Automotive Data Solutions Inc.

Transcription

1 Automotive Data Solutions Inc. INSTALL GUIDE BLADE-AL(TB)-TL TL Available for : BLADE-AL Rev. Date: November, 009 Doc. No.: ##848## Version FRançaise disponible en ligne au please visit for complete product details NOTICE: The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. This guide has been written for properly trained technicians; a certain level of skill & knowledge is therefore assumed. Please!review the Installation Guide carefully before beginning any work.

2 Page of BLADE-AL(TB)-TL Doc. No.: ##848## VEhIcLE compatibility chart. DETERMINE INSTALL TYPE Refer to chart below legend / - Type may vary by vehicule equipment level. /3 - Type may be standard key or push to start. NC - Not covered warning Please advise that the install type numbers have changed since the last revision of this install guide. notes Type 3 install provides simulated tach output for hybrid vehicles. A hybrid vehicle might be running without its engine being running. To determine whether a hybrid vehicle is running or not, look at the instrument cluster, radio and heating system. Push to start vehicles have a maximum take over time of 45 seconds: for security reasons, during the remote starter runtime, the driver must press the unlock button of the remote starter fob to trigger a 45 seconds time window which will permit him/her to step into the vehicle and press the brake pedal to complete take over. install type make model Runner Avalon /3 /3 /3 /3 /3 camry / / /3 /3 /3 camry hybrid corolla /3 fj cruiser hiace highlander /3 /3 highlander hybrid hilux Land cruiser 3 NC toyota Matrix MR spyder Prius RAV4 /3 sequoia sienna solara / / tacoma tundra Venza (standard key only) Yaris Es 300 Es 330 Es NC Gs Gs NC Gs 400 Gs Gs 450 hybrid 3 3 NC Gs NC GX 470 Is NC Is 300 Is NC LEXUs Is-f 3 NC Ls 400 Ls 430 / / / Ls NC Ls 600 hybrid 3 NC LX 470 LX 570 NC NC RX 300 RX 330 RX 350 RX 400 hybrid sc 300 sc 400 sc 430 PoNtIAc Vibe scion tc. PROCEED WITH INSTALLATION See applicable wiring diagram

3 Page 3 of BLADE-AL(TB)-TL Doc. No.: ##848## KNoWLEDGE BAsE REGARDING THE TXCT WIRE IMPRoVED INstALL types,3,4 and 5 WIthoUt cutting the txct WIRE The new installation types without cutting the TXCT wire are a result of long term engineering researches, during the researches, it s been possible for our engineers to MAP the entire encryption for every vehicles covered by the TL Firmware. The MAP can now be used to learn the module without the need to send multiple challenges to the immobilizer receiver located at the key cylinder. During your install a simple connection to the TXCT wire will be made without interrupting cutting or interrupting it. During the learning process the module will automatically refer to the MAP. The most popular vehicles are listed first and the MAP refers to the less popular at the end ADVANcED DIAGNostIc The Firmware is monitoring the entire module learning process and records every steps in its EEPROM! As soon the module is connected to the vehicle it starts monitoring and recording all its I/O s (same as an airplane black box). The information can be extracted from the module and sent to your technical support team for advanced debugging at any required time. The information recorded is: Install Type Detects and registers Key Code Encryption Detects 80 Bits encryption keys (not supported) Records MAP reference Records Key Code Encryption Detects, records key collisions during remote start Offers a safety protection on Ground When Running Status Monitors RS3 communications Detects if the Module key code sent to vehicle was validated or rejected Filters and detects spikes on the ignition wire Protected memory buffer for module key code recovery even after module is re-flashed and a factory reset is been performed. TXCT/CODE inversion detection and protection Records Installation mode, firmware, hardware informations Protection enabled to learn the vehicle even if the immobilizer is in password mode the ADVANtAGEs: The TL solution is the safest and most reliable solution available in the field for the Toyota and Lexus vehicles. The MAP system is an exclusive improvement to protect the vehicle Immobilizer module during programming. With the use of this module, you will definitely secure your remote starter install with the best and safest known solution available in the market. older firmware: Call your technical support if you need access to an older firmware. - Firmware connecting to the IMI & IMO wires - Firmware cutting the TXCT wire upon programming.

4 Page 4 of BLADE-AL(TB)-TL Doc. No.: ##848## type WIRING DIAGRAM and wiring cross-reference chart STATUS (-) KEYSENSE (-) EXACT CONNECTOR PIN-OUT WHITE/RED 0 0 WHITE/BLACK WHITE 09 9 PINK/BLACK 08 8 PINK 07 7 BLACK BROWN/RED 06 6 BROWN/YELLOW ORANGE/BLACK 05 5 ORANGE/WHITE ORANGE 04 4 BLUE/RED GREEN/RED BLUE/YELLOW YELLOW GREY/RED 0 GREY/YELLOW WHITE/BLACK - RXCL KEY SIDE WHITE/RED - RXCK CAR SIDE WHITE (NC) YELLOW (NC) BROWN/RED (NC) BROWN/YELLOW (NC) ORANGE/BLACK (NC) ORANGE/WHITE (NC) ORANGE - AMP PINK/BLACK - CODE KEY SIDE PINK - CODE ECM SIDE BLUE/RED - TXCT BLUE/YELLOW (NC) GREEN/RED - DATA GRAY/RED - RXCK CAR SIDE GRAY/YELLOW (NC) BLACK (NC) CONNECTIONS MAY VARY ACCORDING TO VEHICLE. REFER TO CHART FOR CONNECTION DETAILS TO IMMOBILIZER RXCK AMP CODE TXCT model year pin amp pin code pin rxck pin txct pin ground (-) key sense conn. 4Runner White/Blue Gray/Red 3 Red/Black 4 Pink/Black 5 Brown Yellow/Red A Avalon Light Green Black/Red 3 Yellow 4 Green 5 White/Black Red/Yellow A Avalon Black/White Pink/Green 3 Blue/Orange 4 Blue/Yellow 5 White/Black Red/White A camry Black/Yellow Green/White 3 Red/Blue 4 Blue/Yellow 5 White/Black Blue/Black A camry (4cyl) Black/Red 4 Green/White 3 Red/Blue 5 Blue/Yellow 7 White/Black Blue B camry (6cyl) Black/Red 4 Green/White 3 Red/Blue 5 Blue/Yellow 7 White/Black Blue B Es Black/Yellow Green/White 3 Red/Blue 4 Blue/Yellow 5 White/Black Blue/Black A Es Black/Red 4 Green/White 3 Red/Blue 5 Blue/Yellow 7 White/Black Blue B Gs Black/Red Green/Black 3 Black/White 4 Blue/Red 5 White/Black Yellow E Gs Black/Red Green/Black 3 Black/White 4 Blue/Red 5 White/Black Yellow A Gs Black/Red Green/Black 3 Black/White 4 Blue/Red 5 White/Black Yellow E Gs Black/Red Green/Black 3 Black/White 4 Blue/Red 5 White/Black Yellow A highlander White 4 Gray/Blue 3 Pink 5 Gray 7 White/Black Blue B Is Black/Red Green 3 Purple 4 Pink 5 White/Black Black/Yellow A Is Black/Red Green/Black 3 Purple 4 Pink/Black 5 White/Black Black/Yellow A Land cruiser Black/Yellow Blue/Black 3 Purple/Green 4 Red/Yellow 5 White/Black Red/Black E Ls White Red/White 3 Red/Black 4 Red 5 White/Black Yellow A Ls Orange 4 Red/White 3 White/Red 5 Light-Blue/Black 7 Violet Lt Green/Black B Ls 430 (smartkey) Red 4 Orange 3 Light Blue 5 Yellow/Black 7 Violet Lt Green/Black B LX Black/Yellow Blue/Black 3 Purple/Green 4 Red/Yellow 5 White/Black Red/White E MR spyder Black Blue/Yellow 4 Yellow Blue/Black 3 White/Black Yellow/Red C RAV Black/Red Yellow/Green 4 Yellow Yellow/Black 3 White/Black Blue/Red C RX Blue/White Purple 3 Black 4 Gray 5 White/Black Blue A RX Blue/White Purple 3 Pink 4 Gray 5 White/Black Blue A RX Black/Red Purple 3 Pink 4 Gray 5 White/Black Blue A sc Black/Red Black/Orange 3 Blue 4 Green/Orange 5 White/Green Yellow A sc Black/Red Black/Orange 3 Blue 4 Green/Orange 5 White/Green Yellow A sc Yellow Violet/White 3 Red 4 Green 5 Violet Light Green/Black A sequoia 00-0 Black/Red 4 Red/Yellow 5 Light Green 6 Yellow/Green Orange Yellow/Green D sequoia Gray/Black 4 Red/Yellow 5 Light Green 6 Yellow/Green Gray/Light Blue Yellow/Green D sienna Black/Red Brown/White 3 Brown/Red 4 Brown/Yellow 5 White/Black Blue/Black A solara Red Green/White 3 Red/Blue 4 Blue/Yellow 5 White/Black Blue/Black A tundra s. cab 006 Red 3 Green 4 Blue/Red 5 Gray Pink Pink/Black D tundra D. cab 006 White 4 Green 5 Red 6 Black Gray Yellow/Green D connector type: connector is located at immobilizer near key barrel or 8 inches lower on the immobilizer harness. a B d E c

5 Page 5 of BLADE-AL(TB)-TL Doc. No.: ##848## type WIRING DIAGRAM AND WIRING CROSS-REFERENCE CHART EXACT CONNECTOR PIN-OUT KEYSENSE (-) WHITE/RED WHITE PINK/BLACK BROWN/RED ORANGE/BLACK ORANGE BLUE/RED GREEN/RED GREY/RED WHITE/BLACK PINK BLACK BROWN/YELLOW ORANGE/WHITE BLUE/YELLOW YELLOW GREY/YELLOW WHITE/BLACK - KEYSENSE (-) WHITE/RED (NC) WHITE - GROUND YELLOW(NC) BROWN/RED (NC) BROWN/YELLOW (NC) ORANGE/BLACK (NC) ORANGE/WHITE (NC) ORANGE (NC) PINK/BLACK (NC) PINK (NC) BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED - CODE GRAY/RED - TXCT GRAY/YELLOW (NC) BLACK (NC) CODE TXCT model years pin code pin txct key sense 4Runner Pink/Green 5 Light Green/Red Green/Yellow Avalon Light/Green 5 Brown Black camry Green/White 5 Blue/Yellow Blue camry Brown 5 Red Blue corolla Blue 5 Green Blue/Black corolla (Japan) Light Blue 5 Beige Light Blue corolla (canada) Pink 5 Green Light Blue fj cruiser Pink/Green 5 Light Green/Red Green/Yellow hiace Blue 5 Yellow Yellow/Black highlander Gray 5 White Green highlander Red 5 Light Blue Light Blue hilux Light Blue/Yellow 5 Light Blue/Black Green/Yellow Land cruiser Blue/Black 5 Violet/Green Red/Black Matrix Blue 5 Green Blue/Black Matrix Light Blue 5 Beige Blue RAV Blue/Red 5 Pink Blue/Red RAV Pink 5 Green Blue sequoia Light Green 5 Blue Gray sienna Yellow 5 Yellow/Red Blue/Black solara (convertible) Green/White 5 Blue/Yellow Blue solara (coupe) Yellow 5 Yellow/Red Blue tacoma Pink/Green 5 Light Green/Red Green/Black tundra Light Green 5 Blue Gray Venza Light Green 5 Brown Brown Yaris Green 5 Violet Yellow Es Green/White 5 Blue/Yellow Blue GX Yellow 5 Yellow/Black Green/Yellow Ls Red/White 5 Blue/Black Light Green/Black LX Blue/Black 5 Violet/Green Red/Black RX Light Green 5 Brown Black RX Light Green 5 Brown Black Vibe Blue 5 Green Blue/Black Vibe Light Blue 5 Beige Blue tc Yellow 5 Red Black

6 Page 6 of BLADE-AL(TB)-TL Doc. No.: ##848## type 3 WIRING DIAGRAM AND WIRING CROSS-REFERENCE CHART NOTE: FACTORY KEYFOB WILL NOT FUNCTION WHEN REMOTE STARTER IS ENGAGED. FOR AFTERMARKET KEYFOB FUNCTIONALITY, HARDWIRE REMOTE STARTER DOORLOCK AND ALARM OUTPUTS. REQUIRED: x RELAY X DIODE WARNING IGNITION IS USED ONLY AS AN INPUT TO THE REMOTE STARTER, NOT AN OUTPUT TO THE VEHICLE. THE DIODE CATHODE NEEDS TO BE FACING THE REMOTE STARTER BRAKE LAMP 87A 86 BRAKE SW V A B BRAKE INPUT (+) IGNITION (+) WARNING DO NOT CONNECT ANY OTHER ACCESSORY, IGNITION OR START WIRE FROM THE REMOTE STARTER TO THE VEHICLE. THE INTERFACE MODULE IS HANDLING THE REQUIRED VEHICLE POWERS AND START SEQUENCE FROM THE PUSH TO START BUTTON CIRCUIT. IGNITION AT BRAKE PEDAL 3 4 ENGINE START STOP EXACT CONNECTOR PIN-OUT WHITE/RED 0 0 WHITE/BLACK WHITE 09 9 PINK/BLACK 08 8 PINK 07 7 BLACK BROWN/RED 06 6 BROWN/YELLOW ORANGE/BLACK 05 5 ORANGE/WHITE ORANGE 04 4 BLUE/RED GREEN/RED BLUE/YELLOW YELLOW GREY/RED 0 GREY/YELLOW WHITE/BLACK WHITE/RED (NC) WHITE - GROUND YELLOW (NC) BROWN/RED (NC) BROWN/YELLOW (NC) ORANGE/BLACK (NC) ORANGE/WHITE (NC) ORANGE (NC) PINK/BLACK (NC) PINK (NC) BLUE/RED (NC) BLUE/YELLOW - PUSH GREEN/RED - CODE GRAY/RED - TXCT GRAY/YELLOW (NC) BLACK (NC) TXCT CODE PUSH (-) model years pin code pin txct pin push pin ignition pin v (BrakE) pin BrakE Avalon (smart key) White 9 Gray 7 Blue A3 Brown A Black A White camry hybrid White 9 Gray 7 Blue A3 Black A Black A White camry (smart key) White 9 Gray 7 Blue A3 Black A Black A Blue corolla (smart key) Green 9 Light Blue 7 White A3 Black A White A Blue highlander (smart key) Gray 9 Orange 7 Pink A3 White A Violet A Blue highlander hybrid Gray 9 Orange 7 Pink A3 White A Violet A Blue Land cruiser Green 9 Light Blue 7 Black B3 Black B Blue/Black B Red RAV4 (smart key) White 9 Blue 7 White B4 Black B White B Blue Es White 9 Gray 7 Blue A3 Black A Black A Blue Gs Yellow 9 Blue 7 Pink B3 Black/White A Blue/White B Red/Black Gs Yellow 9 Blue 7 Pink B3 Black/White B Blue/White B Red/Black Gs Yellow 9 Blue 7 Pink B3 Black/White B Blue/White B Red/Black Gs 450 hybrid Yellow 9 Blue 7 Pink B3 Black/White B Blue/White B Red/Black Gs Yellow 9 Blue 7 Pink B3 Black/White B Blue/White B Red/Black Is Light Blue 9 Blue 7 Black B4 Light Green B Blue/White B Red/Black Is Light Blue 9 Blue 7 Black B4 Light Green B Blue/White B Red/Black Is-f Light Blue 9 Blue 7 Black B4 Light Green B Blue/White B Red/Black Ls White 9 Orange 7 White B3 Red B Green B Blue Ls 600 hybrid White 9 Orange 7 White B4 Light Green B Green B Red/Black

7 Page 7 of BLADE-AL(TB)-TL Doc. No.: ##848## type 4 WIRING DIAGRAM AND WIRING CROSS-REFERENCE CHART WARNING DO NOT CONNECT ANY OTHER ACCESSORY, IGNITION OR START WIRE FROM THE REMOTE STARTER TO THE VEHICLE. THE INTERFACE MODULE IS HANDLING THE REQUIRED VEHICLE POWERS AND START SEQUENCE FROM THE PUSH TO START BUTTON CIRCUIT. REQUIRED: x RELAYS 3x DIODES PINK BLUE KEYPORT NOTE: FACTORY KEYFOB WILL NOT FUNCTION WHEN REMOTE STARTER IS ENGAGED. FOR AFTERMARKET KEYFOB FUNCTIONALITY, HARDWIRE REMOTE STARTER DOORLOCK AND ALARM OUTPUTS A 86 V (+) KEYSENSE (-) STATUS OUTPUT (-) BRAKE INPUT (+) WARNING IGNITION IS IS USED ONLY AS AN A INPUT TO THE REMOTE STARTER, NOT A AN OUTPUT TO TO THE THE VEHICLE. DIODE CATHODE NEEDS TO BE FACING THE REMOTE STARTER IGNITION (+) A V 30 BRAKE LAMP BRAKE SW IGNITION AT BRAKE PEDAL SWITCH 3 KEY LOCK SOLENOID (+) 4 A EXACT CONNECTOR PIN-OUT WHITE/RED 0 0 WHITE/BLACK WHITE 09 9 PINK/BLACK 08 8 PINK 07 7 BLACK BROWN/RED 06 6 BROWN/YELLOW ORANGE/BLACK 05 5 ORANGE/WHITE ORANGE 04 4 BLUE/RED GREEN/RED BLUE/YELLOW YELLOW GREY/RED 0 GREY/YELLOW WHITE/BLACK WHITE/RED (NC) WHITE - GROUND YELLOW (NC) BROWN/RED (NC) BROWN/YELLOW (NC) ORANGE/BLACK (NC) ORANGE/WHITE (NC) ORANGE (NC) PINK/BLACK (NC) PINK (NC) BLUE/RED (NC) BLUE/YELLOW - PUSH GREEN/RED - CODE GRAY/RED - TXCT GRAY/YELLOW (NC) BLACK (NC) BLUE - CODE LIGHT GREEN - TXCT YELLOW - PUSH (-) ENGINE START STOP model years pin code pin txct pin push pin ignition pin v (BrakE) pin BrakE Prius Blue 5 Light Green 7 Yellow A3 Orange A Black A Blue

8 Page 8 of BLADE-AL(TB)-TL Doc. No.: ##848## type 5 WIRING DIAGRAM AND WIRING CROSS-REFERENCE CHART EXACT CONNECTOR PIN-OUT KEYSENSE (-) WHITE/RED WHITE PINK/BLACK BROWN/RED ORANGE/BLACK ORANGE BLUE/RED GREEN/RED GREY/RED WHITE/BLACK PINK BLACK BROWN/YELLOW ORANGE/WHITE BLUE/YELLOW YELLOW GREY/YELLOW WHITE/BLACK - KEYSENSE (-) WHITE/RED (NC) WHITE - GROUND YELLOW(NC) BROWN/RED (NC) BROWN/YELLOW (NC) ORANGE/BLACK - GROUND ORANGE/WHITE (NC) ORANGE (NC) PINK/BLACK (NC) PINK (NC) BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED - CODE GRAY/RED - TXCT GRAY/YELLOW (NC) BLACK (NC) CODE TXCT model years pin code pin txct keysense pin accessory highlander hybrid Grey 5 Light Blue Green C4 Green RX 400 hybrid Light Green 5 Brown Black C4 Green

9 Page 9 of BLADE-AL(TB)-TL Doc. No.: ##848## Program your module. See programming procedure MoDULE PRoGRAMMING Open PUSH TO START VEHICLE PROGRAMMING the KEYFOB and remove the CIRCUIT BOARD. Place the circuit board against the engine start/stop button. 4 Press the start/stop button. Make sure to obtain a succesful ignition cycle. As soon the ignition will be powered up, the module will begin to MAP the immobilizer encryption. Remove the BATTERY from the circuit board. ENGINE START STOP PUSH The LED will blink BLUE and RED 5 during the learning process, Keep the vehicle ignition ON. REMOVE LED BLINKING COLORS 3 Confirm there isn t another RFID fob in the vehicle. Try to start the vehicle by pressing on the brake pedal and the start/stop button. If the vehicle 6 Wait for the LED to illuminate solid BLUE for SECONDS. refuses to start you are ready to proceed with step 4. If the vehicle starts, Programming is complete. find and remove the remaining RFID fob from the vehicle before proceeding with step 4. LED ON SEC VEHICLES WITH KEY PROGRAMMING VEHICLES WITH KEYPORT PROGRAMMING Insert the vehicle key into the ignition. Insert the key into the keyport. Once the key will be inserted in the ignition the learning process will begin, which will be indicated by the LED flashing BLUE and RED as long as the module is learning. Once the key will be inserted in the keyport the learning process will begin, which will be indicated by the LED flashing BLUE and RED as long as the module is learning. LED BLINKING COLORS LED BLINKING COLORS

10 Page 0 of BLADE-AL(TB)-TL Doc. No.: ##848## MoDULE DIAGNostIcs MODULE DIAGNOSTICS DURING PROGRAMMING SOLID RED MODULE WAITING FOR MORE VEHICLE INFORMATIONS LED BLUE SOLID THEN OFF CORRECTLY FLASHING RED MISSING/WRONG CONNECTIONS OR FIRMWARE LED OFF NO ACTIVITY OR ALREADY MODULE DIAGNOSTICS DURING REMOTE START FLASHING BLUE CORRECTLY AND OPERATIONAL SOLID RED INCORRECTLY FLASHING RED INCORRECTLY LED OFF INVALID GROUND WHEN RUNNING STATUS FROM R.S. MODULE DIAGNOSTICS WITH IGNITION OFF SOLID RED NOT AND STILL WAITING FOR VEHICLE INFO LED OFF AT REST AND READY FOR A R.S. SEQUENCE FLASHING RED INCORRECTLY OR CONNECTED FLASHING FALSE GROUND WHEN RUNNING STATUS FROM R.S. FACTORY RESET PROCEDURE Disconnect the BLADE from Press and hold the programming The LED will begin to flash red. 3 4 the remote starter. button while re-connecting the Immediately release the programming BLADE to the remote starter. FACTORY RESET HOLD button. The LED will turn on solid red for seconds to confirm module reset. Once the reset is confirmed, reconnect all the remaining connectors and repeat the programming procedure DISCONNECT BLADE RE-CONNECT BLADE WHEN THE LED FLASHES RED, RELEASE THE BUTTON SOLID RED LED CONFIRMS RESET

11 Doc. No.: ##848## PUSH TO START VEHICLE USER NOTE ATTENTION! PRIOR TO ENTERING THE VEHICLE.... Press the UNLOCK button on your after-market remote or OEM fob.. You will then have a 45 second delay during which you have to step in the vehicle and press on the brake pedal to complete take over without engine shutdown. 3. Please note that if an RFID remote is present in the vehicle, it will prevent proper remote start sequence.