U.S. Patent No. 8,856,780 INSTALL TYPE SELECTION INSTALL TYPE

Transcription

1 Automotive Data Solutions Inc. INSTALL GUIDE ADS-AL(DL)-HA1-EN AVAILABLE FOR : ADS-AL CA Rev. Date: November 0, 201 Doc. No.: ##45584## HA1 U.S. PATENT NO. 8,856,80 PLEASE VISIT FOR COMPLETE PRODUCT DETAILS The brand names and logos found in this guide are property of their respective owners. Automotive Data Solutions Inc. 201 NOTICE: The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. This guide has been written for properly trained technicians; a certain level of skill & knowledge is therefore assumed. Please!review the Installation Guide carefully before beginning any work.

2 Page 2 of 11 ADS-AL(DL)-HA1-EN Doc. No.: ##45584## INSTALL TYPE SELECTION FEATURES MAKE MODEL YEAR INSTALL TYPE DATA IMMOBILIZER BYPASS ACURA ARM OEM ALARM DISARM OEM ALARM DOOR LOCK DOOR UNLOCK TRUNK/HATCH RELEASE POWER LIFTGATE POWER SLIDING DOOR (L) POWER SLIDING DOOR (R) DOOR STATUS OUTPUT TRUNK STATUS OUTPUT HOOD STATUS OUTPUT** TACHOMETER OUTPUT E-BRAKE OUTPUT A/M ALARM CTRL FROM OEM REMOTES A/M RS CTRL FROM OEM REMOTES AUTOLIGHT CTRL* EL RSX TL TSX Accord / Hybrid Civic / Hybrid CR-V Element Odyssey Ridgeline *This feature will unlock then lock the vehicle s doors on RS shutdown. To turn it off, deactivate the RAP shutdown. **Available only if vehicle is equipped with factory hood switch. HONDA

3 Page 3 of 11 ADS-AL(DL)-HA1-EN Doc. No.: ##45584## WARNING: READ CAREFULLY IMPORTANT I II III Ground When Running from Remote Starter must be provided BEFORE Ignition. Failure to comply may result in immobilizer bypass malfunction during remote start. If Ground When Running from Remote Starter CAN T be provided BEFORE Ignition, use a separate TB-HA for immobilizer bypass ONLY. - DO NOT program unlock before start on the Remote Starter. - DO NOT change Remote Starter OEM alarm control default settings. Failure to comply may result in product malfunction.

4 Page 4 of 11 ADS-AL(DL)-HA1-EN Doc. No.: ##45584## TYPE 1 - CROSS REFERENCE CHART MAKE ACURA MODEL YEAR HONDA DESCRIPTION NAME TYPE POSITION POLARITY MODULE LOCATION COMPONENT LOCATOR TSX TSX Accord 03-0 Accord Hybrid 05 Accord Hybrid 06-0 Odyssey Ridgeline Ignition 1 ~ White pin 6 Black/Yellow (+) Ignition switch ~ Data ~ White pin 2 Red/Blue (DATA) Ignition switch ~ Security Light ~ White pin 5 Blue/Orange (-) Ignition switch ~ Doorlock Data ~ Green 21 pin 4 Brown/Red (DATA) Dash fuse box, driver side ~ Ignition ~ White pin 6 Black/Yellow (+) Ignition switch ~ Data ~ White pin 2 Red (DATA) Ignition switch ~ Security Light ~ White pin 5 Orange (-) Ignition switch ~ Doorlock Data ~ Green 21 pin 4 Brown/Red (DATA) Dash fuse box, driver side ~ Ignition ~ White pin 6 Black/Yellow (+) Ignition switch ~ Data ~ White pin 2 Red/Blue (DATA) Ignition switch ~ Security Light ~ White pin 5 Blue/Orange (-) Ignition switch ~ Doorlock Data ~ Green 21 pin 4 Brown/Red (DATA) In driver door harness ~ Ignition ~ White pin 6 Black/Yellow (+) Ignition switch ~ Data ~ White pin 2 Yellow (DATA) Ignition switch ~ Security Light ~ White pin 5 Red (-) Ignition switch ~ Doorlock Data ~ ~ 21 pin 4 LtGreen (DATA) Dash fuse box, driver side ~ Ignition ~ White pin 6 Black/Yellow (+) Ignition switch ~ Data ~ White pin 2 Yellow (DATA) Ignition switch ~ Security Light ~ White pin 5 Red (-) Ignition switch ~ Doorlock Data ~ Green 21 pin 4 Brown/Red (DATA) Dash fuse box, driver side ~ Ignition ~ Green pin 6 Black/Yellow (+) Ignition switch ~ Data ~ Green pin 2 Red/Blue (DATA) Ignition switch ~ Doorlock Data ~ Green 21 pin 4 Green/Red (DATA) In driver door harness ~ Ignition ~ Green pin 6 Black/Green (+) Ignition switch ~ Data ~ Green pin 2 Red/Blue (DATA) Ignition switch ~ Doorlock Data ~ Green 21 pin 4 Brown/Black (DATA) Dash fuse box, driver side ~

5 Page 5 of 11 ADS-AL(DL)-HA1-EN Doc. No.: ##45584## TYPE 1 - WIRING DIAGRAM STANDARD 12 VOLT, GROUND AND IGNITION SWITCH CONNECTIONS ARE STILL REQUIRED FROM THE REMOTE STARTER REMOTE STARTER DATA SECURITY LIGHT IGNITION 1 (+) TACH (AC) INPUT E-BRAKE (-) INPUT STARTER (+) OUTPUT RIGHT SLIDING DOOR (-) OUTPUT LEFT SLIDING DOOR (-) OUTPUT DISARM (-) OUTPUT TRUNK (-) OUTPUT UNLOCK (-) OUTPUT LOCK (-) OUTPUT 12V (+) GROUND (-) GWR (-) OUTPUT REQUIRED -> HOOD STATUS (-) INPUT OPTIONAL -> TRUNK STATUS (-) INPUT OPTIONAL -> DOOR STATUS (-) INPUT LEGEND NOT REQUIRED IN (1-WAY) NOT REQUIRED IN (2-WAY) USE OR HARD MODE GWR (-) INPUT - BLUE/WHITE (NC) WHITE GROUND - BLACK 12V (+) - RED LOCK/ARM (-) INPUT - GREEN/BLACK UNLOCK (-) INPUT - BLUE/BLACK TRUNK (-) INPUT - RED/WHITE DISARM (-) INPUT - BROWN LEFT SLIDING DOOR (-) INPUT - PURPLE/YELLOW RIGHT SLIDING DOOR (-) INPUT - PURPLE/BLACK (NC) WHITE STARTER (+) INPUT - BLACK/WHITE E-BRAKE STATUS (-) OUTPUT - GREEN TACH (AC) OUTPUT - PURPLE/WHITE WHITE/BLACK - SECURITY LIGHT INPUT WHITE/RED - SECURITY LIGHT OUTPUT WHITE (NC) YELLOW/BLACK - DOOR STATUS (-) OUTPUT YELLOW/RED - TRUNK STATUS (-) OUTPUT YELLOW - HOOD STATUS (-) OUTPUT* BROWN/RED (NC) BROWN/YELLOW (NC) ORANGE/BLACK - KEY DATA ORANGE/WHITE (NC) ORANGE - DOORLOCK DATA PINK/BLACK (NC) PINK - IGNITION (+) INPUT NOTE SINCE THE MODULE INCLUDES A DISARM INPUT FEATURE, BOTH UNLOCK BEFORE START AND LOCK AFTER START FEATURES ARE NOT REQUIRED. WARNING AS MODULE PROGRAMMING PROCEDURE WILL ONLY FUNCTION WITH THE VEHICLE S MASTER KEY, IT IS IMPORTANT TO OBTAIN ALL VALID KEYS IN ORDER TO IDENTIFY THE MASTER KEY. BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED (NC) GRAY/YELLOW (NC) DOORLOCK DATA CONNECTION IS ONLY REQUIRED IF REMOTE START CONTROL FROM OEM REMOTES IS DESIRED A V (+) IGNITION 2 (+) PIN LOCATED AT DRIVER S SIDE FUSEBOX REFER TO WIRING CROSS REFERENCE CHART FOR

6 Page 6 of 11 ADS-AL(DL)-HA1-EN Doc. No.: ##45584## TYPE 2 - CROSS REFERENCE CHART MAKE MODEL YEAR DESCRIPTION NAME ACURA TYPE POSITION POLARITY HONDA MODULE LOCATION COMPONENT LOCATOR RSX RSX EL Civic/ Civic Hybrid CR-V CR-V Element Ignition ~ Green pin 6 Yellow/Black (+) Ignition switch ~ Data ~ Green pin 2 Red/Blue (DATA) Ignition switch ~ Ignition ~ Green pin 6 Black/Yellow (+) Ignition switch ~ Data ~ Green pin 2 Red/Blue (DATA) Ignition switch ~ Ignition ~ Green pin 6 Yellow/Black (+) Ignition switch ~ Data ~ Green pin 2 Red/Blue (DATA) Ignition switch ~ Ignition ~ Green pin 6 Yellow/Black (+) Ignition switch ~ Data ~ Green pin 2 Red/Blue (DATA) Ignition switch ~ Ignition ~ Green pin 6 Yellow/Black (+) Ignition switch ~ Data ~ Green pin 2 White (DATA) Ignition switch ~ Ignition ~ Green pin 6 Black/Yellow (+) Ignition switch ~ Data ~ Green pin 2 White (DATA) Ignition switch ~ Ignition ~ Green pin 6 Black/Yellow (+) Ignition switch ~ Data ~ Green pin 2 White (DATA) Ignition switch ~

7 Page of 11 ADS-AL(DL)-HA1-EN Doc. No.: ##45584## TYPE 2 - WIRING DIAGRAM STANDARD 12 VOLT, GROUND AND IGNITION SWITCH CONNECTIONS ARE STILL REQUIRED FROM THE REMOTE STARTER. REMOTE STARTER DATA SECURITY LIGHT IGNITION (+) TRUNK (-) OUTPUT UNLOCK (-) OUTPUT LOCK (-) OUTPUT 12V (+) GROUND (-) GWR (-) OUTPUT LEGEND NOT REQUIRED IN (1-WAY) NOT REQUIRED IN (2-WAY) USE OR HARD MODE CONNECT TO GROUND TO ENABLE AUTOMATIC RELOCK AFTER START GWR (-) INPUT - BLUE/WHITE (NC) NO GROUND - BLACK 12V (+) - RED LOCK/ARM (-) INPUT - GREEN/BLACK UNLOCK/DISARM (-) INPUT - BLUE/BLACK TRUNK (-) INPUT - RED/WHITE (NC) BROWN (NC) PURPLE/YELLOW GROUND (-) INPUT - PURPLE/BLACK (NC) WHITE (NC) BLACK/WHITE (NC) GREEN (NC) PURPLE/WHITE WHITE/BLACK - SECURITY LIGHT INPUT WHITE/RED - SECURITY LIGHT OUTPUT WHITE (NC) YELLOW/BLACK (NC) YELLOW/RED (NC) YELLOW (NC) BROWN/RED (NC) BROWN/YELLOW (NC) ORANGE/BLACK - KEY DATA ORANGE/WHITE - DOORLOCK DATA ORANGE (NC) PINK/BLACK (NC) PINK - IGNITION (+) INPUT BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED (NC) GRAY/YELLOW (NC) WARNING AS MODULE PROGRAMMING PROCEDURE WILL ONLY FUNCTION WITH THE VEHICLE S MASTER KEY, IT IS IMPORTANT TO OBTAIN ALL VALID KEYS IN ORDER TO IDENTIFY THE MASTER KEY DOORLOCK DATA PIN LOCATED BEHIND DRIVER S SIDE FUSEBOX

8 Page 8 of 11 ADS-AL(DL)-HA1-EN Doc. No.: ##45584## TYPE 3 - CROSS REFERENCE CHART MAKE MODEL YEAR DESCRIPTION ACURA NAME TYPE POSITION POLARITY MODULE LOCATION COMPONENT LOCATOR TL TL 0-08 Ignition 1 ~ White pin 6 Black/Green (+) Ignition switch ~ Ignition 2 ~ Green 5 pin 3 Yellow (+) Keyless module, above brake pedal ~ Data ~ White pin 2 Red/Blue (DATA) Ignition switch ~ Security Light ~ White pin 5 Blue/Orange (-) Ignition switch ~ Doorlock Data ~ Green 21 pin 4 Brown/Black (DATA) Dash fuse box, driver side ~ Ignition 1 ~ White pin 6 Black/Green (+) Ignition switch ~ Ignition 2 ~ Green 5 pin 3 Yellow (+) Keyless module, above brake pedal ~ Data ~ White pin 2 Yellow (DATA) Ignition switch ~ Security Light ~ White pin 5 Orange (-) Ignition switch ~ Doorlock Data ~ Green 21 pin 4 Brown/Black (DATA) Dash fuse box, driver side ~

9 Page 9 of 11 ADS-AL(DL)-HA1-EN Doc. No.: ##45584## TYPE 3 - WIRING DIAGRAM STANDARD 12 VOLT, GROUND AND IGNITION SWITCH CONNECTIONS ARE STILL REQUIRED FROM THE REMOTE STARTER REMOTE STARTER DATA SECURITY LIGHT IGNITION 1 (+) TACH (AC) INPUT E-BRAKE (-) INPUT STARTER (+) OUTPUT RIGHT SLIDING DOOR (-) OUTPUT LEFT SLIDING DOOR (-) OUTPUT DISARM (-) OUTPUT TRUNK (-) OUTPUT UNLOCK (-) OUTPUT LOCK (-) OUTPUT 12V (+) GROUND (-) GWR (-) OUTPUT REQUIRED -> HOOD STATUS (-) INPUT OPTIONAL -> TRUNK STATUS (-) INPUT OPTIONAL -> DOOR STATUS (-) INPUT LEGEND NOT REQUIRED IN (1-WAY) NOT REQUIRED IN (2-WAY) USE OR HARD MODE GWR (-) INPUT - BLUE/WHITE (NC) WHITE GROUND - BLACK 12V (+) - RED LOCK/ARM (-) INPUT - GREEN/BLACK UNLOCK (-) INPUT - BLUE/BLACK TRUNK (-) INPUT - RED/WHITE DISARM (-) INPUT - BROWN LEFT SLIDING DOOR (-) INPUT - PURPLE/YELLOW RIGHT SLIDING DOOR (-) INPUT - PURPLE/BLACK (NC) WHITE STARTER (+) INPUT - BLACK/WHITE E-BRAKE STATUS (-) OUTPUT - GREEN TACH (AC) OUTPUT - PURPLE/WHITE WHITE/BLACK - SECURITY LIGHT INPUT WHITE/RED - SECURITY LIGHT OUTPUT WHITE (NC) YELLOW/BLACK - DOOR STATUS (-) OUTPUT YELLOW/RED - TRUNK STATUS (-) OUTPUT YELLOW - HOOD STATUS (-) OUTPUT* BROWN/RED (NC) BROWN/YELLOW (NC) ORANGE/BLACK - KEY DATA ORANGE/WHITE (NC) ORANGE - DOORLOCK DATA PINK/BLACK (NC) PINK - IGNITION (+) INPUT NOTE SINCE THE MODULE INCLUDES A DISARM INPUT FEATURE, BOTH UNLOCK BEFORE START AND LOCK AFTER START FEATURES ARE NOT REQUIRED. WARNING AS MODULE PROGRAMMING PROCEDURE WILL ONLY FUNCTION WITH THE VEHICLE S MASTER KEY, IT IS IMPORTANT TO OBTAIN ALL VALID KEYS IN ORDER TO IDENTIFY THE MASTER KEY. CONNECTION IS ONLY REQUIRED IF REMOTE START CONTROL FROM OEM REMOTES IS DESIRED. KEYLESS MODULE - ABOVE BRAKE PEDAL GREEN BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED (NC) GRAY/YELLOW (NC) DOORLOCK DATA PIN LOCATED AT DRIVER S SIDE FUSEBOX A 86 12V (+) IGNITION 2 (+) REFER TO WIRING CROSS REFERENCE CHART FOR 30

10 Page 10 of 11 ADS-AL(DL)-HA1-EN Doc. No.: ##45584## INSTALLATION MODE SELECTION 1 Press and release programming button to select installation mode. LED flashes (1X) once = LED flashes (2X) twice = STANDARD HARD MODE 2! Press and hold programming button until LED turns solid GREEN to register selection. After registration, follow Factory Reset Procedure to change installation mode and restart this procedure. MODULE PROGRAMMING PROCEDURE 1 Insert key into ignition. 3 Wait, LED will turn solid GREEN for 2 seconds. 2 ON Turn key to ON position. 4 5 OFF Turn key to OFF position. Module Programming Procedure completed.

11 Page 11 of 11 ADS-AL(DL)-HA1-EN Doc. No.: ##45584## IDENTIFY VEHICLE YEAR 1 Locate the Vehicle Identification Number (VIN), identify the 10th character then match it to its corresponding year. Æ 4 3 A 5 Y 1 N 5 T A L 8 D 5 R 0 X Æ A 1980 L 1990 Y 2000 A 2010 B 1981 M B 2011 C 1982 N C 2012 D 1983 P D 2013 E 1984 R E 2014 F 1985 S F 2015 G 1986 T G 2016 H 198 V H 201 J 1988 W J 2018 K 1989 X K 2019 LED STATUS Flashing RED DIAGNOSTICS DURING PROGRAMMING DURING REMOTE START WITH IGNITION OFF Missing/wrong information from firmware or vehicle Incorrectly programmed Solid RED Waiting for more vehicle information Incorrectly programmed Flashing GREEN Additional steps required to complete programming MODULE DIAGNOSTICS Correctly programmed and operational Incorrectly programmed or connected Not programmed waiting for more vehicle information False ground when running status from remote starter Solid GREEN then OFF Correctly programmed Reset in progress Reset in progress OFF No activity or already programmed Invalid ground when running status from remote starter At rest and ready for a remote start sequence FACTORY RESET PROCEDURE 1 2 DISCONNECT all connectors from module EXCEPT the black 4-PIN standard or optional data connector. DISCONNECT black 4-PIN standard or optional data connector. 5 6 LED will turn solid red for 2 seconds. RESET COMPLETED. RECONNECT all connectors. 3 PRESS AND HOLD programming button while connecting either 4-PIN standard or optional data connector.! Repeat programming procedure. Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. 4 When LED flashes red, RELEASE programming button.