Babcock-Plaxton Panther Installation Guide

Size: px

Start display at page:

Download "Babcock-Plaxton Panther Installation Guide"

Aubrey Walker
5 years ago
Views:

1 Babcock-Plaxton Panther Installation Guide Manufactured by Plaxtons the Panther is built on a Volvo chassis This guide applies to 2014> models Equipment to be installed comprises of a TVG with TDI and Can Bus connection Panther Installation Guide-Page 1 of 13

2 Interior View and Equipment Locations TVG - Rear of centre console TDI - Drivers A pillar Antennas - Beneath front dash Antennas TDI Six way power and Can bus connector - Rear of centre consul The six way connector is provided by Plaxton during build Six pin connector TVG Panther Installation Guide-Page 2 of 13

3 Dashboard Facia Removal Remove 14x Philips screws that secure Dash Facia as indicated in Illustration Extra care is needed when screws have been removed to prevent panels marking the dash Panther Installation Guide-Page 3 of 13

4 Lower Dashboard Removal The lower dash is accessed by removing 2 x flat blade screws which allows the nearside panel to be removed Panther Installation Guide-Page 4 of 13

of the TDI cable using Tessa Tape and secure to

5 TDI Installation The TDI is adhered to the drivers A pillar using the pad provided Tape the first 8-10 cm of the TDI cable using Tessa Tape and secure to bracket with a cable tie Panther Installation Guide-Page 5 of 13

6 TDI Installation Feed TDI cable down the front of the dashboard There is sufficient space between dash and screen to feed the TDI connectors Route the cables with existing vehicle loom to the TVG location Panther Installation Guide-Page 6 of 13

tape is to be applied to secure the antennas Route cables to

7 Antenna Installation Both GPS & GPRS antennas are adhered to the flat surface above heater outlets View from Below Gaffer tape is to be applied to secure the antennas Route cables to TVG location View through Dash Panther Installation Guide-Page 7 of 13

Power & FMS Connection A Six way plug containing the Power and FMS connections is supplied by plaxtons and is located to the rear of the Centre Dash area A number of C730 has been issued to this plug

8 Power & FMS Connection A Six way plug containing the Power and FMS connections is supplied by plaxtons and is located to the rear of the Centre Dash area A number of C730 has been issued to this plug and written on Pin 1-Red= Permanent Pin 2-Yellow= ignition Pin 3-Red= Can High Pin 4-Black= Can Low Pin 5-Empty Pin 6-Black= Ground Red and Black twisted pair for FMS Pins 3&6 is ran in grey insulation and the wires are noticeably thinner Panther Installation Guide-Page 8 of 13

connect to the C730 plug Refer to Page 8 for pin outs DO NOT CONNECT TO TVG UNTIL

9 Power & FMS Connection THIS IS AN APPROVED CONNECTION TYPE TO ENSURE THE VEHICLE WARRANTY IS NOT COMPROMISED Using a Six way plug and pins available from Plaxtons connect to the C730 plug Refer to Page 8 for pin outs DO NOT CONNECT TO TVG UNTIL ALL POWER AND FMS HAS BEEN TESTED FOR CORRECT POLARITY Panther Installation Guide-Page 9 of 13

F133=Permanent Fuse location F137=Ignition Both of these locations require a

10 Fuse Board Allocations The fuse Board for the TVG power supply is located in the luggage storage area behind driver at ceiling level Fuse location F133=Permanent Fuse location F137=Ignition Both of these locations require a 3amp fuse fitting Test power at plug C730 F133 F137 Panther Installation Guide-Page 10 of 13

speed fasteners From the inside of the storage area use the TVG as a template

11 Mounting the TVG At the bottom of the Centre Console is a storage area for a First Aid box The TVG is to be mounted on the rear of this storage area using speed fasteners From the inside of the storage area use the TVG as a template mark and drill 2 x 1/8 holes for the TVG fixing screws Panther Installation Guide-Page 11 of 13

storage area using 2 x self tapping screws into the 2 x speed

12 Mounting the TVG Apply 2 x speed fasteners to the TVG After all cables are connected the TVG is ready to mount to the rear of storage area using 2 x self tapping screws into the 2 x speed clips that are attached to the TVG Panther Installation Guide-Page 12 of 13

13 Program and Testing Program TVG and test for correct operation including data from FMS Ensure the test code is documented Neatly loom and secure all excess cable Apply anti tamper seal to all connections Replace all panels and screws to the vehicle Carry out post installation checks Leave the work area clean and tidy For further information regarding this guide contact - Peter Dryden peterd@nationwideservicecare.com Panther Installation Guide-Page 13 of 13

GreenRoad Installation Document (GRID) Document Number: VWR10

GreenRoad Installation Document (GRID) Document Number: VWR10 Chassis: Volvo B10BLE Version Created By Date Body: Wright Renown 1.0 JP 15/06/2011 Year: 1998/2000 Configuration: Single Deck Bus Adherence