BLADE-AL(DL)-TL1-EN. install TYPE SELECTiOn. YeAR. Vibe STD key AT/MT. xb STD key (40-bit) AT/MT

Transcription

1 Automotive Data Solutions Inc. INSTALL UIDE BLADE-AL(DL-TL-EN TL Available for : ADS-BLADE AL Rev. Date: June 0, 0 Doc. No.: ##08## Version FRançaise disponible en ligne au please visit for complete product details The brand names and logos found in this guide are property of their respective owners. Automotive Data Solutions Inc. 0! NOTICE: The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. This guide has been written for properly trained technicians; a certain level of skill & knowledge is therefore assumed. Please review the Installation uide carefully before beginning any work.

2 BLADE-AL(DL-TL-EN Page of 000 Doc. No.: ##08## install TYPE SELECTiOn FeUReS BRAKe PeDAl STUS output e-brake output DooR STUS output TRUnK STUS output HooD STUS output* ToYoTA Camry (0-bit /MT 0- Camry /MT 0- Camry Hybrid /MT 0- Corolla (0-bit /MT 09-0 Corolla 09- Corolla MT 09- Highlander (0-bit 08-0 Highlander 08- Highlander Hybrid 08- Matrix (0-bit /MT 09-0 Rav (0-bit 0-0 Rav 09- Sequoia (0-bit 08-0 Tundra (0-bit Yaris (0-bit /MT * Available only if vehicle is equipped with factory hood switch. install TYPe TRUnK/HCH ReleASe xd (0-bit /MT DooR UnloCK xb (0-bit /MT DooR lock DA immobilizer BYPASS 09-0 DiSARM oem AlARM YeAR Vibe /MT ARM oem AlARM MoDel PUSH To START CTRl MAKe 0- SCion PonTiAC ES0 TAile WinDoW ReleASe Keyless and smartkey systems will remain functional during remote start. lexus I TACHoMeTeR output NOTE Automotive Data Solutions Inc. 0

3 BLADE-AL(DL-TL-EN Page of Doc. No.: ##08## 000 COMPOnEnT LOCOr A B C Automotive Data Solutions Inc. 0

4 BLADE-AL(DL-TL-EN Page of Doc. No.: ##08## 000 name TYPe PoSiTion PolARiTY MoDUle locion CoMPonenT locor 0 Red 0 Brown E Beige 0 LtBlue E8 8 Brown 0 Ltreen 0 reen 0 Pink 09-0 E8 8 Brown Corolla TMMC 09-0 /MT Corolla NUMMI /MT ToYoTA Highlander Matrix /MT Rav Sequoia Tundra Yaris /MT DeSCRiPTion Camry /MT YeAR MoDel MAKe TYPE - wire CrOSS reference CHArT - OF 0 Ltreen 0 LtBlue 0 Red D 8 LtBlue Blue 0 Beige 0 LtBlue E 8 Brown Ltreen 0 reen 0 Pink E Brown 0 0 Blue 0 Ltreen H 8 Orange Purple 0 Blue 0 Ltreen J0 8 Ltray Purple 0 Purple 0 reen Purple Automotive Data Solutions Inc. 0

5 BLADE-AL(DL-TL-EN Page of Doc. No.: ##08## 000 SCion xb /MT xd /MT name TYPe PoSiTion PolARiTY MoDUle locion CoMPonenT locor YeAR MoDel Vibe /MT DeSCRiPTion PonTiAC MAKe TYPE - wire CrOSS reference CHArT - OF Beige LtBlue E 8 Brown 09-0 Beige LtBlue C Ltreen Ltreen Purple reen 08-0 Purple Automotive Data Solutions Inc. 0

6 BLADE-AL(DL-TL-EN Page of 000 Doc. No.: ##08## TYPE - wiring DIARAM NOTE CONNECTOR AND PINOUT MAY VARY. PLEASE REFER TO CHART. CONNECTOR PARKIN LIHT SWITCH PA RK IN LI HT ( REMOTE STARTER DE CO CT TX STANDARD (IN, ACC, START REMOTE STARTER CONNECTIONS TO VEHICLE ARE REQUIRED PARKIN LIHT OUTPUT WHITE/RED 0 0 WHITE/BLACK WHITE 09 9 PINK/BLACK 08 8 PINK 0 BLACK BROWN/RED 0 BROWN/YELLOW ORANE/BLACK 0 ORANE/WHITE ORANE 0 0 BLUE/YELLOW 0 YELLOW RAY/RED 0 RAY/YELLOW WITHOUT OEM HOOD SWITCH ONLY N H BLUE/RED REEN/RED WHITE/BLACK (NC WHITE/RED (NC WHITE (NC YELLOW (NC BROWN/RED - NH BROWN/YELLOW -NL ORANE/BLACK - ROUND INPUT ORANE/WHITE (NC ORANE (NC PINK/BLACK (NC PINK (NC BLUE/RED (NC BLUE/YELLOW (NC REEN/RED - CODE RAY/RED - RAY/YELLOW (NC BLACK (NC NL *BLADE CONNECTOR EXACT PIN-OUT Automotive Data Solutions Inc. 0

7 BLADE-AL(DL-TL-EN Page of Doc. No.: ##08## 000 TYPe PoSiTion PolARiTY MoDUle locion CoMPonenT locor 09- Rav 09- name Corolla NUMMI 09- DeSCRiPTion ToYoTA Corolla TMMC YeAR MoDel MAKe TYPE - wire CrOSS reference CHArT - OF F 8 pin Yellow E 9 pin pin E8 8 Brown F 8 pin Red E 9 pin pin E8 8 Brown F 8 pin Yellow E 9 pin Red pin E 8 Brown Ltreen Ltreen Automotive Data Solutions Inc. 0

8 BLADE-AL(DL-TL-EN Page 8 of Doc. No.: ##08## 000 TYPE - wiring DIARAM MAIN BODY FRONT SIDE BACK SIDE NOTE CONNECTOR AND PINOUT MAY VARY. PLEASE REFER TO CHART PA RK IN LI HT ( CONNECTOR PARKIN LIHT SWITCH REMOTE STARTER ON TI NI I (+ WARNIN: DO NOT CONNECT ANY OTHER ACCESSORY,INITION OR START WIRE FROM THE REMOTE STARTER TO THE VEHICLE. THE INTERFACE MODULE IS HANDLIN THE REQUIRED VEHICLE POWER AND START SEQUENCE FROM THE PUSH TO START BUTTON CIRCUIT. DIODE N00 (+ INITION INPUT SW ST PARKIN LIHT OUTPUT H N L N *BLADE CONNECTOR EXACT PIN-OUT WHITE/RED 0 0 WHITE/BLACK WHITE 09 9 PINK/BLACK 08 8 PINK 0 BLACK BROWN/RED 0 BROWN/YELLOW ORANE/BLACK 0 ORANE/WHITE ORANE 0 BLUE/RED 0 BLUE/YELLOW REEN/RED 0 YELLOW RAY/RED 0 RAY/YELLOW WHITE/BLACK - OUTPUT WHITE/RED (NC WHITE - INITION INPUT YELLOW (NC BROWN/RED - NH BROWN/YELLOW - NL ORANE/BLACK - ROUND INPUT ORANE/WHITE (NC ORANE (NC PINK/BLACK (NC PINK (NC BLUE/RED - ROUND INPUT BLUE/YELLOW - OUTPUT REEN/RED (NC RAY/RED (NC RAY/YELLOW (NC BLACK (NC WITHOUT OEM HOOD SWITCH ONLY IMPORTANT: - NO TAKEOVER AVAILABLE. UPON OPENIN VEHICLE DOOR ENINE WILL SHUTDOWN. - ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE. ENINE START STOP PT S (- CONNECTIONS ARE REQUIRED ONLY IF IDLE MODE IS DESIRED Automotive Data Solutions Inc. 0

9 BLADE-AL(DL-TL-EN Page 9 of Doc. No.: ##08## 000 PolARiTY MoDUle locion CoMPonenT locor 08- Highlander Hybrid 08- PoSiTion Highlander TYPe 0-0- ToYoTA Camry Hybrid /MT 0- name Camry /MT YeAR MoDel ES0 DeSCRiPTion lexus MAKe TYPE - wire CrOSS reference CHArT - OF I 0 pin 0 E 0 pin 0 Red pin 0 Blue E 8 0 Ltreen Pink I 0 pin 0 Brown E9 0 pin 0 ray pin 0 Blue E 8 0 I 0 pin 0 Brown E9 0 pin 0 ray pin 0 Blue E 8 0 I 0 pin 0 D0 0 pin 0 Pink pin 0 Pink D 8 LtBlue 0 Blue I 0 pin 0 D0 0 pin 0 Yellow pin 0 Pink D 8 LtBlue 0 Automotive Data Solutions Inc. 0

10 BLADE-AL(DL-TL-EN Page 0 of 000 Doc. No.: ##08## TYPE - wiring DIARAM MAIN BODY BACK SIDE NOTE CONNECTOR AND PINOUT MAY VARY. PLEASE REFER TO CHART PA RK IN (+ SW LI ST HT ( CONNECTOR PARKIN LIHT SWITCH TI NI I REMOTE STARTER (+ PARKIN LIHT OUTPUT ON WARNIN: DO NOT CONNECT ANY OTHER ACCESSORY,INITION OR START WIRE FROM THE REMOTE STARTER TO THE VEHICLE. THE INTERFACE MODULE IS HANDLIN THE REQUIRED VEHICLE POWER AND START SEQUENCE FROM THE PUSH TO START BUTTON CIRCUIT. DIODE INITION INPUT N H N L N *BLADE CONNECTOR EXACT PIN-OUT WHITE/RED 0 0 WHITE/BLACK WHITE 09 9 PINK/BLACK 08 8 PINK 0 BLACK BROWN/RED 0 BROWN/YELLOW ORANE/BLACK 0 ORANE/WHITE ORANE 0 BLUE/RED 0 BLUE/YELLOW REEN/RED 0 YELLOW RAY/RED 0 RAY/YELLOW WHITE/BLACK - OUTPUT WHITE/RED (NC WHITE - INITION INPUT YELLOW (NC BROWN/RED - NH BROWN/YELLOW - NL ORANE/BLACK - ROUND INPUT ORANE/WHITE (NC ORANE (NC PINK/BLACK (NC PINK (NC BLUE/RED - ROUND INPUT BLUE/YELLOW - OUTPUT REEN/RED (NC REEN/YELLOW (NC RAY/RED (NC RAY/YELLOW (NC WITHOUT OEM HOOD SWITCH ONLY IMPORTANT: - NO TAKEOVER AVAILABLE. UPON OPENIN VEHICLE DOOR ENINE WILL SHUTDOWN. - ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE. ENINE START STOP PT S (- CONNECTIONS ARE REQUIRED ONLY IF IDLE MODE IS DESIRED Automotive Data Solutions Inc. 0

11 BLADE-AL(DL-TL-EN Page of Doc. No.: ##08## 000 MoDUle locion CoMPonenT locor F 8 pin Yellow A E 9 pin A E8 pin B E8 8 Brown Clutch A pin Clutch Switch C Clutch A pin Ltreen Clutch Switch C F 8 pin Red A E 9 pin A E8 pin B E8 8 Brown Clutch A pin Clutch Switch C Clutch A pin Ltreen Clutch Switch C name PolARiTY DeSCRiPTion 09- PoSiTion Corolla NUMMI MT TYPe 09- ToYoTA Corolla TMMC MT YeAR MoDel MAKe TYPE - wire CrOSS reference CHArT - OF Ltreen Ltreen Automotive Data Solutions Inc. 0

12 BLADE-AL(DL-TL-EN Page of Doc. No.: ##08## 000 TYPE - wiring DIARAM MAIN BODY FRONT SIDE BACK SIDE NOTE CONNECTOR AND PINOUT MAY VARY. PLEASE REFER TO CHART PA RK IN LI HT ( CONNECTOR PARKIN LIHT SWITCH REMOTE STARTER ON TI NI I (+ WARNIN: DO NOT CONNECT ANY OTHER ACCESSORY,INITION OR START WIRE FROM THE REMOTE STARTER TO THE VEHICLE. THE INTERFACE MODULE IS HANDLIN THE REQUIRED VEHICLE POWER AND START SEQUENCE FROM THE PUSH TO START BUTTON CIRCUIT. SW ST (+ PARKIN LIHT OUTPUT ROUND WHEN RUNNIN OUTPUT DIODE INITION INPUT N H N L N *BLADE CONNECTOR EXACT PIN-OUT WHITE/RED 0 0 WHITE/BLACK WHITE 09 9 PINK/BLACK 08 8 PINK 0 BLACK BROWN/RED 0 BROWN/YELLOW ORANE/BLACK 0 ORANE/WHITE ORANE 0 BLUE/RED 0 BLUE/YELLOW REEN/RED 0 YELLOW RAY/RED 0 RAY/YELLOW WHITE/BLACK - OUTPUT WHITE/RED (NC WHITE - INITION INPUT YELLOW (NC BROWN/RED - NH BROWN/YELLOW - NL ORANE/BLACK - ROUND INPUT ORANE/WHITE (NC ORANE (NC PINK/BLACK (NC PINK (NC BLUE/RED - ROUND INPUT BLUE/YELLOW - OUTPUT REEN/RED (NC RAY/RED - ROUND INPUT RAY/YELLOW (NC BLACK (NC WITHOUT OEM HOOD SWITCH ONLY A - CLUTCH SWITCH 8 8 8A 8 0 IMPORTANT: - NO TAKEOVER AVAILABLE. UPON OPENIN VEHICLE DOOR ENINE WILL SHUTDOWN. - ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE. ENINE START STOP PT S (- CH UT CH UT CL CL V Automotive Data Solutions Inc. 0

13 BLADE-AL(DL-TL-EN Page of Doc. No.: ##08## 000 rtridge installion Slide cartridge into unit. Notice button under LED. Ready for Module Programming Procedure. TYPE - MODULE PrOgrAMMing PrOCEDUrE NOTE I Insert key into ignition. LED will flash BLUE and RED. 8 Wait, LED will turn solid BLUE then will turn OFF. Turn key to OFF position. 9 Remove key. Remove key. 0 Module Programming Procedure completed. Between each step, LED will turn solid RED, this is the default standby mode. Insert key into ignition. Turn key to ON position. ON x OFF (If vehicle is not equipped with immobilizer, press module programming button. LED will flash BLUE once [x]. Automotive Data Solutions Inc. 0

14 BLADE-AL(DL-TL-EN Page of Doc. No.: ##08## 000 TYPE, & - MODULE PrOgrAMMing PrOCEDUrE NOTE I Between each step, LED will turn solid RED, this is the default standby mode. Æ ENINE START STOP x Push start button twice [x] to ON position. Æ ENINE START STOP x Push start button once [x] to OFF position. Module Programming Procedure completed. Wait, LED will turn solid BLUE then will turn OFF. Automotive Data Solutions Inc. 0

15 BLADE-AL XX-XX PENT - PAE X-X BLADE-AL(DL-TL-EN Page of Doc. No.: ##08## 000 identify VEHiCLE notice YEAr Locate the Vehicle Identification Number (VIN and identify the 0th character. Æ AYNTAL8DR0X Match the VIN s 0th character to its corresponding year. l > 990 S > 99 Y > 000 > 00 A > 00 M > 99 T > 99 > 00 > 00 B > 0 n > 99 V > 99 > 00 > 00 C > 0 P > 99 W > 998 > 00 8 > 008 D > 0 R > 99 X > 999 > 00 9 > 009 e > 0 MODULE DiAgnOSTiCS led STUS DiAnoSTiCS DURin PRoRAMMin DURin ReMoTe START WiTH inition off Flashing RED Missing/wrong information from firmware or vehicle Incorrectly programmed Incorrectly programmed or connected Solid RED Waiting for more vehicle information Incorrectly programmed Not programmed waiting for more vehicle information Flashing BLUE Additional steps required to complete programming Correctly programmed and operational False ground when running status from remote starter Solid BLUE then OFF Correctly programmed Reset in progress Reset in progress OFF No activity or already programmed Invalid ground when running status from remote starter At rest and ready for a remote start sequence FACTOrY reset PrOCEDUrE DISCONNECT cartridge from remote starter. PRESS AND HOLD programming button while re-connecting cartridge to remote starter. LED will flash red. Immediately RELEASE programming button. LED will turn solid red for seconds. RESET COMPLETED. RECONNECT all connectors. Repeat programming procedure.! Failure to follow procedure may result with a DTC or a CHECK ENINE error message. This product is protected by one or more of the following patents: U.S. LETTErS PEnT no.,9,;,0,0;,,00;,9,;,,;,9,;,,8;,9,;,9,;,9,9;,,88;,,88;,,;,8,89;,9,0;,00,0;,0,8;,0,;,0,;,08,;,0,80;,0,9;,,08;,9,9;,8,9;,89,;,0,9; nadian PEnT no.,0,8;,,0;,,0;,,99;,,0;,,0;,,08;,,0;,0,89;,,90;,,9;,,8; EUrOPEAn PEnT no.,0,8; DE 980-9T; U.S. 000; 00098; 00098; 00008; ; ; EP00; 808; 80; Automotive Data Solutions Inc. 0