RobLight FL User manual. Applies to: RobLight A/S Nordhavnsvej 1A DK Frederikshavn. Phone:

Transcription

1 Rev. 4.0 User manual FL 1050 A/S Nordhavnsvej 1A DK Frederikshavn Applies to: FL 1050 B K CRI FL 1050 B K CRI FL 1050 B K CRI FL 1050 B-2M 3000K CRI 95+

2 Page 2 Table of Contents Page 11 Troubleshooting Introduction... 3 Product overview/unboxing... 3 Technical data... 4 Accessories... 9 Application notes Maintenance, spare parts & repairs Troubleshooting Problem Trace the problem Solution No light Light switches on and off Check the power Check the temperature. Check the dimming Check the operating conditions of the light engine Check active cooling system. Connect the power cord properly/ Turn on the device Check it is installed according to the instructions. Unplug. Unplug the dimmer system from the driver. Turn on the power. Check it is installed according to the instructions. Remove dirt and dust from light engine. The center pages is the installation instructions and can be detached from the rest of the manual to be used by the installer of the system. Light output has diminished Check if the light has been dimmed via a dimmer? Check the operating conditions of the light engine Increase brightness to the normal level. If the light engine has been running at elevated temperatures for an extended time, a decrease in the output will be observed FOLLOW THE INSTALLATION INSTRUCTIONS TO ENSURE Safe operation Full functionality Stated expected lifetime Uninterrupted illumination If problems is not solved using this guide please contact Roblight A/S

3 Page 10 Application notes Page 3 Introduction The light generator is an electronic device so it will not work forever. The different components will have different factors influencing the practical lifetime. The most important factor for this system is the condition of the surrounding air (temperature and cleanliness). The data we have stated the expected lifetime of the key components at the temperatures the suppliers has performed their standardized tests and in clean environments. The light generator is designed to run at max. ambient, but the longest usable operation is achievable at lower temperatures. Although there is thermal protection built into this device; it is only a safety device and should not be used as a measurement device to test if the light generator is running at a tolerable surrounding temperature. Roblon FL1050 light generators are designed for use indoors/dry location with glass and PMMA fibre bundles. It can be use in all installations set-ups, including in closed compartments. Product overview/unboxing 1 FL 1050 Light generator 2 User manual KEEP COOL CLEAN AIR Maintenance, spare parts & repairs The effectiveness of active cooling device in greatly diminished if the cooling fins and the air intake is blocked or polluted with dust. This will reduce the expected lifetime of the product. The dust need to be removed by a fine brush, vacuum cleaning or light compressed air This light generator is not supposed to be otherwise serviced, if it is used as recommended. If the product isn t performing as specified, use the troubleshooting guide. If you need further assistance please contact our office. The warranty label should not be broken under ANY circumstances. If broken the warranty is terminated.! WARNING! Remove red cap before turning on!

4 Page 4 Page 9 Technical data Accessories General Light port Fibre type Material Dimensions (L x H x W) Dist. between driver and LE Weight (total) Safety Environmental Driver/electrical Driver Light source Applied LED Ø28 mm PMMA or Glass Aluminium, POM and other 248 x 73 x 86 mm 150 mm 1120 g Protection rating IP 20 Thermal protection Cooling CE, RoHS, WEEE Ambient temperature -10 C to 45 C Driver size (L x H x W) 125 x 23 x 79 Supply voltage (mains) Driver expected lifetime Dimmer systems applicable Total power consumption Cree LED expected lifetime T a = 25 C Typical CCT Yes, automatic resettable light sources cut off Ebmpapst cooling solution [7 db(a)] LED Driver constant current V 50/60 Hz h (@Ta = 3% failure level)) DALI, 1-10V, PWM and PUSH (mains) (DMX, Phage din Special req.) 42 W 3000 K or 4000 K, 3 SDMC Typical Ra (CRI 1-8 ) 93 (min. 90) (98 (min. 95) for ) Part name Description Ordrering CCT Filter A 500K CCT Filter A 900K CCT Filter A 1200K yellow green blue red Colour Wheel kit Twinkling Wheel kit Dimmer 1-10V (potentiometer) Adapter Ø28/Ø9 Will make the ligth warmer. Will not fade. No tools needed Will make the light warmer. Will not fade. No tools needed Will make the light warmer. Will not fade. No tools needed Yellow colour filter. Glass. Will not fade. No tools needed Green colour filter. Glass. Will not fade. No tools needed Blue colour filter. Glass. Will not fade. No tools needed Red colour filter. Glass. Will not fade. No tools needed. User attachable kit for make your fibres fibers light in sparkling colours. colors. User attachable kit to make your fibres fibers twinkle. Attach it to the driver and the product can be dimmed If you want to change the light port from Ø28 to Ø9 mm Need to order or get more information.

5 Page 8 Installing accessories Page 5 Attachment of harness The 1-10V dimmer potentiometer can be installed following this procedure. Remove lid and wire fasternes from the driver Place dimmer in 1-10V, brown wire in + Place fasternes and lid again a) Remove cap from the light port b) Insert the common end, fully in the light port c) Tighten the screw on the light port d) Ensure all installation and ventilation requirements are met (see page 5 & 6) e) Connect the supply cord to the mains. WARNING! Remove cap before turning on. Network line Wire from Dimmer 1-10V Potentiometer Wire from Light Generator Surface mounting Attach to surface using two screws (not supplied) in the baseplate holes Can be used as drilling template Always unplug, before working with the driver

6 Page 6 Vertical mounting Page 7 Installing adjacent light generators This light generator should not be mounted with light port up. At high ambient temperature the operational lifetime of the internal components will be reduced. Recommendation: Minimum 10 cm distance between adjacent light generators, to ensure enough free cooling air. If multiple rows. Use offset to avoid vertical rows. Minimal free distance between rows 20 cm. T max. has to be observed for all light generators. MAX. AMBIENT TEMPERATURE 45 C. Closed compartments MAX. AMBIENT TEMPERATURE 45 C. Recommendations: Enough space to allow natural heat transmission through surfaces. Surfaces may not be insulated. Minimum distance light generator to any enclosing surface 10 cm (excluded mounting surface). Air volume per light generator minimum 0.03 m³. Ventilation holes per light generator with min. 20 cm² air inlet and min. 20 cm² air outlet. Inlet and outlet ventilation holes opposite each other. Keep free from dust and polluted air. Controlling/measuring the temperature Ambient temperature: Max. 45 C. Measured 50 mm from the light engine and on a vertical plane at the same height as the center of the light engine. All temperatures to be measured when the installation has been running for at least 2 hours continuously.