INSTALL GUIDE ADS-TB-GM-EN

Transcription

1 Automotive Data Solutions Inc. INSTALL GUIDE ADS-TB--EN AVAILABLE FOR : ADS-TB Rev. Date: May 18, 2017 Doc. No.: ##39487## U.S. PATENT NO. 8,856,780 PLEASE VISIT FOR COMPLETE PRODUCT DETAILS The brand names and logos found in this guide are property of their respective owners. Automotive Data Solutions Inc NOTICE: The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. This guide has been written for properly trained technicians; a certain level of skill & knowledge is therefore assumed. Please!review the Installation Guide carefully before beginning any work.

2 Page 2 of 7 ADS-TB--EN Doc. No.: ##39487## INSTALL TYPE SELECTION CHeVroLeT CadILLaC BUICK MaKe ModeL year InsTaLL Type Allure Century Lacrosse LeSabre / Ultra Park Avenue Rainier Regal Rendez-vous Terraza CTS Deville Escallade Escallade EXT Seville SLS SLS SRX STS STS Astro Avalanche Blazer Cavalier Express Impala Monte Carlo S10 / S Silverado SSR Suburban Tahoe Trailblazer Uplander Venture 99 2 Venture saturn saab pontiac oldsmobile IsUZU HUMMer C MaKe ModeL year InsTaLL Type Envoy Jimmy Safari Savana Sierra/ CK Sonoma Yukon / Denali H Ascender Hombre Alero Aurora Bravada Intrigue Silhouette 99 2 Silhouette Aztek Bonneville Grand Am Grand Prix Grand Prix Montana 99 2 Montana Montana SV Sunfire Transport x Relay S NOTE I Please advise that this firmware does not disarm OEM alarm. For OEM alarm arm/disarm application, we recommend using the DL-1, 2, 3 or 4 firmwares (see our website for compatibilty charts).

3 Page 3 of 7 ADS-TB--EN Doc. No.: ##39487## TYPE 1 - WIRING DIAGRAM STANDARD 12 VOLT, GROUND AND IGNITION SWITCH CONNECTIONS ARE STILL REQUIRED FROM THE REMOTE STARTER. VEHICLE IGNITION REMOTE STARTER IGNITION (+) OUTPUT 12V (+) GROUND (-) GROUND WHEN RUNNING (-) OUTPUT LEGEND NOT REQUIRED IN (1-WAY) NOT REQUIRED IN (2-WAY) USE OR HARDWIRE MODE GWR (-) INPUT - BLUE/WHITE (NC) WHITE GROUND - BLACK 12V (+) - RED WHITE/BLACK (NC) WHITE/RED (NC) WHITE (NC) IGNITION (+) INPUT - PINK (NC) PINK/BLACK DATA - ORANGE (NC) GRAY/YELLOW (NC) GRAY/RED (NC) GREEN/YELLOW (NC) GREEN/RED (NC) BLUE/YELLOW (NC) BLUE/RED DATA

4 Page 4 of 7 ADS-TB--EN Doc. No.: ##39487## TYPE 2 - WIRING DIAGRAM STANDARD 12 VOLT, GROUND AND IGNITION SWITCH CONNECTIONS ARE STILL REQUIRED FROM THE REMOTE STARTER. REMOTE STARTER PK3 GRAY ORANGE PURPLE BLACK BLUE PINK 12V (+) GROUND (-) GROUND WHEN RUNNING (-) OUTPUT LEGEND NOT REQUIRED IN (1-WAY) NOT REQUIRED IN (2-WAY) USE OR HARDWIRE MODE GWR (-) INPUT - BLUE/WHITE (NC) WHITE GROUND - BLACK 12V (+) - RED WHITE/BLACK (NC) WHITE/RED (NC) WHITE (NC) IGNITION INPUT ECM SIDE - PINK IGNITION OUTPUT IMMOBILIZER SIDE - PINK/BLACK (NC) ORANGE (NC) GRAY/YELLOW DATA OUTPUT - GRAY/RED (NC) GREEN/YELLOW (NC) GREEN/RED (NC) BLUE/YELLOW (NC) BLUE/RED

5 Page 5 of 7 ADS-TB--EN Doc. No.: ##39487## TYPE 3 - WIRING DIAGRAM STANDARD 12 VOLT, GROUND AND IGNITION SWITCH CONNECTIONS ARE STILL REQUIRED FROM THE REMOTE STARTER. VEHICLE IGNITION REMOTE STARTER PK3 PASS KEY III THEFT DETERRENT : MODULE, BEHIND DRIVER SIDE DASH, RIGHT OF STEERING COLUMN YELLOW/BLACK IGNITION (+) OUTPUT 12V (+) GROUND (-) GROUND WHEN RUNNING (-) OUTPUT LEGEND NOT REQUIRED IN (1-WAY) NOT REQUIRED IN (2-WAY) USE OR HARDWIRE MODE GWR (-) INPUT - BLUE/WHITE (NC) WHITE GROUND - BLACK 12V (+) - RED WHITE/BLACK - GROUND WHITE/RED (NC) WHITE - STARTER ENABLE (-) OUTPUT IGNITION (+) INPUT - PINK (NC) PINK/BLACK DATA (J1850) - ORANGE (NC) GRAY/YELLOW (NC) GRAY/RED (NC) GREEN/YELLOW (NC) GREEN/RED (NC) BLUE/YELLOW (NC) BLUE/RED DATA OBDII CONNECTOR LOCATED UNDER DRIVER SIDE DASH

6 Page 6 of 7 ADS-TB--EN Doc. No.: ##39487## INSTALLATION MODE SELECTION 1 Press and release programming button to select installation mode. LED flashes (1X) once = LED flashes (2X) twice = STANDARD HARDWIRE MODE 2! Press and hold programming button until LED turns solid GREEN to register selection. After registration, follow Factory Reset Procedure to change installation mode and restart this procedure. MODULE PROGRAMMING PROCEDURE 1 Insert key into ignition. 3 Wait, LED will turn solid GREEN for 2 seconds. 2 START Turn key to START position. (Engine running) 4 OFF Turn key to OFF position. 5 Module Programming Procedure completed.

7 XX-XX PATENT INSTALL GUIDE PAGE X-X Page 7 of 7 ADS-TB--EN Doc. No.: ##39487## IDENTIFY VEHICLE NOTICE YEAR 1 Locate the Vehicle Identification Number (VIN), identify the 10th character then match it to its corresponding year. Æ 4 3 A 5 Y 1 N 5 T A L 8 D 5 R 0 X Æ a 1980 L 1990 y 2000 a 2010 B 1981 M B 2011 C 1982 n C 2012 d 1983 p d 2013 e 1984 r e 2014 F 1985 s F 2015 G 1986 T G 2016 H 1987 V H 2017 J 1988 W J 2018 K 1989 X K 2019 Led status Flashing RED diagnostics during programming during remote start WITH IGnITIon off Missing/wrong information from firmware or vehicle Incorrectly programmed Solid RED Waiting for more vehicle information Incorrectly programmed Flashing GREEN Additional steps required to complete programming MODULE DIAGNOSTICS Correctly programmed and operational Incorrectly programmed or connected Not programmed waiting for more vehicle information False ground when running status from remote starter Solid GREEN then OFF Correctly programmed Reset in progress Reset in progress OFF No activity or already programmed Invalid ground when running status from remote starter At rest and ready for a remote start sequence FACTORY RESET PROCEDURE 1 2 DISCONNECT all connectors from module EXCEPT the black 4-PIN standard or optional data connector. DISCONNECT black 4-PIN standard or optional data connector. 5 6 LED will turn solid red for 2 seconds. RESET COMPLETED. RECONNECT all connectors. 3 4 PRESS AND HOLD programming button while connecting either 4-PIN standard or optional data connector. When LED flashes red, RELEASE programming button. 7! Repeat programming procedure. Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. This product is protected by one or more of the following patents: U.S. LETTERS PATENT NO. 5,719,551; 6,011,460; 6,243,004; 6,249,216; 6,275,147; 6,297,731; 6,346,876; 6,392,534; 6,529,124; 6,696,927; 6,756,885; 6,756,886; 6,771,167; 6,812,829; 6,924,750; 7,010,402; 7,031,826; 7,046,126; 7,061,137; 7,068,153; 7,015,830; 7,205,679; 7,224,083; 7,369,936; 7,378,945; 7,489,233; 7,501,937; CANADIAN PATENT NO. 2,320,248; 2,415,023; 2,426,670; 2,414,991; 2,415,011; 2,415,027; 2,415,038; 2,415,041; 2,502,893; 2,451,490; 2,452,296; 2,451,487; EUROPEAN PATENT NO. 1,053,128; DE T2; U.S ; ; ; ; ; ; EP ; ; ;