Electro Controls. Valves / Linkages WattsIndustries.co.uk

Transcription

1 Electro Controls Valves / Linkages - 07 WattsIndustries.co.uk

2 valves / linkages Section MOUNTING INSTRUCTIONS FOR LINKGES EE.. M K / EE..ES / EE..RD EE..MK UTO MNUL UTO MNUL UTO MNUL. Push the valve spindle fully down.. Slide the linkage onto the valve spindle. olt the linkage onto the valve body and then tighten the spindle screws.. Manually rotate the motor anti-clockwise to the closed position.. Screw the motor onto the linkage using the screws provided ensuring the valve stem remains fully down.. s the motor rotates clockwise the valve spindle should move upwards. Manually operate the motor and ensure that the spindle moves up and down freely. For the spring return motor spacers are provided which must be fitted to the linkage, underneath the motor. EE -ES EE-ES UTO MNUL If fitted, remove the manual handle from the valve shaft. Rotate the valve shoe to close the required port (the shoe position is indicated by the flat section on the valve shaft.) Mount the bracket onto the valve body using the valve bolts or those provided with the linkage. Fit the coupling over the valve shaft, aligning the flats. Manually close the motor and fit onto the valve coupling and mounting bracket. The actuator and mounting bracket can be fitted in any position to rotate the valve shoe between the centre port and either one of the other two ports. UTO MNUL If fitted, remove the manual handle from the valve shaft. Rotate the valve shoe to close the required port (the shoe position is indicated by the flat section on the valve shaft.) Mount the bracket onto the valve body using the bolts on the valve or those provided with the linkage. Remove the U bracket assembly from the motor. Fit the motor coupling over the valve shaft, aligning the flats. Manually close the motor and fit onto the valve coupling and mounting bracket. Fit the handle onto the motor aligning the splines and bolt in position to valve stem. The actuator and mounting bracket can be fitted in any position to rotate the valve shoe between the centre port and either one of the other two ports. EE-RD / EE-RD EE-ES UTO MNUL Close the valve by rotating the spindle fully clockwise. The valve is closed when the line on valve stem points in line with the valve body. Mount the bracket onto the valve body using the bolts provided. Slide the sleeve onto the valve spindle. DO NOT clamp the motor onto the valve spindle without this sleeve. Manually close the motor by turning it clockwise and screw it onto the bracket using the screws provided. UTO MNUL Fit the mounting bracket onto the valve body with the two Mx bolts. Fit the valve coupling onto the valve spindle aligning the 'D' flat towards the required closed port. Fit the motor over the valve coupling. The D flat on the valve spindle indicates the closed port. To change the direction of rotation remove the 'U' bolt assembly/coupling from the motor by releasing the circlip on the underside and reverse the adaptor sleeve. Sleeve splines up = clockwise Sleeve splines down = anticlockwise Open Closed The actuator and mounting bracket can be fitted in any position to rotate the valve shoe between the centre port and either one of the other two ports. wattsuk@wattswater.com \ wattsindustries.co.uk

3 valves / linkages LL VLVES WY E.. These way all Valves are suitable for use in heating and air conditioning applications to control the flow of chilled water, hot water and up to 0% glycol in closed circuit systems. In open circuits ie mains water or cooling, mineral deposits will impair the operation. E.. E.. to H - ody = rass E..FL -ody = ronze all : rass Nickel Plated all Gasket : PTFE Valve Stem Gasket : Rubber EPDM Rotary travel 90º Flanged valves to PN Full ore Passage Tight Shut-off The motor Part Number must be clearly specified to match each valve ordered. Supplied complete with mounting bracket for the motor. Select motor type E0..E..E..E.. from separate data sheet. Type Size Kvs Max Diff Pressure Max Pressure Media Temp Select Motor m³/h ar ar ºC E- mm ½" SP Female. - E0.. ER0.. E0-0mm ¾" SP Female. - E0.. ER0.. E-C mm " SP Female 7 - E0.. ER0.. E-D mm ¼" SP Female 70 - E.. ER0.. E0-E 0mm ½" SP Female - E.. ER0.. E0-F 0mm " SP Female 9 - E.. ER0.. E-G mm ½" SP Female 0 - E.. ER0.. E...H E.. FL CCESSORIES: EE-7E Linkage Kit with ER-0.. spring return actuator - mm EE-E Linkage Kit with ER-0.. spring return actuator 0-0mm FLOW CHRTS: E...H E.. FL T: + (0) \ F: + (0)

4 valves / linkages Section LL VLVES WY E.. These way all Valves are suitable for use in heating and air conditioning applications to control the flow of chilled water, hot water and up to 0% glycol in closed circuit systems. In open circuits ie mains water or cooling towers, mineral deposits will impair the operation. For diverting applications install in the return pipe only. For mixing applications install in the flow pipe. There must be inlets and outlet stream at all times. Reversal of this will cause vibration and water hammer. E.. ody : E..T..LG = rass ody : E.. FL Flange: Cast Iron all : rass Nickel Plated all Gasket : PTFE Valve Stem Gasket : Rubber EPDM Rotary travel : 90º Flange valves to PN Full ore Passage Tight Shut-off Type Size Kvs Max Diff Max Pressure Port Position Media Temp Select Motor m³/h Pressure ar ar Table ºC E-T mm ½" SP Female. - E0.. ER0.. E0-T 0mm ¾" SP Female. - E0.. ER0.. E-TC mm " SP Female - E0.. ER0.. E-TD mm ¼" SP Female - ER0.. E0-LE 0mm ½" SP Female. - ER0.. E0-LF 0mm " SP Female. - ER0.. Supplied complete with mounting bracket for the motor. The motor Part Number must be clearly specified to match each valve ordered. Select motor type E0..E..E..E.. from separate data sheet. CCESSORIES: EE-7E Linkage Kit with ER-0.. spring return actuator - mm EE-E Linkage Kit with ER-0.. spring return actuator 0 - mm FLOW CHRTS: E..T..LG E.. FL wattsuk@wattswater.com \ wattsindustries.co.uk

5 valves / linkages LIFT & LY / SET VLVES & WY MK.. MKDN.. MKDN.. These mixing valves are suitable for diverting or mixing applications in closed hot water, chilled water & up to 0% glycol systems. In open circuits, ie mains water or cooling towers, mineral deposits will impair the operation. For diverting applications the valve must be installed in the return pipe only. For mixing or diverting there must be inlets and outlet stream. Reversal of these will cause vibration & water hammer. MK.. Stainless steel spindle Flanged valves to PN Rangeability 0: Media temp. C to C Tight Shut off Max. pressure ar Equal percentage flow characteristic Leakage 0.% Kvs Type Size Max Diff Pressure Kvs Lift Height Valve ody Select Motor ar m³/h mm Material Spring Rtn MK mm ½" SP rass E0.. ER0.. MK0 0mm ¾" SP rass E0.. ER0.. MK mm " SP 9 rass E0.. ER0.. MK mm ¼" SP. rass E0.. ER0.. MK0 0mm ½" SP. 9 rass E0.. ER0.. MK0 0mm " SP. rass E0.. ER0.. MKDN0 0mm " Flanged. 0 Cast Iron E.. ER0.. MKDN mm ½" Flanged 0 Cast Iron E.. ER0.. MKDN0 0mm " Flanged 0 0 Cast Iron E.. ER0.. MKDN0 0mm " Flanged Cast Iron E.. ER0.. ORDER VLVE + LINKGE + SEE SEPRTE DT SHEET TO SELECT. H W L D VLUE SIZE W L H D MK ½" 0 9 MK0 ¾" 0 9 MK " MK ¼" 9 MK0 ½" 9 MK0 " 0 9 MKDN0 0mm MKDN mm 9 0 MKDN0 0mm 0 00 MKDN0 mm CCESSORIES: EE-MK Linkage Kit for MK to MK0 screwed valves Suitable for use with E0.. E.. motors ONLY EE-MK Linkage Kit for MKDN0 flanged valve Suitable for use with E.. motors ONLY EE-MK Linkage Kit for MKDN, MKDN0, MKDN0 flanged valves Suitable for use with E.. motors ONLY EE-MK Linkage Kit for MK to MK0 screwed valves For Spring Return ER0 motors ONLY EE-MK Linkage Kit for MKDN0 flanged valves For Spring Return ER0 motors ONLY EE-MK Linkage Kit for MKDN, MKDN0 flanged valves For Spring Return ER0 motors ONLY EXMPLES: M MIXING VLVE Valve stem UP Valve stem DOWN TYPICL PPLICTIONS STRIGHT THROUGH lank ottom Port M to open to open DIVERTING For port valves the bottom port must be blanked - Reduce ΔP Install the valve with the spindle at any angle vertical to 0 above horizontal. M Flow Rate m /h Flow chart MKDN0 MKDN Pressure Drop P kpa MKDN MKDN0 MK0 MK0 MK MK MK0 MK T: + (0) \ F: + (0)

6 valves / linkages Section ROTRY VLVES & WY.. C.. F.. F.. valves flanged to PN range of rotary valves mm to 0mm suitable for diverting or mixing water in closed circuit heating applications. Media temperature C to C In open circuits ie mains water, cooling towers etc. mineral deposits will impair the operation. The position of the shoe is always opposite the flat on the spindle. G.. F.. Material :.. C.. & F.. rass Cast Iron body, rass shoe, Stainless Steel spindle. The valve can be installed with the spindle at any angle vertical to 0 above the horizontal plane. ll leakage rates are measured at a differential pressure of 0. ar. Type Size Kvs Leakage % Kvs Max Static Select Spring m³/h Mixing Diverting Pressure Nm Motor Return - mm ½" SP. <0.% <0.% ar EK.. E0.. ER mm ¾" SP <0.% <0.% ar EK.. E0.. ER mm ¾" SP. <0.% <0.% ar E0.. ER0.. - mm " SP <0.% <0.% ar E0.. ER0.. - mm " SP <0.% <0.% ar E0.. ER0.. - mm ¼" SP <0.% <0.% ar E0.. ER0.. C0 0mm ¾" SP <% <0.% ar E0.. ER0.. C mm " SP <% <0.% ar E0.. ER0.. C mm ¼" SP <% <0.% ar E0.. ER0.. C0 0mm ½" SP <% <0.% ar E.. ER0.. C0 0mm " SP 0 <% <0.% ar E.. ER0.. F0 0mm " Flanged 0 <% <0.% ar EK.. E.. ER0.. F mm ½" Flanged 90 <% <0.% ar E.. ER0.. F0 0mm " Flanged 0 <% <0.% ar E.. ER0.. F0 0mm " Flanged <% <0.% ar E.. ER0.. F mm " Flanged 0 <% <0.% ar E.. ER0.. F0 0mm " Flanged 00 <% <0.% ar E.. ER0.. ORDER VLVE + LINKGE + - SEE DT SHEET ON S. For ports blank the middle port - reduce ΔP On.. and C.. for 0 rotation remove the red disc under the knob VLVE D E VLVE D E C0 C 7 C. 7 7 C C VLVE C D E F F F F0. 9 F F MIXING DIVERTING D C E Dimensions D & E are for E0.. E.. motors only D & E will be less for EK.. & more for ER.. On.. and C.. for 0 rotation remove the red disc under the knob The motor can operate between ports - or - CCESSORIES: EE-ES Linkage Kit - use EK.. motors ONLY EE-M Linkage for Satchwell M valve - use E0..& E.. motors ONLY EE-ES Linkage Kit - use E0..& E.. motors ONLY EE-MF Linkage for Satchwell MF valve - use E.. motors ONLY EE-ES Linkage Kit - use ER0.. motors ONLY EE-ES Linkage Kit - use ER0.. motors ONLY FLOW CHRTS: m³/ h) Flow (m 0 0 h) ow (m³/ Flo.0.0 C0 C0 C C C0 Flow Rate l/s 0 0 F0 F F0 F0 F F Pressuredrop (kpa) Pressure drop (kpa) Pressure Drop P kpa wattsuk@wattswater.com \ wattsindustries.co.uk

7 valves / linkages UTTERFLY VLVES RD.. These ring butterfly valves are used to control liquid flow in closed circuit heating systems. RD.. valves have a small leakage rate and are suitable for normal hot water boiler applications. RDP.. valves have tight shut-off characteristics (see below) and are suitable for hot water, chilled water and up to 0% glycol systems. In open circuits ie mains water, cooling towers, mineral deposits will impair the operation. RD.. Materials: Cast Iron ody, rass disc, Stainless Steel spindle, Graphite asbestos packing gland. Media temp. C - C The RDP.. valves have a PTFE lining providing tight shut-off and allowing standard actuators to be used. LRGER SIZES VILLE ON REQUEST Type Size Max Diff Press Kvs Leakage Max Static Press Select Motor Spring mm ar m³/h %Kvs ar Nm Nm Return RD 0. E0.. ER0.. RD 0 0. E0.. ER0.. RD E0.. ER0.. RD E.. ER0.. RD 0. E.. ER0.. RD E.. ER0.. RD E.. ER0.. RD E.. ER0.. RD E.. ER0.. RDP- 0.0 E0.. ER0.. RDP E0.. ER0.. RDP E0.. ER0.. RDP E.. ER0.. RDP- 0.0 E.. ER0.. RDP E.. ER0.. RDP E.. ER0.. RDP E.. ER0.. RDP E.. ER0.. RDP E.. Nm motor only. SELECT VLVE + LINKGE + SEE SEPRTE DT SHEET TO SELECT. CCESSORIES: Fit valve between mating flanges for pressure ratings required between PN to PN VLVE SIZE DN D H H W L mm mm mm H H 0mm mm mm L 0mm W mm mm L= Valve face to face dimension 00mm DN D when using E0.. E.. E.. When using ER.. EE-RD Linkage Kit for RD valves --0mm Suitable for use with E0.. and E.. motors ONLY EE-7RD Linkage Kit for RD 00mm valves. Suitable for use with E.. motors ONLY EE-RD Linkage Kit for RD valves -0mm Suitable for use with ER0.. spring return motors ONLY EE-9RD Linkage Kit for RD valves 0-0mm Suitable for use with ER0.. spring return motors ONLY EXMPLES: Flow Rate m /h mm 0mm mm 0mm 0mm mm 0mm 0mm mm mm Typical pplication For use in low pressure hot water (LPHW) heating systems to prevent water flow through unfired boilers in a multi-boiler installation. RD.. valves can also be used as zone valves where slight leakage in the closed position is acceptable. RDP.. valves can be used on applications which require shut off ie. hot water, chilled water and up to 0% glycol systems. Operation When installed in a boiler return pipeline and the system requires the boiler to operate, a control signal/changeover contact can be used to motor open the valve and allow water to flow through the boiler. The burner can then operate under the control of the boiler thermostat. motor with auxiliary switches can be used to ensure that the valve is open before the burner operates Pressure Drop P kpa Installation: Install the valve with the spindle at any angle from vertical to 0 degrees above the horizontal plane. T: + (0) \ F: + (0)

8 valves / linkages Section ISED SPRING RETURN VLVES & PORT EZV.. ORDER UXILIRY SWITCH SEPRTELY Media temp. C to C & port spring return valves for zoning & diverting in closed circuit hot water, chilled water & up to 0% glycol systems. Supplied complete with motors. EZV-.. EZV-.. Max. pressure ar Consumption W Max ambient 0 C Materials: brass body, rubber ball/plug for 0% shut off. Wiring cable 0.m uto/manual lever Replaceable motor Type Connection Max Diff Press Kvs Supply Motor Spring pplication Enclosure ar m³/h ±% Open Close EZV- ½" SP VC s s Zone IP0 EZV- mm comp VC s s Zone IP0 EZV- ¾" SP VC s s Zone IP0 EZV- mm comp VC s s Zone IP0 EZV- " SP VC s s Zone IP0 EZV- mm comp VC s s Zone IP0 EZV- ½" SP.. 0VC 0s s Diverting IP0 EZV- mm comp... 0VC 0s s Diverting IP0 EZV- ¾" SP. 7. 0VC 0s s Diverting IP0 EZV- mm comp VC 0s s Diverting IP0 EZV- " SP 0.. 0VC 0s s Diverting IP0 EZV- mm comp VC 0s s Diverting IP0 EZV-M uxiliary switch for EZV.. 0VC () SPST The volt free contact closes when the valve is fully open 7 EZV EZV-.. 9 Install the valve with the motor at any angle vertical to 0 above the horizontal plane. UTO MN UTO MN D E Type D E EZV-,,, 79 EZV-, 0 FLOW CHRTS: 0 0 EZV-.. EZV-.. WIRING: EZV-.. 0 yellow / green 0 earth blue brown thermostat black black neutral live } auxiliary switch Type EZV - M P kpa P kpa EZV-.. valve blue brown neutral live l /min l /min yellow / green earth valve thermostat black black auxiliary switch } Type EZV - M EXMPLES: EZV-.. INLET OUTLET motor off INLET OUTLET motor on (auto) MNUL LEVER INLET OUTLET motor off manual lever locked open EZV-.. LOD RETURN motor off LOD RETURN motor on (auto) MNUL LEVER LOD RETURN motor off manual lever locked open wattsuk@wattswater.com \ wattsindustries.co.uk 7

9 ELECTRO CTLOGUE-UK-W-UK UK-W-UK-0-07-Rev0 Watts Industries UK Ltd Colmworth usiness Park, Eaton Socon, St. Neots, PE9 YX, UK T: + (0) F: + (0) wattsuk@wattswater.com wattsindustries.co.uk 07 Watts