AUTOMATION PRODUCTS IN HYDRAULICS AND PNEUMATICS PNEUMATIC CYLINDERS

AUTOMATION PRODUCTS IN HYDRAULICS AND PNEUMATICS PNEUMATIC CYLINDERS

PNEUMATIC CYLINDERS SERIES LUTHRA ( Standard Heavy Duty Cylinders ) 1-9 SERIES T CYLINDER 10 ISO 6431 SERIES A Old version of ISO Dimensional Stardards 11- SERIES 90 ISO 15552 Latest version of ISO dimensional standards *(This version is available with mountings only ) 17-21 HYDRAULIC CYLINDER SERIES 10 22-23

PNEUMATIC CYLINDERS RANGE SERIES - STANDARD RANGE (Heavy duty), Tie Rod Construction FEATURES Covers : Cast Iron Heavy Duty Tube :,, 63, 75 Aluminium 63 - available in Brass also 75 - available in steel also 75-3 bore Steel duly honed & Hard chrome Plated Piston Rod : EN8 ground & hard chrome plated Seals: Nitrile (80 c), Viton (0 C) TYPES AVAILABLE A) DOUBLE ACTING SINGLE ENDED forward stroke Air Reverse stroke Air AIR INLET PORT SHAFT U CUP SEAL VIPER SEAL PISTON PISTON U CUP SEAL CUSHION SLEEVE TUBE AIR INLET PORT REAR COVER SHAFT COVER O RING SLEEVE O RING FRONT COVER TIE ROD CUSHIONING SEAL 1

B) DOUBLE ACTING DOUBLE ENDED (Shaft on both side) forward stroke Air Reverse stroke Air AIR INLET PORT SHAFT U CUP SEAL VIPER SEAL PISTON PISTON U CUP SEAL CUSHION SLEEVE TUBE SHAFT COVER O RING SLEEVE O RING FRONT COVER CUSHIONING SEAL Note : for parts and seal details Refer Page No.1 C) SINGLE ACTING SPRING RETURN TYPE forward stroke Air Reverse stroke by spring force FRONT COVER P REAR COVER SPRING D) SINGLE ACTING - Spring to forward type, Air to Return (in this types spring comes towards the rear cover Reverse stroke by Air & forward stroke by spring force E) VALVE MOUNTED CYLINDER In this type cylinder construction is same as given on Pg 1 except that valve to operate the cylinder is mounted directly on the cylinder. No external Tubing is Required from valve to cylinder port. Only one Inlet pressure port has to be connected to the valves inlet port. This type of cylinder is usually used to operate Butterfly valves. 2

F) BALANCER CYLINDER FOR POWER PRESS Single Acting Air to lift and return by load TOP COVER (REAR COVER) LARGE OPENING PROVIDED FOR FASTER EXHAUST EXTERNAL FLANGE MOUNTING PLATE CUSHION U SEAL CUSHION SLEEVE SLEEVE O RING PISTON PISTON U CUP SEAL TUBE COVER O RING AIR IN BOTTOM COVER (FRONT COVER) HIGHER SIZE PORT IN BOTTOM COVER (1 OR 1.1/2 BSP) ACETYL BEARING STRIP SHAFT U SEAL VIPER SEAL SHAFT This type of cylinder has bottom cover thicker than the standard cylinder show on Pg1. to accommodate larger port size for inlet Air. Also Top cover is provided with a circular opening at the back duly fitted with wire mesh for dust protection. This larger circular opening is provided for faster exhaust of the cylinder in the forward & Reverse stroke. Dimension of Balancer Cylinder available on request only as most of the cylinders are made as per Individual clients requirements. 3

COMPRESSED AIR CONSUMPTION Unit : lpm percycle Note : 1 cycle comprises of 1 forward and 1 return stroke of a standard pneumatic cylinder. The stroke length of the cylinder considered in this table is 100mm. Bore (mm) 63 80 100 1 1 0 0 0 ROD (mm) 8 9.5 11.5 35 35 51 2 Area (mm ) A 314 491 804 1963 31 24 78 12266 17663 310 49063 706 B 264 4 700 1055 1762 26 33 7359 114 701 266 47021 68608 Operating 1 0.115 0.181 0.299 0.460 0.741 1.142 1.902 3.027 4.69 6.84 12.27 19.12 27.71 pressure 2 0.172 0.271 0.448 0.689 1.110 1.711 2.848 4.533 7.02 10.24 18. 28.63 41. (Bar) 3 0.229 0.361 0.597 0.918 1.479 2.279 3.795 6.039 9.36 13.64 24.48.15 55.29 4 0.287 0.2 0.746 1.146 1.847 2.848 4.741 7.544 11.69 17.05.59 47.66 69.08 5 0.344 0.542 0.895 1.375 2.2 3.4 5.687 9.0 14.03. 36.69 57.17 82.87 6 0.1 0.6 1.044 1.604 2.585 3.984 6.633 10.556.36 23.85 42.80 66.69 96.65 7 0.8 0.722 1.193 1.833 2.953 4.553 7.580 12.062 18.69 27. 48.91 76. 110.44 8 0.515 0.812 1.342 2.062 3.2 5.121 8.526 13.568 21.03.65 55.01 85.71 124.23 9 0.573 0.902 1.490 2.290 3.691 5.690 9.472 15.074 23.36 34.06 61.12 95.23 1.02 10 0.6 0.992 1.639 2.519 4.060 6.8 10.418.580.69 37.46 67.22 104.74 151.81 Let us assume we have three cylinder working independently in different circuits. Cylinder A : mm Bore, stroke length 75mm operating at 12 cycles / minute Cylinder B : 80 mm Bore, stroke length 0mm operating at 10 cycles / minute Cylinder C : 0 mm Bore, stroke length 900mm operating at 13 cycles / minute From the table given above the air consumption at 6 bar working pressure of the cylinder would be Cylinder A : 0.6 x12cycles/min. x1.1( fos) = 8.34 lpm Cylinder B : 0.633 x2.5(multiplication factor) x10cycles/min. x 1.1( fos) = 182.5 lpm Cylinder C : 42.8 x9(multiplication factor) x13cycles/min. X1.1( fos) = 58 lpm Fos : Factor of safety (10%) FORCE CONSIDERATION : Selection of cylinder is based upon the bore, stroke & the piston rod diameter. This is further based upon the force required to do the work & distance to be traversed. The force available at a certain pressure is determined by the following chart. FORCE CALCULATION FOR PNEUMATIC CYLINDER UNIT : kgf 1 Newton approx. Series cylinder E-EXTENDED STROKE R-REVERSE STROKE equal to 0.1 Kgf BELOW VALUES ARE INCLUSIVE OF FRICTIONAL LOSSES PRESSURE : BAR (KG/cm2) Normal Bore Actual bore Force(kgf) 2 BAR 3 BAR 4 BAR 5 BAR 6 BAR 7 BAR 8 BAR 9 BAR 10 BAR mm.4 mm E 9 13 18 22 27 31 36 14 R 8 12 15 19 23 27 31 34 37 mm mm E 61 71 80 90 100 R 17 33 41 58 67 75 82 mm 54 mm E 60 80 101 121 141 1 181 2 R 37 55 74 92 111 129 147 6 184 65 mm 65 mm E 59 88 118 147 176 4 233 263 292 R 75 100 1 149 174 199 223 0 75 mm 80.5 mm E 88 133 176 226 267 1 355 398 443 R 80 121 1 1 2 279 1 361 0 100 mm 105 mm E 152 2 6 392 467 536 613 691 764 R 144 218 289 363 433 5 578 652 7 1 mm 1 mm E 235 353 470 598 707 823 937 1054 1171 R 218 8 436 543 655 764 872 980 1088 1 mm 157 mm E 343 519 686 862 1029 11 1372 1544 1715 R 8 490 652 813 976 1137 1299 1460 27 0 mm 7.5 mm E 598 897 1196 1519 1793 92 2391 2685 2989 R 578 867 1156 1441 1733 19 28 97 2881 0 mm 8.5 mm E 931 1392 1852 28 2783 42 3704 4635 R 892 13 1784 22 2675 3121 3567 13 49 0 mm 9.5 mm E 1333 1994 2656 3391 3989 4743 5312 5973 6635 R 1294 19 88 34 81 4228 5170 5821 6463 4

SERIES DIMENSIONAL REVIEW : DOUBLE ACTING CYLINDER J THDS. H.B.S.P.THDS. D N G THDS. E F E M L K A+STROKE B C CHART A: DOUBLE ACTING SINGLE ENDED CYLINDER NOMINAL *(B) (A) (A) 65 (A) & (B) 75 (A) I.D. OF TUBE (A) 63 80 MODEL NO. 1 215 A2 A214 / B214 N NN- 5 5 6.5 6.5 M 24. 36.5 47.5 58 70.5 L 55 63 76 92 K 19 J M5 M6 M6 M8 M10 H 1/8 B.S.P. ¼ B.S.P. ¼ B.S.P. ¼ B.S.P. ½ B.S.P. G M8 x 1. M12 x 1. M12 x 1. M x 1.5 M x 2.5 F 9.5 15.9 15.9.4.4 E 34 48 48 D 10 26 26 35 C 15 B.5 46 51 A 58 84 84 102 119 TUBE (A) - Aluminium (B) - Brass CHART B : DOUBLE ACTING SINGLE ENDED CYLINDER (STEEL TUBE ) 65 S 75 S 100 S 1 S 1 S 0 S 0 S 0 S 3 S I.D. OF TUBE 63 80 105 1 157 7.5 8.5 9.5 357 MODEL NO. 214 3 4 5 6 8 210 212 2 N 6.5 6.5 6.5 8 8 10 10 10 M 58 70.5 88 112 126 170.5 210 247 292 L 76 92 122 152 172 2 286 335 2 K 35 35 55 A3 J M8 M10 M10 M12 M12 M M M24 27x2 H ¼ B.S.P ½ B.S.P ½ B.S.P ½ B.S.P ½ B.S.P ¾ B.S.P ¾ B.S.P ¾ B.S.P 1 B.S.P G M x 1.5 M x 2.5 Mx2.5 M24x3 M24x3 Mx3.5 M42x4.5 M42x4.5 2 B.S.F F.4.4.4 35 35.7.7 60 E 48 48 55 64 64 70 90 90 110 D 35 35 44 55 55 C 56 68 68 75 B 46 51 51 58 62 68 75 75 60 A 102 119 119 1 135 2 5 5 2 Note: 1) Piston rod diameter threads are subject to change for stroke lengths above 10 mm stroke. The same will be as per mutual agreement between client and vendor. Separate dimensional drawing will be submitted by us. 2) TUBE Material A - Aluminium B - Brass S - Steel 5

PNEUMATIC CYLINDER : MOUNTING DETAILS FRONT FLANGE MOUNTING G A X VIEW XX B A X E C REAR FLANGE MOUNTING S+STROKE X A F-DIA D X A 19 65 75 100 1 1 0 0 0 A B C D E F G S 5 5 10 10 13 13 13 19 19 53 62 80 102 1 1 0 196 2 315 360 4 29 63 80 92 117 0 174 2.5 267 310 43 52 67 84 110 1 137 170 190 265 310 5 19 28 36.5 56 68 93 112 126 170.5 210 247 5.5 5.5 6.5 8.5 10.5 10.5 10.5 12.5 12.5 21 21-10.5 28 28 33 39 43 43 76 80.5 1 134 0 183 183 5 2 4 9 9 REAR CLEVIS MOUNTING A B F D E C J-DIA G H+STROKE A B C D E F G H J 19 65 75 100 1 1 0 0 0 19 22 35 37 46 49 55 70 70 85 115 115 - - 23 36 36 55 77 77 12.5 13 75 78 26.6 22 35 41 64 64 29 63 80 92 114 1 0 215 270 3 8 10 9.5 9.5 15 22 22 S.P. S.P. 27.5.5 54.5 72 90 103 1 172 197 82.5 87.5 147 147 178 2 8 234 2 279 354 354 6 8 12 12 6

SR. PNEUMATIC CYLINDER : MOUNTING DETAILS NECK MOUNTING B+STROKE D E-PITCH OF THDS. F A+STROKE C G A B C D E F G 19 79 53.5 19 7 1.5 10 24 83.5 58 19 7 1.5 122 84 26 9.5 2 34 122 84 26 9.5 2 65 148 102 9.5 2 75 170 119 35 9.5 2 48 60 100 170 119 35 9.5 2 55 65 INTERMEDIATE TRUNNION Port orientation to be specified by client CØ B D Xi A Xi : to be specified by client A B C D 70 15 15 18 65 80.5 75 105 100 1 1 185 35 0 290 52 0 2 1 0 35 7

SR. PNEUMATIC CYLINDER : MOUNTING FOOT MOUNTING H+STROKE G C A+STROKE B D-DIA E F 19 65 75 100 1 1 0 0 0 A B C D E F G H NIL 90 122 134 152 179 179 195 5 2 295 312 NIL 7 9 10 10 12 12 22 22 26 NIL 2 3 3 3 4 4 6 6 9.5 12.7 12.7 NIL 5.5 6.5 8.5 8.5 10.5 10.5 12.5 12.5 21 21 NIL 24. 36.5 60 70.5 88 112 126 170.5 210 247 NIL 60 80 92 114 1 0 215 260 0 NIL 21.6 29 36 52 63 80 87 112 1 4 NIL 97.5 1 157 190 212 212 2 247 296.5 346 359 REAR CLEVIS WITH SWIVEL BRACKET DIA A B C D E F G H J θ F-DIA G 5 62 52 28 5.5 13 82.5 8 θ 10 80 67 36.5 6.5 147 12 10 102 63 84 8.5 147 12 C E 65 13 1 80 110 56 10.5 178 75 13 1 92 1 68 10.5 2 100 13 0 117 137 93 10.5 8 1 19 190 1 170 112 12.5 234 1 19 2 174 190 126 12.5 2 D B A J-DIA 0 315 2.5 265 170.5 21 279 0 360 267 310 21 75 354 0 4 310 5 247 78 354 ROD END FORK K DIA D F G THD. K CV CE B2 H CK I DIA H 24 9.5 M12X1. - 10 19 19 M12X1. 12 18 59 77 65 MX1.5 15 18 62 80 75 MX2.5 15 18 62 80 100 MX2.5 15 18 62 80 1 60.7 M24X3 24 76 100 1 60.7 M24X3 24 76 100 0 70 34 MX3.5-80 64 64 110 0 90 M42X4.5-1 88 80 5 0 90 M42X4.5-1 88 80 5 9.5.4.4 36 36 G-THDS. CE CK D CV F I-DIA B2 8

MODELLING CHART FOR SERIES CYLINDER The chart given below gives the criteria for selecting your model number while ordering spares. However, stroke length is not determined by the chart and has to be specified while ordering spare cylinders. FIRST AND SECOND DIGIT SR. NO. DESCRIPTION DIMENSIONS AS PER LUTHRA STANDARD 51 DIMENSIONS AS PER CLIENTS DRAWING 52 DIMENSIONS AS PER STANDARD CATALOGUE EXCEPT LARGER PISTON ROD DIAMETER USED. THIRD DIGIT SR.NO. DESCRIPTION 1 SINGLE ACTING GRAVITY RETURN TYPE / BALANCER CYLINDER 2 DOUBLE ACTING TYPE 3 DOUBLE ENDED TYPE 4 SINGLE ACTING SPRING RETURN TYPE 5 SINGLE ACTING SPRING TO FORWARD TYPE 6 TANDEM 7 STROKE ADJUSTABLE FEMALE e.g.: Serial no. 52 5 14 4 pneumatic cylinder implies standard LUTHRA dimensions with larger dia piston rod, single acting spring to forward type, bore 65mm and rear clevis mounting. 9

MIDGET CYLINDER SERIES T MIDGET CYLINDERS Series - T cylinders are available in bore sizes of mm. Higher bore sizes of upto mm are available on request. These cylinders have improved aesthetic quality as compared to Tie rod mounted cylinder. Also as the front cover is threaded to the tube, seals can be easily replaced. Cylinder can be directly neck mounted as the front / rear covers are threaded reducing system installation time. *Available in non-cushioned & fixed cushioning type. TECHNICAL CHARACTERISTICS SEALS PISTON Working Pressure : 1 to 10 bar 0 Ambient Temperature : - to 80 c Fluid : filtered air / water Barrel : Brass End Caps : Aluminium Piston : Aluminium Piston Rods : En8 Hard chrome plated Seals : Nitrile b A+STROKE b C H THDS. B+STROKE G THDS. Bore A b F c G thds. H thds. B Shaft Dia. 72 14 55 22 M X1.5 M8X1. 124 9.5 Ø L T Bore L T D A D 12 9 107 A+STROKE 10

ISO 6431 CYLINDERS TYPES SERIES A Tie Rod Mounted Round Aluminum Tube SERIES AX Mickey Mouse Aluminium Tube Instead of Round Aluminium Tube to improve Aesthetics (No Tie Rod Seen) Characteristic Tube - Aluminium Cover - Die Casted Aluminium Piston - Delrin Seals - Nitrile. FEATURES Internal Seals Orientation & parts details refer pg no. 1 Series cylinders the concept is the same. 11

PACE SERIES A (AX) ISO 6431 PNEUMATIC CYLINDER : MOUNTING CUSHION ADJUST RT Ø U S EE E M Ø T Ø T KK AM WH P+ STROKE DIA KK AM dia U dia T e11 S sq.e max. sq.m RT EE WH P M10x1. 11.3 28.5 M5 G1/8 26 94 M12x1. 22 34 55 M6 G1/4 105 Mx1.5 43 22 64.5 46.5 M6 G1/4 34 111 63 Mx1.5 47.5 22 80 56.5 M8 G3/8 37 124 80 MX1.5 42 48 26 97 72 M10 G3/8 41 136 100 MX1.5 42 48 34 118 89 M10 G1/2 47 144 CENTRE TRUNNION TT DIA TD TL TM UR TT XV ØTD UR 12 12 65 * 63 71 22 * 75 92 24 * 63 90 102 28 * TM TL XV 80 110 122 * 100 1 135 * * : to be specified by client CLEVIS FOOT MOUNTING G1 EM ØCK θ DIA K1 G2 S6 CA CK EM G1 ±0.2 H6 R1 max. K2 G3 θ S6 (4 HOLES) CA 18 5.5 10 26 21 8 10 51 31 17 H6 41 22 5.5 36 12 28 24 10 12 54 35 17 6.6 12 33 12 12 65 17 63 52 35 6.6 37 12 67 17 80 66 9 63 47 14 86 60 17 100 76 9 71 60 55 15 96 80 10 K1 K2 G2 G3 12

PACE SERIES A (AX) ISO 6431 PNEUMATIC CYLINDER : MOUNTING FEMALE CLEVIS EB CB MR DIA EB max dia EK L MR CB XD+ tol Ø EK L REAR CLEVIS WITH MOUNTING BRACKET FL D2 (4 HOLES) L2 θ 10 13 11 26 142 ± 2 52 12 15 13 28 0 ± 2 60 12 13 170 ± 2 63 70 17 190 ± 2 80 90 23 17 210 ± 2 100 110 21 60 2 ± 2 DIA TG D2 L2 FL θ 6.4 5.5 22 6.4 8.5 48 6.4 8 27 63 60 8.4 10.5 TG 80 72 10.5 14.5 36 36 100 89 10.5 14.5 41 36 ROD END FORK B3 DIA. KK B2 B3 CE ±0.4 CK Dia H9 CM CV LE M10X1. 26 10 10 12 M12X1. 31 24 48 12 12 14 24 LE MX1.5 39 64 19 63 MX1.5 39 64 19 B2 CM KK D1 80 MX1.5 54 80 100 MX1.5 54 80 CK CV CE d ISO H7 Thread S D B1 L L1 L2 D1 BALL DIA INCH Basic static load capacity Cs kgf 10 M10X1. 26 14 56 43 21 15 3/4 1360 B1 d L L2 S 12 M12X1. 65 24 17.5 7/8 17 / 63 MX1.5 21 83 64 33 22 1 1/8 90 80 / 100 18 MX1.5 46 100 77 27.5 1 3/8 36 D1 SERIES PNEUMATIC CYLINDER: MOUNTING D //65 MM SAME AS ABOVE 75/100 MX2.5 46 100 77 27.5 1 3/8 36 1/1 M24X3 60 31 124 94 48 33.5 1 11/ 7410 L1 0 MX3.5 70 37 1 110 56 2 90 FOR HIGHER SIZE CONTACT FACTORY 13

PACE SERIES A (AX) ISO 6431 PNEUMATIC CYLINDER : MOUNTING FOOT MOUNTING AO AT ØAB 4HOLES DIA TR ± 0.3 diaab AH AO max. AT E SA tol. XA tol. REAR FLANGE 7 11 4 43 142 144 36 9 36 15 4 54 1 ± 1. ± 1. 3 9 15 6 62 170 175 63 9 15 6 82 185 190 80 63 12 63 6 100 210 ± 1.6 215 ± 1.6 100 75 14 71 18 6 117 2 2 Ø FB4 HOLES UF TF ZF+ FRONT FLANGE MF R E DIA TF ±0.3 R ±0.3 FB H13 MF UF E ZF W tol. 64 7 10 80 46 1 72 36 9 10 90 55 1 90 9 12 110 65 155 63 100 9 12 1 83 170 80 126 63 12 155 101 190 100 1 75 14 185 118 5 35 ±2 ±2.5 W MF 14

ISO 6431 PNEUMATIC CYLINDER : MOUNTING REED SWITCH For Magnetic cylinders only Function : The Reed switch is mounted on the tie rod of the pneumatic cylinder. It is used for proximity sensing of the magnet present on the piston of the cylinder. The reed switch sends an electrical impulse to the solenoid valve / other control device when the piston approaches the sensing position. Model : LSBD2 PM (WITH LED) Note : Model : R1 (WITH LED) 1) When inductive loads are switched, a high voltage peak is produced at the moment of switch - off. For this reason, proximity switch must be provided with a protective circuit. 2) The cylinder with magnetically actuated reed switches should not be fitted at places where there are strong magnetic fields. Model Operating voltage Switching current R1 UPTO 48 VDC / 4-2 VAC 5 - ma Reed Switch External Protection circuit R LOAD C Operating temperature Response time Contact rating Switch type 5-60 degrees Celcius On / Off < 1 ms 6 (3) W, 8 (4) VA Normally open LOAD R and C : rating should be based on the load condition 15

MODELING CHART ON ISO 6431 CYLINDER FIRST DIGIT A - Round Aluminium Tube type AX - Mickey Mouse Tube Type SECOND DIGIT - TYPE 2 Double action type 3 Double Ended 4 Single Acting Spring Return 5 Single Acting Spring to Forward THIRD & FOURTH DIGIT - SIZE DIGIT 63 80 63 80 FIFTH DIGIT : MOUNTING TYPE SR.NO. BLANK 1 2 3 4 5 6 7 8 DESC. STD.TIE FRONT REAR FRONT REAR CENTRE FOOT NECK REAR ROD TYPE FLANGE FLANGE CLEVIS CLEVIS TRUNION TRUNION (MALE)

SERIES 90 - ISO 15552 - MOUNTING STANDARDS * AVAILABLE WITH EXTERNAL MOUNTING ONLY Features: COVER :- Bore size - 63 - Aluminium Cover Bore 80-0 - Cast Iron Cover TUBE :- Bore - 63 Aluminium Bore 80 to 0 - M.S. duly Honed & Hard Chrome Plated SEALS :- Nitrile Suitable for 80 C Max. COMPARISON TO STANDARD SERIES LUTHRA CYLINDERS a) More Heavy Duty b) Mounting Dimensions are totally different c) Shaft diameter and threads are different compared to series cylinders Parts & Seals orientation :- Same as shown in Pg. No.1 17

FRONT FLANGE (MF1) SERIES 90 EE MF VIEW XX X DØ KK Threads UF TF R REAR FLANGE (Mf2) - SERIES 90 MF W ± 2.0 X AM FB VIEW XX FBØ MF X EE DØ KK Threads R TF X 63 60 100 1 0 0 0 ZF ± 2.0 DØ.4.4 35.8 KK M12X1. MX1.5 MX1.5 MX1.5 MX1.5 M27X2 M36X2 M36X2 M42X2 AM 24 55 72 72 84 EE 1/4BSP 1/4BSP 3/8BSP 3/8BSP 1/2BSP 1/2BSP 3/4BSP 3/4BSP 3/4BSP W 35 60 70 80 ZF 1 155 170 190 5 2 280 0 3 AM TF R 72 36 90 100 126 63 1 75 180 90 2 115 270 135 3 5 UF 96 115 1 5 187 224 280 3 395 FbØ 9 9 9 12 14 18 22 26 MF 9 9 12 13 13 19 19 CENTRE TRUNION SERIES 90 ISO 15552 MOUNTING - Mt4 VIEW XX X KK Threads DØ EE BSP TDØ TL AM TM X XV TO SPECIFY 18 63 60 100 1 0 0 0 DØ.4.4 35.8 KK M12X1. MX1.5 MX1.5 MX1.5 MX1.5 M27X2 M36X2 M36X2 M42X2 AM 24 55 72 72 84 EE(BSP) 1/4BSP 1/4BSP 3/8BSP 3/8BSP 1/2BSP 1/2BSP 3/4BSP 3/4BSP 3/4BSP TM 63 75 90 110 1 0 0 0 3 TL TD LSQ 55 63 76 92 122 152 172 2 286

SERIES 90 ISO 15552 MOUNTING - FEMALE REAR CLEVIS (MP2) KK Threads DØ EE X DIA CD E AM XD+Stroke X CB UB DØ 63 80.4 100.4 1 35 0 0 0.8 KK M12X1. M12X1. MX1.5 MX1.5 MX1.5 M27X2 M36X2 M36X2 M42X2 AM 24 55 72 72 84 EE 1/4BSP 1/4BSP 3/8BSP 3/8BSP 1/2BSP 1/2BSP 3/4BSP 3/4BSP 3/4BSP XD 0 170 190 210 2 275 315 335 375 CD 12 12 CB 28 60 70 90 90 110 UB 52 60 70 90 110 1 154 170 2 E 55 63 76 92 122 152 175 235 290 MODELLING CHART SERIES 90 ISO 15552 CYLINDER FIRST & SECOND DIGIT = 90 FOR SERIES 90 THIRD DIGIT = 2 FOR DOUBLE ACTING TYPE FOURTH & FIFTH DIGIT - SIZE DIGIT 63 80 04 05 06 08 10 63 80 100 1 0 0 0 SIXTH DIGIT : MOUNTING TYPE SR.NO. BLANK 1 2 4 5 8 DESC. STD.TIE FRONT REAR REAR CLEVIS CENTRE REAR TRUNION ROD TYPE FLANGE FLANGE (FEMALE) TRUNION (MALE) MF1 MF2 MP2 MT4 MP4 19

SERIES 10 : HYDRAULIC CYLINDER Hydraulic Cylinders find their application in FLUID POWER when Force requirement is on the higher side. They are sturdier in construction as compared to pneumatic cylinders and are preferred when jerk free motions are required. These cylinders are available in different shapes & sizes to suit client applications. Series 10 - Square construction assembled and bolting using Tie rods. Simple construction enables easy change of seals. Available in Bore sizes of mm to 0 mm and pressure up to 2 Bar. Mounting accessories can be provided on such as Flange, Pivot, Foot brackets, Trunion etc. Cushioning possible on both ends. Different types manufactured in this series. Double Acting - Forward and return motion by oil. Single Acting - Forward stroke by oil & return by load exerted on the piston rod. SERIES 10 : Features - Cushioning possible at both ends to reduce impact at the end of the stroke. Material of construction - Tube - Carbon Steel duly hard chrome plated. Seals - Fabric reinforced. Covers - Steel Piston - Steel. Piston Rod - En8 hard chrome plated. Guide Bush - Gun Metal 0 Maxm operating pressure - 0 Bar Temperature Range - 85 c SERIES : 10 HYDRAULIC CYLINDER : MOUNTING PXB.S.P qg ZXP T-THDS. qh N SQ M SQ F D N SQ E B S +STROKE A SERIES 10: DOUBLE ACTING HYDRAULIC CYLINDER DIMENSION GØ ZXP PXBSP A B S D E F MSQ HØ N T 18 M14X1.5P 3/8 34 47 10 28 60 35 42 M8 MX1.5P 3/8 37 53 14 75 53 M10 63 35 M27X2P 1/2" 69 18 29 88 55 65 M12 80 M33X2P 3/4" 52 79 55 115 65 82.5 MX2 100 M33X2P 3/4" 58 49 88 22 35 57 1 75 97 MX2 1 56 M42X2P 3/4" 60 67 35 56 5 75 126 M22X1.5 0 70 M48X2P 3/4" 65 56 88 35 68 8 92 155 M27X2 0 100 M64X3 3/4" 76 78 48 90 265 1 198 M36X2 Note : Shaft dia & threads can be offered as per clients requirement also.

SERIES 10 : HYDRAULIC CYLINDER : MOUNTING REAR PIVOT qg EW qcd MR q qh M SQ. L XC+STROKE FRONT FLANGE FT C qg FL FH q qh M SQ. FW FA FC REAR FLANGE FT qg FL F H q qh M SQ. FW XA+STROKE FC XC CD L EW HØ GØ M MRØ FA C FW FC FHØ FL FT XA 7 14 22 18 60 17 22 7 41 87 11 115 10 155 193 36 75 22 23 7 52 106 13.5 1 14 171 63 226 36 55 35 88 22 29 9 65 117 14 142 18 8 80 6 65 115 5 83 149 18 182 236 100 7 36 55 75 1 35 10 97 2 17.5 210 22 274 1 7 64 60 85 56 6 8 126 8 22 260 28 271 0 344 70 70 110 70 8 55 10 155 3 26 3 4 21

Sales & Service Network Jalandhar Ludhiana Chandigarh Gurgaon New Delhi Jaipur Lucknow Ahmedabad Rajkot Vadodara Indore Jamshedpur Kolkata Vapi Aurangabad Nagpur Mumbai New Mumbai Nasik Ahmednagar Pune Sangli Hyderabad Vishakhapatanam Enquire for our product CD which includes a free pneumatic training course on low cost automation! Bangalore Chennai Pondicherry Head Office Coimbatore Dealers Colombo Luthra Hydro Pneumatic Industries 2, Luthra Indl. Premises, 44 - E, M. V. Marg, Safaid Pool, Mumbai - 0 072. Phone : +91-22-6691 6555 / 56 / 57. Fax : +91-22-2851 93. Email : sales@hydropneumatic.net Visit ut at : www.hydropneumatic.net