensions in mm) ABZFR-S5--X/..-B ABZFR-S--X/..-B ABZFR-S5--X/..-B 5 b d/t h h h h h5 5 d h h h h h5 b 5 b d d6 h h h h h5 d/t d/t d/t d d Ød d5 8 d b d b d5 d b d5 SW SW SW Space for clogging indicator Minimum space required to remove element Inlet Outlet 5 O-ring seal Type b b b b Ød 5) Ød ) Ød Ød d5 ) ABZFR-S5--X/..-B G / ) R ) M5 ABZFR-S--X/..-B G ) G / ) M8 ABZFR-S5--X/..-B SAE ) G / ) 8. M Type d6 h h h h h5 t A/F ABZFR-S5--X/..-B ,6 6 ABZFR-S--X/..-B ABZFR-S5--X/..-B M ) Threaded connection ) Threaded connection ) Standard pressure ) Drilling for 5) Tank opening to ISO 7 to ISO 8 series fixing screws ABZFR 7/8 RE 5 8/.

8 Clogging indicator Visual backpressure indicator (pressure gauge) 5 Electrical backpressure indicator 5 Visual backpressure indicator (pressure gauge) 6 (Dimensions in mm) Electrical backpressure indicator Spare parts Filter element 6,5 A/F 9, maximum tightening torque M T max = Nm A/F 9, maximum tightening torque M T max = 5 Nm A/F, maximum tightening torque M T max 5 Nm Note: ABZ F E R X Rexroth plant construction accessories Filter Filter element Filter element for return line filter = R Size (flow) Series 5 = 5 Series = Series 5 = 5 (filter element) ABZFE-R5--X/M-A ABZFE-R--X/M-A ABZFE-R5--X/M-A Seal kits Rexroth plant construction accessories R9976 R9977 R A = B = Hydraulic fluid M = See table (page ) V = See table (page ) X = Series to 9 ( to 9; unchanged installation and connection dimensions) = Filter element (rating in micron) (filter element) ABZFE-R5--X/M-B ABZFE-R--X/M-B ABZFE-R5--X/M-B ABZ F Z D R X Filter Accessories/miscellaneous Seal kit = D Size (flow) Series 5 = 5 Series = Series 5 = 5 Pressure gauge can be rotated through ca. 5 for alignment. 5 A/F, maximum tightening torque M T max = 5 Nm 6 A/F, maximum tightening torque M T max = 5 Nm Adjust and fix using only the spanner flats provided. The specified tightening and adjustment torques must not be exceeded. R = 6 R996 R9976 R99765 A = B = Hydraulic fluid M = See table (page ) V = See table (page ) X = Series to 9 ( to 9; unchanged installation and connection dimensions) Return line filter ) (seal kit) ABZFZ-D5-R-X/M-A ABZFZ-D-R-X/M-A Bosch Rexroth AG Industrial Hydraulics D-978 Lohr am Main Zum Eisengießer D-9786 Lohr am Main Telefon 9 5 / 8- Telefax 9 5 / 8-58 Telex documentation@boschrexroth.de Internet R99758 R99759 ABZFZ-D5-R-X/M-A R9976 ABZFZ-D5-R-X/M-B ) The seal kit consists of three O-rings for the element, cover and clogging indicator and a tank seal. ) The seal kit consists of two O-rings for the cover and clogging indicator and a tank seal. Bosch Rexroth Limited Cromwell Road, St Neots, Cambs, PE9 ES Tel: 8/ 56 Fax: 8/ info@rexroth.co.uk ) (seal kit) ABZFZ-D5-R-X/M-B ABZFZ-D-R-X/M-B R99659 R9966 R9966 The data specified above only serve to describe the product. No statements concerning a certain condition or suitability for a certain application can be derived from our information. The details stated do not release you from the responsibility for carrying out your own assessment and verification. It must be remembered that our products are subject to a natural process of wear and ageing. RE 5 8/. 8/8 ABZFR