Third Editin First Printing Operatr's Manual Safety Rules Danger Failure t bey the instructins and safety rules in this manual will result in death r serius injury. D Nt Operate Unless: Yu learn and practice the principles f safe machine peratin cntained in this peratr's Avid hazardus situatins. Knw and understand the safety rules befre ging n t the next sectin. 2 Always perfrm a pre-peratin inspectin. 3 Always perfrm functin tests prir t use. 4 Inspect the wrkplace. 5 Only use the machine as it was intended. Yu read, understand and bey the manufacturer's instructins and safety rules safety and peratr's manuals and machine decals. Yu read, understand and bey emplyer's safety rules and wrksite regulatins. Yu read, understand and bey all applicable gvernmental regulatins. Yu are prperly trained t safely perate the machine. Part N. 97780 Genie TZ-34/20
Operatr's Manual Third Editin First Printing Cntrls 3 4 5 STOP 6 7 2 8 0 9 Platfrm Cntrl Panel Functin enable buttn fr: Platfrm dwn Primary bm dwn Primary bm retract Secndary bm dwn Turntable rtate right 2 Functin enable buttn fr: Platfrm up Primary bm up Primary bm extend Secndary bm up Turntable rtate left 3 Red Emergency Stp buttn 4 Bm functin speed cntrller 5 Primary bm extend/retract buttn 6 Platfrm verlad indicatr light (if equipped) 7 Primary bm up/dwn buttn 8 Platfrm level buttn 9 Secndary bm up/dwn buttn 0 Turntable rtate buttn 8 Genie TZ-34/20 Part N. 97780
Third Editin First Printing Operatr's Manual CONTROLS 5 6 7 4 3 STOP 8 2 0 9 3 2 Grund Cntrl Panel Outrigger raise/lwer buttn (individual utrigger) 2 Outrigger aut level buttn 3 Functin enable buttn fr: Platfrm dwn Primary bm dwn Primary bm retract Secndary bm dwn Turntable rtate right Outrigger lwer 4 Functin enable buttn fr: Platfrm up Primary bm up Primary bm extend Secndary bm up Turntable rtate left Outrigger raise 5 5 amp breaker fr cntrls circuits 6 Red Emergency Stp buttn 7 Key switch fr grund/ff/ platfrm selectin 8 Platfrm verlad indicatr light (if equipped) 9 Platfrm level buttn 0 Primary bm extend/ retract buttn Primary bm up/dwn buttn 2 Secndary bm up/dwn buttn 3 Turntable rtate buttn Part N. 97780 Genie TZ-34/20 9
Operatr's Manual Third Editin First Printing Pre-peratin Inspectin Fundamentals It is the respnsibility f the peratr t perfrm a pre-peratin inspectin and rutine maintenance. D Nt Operate Unless: Yu learn and practice the principles f safe machine peratin cntained in this peratr's Avid hazardus situatins. 2 Always perfrm a pre-peratin inspectin. Knw and understand the pre-peratin inspectin befre ging n t the next sectin. 3 Always perfrm functin tests prir t use. 4 Inspect the wrkplace. 5 Only use the machine as it was intended. The pre-peratin inspectin is a visual inspectin perfrmed by the peratr prir t each wrk shift. The inspectin is designed t discver if anything is apparently wrng with a machine befre the peratr perfrms the functin tests. The pre-peratin inspectin als serves t determine if rutine maintenance prcedures are required. Only rutine maintenance items specified in this manual may be perfrmed by the peratr. Refer t the list n the next page and check each f the items. If damage r any unauthrized variatin frm factry delivered cnditin is discvered, the machine must be tagged and remved frm service. Repairs t the machine may nly be made by a qualified service technician, accrding t the manufacturer's specificatins. After repairs are cmpleted, the peratr must perfrm a pre-peratin inspectin again befre ging n t the functin tests. Scheduled maintenance inspectins shall be perfrmed by qualified service technicians, accrding t the manufacturer's specificatins and the requirements listed in the respnsibilities 0 Genie TZ-34/20 Part N. 97780
Third Editin First Printing Operatr's Manual PRE-OPERATION INSPECTION Pre-peratin Inspectin Be sure that the peratr's, safety and respnsibilities manuals are cmplete, legible and in the strage cntainer lcated n the platfrm. Be sure that all decals are legible and in place. See Decals sectin. Check fr hydraulic il leaks and prper il level. Add il if needed. See Maintenance sectin. DC mdels: Check fr battery fluid leaks and prper fluid level. Add distilled water if needed. See Maintenance sectin. Check fr prper tire pressure and lug nut trque. Add air t tires if needed. See Maintenance sectin. Check the fllwing cmpnents r areas fr damage, imprperly installed r missing parts and unauthrized mdificatins: Electrical cmpnents, wiring and electrical cables Hydraulic pwer unit, reservir, hses, fittings, cylinders and maniflds Bm cmpnents and wear pads Tires and wheels Trailer lights and reflectrs Parking brake cmpnents Outriggers and ft pads Limit switch and alarms Nuts, blts and ther fasteners Platfrm entry mid-rail/gate Surge brake cmpnents Safety chains (if required) Light and brake cables Mechanical brake cmpnents (if equipped) Axle cmpnents Beacn and alarms (if equipped) Check entire machine fr: Cracks in welds r structural cmpnents Dents r damage t machine Be sure that all structural and ther critical cmpnents are present and all assciated fasteners and pins are in place and prperly tightened. Be sure that the batteries are in place and prperly cnnected. Mdels equipped with hydraulic surge brake systems: Check the hydraulic il level in the surge brake. Check fr leaks. After yu cmplete yur inspectin, be sure that all cmpartment cvers are in place and latched. Part N. 97780 Genie TZ-34/20