Ruud Commercial Achiever Series Package Air Conditioner. Package Air Conditioner

Transcription

1 Package Air Conditioner Ruud Commercial Achiever Series Package Air Conditioner RLKN-B Standard Efficiency Series Nominal Sizes 6 Tons [21.1 kw] (3 Phase Models Only) Rely on Ruud. FORM NO. S REV. 1

2 Table of Contents TABLE OF CONTENTS Unit Features & Benefits Selection Procedure...5 Model Number Identification...6 Options...7 General Data Gross Systems Performance Data...10 Airflow Performance...11 Electrical Data...12 Electric Heater Kits Dimensional Data Accessories Mechanical Specifications...26 Limited Warranty Rely on Ruud.

3 Unit Features & Benefits Compressor Access Non-corrosive plastic condensate pan Evaporator Coil/Filter Access Return air filters, normally provided, are removed in this photo. Optional Electric Heater Kit Blower Access Rely on Ruud. 3

4 Unit Features & Benefits STANDARD FEATURES INCLUDE: R-410A HFC refrigerant. Complete factory charged, wired and run tested. Scroll compressors with internal line break overload and high-pressure protection. Two-stage compressor on all models. Convertible airflow. TXV refrigerant metering system. High Pressure and Low Pressure/Loss of charge protection standard on all models. Solid Core liquid line filter drier on each circuit. Single slab, single pass designed evaporator coil facilitates easy cleaning for maintained high efficiencies. Cooling operation up to 125 degree F ambient. Easily removable filter, blower, electric heat, and control access panels permits prompt service. Powder Paint Finish meets ASTMB117 steel coated on each side for maximum protection. G90 galvanized. One piece top cover and one piece base pan with drawn supply and return opening for superior water management. Externally mounted refrigerant gauge ports for easy service diagnostics. Factory or field-installed electric heat kits available up to 24 kw. Easy to install plug-in; slip in, 100% fully modulating economizer. Forkable base rails for easy handling and lifting. Single point electrical and gas connections. High performance belt drive motor with variable pitch pulleys and quick adjust belt system. Permanently lubricated evaporator, condenser and gas heat inducer motors. Condenser motors are internally protected, totally enclosed with shaft down design. 2 inch filter standard with slide out design. Colored and labeled wiring. Molded compressor plug. Micro Channel evaporators and condenser delivers superior performance with less refrigerant charge and less weight than conventional copper tube/aluminum fin coils In addition the aluminum design has superior formicary corrosion protection and less potential for leaks due to elimination of tube rubbing potential. Its easier to clean and has a more robust surface. 4 Rely on Ruud.

5 Selection Procedure RLKN-B SELECTION PROCEDURES 1. Determine cooling and heating requirements at design conditions. Example: Total cooling capacity...61,000 BTUH [17.87 kw] Sensible cooling capacity...44,000 BTUH [12.89 kw] Condenser entering air...95 F [35 C] Evaporator entering air...63 F [17 C] wb/76 F [24 C] db Indoor air flow CFM [991 L/s] External static pressure in W.G. 2. Select unit to meet cooling requirements. Since total cooling is within the range of 6 ton [21.1 kw] unit enter cooling performance from the RLKN-B073 table, at 95 F [35 C] outdoor temperature, 63 F [17 C] wb entering indoor air, and 2100 CFM [991 L/s]: Total capacity...65,000 BTUH [19.1 kw] Sensible Capacity...55,400 BTUH [16.2 kw] Power input kw And also, at 76 F [24 C] db indoor entering air, and using the formula at the bottom of the page: Sensible capacity...48,008 BTUH [14.07 kw] 3. Determine blower speed and power to meet the system requirements. At the given external static pressure of 1.0 in W.G., the belt model must be selected. Enter the belt drive blower performance table at 2100 CFM [991 L/s] and 1.0 in W.G. ESP: RPM Watts Drive...L 4. Calculate indoor blower BTUH heat effect. BTUH = Watts x = Calculate net cooling capacities. Net total cooling = 65, = 61,502 BTUH [18.02 kw] Net sensible cooling = 48, = 44,510 BTUH [13.04 kw] Rely on Ruud. 5

6 Model Number Identification R L K N B 073 C L 000 X X X Economizer Option (See Next Page) Factory Installed Options (See Next Page) Electric Heat 000 = No Resistance Heat 006 = 6 kw Resistance Heat 010 = 10 kw Resistance Heat 012 = 12 kw Resistance Heat 015 = 15 kw Resistance Heat 020 = 20 kw Resistance Heat 024 = 24 kw Resistance Heat Drive Package L = Belt Drive M= Belt Drive High Static Electrical Designation C = V, 3 PH, 60 Hz D = 460 V, 3 PH, 60 Hz Y = 575 V, 3 PH, 60 Hz Cooling Capacity (BTUH) [kw] 073 = 72,000 [21.10] Future Technical Variations Design Series N = R-410A Efficiency Designation K = Standard Efficiency Product Classification L = Packaged Air Conditioner Commercial Tradebrand R = Ruud 6 Rely on Ruud.

7 Options FACTORY INSTALLED OPTION CODES FOR RLKN-B073 (6 Ton) [21.1 kw] Option Code Hail Guard Non-Powered Convenience Outlet Low Ambient/ Freeze Stat AD x AG x AP x BY x x BJ x x CX x x x JC x x Example: RLKN-B073CL000XXX (where XX is factory installed option) Example: No Options RLKN-B073CL000 Example: No Options with Factory Installed Economizer RLKN-B073CL000AAF Example: Options with Hailguard with no Factory Installed Economizer RLKN-B073CL000ADA Example: Options same as above with Factory Installed Economizer RLKN-B073CL000ADF ECONOMIZER SELECTION FOR RLKN-B073 No Economizer A x F G x indicates factory installed option. Single Enthalpy Economizer with Barometric Relief x Single Enthalpy Economizer with Smoke Detector x Rely on Ruud. 7

8 General Data NOMINAL SIZES 6 TONS [21.1 kw] ASHRAE COMPLIANT MODELS Model RLKN- Series B073CL B073CM B073DL B073DM Cooling Performance 1 CONTINUED Gross Cooling Capacity Btu [kw] 70,000 [20.51] 70,000 [20.51] 70,000 [20.51] 70,000 [20.51] EER/SEER / NA 11.2 / NA 11.2 / NA 11.2 / NA Nominal CFM/AHRI Rated CFM [L/s] 2400/2100 [1133/991] 2400/2100 [1133/991] 2400/2100 [1133/991] 2400/2100 [1133/991] AHRI Net Cooling Capacity Btu [kw] 68,000 [19.92] 68,000 [19.92] 68,000 [19.92] 68,000 [19.92] Net Sensible Capacity Btu [kw] 46,000 [13.48] 46,000 [13.48] 46,000 [13.48] 46,000 [13.48] Net Latent Capacity Btu [kw] 22,000 [6.45] 22,000 [6.45] 22,000 [6.45] 22,000 [6.45] IEER Net System Power [kw] Compressor No./Type 1/Two-Stage Scroll 1/Two-Stage Scroll 1/Two-Stage Scroll 1/Two-Stage Scroll Outdoor Sound Rating (db) Outdoor Coil Fin Type Louvered Louvered Louvered Louvered Tube Type MicroChannel MicroChannel MicroChannel MicroChannel MicroChannel Depth [in] [mm] 0.71 [18] 0.71 [18] 0.71 [18] 0.71 [18] Face Area sq. ft. [sq. m] 16.4 [1.52] 16.4 [1.52] 16.4 [1.52] 16.4 [1.52] Rows / FPI [FPcm] 1/23 [9] 1/23 [9] 1/23 [9] 1/23 [9] Indoor Coil Fin Type Louvered Louvered Louvered Louvered Tube Type MicroChannel MicroChannel MicroChannel MicroChannel MicroChannel Depth [in] [mm] 1.26 [32] 1.26 [32] 1.26 [32] 1.26 [32] Face Area sq. ft. [sq. m] 5.95 [0.55] 5.95 [0.55] 5.95 [0.55] 5.95 [0.55] Rows / FPI [FPcm] 1/20 [8] 1/20 [8] 1/20 [8] 1/20 [8] Refrigerant Control TX Valve TX Valve TX Valve TX Valve Drain Connection No./Size in. [mm] 1/0.75 [19.05] 1/0.75 [19.05] 1/0.75 [19.05] 1/0.75 [19.05] Outdoor Fan Type Propeller Propeller Propeller Propeller No. Used/Diameter in. [mm] 1/24 [609.6] 1/24 [609.6] 1/24 [609.6] 1/24 [609.6] Drive Type/No. Speeds Direct/1 Direct/1 Direct/1 Direct/1 CFM [L/s] 4200 [1982] 4200 [1982] 4200 [1982] 4200 [1982] No. Motors/HP 1/0.5 1/0.5 1/0.5 1/0.5 Motor RPM Indoor Fan Type FC Centrifugal FC Centrifugal FC Centrifugal FC Centrifugal No. Used/Diameter in. [mm] 1/11x10 [279x254] 1/11x10 [279x254] 1/11x10 [279x254] 1/11x10 [279x254] Drive Type Belt (Adjustable) Belt (Adjustable) Belt (Adjustable) Belt (Adjustable) No. Speeds Single Single Single Single No. Motors Motor HP Motor RPM Motor Frame Size Filter Type Disposable Disposable Disposable Disposable Furnished Yes Yes Yes Yes (NO.) Size Recommended in. [mm x mm x mm] (4)2x16x16 [51x406x406] (4)2x16x16 [51x406x406] (4)2x16x16 [51x406x406] (4)2x16x16 [51x406x406] Refrigerant Charge Oz. [g] 67 [1899] 67 [1899] 67 [1899] 67 [1899] Weights Net Weight lbs. [kg] 551 [250] 553 [251] 551 [250] 553 [251] Ship Weight lbs. [kg] 579 [263] 581 [264] 579 [263] 581 [264] NOTES: 1. Cooling Performance is rated at 95 F ambient, 80 F entering dry bulb, 67 F entering wet bulb. Gross capacity does not include the effect of fan motor heat. AHRI capacity is net and includes the effect of fan motor heat. Units are suitable for operation to 20% of nominal cfm. Units are certified in accordance with the Unitary Large Equipment certification program, which is based on AHRI Standard 340/ EER and IEER are rated at AHRI conditions and in accordance with DOE test procedures and AHRI Standard 340/ Outdoor Sound Rating shown is tested in accordance with AHRI Standard Rely on Ruud.

9 General Data NOMINAL SIZES 6 TONS [21.1 kw] ASHRAE COMPLIANT MODELS Model RLKN- Series B073YL B073YM Cooling Performance 1 Gross Cooling Capacity Btu [kw] 70,000 [20.51] 70,000 [20.51] EER/SEER /NA 11.2/NA Nominal CFM/AHRI Rated CFM [L/s] 2400/2100 [1133/991] 2400/2100 [1133/991] AHRI Net Cooling Capacity Btu [kw] 68,000 [19.92] 68,000 [19.92] Net Sensible Capacity Btu [kw] 46,000 [13.48] 46,000 [13.48] Net Latent Capacity Btu [kw] 22,000 [6.45] 22,000 [6.45] IEER Net System Power [kw] Compressor No./Type 1/Two-Stage Scroll 1/Two-Stage Scroll Outdoor Sound Rating (db) Outdoor Coil Fin Type Louvered Louvered Tube Type MicroChannel MicroChannel MicroChannel Depth [in] [mm] 0.71 [18] 0.71 [18] Face Area sq. ft. [sq. m] 16.4 [1.52] 16.4 [1.52] Rows / FPI [FPcm] 1/23 [9] 1/23 [9] Indoor Coil Fin Type Louvered Louvered Tube Type MicroChannel MicroChannel MicroChannel Depth [in] [mm] 1.26 [32] 1.26 [32] Face Area sq. ft. [sq. m] 5.95 [0.55] 5.95 [0.55] Rows / FPI [FPcm] 1/20 [8] 1/20 [8] Refrigerant Control TX Valve TX Valve Drain Connection No./Size in. [mm] 1/0.75 [19.05] 1/0.75 [19.05] Outdoor Fan Type Propeller Propeller No. Used/Diameter in. [mm] 1/24 [609.6] 1/24 [609.6] Drive Type/No. Speeds Direct/1 Direct/1 CFM [L/s] 4200 [1982] 4200 [1982] No. Motors/HP 1/0.5 1/0.5 Motor RPM Indoor Fan Type FC Centrifugal FC Centrifugal No. Used/Diameter in. [mm] 1/11x10 [279x254] 1/11x10 [279x254] Drive Type Belt (Adjustable) Belt (Adjustable) No. Speeds Single Single No. Motors 1 1 Motor HP Motor RPM Motor Frame Size Filter Type Disposable Disposable Furnished Yes Yes (NO.) Size Recommended in. [mm x mm x mm] (4)2x16x16 [51x406x406] (4)2x16x16 [51x406x406] Refrigerant Charge Oz. [g] 67 [1899] 67 [1899] Weights Net Weight lbs. [kg] 546 [248] 548 [249] Ship Weight lbs. [kg] 574 [260] 576 [261] NOTES: 1. Cooling Performance is rated at 95 F ambient, 80 F entering dry bulb, 67 F entering wet bulb. Gross capacity does not include the effect of fan motor heat. AHRI capacity is net and includes the effect of fan motor heat. Units are suitable for operation to 20% of nominal cfm. Units are certified in accordance with the Unitary Large Equipment certification program, which is based on AHRI Standard 340/ EER and IEER are rated at AHRI conditions and in accordance with DOE test procedures and AHRI Standard 340/ Outdoor Sound Rating shown is tested in accordance with AHRI Standard 270. Rely on Ruud. 9

10 Gross Systems Performance Data GROSS SYSTEMS PERFORMANCE DATA RLKN-B073 O UT D OO R D RY B UL B T EM P ER A TU R E F [ C] 75 [23.9] 80 [26.7] 85 [29.4] 90 [32.2] 95 [35] 100 [37.8] 105 [40.6] 110 [43.3] 115 [46.1] 120 [48.9] 125 [51.7] ENTERING INDOOR 80 F [26.7 C] dbe ➀ wbe 71 F [21.7 C] 67 F [19.4 C] 63 F [17.2 C] 61 F [16.1 C] 59 F [15.0 C] CFM [L/s] 2310 [1090] 2100 [991] 1780 [840] 2310 [1090] 2100 [991] 1780 [840] 2310 [1090] 2100 [991] 1780 [840] 2310 [1090] 2100 [991] 1780 [840] 2310 [1090] 2100 [991] 1780 [840] DR ➀ Total BTUH [kw] Sens BTUH [kw] Power Total BTUH [kw] Sens BTUH [kw] Power Total BTUH [kw] Sens BTUH [kw] Power Total BTUH [kw] Sens BTUH [kw] Power Total BTUH [kw] Sens BTUH [kw] Power Total BTUH [kw] Sens BTUH [kw] Power Total BTUH [kw] Sens BTUH [kw] Power Total BTUH [kw] Sens BTUH [kw] Power Total BTUH [kw] Sens BTUH [kw] Power Total BTUH [kw] Sens BTUH [kw] Power Total BTUH [kw] Sens BTUH [kw] Power DR Depression ratio dbe Entering air dry bulb wbe Entering air wet bulb 84.0 [24.6] 44.8 [13.1] [24.1] 44.4 [13.0] [23.6] 43.8 [12.8] [23.0] 43.0 [12.6] [22.4] 42.0 [12.3] [21.7] 40.8 [11.9] [20.9] 39.3 [11.5] [20.1] 37.7 [11.1] [19.2] 35.9 [10.5] [18.3] 33.8 [9.9] [17.3] 31.6 [9.3] [24.2] 42.8 [12.5] [23.7] 42.4 [12.4] [23.2] 41.9 [12.3] [22.6] 41.1 [12.0] [22.0] 40.1 [11.8] [21.3] 39.0 [11.4] [20.6] 37.6 [11.0] [19.8] 36.0 [10.6] [18.9] 34.3 [10.0] [18.0] 32.3 [9.5] [17.0] 30.2 [8.8] [23.5] 39.8 [11.6] [23.1] 39.4 [11.5] [22.6] 38.9 [11.4] [22.0] 38.2 [11.2] [21.4] 37.3 [10.9] [20.7] 36.2 [10.6] [20.0] 34.9 [10.2] [19.2] 33.5 [9.8] [18.4] 31.8 [9.3] [17.5] 30.0 [8.8] [16.5] 28.0 [8.2] 7.8 Total Total capacity x 1000 BTUH Sens Sensible capacity x 1000 BTUH Power KW input 79.1 [23.2] 53.3 [15.6] [22.7] 52.9 [15.5] [22.2] 52.3 [15.3] [21.6] 51.5 [15.1] [21.0] 50.5 [14.8] [20.3] 49.3 [14.5] [19.5] 47.9 [14.0] [18.7] 46.3 [13.6] [17.8] 44.4 [13.0] [16.9] 42.4 [12.4] [15.9] 40.1 [11.8] [22.8] 51.0 [14.9] [22.3] 50.6 [14.8] [21.8] 50.0 [14.7] [21.2] 49.2 [14.4] [20.6] 48.3 [14.1] [19.9] 47.1 [13.8] [19.2] 45.8 [13.4] [18.4] 44.2 [13.0] [17.5] 42.4 [12.4] [16.6] 40.5 [11.9] [15.6] 38.3 [11.2] [22.1] 47.3 [13.9] [21.7] 47.0 [13.8] [21.2] 46.5 [13.6] [20.6] 45.7 [13.4] [20.0] 44.8 [13.1] [19.4] 43.8 [12.8] [18.6] 42.5 [12.5] [17.9] 41.1 [12.0] [17.0] 39.4 [11.6] [16.1] 37.6 [11.0] [15.2] 35.6 [10.4] [21.6] 60.8 [17.8] [21.2] 60.4 [17.7] [20.6] 59.8 [17.5] [20.0] 59.0 [17.3] [19.4] 58.0 [17.0] [18.7] 56.8 [16.6] [18.0] 55.4 [16.2] [17.1] 53.7 [15.7] [16.3] 51.9 [15.2] [15.3] 49.9 [14.6] [14.3] 47.6 [13.9] [21.2] 58.1 [17.0] [20.8] 57.7 [16.9] [20.3] 57.2 [16.7] [19.7] 56.4 [16.5] [19.1] 55.4 [16.2] [18.4] 54.3 [15.9] [17.6] 52.9 [15.5] [16.8] 51.3 [15.0] [16.0] 49.6 [14.5] [15.1] 47.6 [14.0] [14.1] 45.5 [13.3] [20.6] 54.0 [15.8] [20.2] 53.6 [15.7] [19.7] 53.1 [15.6] [19.1] 52.4 [15.3] [18.5] 51.5 [15.1] [17.9] 50.4 [14.8] [17.1] 49.1 [14.4] [16.4] 47.7 [14.0] [15.5] 46.1 [13.5] [14.6] 44.2 [13.0] [13.7] 42.2 [12.4] [20.8] 64.0 [18.7] [20.3] 63.6 [18.6] [19.8] 63.0 [18.5] [19.2] 62.2 [18.2] [18.6] 61.2 [17.9] [17.9] 60.0 [17.6] [17.1] 58.4 [17.1] [16.3] 55.6 [16.3] [15.4] 52.6 [15.4] [14.5] 49.5 [14.5] [13.5] 46.1 [13.5] [20.4] 61.1 [17.9] [20.0] 60.7 [17.8] [19.4] 60.2 [17.6] [18.9] 59.4 [17.4] [18.2] 58.4 [17.1] [17.6] 57.3 [16.8] [16.8] 55.9 [16.4] [16.0] 54.4 [15.9] [15.2] 51.7 [15.2] [14.2] 48.6 [14.2] [13.3] 45.2 [13.3] 7.7 NOTES: ➀ When the entering air dry bulb is other than 80 F [27 C], adjust the sensible capacity from the table by adding [1.10 x CFM x (1 DR) x (dbe 80)] [19.8] 56.8 [16.6] [19.4] 56.4 [16.5] [18.9] 55.9 [16.4] [18.3] 55.2 [16.2] [17.7] 54.3 [15.9] [17.1] 53.2 [15.6] [16.3] 51.9 [15.2] [15.6] 50.5 [14.8] [14.7] 48.9 [14.3] [13.8] 47.0 [13.8] [12.9] 44.0 [12.9] [19.9] 66.6 [19.5] [19.5] 66.2 [19.4] [18.9] 64.6 [18.9] [18.3] 62.6 [18.3] [17.7] 60.4 [17.7] [17.0] 58.0 [17.0] [16.3] 55.5 [16.3] [15.4] 52.7 [15.4] [14.6] 49.7 [14.6] [13.6] 46.5 [13.6] [12.6] 43.1 [12.6] [19.6] 63.6 [18.6] [19.1] 63.3 [18.5] [18.6] 62.7 [18.4] [18.0] 61.5 [18.0] [17.4] 59.3 [17.4] [16.7] 57.0 [16.7] [16.0] 54.5 [16.0] [15.2] 51.7 [15.2] [14.3] 48.8 [14.3] [13.4] 45.7 [13.4] [12.4] 42.3 [12.4] [19.0] 59.1 [17.3] [18.6] 58.8 [17.2] [18.1] 58.2 [17.1] [17.5] 57.5 [16.9] [16.9] 56.6 [16.6] [16.2] 55.4 [16.2] [15.5] 53.0 [15.5] [14.7] 50.3 [14.7] [13.9] 47.4 [13.9] [13.0] 44.4 [13.0] [12.1] 41.2 [12.1] Rely on Ruud.

11 Airflow Performance BELT-DRIVE AIRFLOW PERFORMANCE 6 TON [21.10 kw] MODEL Air Flow CFM [L/s] Capacity 6 Ton [21.10 kw] Voltage 208/ & Phase 0.1 [.02] 0.2 [.05] 0.3 [.07] 0.4 [.10] 0.5 [.12] 0.6 [.15] External Static Pressure Inches of Water [kpa] 0.7 [.17] 0.8 [.20] 0.9 [.22] RPM W RPM W RPM W RPM W RPM W RPM W RPM W RPM W RPM W RPM W RPM W RPM W RPM W RPM W RPM W 1800 [850] [897] [944] [991] [1038] [1085] [1133] [1180] [1227] [1274] [1321] [1369] [1416] NOTE: L-Drive left of bold line, M-Drive right of bold line. 1.0 [.25] 1.1 [.27] 1.2 [.30] 1.3 [.32] 1.4 [.35] 1.5 [.37] Drive Package L M Motor H.P. [w] 1-1/2 [1118.5] 1-1/2 [1118.5] Blower Sheave 6.4 Pitch Diameter 6.4 Pitch Diameter Motor Sheave Adjustable Pitch Diameter Adjustable Pitch Diameter Turns Open RPM Factory sheave settings are shown in bold print. COMPONENT AIR RESISTANCE Standard Indoor Airflow CFM [L/s] Component 2200 [944] 2400 [1133] 2600 [1227] 2800 [1321] 3200 [1510] 3400 [1605] Resistance Inches Water [kpa] Wet Coil Downflow R.S.I. Economizer R.A. Damper NOTES: 1. Performance shown with dry coil & standard 2" [50.8 mm] filters. 2. Standard lbs./cu. ft. 3. Motor efficiency = 80% 4. BHP = Watts x Motor Eff Add component resistance to duct static to determine E.S.P. as shown on charts. Rely on Ruud. 11

12 Electrical Data ELECTRICAL DATA RLKN SERIES Evaporator Fan Condenser Motor Compressor Motor Unit Information B073CL B073CM B073DL B073DM B073YL B073YM Unit Operating Voltage Range Volts 208/ / Phase Hz Minimum Circuit Ampacity Minimum Overcurrent Protection Device Size Maximum Overcurrent Protection Device Size No Volts 208/ / Phase RPM HP, Compressor Amps (RLA), Comp Amps (LRA), Comp No Volts 208/ / Phase HP 1/2 1/2 1/2 1/2 1/2 1/2 Amps (FLA, each) Amps (LRA, each) No Volts 208/ / Phase HP /2 1 1/2 Amps (FLA, each) Amps (LRA, each) Rely on Ruud.

13 Electric Heater Kits B073CL B073CM Model No. RLKN- RXJJ- Heater Kit Nominal kw No. of Sequence Steps 208/240 VOLT, THREE PHASE, 60 HZ, AUXILIARY ELECTRIC HEATER KITS CHARACTERISTICS AND APPLICATION Single Power Supply for Both Unit and Heater Kit Separate Power Supply for Both Unit and Heater Kit Heater Kit Air Conditioner Heater Kit Air Conditioner Rated Heater 208/240V Heater 208/240V Heater 208/240V Unit Min. Ckt. 240V Max. Over Current Protective Device Size Min. Ckt. Ampacity 208/240V Max. Fuse Size 208/240V Min. Circuit Ampacity 208/240V Max. Over Current Protective Device Size V No Heat 31/ / A06C 1 4.2/ / / / /17 15/20 31/ A10C 1 7.2/ / / / /29 25/30 31/ A15C / / / / /44 40/45 31/ A20C / / / / /58 50/60 31/ A24C 1 18/ / / / /73 70/80 31/ No Heat 31/ / A06C 1 4.2/ / / / /17 15/20 31/ A10C 1 7.2/ / / / /29 25/30 31/ A15C / / / / /44 40/45 31/ A20C / / / / /58 50/60 31/ A24C 1 18/ / / / /73 70/80 31/ B073DL B073DM Model No. RLKN- RXJJ- Heater Kit Nominal kw No. of Sequence Steps 480 VOLT, THREE PHASE, 60 HZ, AUXILIARY ELECTRIC HEATER KITS CHARACTERISTICS AND APPLICATION Single Power Supply for Both Unit and Heater Kit Separate Power Supply for Both Unit and Heater Kit Heater Kit Air Conditioner Heater Kit Air Conditioner Rated Heater 480V Heater 480V Heater 480V Unit Min. Ckt. 480V Max. Over Current Protective Device Size Min. Ckt. Ampacity 480V Max. Fuse Size 480V Min. Circuit Ampacity 480V Max. Over Current Protective Device Size 480V 480V No Heat A06D A10D A15D A20D A24D No Heat A06D A10D A15D A20D A24D *= For Canadian use only. Uses P fuses for inductive circuit. + = Field installed only. Rely on Ruud. 13

14 Electric Heater Kits B073YL Model No. RLKN- RXJJ- Heater Kit Nominal kw No. of Sequence Steps 600 VOLT, THREE PHASE, 60 HZ, AUXILIARY ELECTRIC HEATER KITS CHARACTERISTICS AND APPLICATION Single Power Supply for Both Unit and Heater Kit Separate Power Supply for Both Unit and Heater Kit Heater Kit Air Conditioner Heater Kit Air Conditioner Rated Heater 600V Heater 600V Heater 600V Unit Min. Ckt. 600V Max. Over Current Protective Device Size Min. Ckt. Ampacity 600V Max. Fuse Size 600V Min. Circuit Ampacity 600V Max. Over Current Protective Device Size 600V 600V No Heat A15Y A20Y A24Y No Heat A15Y B073YM A20Y A24Y *= For Canadian use only. Uses P fuses for inductive circuit. + = Field installed only. 14 Rely on Ruud.

15 Dimensional Data RLKN-B 6 TON [21.1 kw] MODEL BACK VIEW Rely on Ruud. 15

16 Dimensional Data RLKN-B 6 TON [21.1 kw] MODEL SIDE VIEW TOP VIEW 4 5 /8 [118 mm] 4 1 /2 [114 mm] 26 [660 mm] 2 5 /32 [55 mm] 2 3 /8 [60 mm] [114 mm] 13 1 /8 [333 mm] RETURN AIR SUPPLY AIR 20 [508 mm] 43 7 /32 [1098 mm] Illustration ST-A /8 [60 mm] 13 1 /8 [333 mm] /32 [1968 mm] 2 3 /8 [60 mm] FRONT VIEW Illustration ST-A Rely on Ruud.

17 Dimensional Data WEIGHTS Accessory Economizer with Single Enthalpy, Downflow/Sideflow Power Exhaust Fresh Air Damper (Manual) Fresh Air Damper (Motorized) Roof Curb 14" Roof Curb 24" Concentric Diffuser 18" Flush Concentric Diffuser 20" Flush Side Discharge Concentric Diffuser RXRN-FA60 Side Discharge Concentric Diffuser RXRN-FA65 Operating lbs [kg] 80 [36] 21 [10] 14 [6] 16 [7] 92 [42] 108 [49] 37 [17] 54 [24] 55 [25] 6 Ton [21.1 kw] Operating lbs [kg] 70 [32] 17 [8] 12 [5] 14 [6] 88 [40] 104 [47] 26 [12] 42 [19] 40 [18] CLEARANCES The following minimum clearances are recommended for proper unit performance and serviceability. Recommended Clearance in. [mm] Location 48 [1219] A - Front 18 [457] B - Condenser Coil *12 [305] C - Duct Side 36 [914] D - Evaporator End 60 [1524] E - Above *57" [1448 mm] With Economizer NOTE: Supply duct may be installed with 0 inch clearance to combustible materials, provided 1" [25.4 mm] minimum. Fiberglass insulation is applied either inside or on the outside of the duct. CENTER OF GRAVITY (C.G.) Capacity Tons [kw] A in. [mm] B in. [mm] 6 [21.1] 39 [991] 26 1 /8 [664] Capacity Tons [kw] Corner Weights by Percentage 6 [21.1] A B C D 23% 29% 21% 27% CLEARANCES 6 Ton [21.1 kw] Models Rely on Ruud. 17

18 Accessories ACCESSORY EQUIPMENT Accessory Description Model Application Accessory Model No. Factory Installed Roofcurb, 14" RLKN-B073 RXKG-CAD14 No Roofcurb, 24" RLKN-B073 RXKG-CAD24 No Roofcurb adapters RLKN-B073 RXRX-CCCE50 No Economizer, with single enthalpy RLKN-B073 AXRD-01RCCAM3 Yes Economizer, with smoke detector RLKN-B073 AXRD-01RCCBM3 Yes Dual enthalpy kit for economizer RLKN-B073 RXRX-AV02 No CO2 sensor RLKN-B073 RXRX-AR02 No Power exhaust (C, D, Y voltages) RLKN-B073 AXRX-BGF03 (C,D,Y) No Fresh air damper, manual RLKN-B073 AXRF-FCA1 No Fresh air damper, motorized RLKN-B073 AXRF-JHB1 No Rectangular-to-round 20" duct adapters for concentric diffuser RLKN-B073 RXMC-CC04 No Concentric diffuser 20", step type RLKN-B073 RXRN-FA65 No Concentric diffuser 20", flush type RLKN-B073 RXRN-FA75 No Louver kit, 3-sided RLKN-B073 AXRX-AAD01B Yes Compressor time delay RLKN-B073 RXMD-B04 No Low ambient control RLKN-B073 RXRZ-A04 Yes Convenience outlet (requires separate power supply) RLKN-B073 RXRX-AN02 Yes Freeze stat control RLKN-B073 RXRX-AM01 Yes *Voltage C = VAC-3PH-60HZ D = 460 VAC-3PH-60HZ Y = 575 VAC-3PH-60HZ 18 Rely on Ruud.

19 Accessories ROOFCURB ADAPTER Old Models OLD CURB MODEL ROOFCURB ADAPTER NEW MODEL COMMERCIAL PACKAGE UNIT (6 TON [21.1 kw]) RXRK-E50 RXRX-CCCE50 RLKN-B073 (-)RCF, (-)REF, (-)RGF131 & 201, RGF150 Rely on Ruud. 19

20 Accessories ROOFCURBS (Full Perimeter) n Ruud s new roofcurb design can be utilized on 3 through 7.5 ton [21.1 kw] models. n Two available heights (14" [356 mm] and 24" [610 mm]) for ALL models. n Quick assembly corners for simple and fast assembly. TYPICAL INSTALLATION n Opening provided in bottom pan to match the Thru the Curb electrical connection opening provided on the unit base pan. n 2" [51 mm] x 4" [102 mm] Nailer provided. n Insulating panels provided. n Sealing gasket (28" [711 mm]) provided with Roofcurb. n Packaged for easy field assembly. Roofcurb Model RXKG-CAD14 RXKG-CAD24 Height of Curb 14" [356 mm] 24" [610 mm] 20 Rely on Ruud.

21 Accessories ECONOMIZERS AXRD-01RCCAM3 3-6 Ton [ kw] Models AXRD-01RCCBM3 3-6 Ton [ kw] Models RXRX-AV Ton [ kw] Models RXRX-AR Ton [ kw] Models Single Enthalpy (with Barometric Relief) Single Enthalpy and Smoke Detector Dual Enthalpy Kit Optional CO 2 Sensor Features Honeywell JADE Digital Controls Available factory installed or field accessory Gear Driven Direct Drive Actuator Fully Modulating (0-100%) Low Leakage Dampers Horizontal or Downflow Applications Slip-In Design for Easy Installations Plug-In Polarized 12-pin Electrical Connections Pre-configuring No Field Adjustments Necessary Standard Barometric Relief Damper Provided Single Enthalpy with Dual Enthalpy upgrade kit CO2 Input Sensor Available (field installed) Economizer slips in complete for downflow or horizontal duct applications Field assembled hood ships with Economizer Field installed power exhaust available. Rely on Ruud. 21

22 Accessories INTEGRAL POWER EXHAUST FOR ECONOMIZER (FIELD INSTALLED ONLY) AXRX-BGF03 RLKN-B 6 Ton [21.1 kw] Model n For Honeywell Economizer n Downflow or horizontal applications n Requires separate volt 1 PH power supply with disconnect or requires separate 460V - 1 PH power supply with disconnect. n Adjustable switch on economizer, factory preset to energize power exhaust at 95% outside air position n Polarized plug connects power exhaust relay to economizer POWER EXHAUST KIT FOR AXRD-01CCAM3 & AXRD-01CCBM3 ECONOMIZERS Model No. No. of Fans Volts Phase Watts (ea.) High Speed CFM RPM FLA (ea.) LRA (ea.) AXRX-BGF03C 1 208/ AXRX-BGF03D AXRX-BGF03Y AXRX-BGF04C 1 208/ AXRX-BGF04D AXRX-BGF04Y CFM is at 0" w.c. external static pressure Unit includes 575 to 460 Volt step-down transformer FRESH AIR DAMPER RLKN-B 6 Ton [21.1 kw] Models AXRF-FCA1 (Manual) AXRF-JHB1 (Motorized) Shipping lbs [kg] 70 [32] Operating lbs [kg] 67 [30] I319.DGN FRESH AIR DAMPER 22 Rely on Ruud.

23 Accessories DUCT ADAPTERS (RLKN-B 6 TON [21.1 kw] MODELS) Rectangular to Round Transitions (Downflow) Accessory Model No. RXMC-CC04 Model Application Tons [kw] 6 [21.1] Size in. [mm] 20 [508] Round Rely on Ruud. 23

24 Accessories SIDE DISCHARGE CONCENTRIC DIFFUSER RXRN-FA65 (6 Ton [21.1 kw] Models) For Use With Duct Adapter (RXMC) DIMENSIONAL DATA Model No. A B C D E F G H I J K RXRN-FA /8" [1210 mm] 29 5 /8" [752 mm] 14 3 /8" [365 mm] 27 1 /2" [699 mm] 45 1 /2" [1156 mm] 22 1 /2" [572 mm] 11 1 /2" [292 mm] 13 3 /4" [349 mm] 45 1 /2" [1156 mm] 27 1 /2" [699 mm] 8 1 /8" [206 mm] Duct Size 20RD ENGINEERING DATA Model No. RXRN-FA65 CFM [L/s] Static Pressure Throw Feet 2600 [1227] [1321] [1416] [1510] [1605] Neck Vel. Jet Vel. Noise Level 24 Rely on Ruud.

25 Accessories FLUSH MOUNT CONCENTRIC DIFFUSER RXRN-FA75 (6 Ton [21.1 kw] Models) For Use With Duct Adapter (RXMC) DIMENSIONAL DATA Model No. A B C D E F G H RXRN-FA /8" [1210 mm] 29 5 /8" [752 mm] 16 5 /8" [422 mm] 27" [686 mm] 45 1 /2" [1156 mm] 22 1 /2" [572 mm] 11 1 /4" [286 mm] 13 1 /2" [343 mm] Duct Size 20RD ENGINEERING DATA Model No. RXRN-FA75 CFM [L/s] Static Pressure Throw Feet 2600 [1227] [1321] [1416] [1510] [1605] Neck Vel. Jet Vel. Noise Level Rely on Ruud. 25

26 Mechanical Specifications SAMPLE SPECIFICATIONS Unit shall be completely factory assembled and performance tested to provide the required cooling and heating functions suitable for outdoor installations. Unit shall be UL/cUL listed and rated in accordance to AHRI Standard 210. Cabinet Unit casing, base pan and framework shall be manufactured of galvanized sheet metal primed and finished with powder paint capable of withstanding a 1000-hour salt spray test per ASTM B 117. Unit interior cabinet surfaces shall be insulated with a minimum 1/2-inch thick foil faced insulation. Access panels shall be easily removable providing access to the blower, filter, heating compartment, and compressor/ control box. Unit base rails shall be provided with fork insertion slots and rigging holes. Condensate drain pan shall be of sloped design to conform to ASHRAE 62. Unit shall be supplied ready for vertical airflow and be easily convertible to horizontal airflow at or before installation. Compressor(s) Unit shall be provided with fully hermetic scroll compressor(s) with internally protected safety controls. Coils Aluminum Microchannel evaporator and condenser coils. Aluminum lanced fins thermally bonded to aluminum multi-port flat tube design. Leak tested using helium mass spectrometry. Condenser Fan A single direct drive propeller fan shall discharge air vertically upward. The fan motor shall be permanently lubricated and have built-in overload protection. Evaporator Blower A single, double inlet, centrifugal wheel shall rotate in permanently lubricated ball bearings. The wheel shall be made from steel with corrosion resistant finish and shall be statically and dynamically balanced. ACCESSORIES ROOF CURB Curb shall be full perimeter type, complying with the standards of the National Roofing Contractors Association. Design shall provide for drop-in of supply and return ducts prior to setting unit, and include an insulating panel for the rest of the curb area. Economizer Economizer shall be completely assembled for field installation. Unit shall include all controls and dampers including the baro metric relief damper. Manual Fresh Air Damper Damper shall consist of damper and rainhood which is manually preset to admit up to 35% of outside air for field installation. Motorized Fresh Air Damper Damper shall consist of motor, damper, and rainhood which can admit up to 35% of outside air for field installation. Electric Heat Kits Electric heat kits shall be available in a wide range of capacity with branch circuit fusing allowing single point wiring. Kits shall be UL/cUL approved. Each kit shall be offered as a field or factory installed option. Pressure Controls High and low pressure controls shall be included for field or factory installation. Low Ambient Control Low ambient control shall be provided to cycle the condenser fan in response to condensing pressure and allow operation to 0 degrees F. The option shall be field or factory installed. Louver Panel Kits Field or factory installed louver kits shall be provided for condenser coil protection against hail or flying debris. 26 Rely on Ruud.

27 Limited Warranty BEFORE PURCHASING THIS APPLIANCE, READ IMPORTANT ENERGY COST AND EFFICIENCY INFORMATION AVAILABLE FROM YOUR RETAILER. GENERAL TERMS OF LIMITED WARRANTY* Ruud will furnish a replacement for any part of this product which fails in normal use and service within the applicable periods stated, in accordance with the terms of the limited warranty. *For complete details of the Limited and Conditional Warranties, including applicable terms and conditions, contact your local contractor or the Manufacturer for a copy of the product warranty certificate. Compressor 3 Phase, Commercial Applications...Five (5) Years Parts 3 Phase, Commercial Applications...One (1) Year Rely on Ruud. 27

28 In keeping with its policy of continuous progress and product improvement, Ruud reserves the right to make changes without notice. Rely on Ruud. Ruud Heating, Cooling & Water Heating P.O. Box Fort Smith, Arkansas Ruud Canada 125 Edgeware Road, Unit 1 Brampton, Ontario L6Y 0P5 PRINTED IN U.S.A. 5/18 QG FORM NO. S REV. 1