Actuators Guide blocks or ISO/VDMA cylinders QA/8/51/ QA/8/61/ QA/8/81/ (long coupling) QA/8/85/ (short coupling) Ø 32 to 1 mm QA/8/61/ QA/8/51/ Conorms to ISO 6431, VDMA 24562 and NFE 49 3 1 Ensures protection against external rotary and bending orces Guide rods run through bearings protected by wiper rings Provides accurate guidance or unsupported loads Technical data Operating temperature: C to +8 C maximum Consult our Technical Service or use below +2 C Materials Guide block, nut & mounting plate: anodised aluminium Plain bearings: Sintered bronze (/51/), (/81/), (/85/) Steel roller bearing (/61/) ods: Stainless steel Wiper rings: nitrile rubber 7 Standard models QA/8/51/ (plain bearing) Ø Piston Model Suitable or cylinders rod Ø Magnetic Non-magnetic 32 12 QA/832/51/ A/832/M, PA/18232/M A/832, PA/18232 4 16 QA/84/51/ A/84/M, PA/1824/M A/84, PA/1824 5 2 QA/85/51/ A/85/M, PA/1825/M A/85, PA/1825 63 2 QA/863/51/ A/863/M, PA/18263/M A/863, PA/18263 8 25 QA/88/51/ A/88/M, PA/1828/M A/88, PA/1828 1 25 QA/81/51/ A/81/M, PA/1821/M A/81, PA/1821 Insert stroke length in mm rom table below. QA/8/61/ (roller bearing) Ø Piston Model rod Ø orce (N) Magnetic # Non-magnetic # 32 12 QA/832/61/ QA/832/63 6 A/832/M, PA/18232/MIL # A/832, PA/18232/IIL # 4 16 QA/84/61/ QA/84/63 1 A/84/M, PA/1824/MIL # A/84, PA/1824/IIL # 5 2 QA/85/61/ QA/85/63 15 A/85/M, PA/1825/MIL # A/85, PA/1825/IIL # 63 2 QA/863/61/ QA/85/63 15 A/863/M, PA/18263/MIL # A/863, PA/18263/IIL # 8 25 QA/88/61/ QA/88/63 3 A/88/M, PA/1828/MIL # A/88, PA/1828/IIL # 1 25 QA/81/61/ QA/88/63 3 A/81/M, PA/1821/MIL # A/81, PA/1821/IIL # Insert stroke length in mm rom table below. Locking cartridges should be ordered separately. Active pressure applied to lock, passive pressure released to lock. 2 required per guide block. Standard strokes Passive locking cartridge Ø 5 1 16 2 25 32 4 5 32 º º º º º º º º 4 º º º º º º º º 5 º º º º º º º º 63 º º º º º º º º 8 º º º º º º º º 1 º º º º º º º º Other stroke lengths are not available, use nearest standard stroke. Maximum stroke 5 mm. Locking Suitable or cylinders Note: For all applications please consult our Technical Service # When using guide blocks (QA/8/61) or proile cylinders PA/182 you have to order a model with a barrel which is turned at 9 so that the port threads are in line with the two switch grooves. QA/8/81/ (plain bearing, long coupling) Ø Piston Model Suitable or cylinders rod Ø Magnetic Non-magnetic 32 12 QA/832/81/ A/832/M, PA/18232/M A/832, PA/18232 4 16 QA/84/81/ A/84/M, PA/1824/M A/84, PA/1824 5 2 QA/85/81/ A/85/M, PA/1825/M A/85, PA/1825 63 2 QA/863/81/ A/863/M, PA/18263/M A/863, PA/18263 8 25 QA/88/81/ A/88/M, PA/1828/M A/88, PA/1828 1 25 QA/81/81/ A/81/M, PA/1821/M A/81, PA/1821 Insert stroke length in mm rom table below. QA/8/85/ (plain bearing, short coupling) Ø Piston Model Suitable or cylinders rod Ø Magnetic Non-magnetic 32 12 QA/832/85/ A/832/M, PA/18232/M A/832, PA/18232 4 16 QA/84/85/ A/84/M, PA/1824/M A/84, PA/1824 5 2 QA/85/85/ A/85/M, PA/1825/M A/85, PA/1825 63 2 QA/863/85/ A/863/M, PA/18263/M A/863, PA/18263 8 25 QA/88/85/ A/88/M, PA/1828/M A/88, PA/1828 1 25 QA/81/85/ A/81/M, PA/1821/M A/81, PA/1821 Insert stroke length in mm rom table below. www.norgren.com/ino/en7
Guide blocks with plain bearings QA/8/51/ Ø 32 to 1 mm QA/8/51/ Guide blocks (plain bearing) AD AK + stroke AO AG AJ AV AW AX AE AP A AS AL F AT AW AF AC + ø AM F AW AG A AG AH Adjustment = Notice rangeadjustment range AN BA BB Ø AC + AD AE (A/F) AF (A/F) AG AH AJ AK AL Ø AM AN AO 32 69 + 2 12 15 17 M 6 1 32,5 11 58 1 6 9 4 74 + 2 12 15 19 M 6 1 38 122 64 12 6 11 5 91,5 + 4 15 22 24 M 8 12 46,5 135 8 12 6 19 63 92 + 4 15 22 24 M 8 12 56,5 153 95 12 7 15 8 16 + 6 15 27 3 M 1 15 5 18 13 16 9 14 1 111 + 6 15 27 3 M 1 17 7 199 15 16 9 19 Ø AP A AS AT AV AW Ø AX A BA BB kg at mm kg per 1 mm 32 1 9 74 78 45 32,5 6,6 48 76 9 1,,6 4 16 1 8 84 5 38 6,6 56 85 11 1,2,9 5 125 12 96 1 6 46,5 9 66 99 19 1,8,9 63 132 125 14 15 7 56,5 9 76 114 15 2,2,9 8 165 155 13 13 9 72 11 98 134,5 25 4,1,16 1 185 175 15 15 11 89 11 118 153,5 28,5 5,8,16 Adjustment ranges Note: Supplied complete with mounting screws or cylinder. F (N) 1 5 1 5 81 88 863 85 84 832 1 1 Outstroke (mm) 5 1 5 Please see page 76 or details o mountings. eer to page 7 or details o piston rod guide blocks and page 68 or locking units. Consult our Technical Service or stroke lengths above 5 mm. 71
Actuators Guide blocks with roller bearings QA/8/61/ Ø 32 to 1 mm QA/8/61/ Guide blocks (roller bearing) CA + stroke CB + CC CD CE CF ±,2 T ±,2 CG DM H H7 x 2,5 CK CY DD VI 5 CO -,3 CP C CS CJ CT CW 2,5 + -,1 ø CV 7 DE ±,2 H H7 x 2,5 DC CN K 6 C CX ±,2 DA -,3 DB ±,3 G DF CX ±,2 J (28 min) H H7 2,5 DL CI Adjustment range Centering sleeve Saety zone Blanking plug (remove when using locking cartridge) Ø CA CB + CC CD CE CF ±,2 CG CI CJ (A/F) CK CN 32 177 1 + 5 65 28 12 15,3 6,5 M 6 84,5 13 5 61 4 192 111 + 5 69 33 12 23 6,5 M 6 88 15 6 67 5 237 128 + 1 65 4 15 33,8 9 M 8 94 22 6 75,5 63 237 128 + 1 97 4 15 29,3 9 M 8 98,5 22 6 8 8 28 151 + 1 112 5 2 37 11 M 1 114 27 7 92 1 28 156 + 1 112 55 2 4,5 11 M 1 115,5 27 7 93 Ø CO -,3 CP C CS CT (A/F) Ø CV 7 CW CX ±,2 CY (A/F) C DA -,3 DB ±,3 32 97 9 74 5,5 17 12 61 32,5 5 125 5 45 4 115 11 87 58,5 19 16 69 38 6 14 58 54 5 137 13 14 7,5 24 2 85 46,5 6 15 7 63 63 152 145 119 85,5 24 2 1 56,5 6 182 85 8 8 189 18 148 15,5 3 25 13 72 8 215 15 1 1 213 2 172 13,5 3 25 15 89 8 22 13 12 Ø C Ø DD DE ±,2 DF Ø DG Ø DH H7 DJ Ø DK 6 DL DM T kg at mm kg per 1 mm 32 6,6 11 78 M 6 2 9 M 5 9 45 14 32,5 1,2,18 4 6,6 11 84 M 6 24 9 G 1/8 9 61,5 14 38, 2,2,32 5 9 15 1 M 8 3 11 G 1/8 11 76,5 16 46,5 3,6,49 63 9 15 15 M 8 3 11 G 1/8 11 76,5 16 56,5 4,6,49 8 11 18 13 M 1 48 13 G 1/8 13 119 2 72, 8,7,77 1 11 18 15 M 1 48 13 G 1/8 13 119 2 87, 11,,77 Adjustment range Note: Supplied complete with mounting screws or cylinders and two centering sleeves. Attention When using guide blocks (QA/8/61) or proile cylinders PA/182 you have to order a model with a barrel which is turned at 9 (PA/182/IIL,.../MIL) so that the port threads are in line with the two switch grooves. 72
Guide blocks with roller bearings QA/8/61/ Ø 32 to 1 mm Outstroke Centre o gravity Maximum load capacity is dependent on the outstroke o a horizontally installed guide unit. In the case o short stroke operation, the load capacity igures taken rom the diagram must be multiplied by the correction actor (diagram 2). In the curves o load capacity (diagram 1), the short stroke corrections have already been taken into account or an outstroke > 6 mm. Centre o gravity o load capacity Outstroke The total delection o guide rods will be determined by the addition o that due to own weight (diagram 3) and that due to load capacity (diagram 4). Maximum load capacity depending on outstroke Delection caused by own weight Delection caused by a load o 1 N (diagram 1) (diagram 2) (diagram 3) (diagram 4) Load capacity Correction actor Delection (mm) Delection (mm) ( N ) 5 1, 2,5 2 2,5 832 4,9 2, 2 2, 3,8 1,5 832 1 1,5 2 1 88-81 85-863 84 832 1 2 3 4 5 6 Outstroke (mm),7,6,5 2 4 6 Stroke (mm) 1,,5 1 2 3 4 5 6 Outstroke (mm) 84 85-863 88-81 1 1, 84,5 85-863 88-81 1 2 3 4 5 6 Outstroke (mm) In the case o shock load applications, the igures given in the diagrams above must be reduced by a actor o 2. 73
Actuators Guide blocks with plain bearings (long coupling) Guide blocks with plain bearings (short coupling) QA/8/81/ QA/8/85/ Ø 32 to 1 mm QA/8/81/ Guide blocks (long coupling) CB + CD CA + stroke CC CE CF ±,2 CG DM CK DD CJ CY CO ±,2 CP C CS CT CW ø CV 8 C CX ±,2 DA ±,2 DB ±,3 DC DE ±,2 DF CX ±,2 CL CI Notice adjustment range = Notice adjustment range Ø CA/81 CA/85 CB + /81 CB + /85 CC CD CE CF ±,2 CG CI/81 CI/85 32 174 149 89 + 5 64 + 5 75 24 12 4,3 6,5 M 6 84,7 59,7 4 189 164 99 + 5 74 + 5 8 28 12 11 6,5 M 6 88 63 5 21 181 113 + 1 88 + 1 78 34 15 18, 8 8,5 M 8 94,2 69,2 63 235 21 114 + 1 89 + 1 16 34 15 15,3 9 M 8 98,7 73,7 8 265 24 139 + 1 114 + 1 111 5 2 25 11 M 1 114 89 1 288 265 145 + 1 12 + 1 128 55 2 3 11 M 1 115 9 Ø CJ CK CL/81 CL/85 CO ±,2 CP C CS CT Ø CV 8 CW CX ±,2 32 15 5 27 2 97 93 74 51 17 12 61 32,5 4 15 6 27 2 115 112 87 58,2 19 16 69 38 5 2 6 28 3 137 134 14 7,2 24 2 85 46,5 63 2 6 27 2 152 147 119 85,2 24 2 1 56,5 8 26 7 35 1 189 18 148 15,5 3 25 13 72 1 26 7 35 1 213 26 173 13,5 3 25 15 89 Ø CY C DA ±,2 DB ±,3 Ø DC Ø DD DE ±,2 DF DM kg at mm/81 kg at mm/85 kg per 1 mm 32 5 125 49 45 6,6 11 78 M 6 12 1,2 1,15,18 4 6 14 58 55 6,6 11 84 M 6 12 2,2 2,15,32 5 6 148 7 65 9 15 1 M 8 16 3,6 3,55,49 63 6 178 85 8 9 15 15 M 8 16 4,6 4,55,49 8 8 195 15 1 11 18 13 M 1 2 8,7 8,65,77 1 8 218 13 12 11 18 15 M 1 2 11, 1,95,77 Adjustment ranges Note: Supplied complete with mounting screws or cylinder. 74
Guide blocks with plain bearings (long coupling) Guide blocks with plain bearings (short coupling) QA/8/81/ QA/8/85/ Ø 32 to 1 mm Maximum load or QA/8/81/ and /85/ Outstroke Outstroke Outstroke F 1(N) Centre o gravity o load capacity F (N) Outstroke F 1= F 1= F x F,9x,9 Static Static orce Force: : F 2 = F F x 2 = F x 2 Max. load capacity (diagram 1) is dependent on the outstroke o a horizontally installed guide unit. The total delection o guide rods will be determined by the addition o the amount o delection caused by own weight (according to diagram 2) plus the amount o delection due to load capacity (according to diagram 3). Maximum load capacity depending on outstroke Delection caused by own weight Delection caused by a load o 1 N (diagram 1) (diagram 2) (diagram 3) Load capacity Delection Delection (mm) (mm) Delection Delection (mm) (mm) Load capacity (N) 1 8 ø 8-1 2,5 2, 1,5 ø 32 2,5 2, 1,5 ø 32 6 4 ø 5 ø 63 ø 4 ø 32 1,,5 ø 4 ø 5-63 ø 8-1 2 ø 5-63 ø 8-1 5 1 2 3 4 5 1 2 3 4 5 6 1 2 3 4 5 6 Outstroke (mm) Outstroke (mm) Outstroke (mm) In the case o shock load applications, the igures given in the diagrams above must be reduced by a actor o 2. 1,,5 ø 4 75
4 Actuators ISO/VDMA Cylinder mountings For PA/181,.../M; PA/182,.../M; PA/183,.../M A/28,.../M; A/283,.../M; A/8,.../M; KA/8,.../M M/191,.../M; M/192,.../M; M/193,.../M; PVA/8/M Front or rear stud A ISO 6431 TG BB DD Piston rod swivel AK 4 SW 3 SW 2 SW 4 SW 1 KK KK TG B 1 L 2 F L Ø BB DD TG kg 32 17 M6 32,5,2 4 17 M6 38,2 5 23 M8 46,5,5 63 23 M8 56,5,5 8 28 M1 72,8 1 28 M1 89,8 125 34 M12 11,14 16 42 M16 14,31 2 42 M16 175,31 25 5 M2 22,92 32 6 M24 27 1,46 Thread KK B1 F L L2 SW1 SW2 SW3 SW4 kg M1x1,25 5 26 73 2 19 12 17 3,2 M12x1,25 6 26 77 24 19 12 19 3,2 M16x1,5 8 34 16 32 3 19 24 42,65 M2x1,5 1 42 122 4 3 19 3 42,72 M27x2 13,5 4 147 54 4 24 41 55 1,7 M36x2 18 78 251 72 5 36 55 75 5,4 ear lange B Front lange G ISO 6431 and VDMA 24562 Part 2 UF TF FB MF Foot C ISO 6431 and VDMA 24562 Part 2 AT AH E 1 AU AO ø AB T E Ø E1 Ø FB MF TF UF kg 2 36 6,6 1 55 7,16 25 4 6,6 1 6 76,2 32 5 7 1 32 64 8,25 4 55 9 1 36 72 9,35 5 65 9 12 45 9 11,7 63 75 9 12 5 1 125,8 8 1 12 16 63 126 154 1,35 1 12 14 16 75 15 186 2,2 125 14 16 2 9 18 224 1,7 16 18 18 2 115 23 28 3,1 2 22 22 25 135 27 32 4,6 25 28 26 25 165 33 395 7,4 32 35 33 3 2 4 475 13,6 ear clevis D ISO 6431 and VDMA 24562 Part 2 LH UB CB H 14 L EK 8 Ø Ø AB AH AO AT AU E T kg 2 6,6 27 6 4 16 36 22,3 25 6,6 3 7 4 16 4 26,4 32 7 32 8 (11) 4 24 48 32,15 4 9 36 9 (12) 4 (5) 28 53 36,18 5 9 45 1 (13) 5 32 64 45,3 63 9 5 12 (13) 5 32 74 5,39 8 12 63 19 5 (6) 41 98 63,8 1 14 71 19 5 (6) 41 115 75,95 125 16 9 2 (25) 9 (7) 45 14 9 2,4 16 18 115 2 8 6 18 115 3,5 2 22 135 3 9 7 22 135 5,25 25 26 165 35 1 75 28 165 9,5 32 33 2 45 16 85 35 2 22, ( ) stainless steel, weight on request ear clevis D2 VDMA 24562 Part 2 B2 B1 H 14 2 1 B3 EK1 h 9 M Ø CB H14 Ø EK 8 L LH M UB kg 32 26 1 22 13 52 9 45,11 4 28 12 25 16 6 12 52,16 5 32 12 27 17 68 12 6,22 63 4 16 32 22 79 15 7,34 8 5 16 36 22 99 15 9,54 1 6 2 41 27 119 2 11,9 125 7 25 5 31 139 (14) 25 13 2,7 16 9 3 55 35,5 181 3 17 4,3 2 9 3 6 36 181 3 17 6,1 25 11 4 7 45 218 4 2 1,9 32 12 45 8 5 238 45 22 3,5 ( ) Stainless steel, weight on request 76 Ø B1 H14 B2 B3 Ø EK h9 1 2 kg 32 14 34 3,3 1 22 11 17,2 4 16 4 4,3 12 25 12 2,23 5 21 45 4,3 16 27 14,5 22,36 63 21 51 4,3 16 32 18 25,55 8 25 65 4,3 2 36 22 3,9 1 25 75 6,3 2 41 22 32 1,45 125 37 97 6,3 3 5 3 42 2,7 16 43 122 6,3 35 55 36 46 4,3 2 43 122 6,3 35 6 38 49 6,1
ISO/VDMA Cylinder mountings For PA/181,.../M; PA/182,.../M; PA/183,.../M A/28,.../M; A/283,.../M; A/8,.../M; KA/8,.../M M/191,.../M; M/192,.../M; M/193,.../M; PVA/8/M Piston rod clevis F Front or rear detachable trunnion FH K L 1 CE LE CL CM TL D H11 TM h 14 CE G2 G3 ear hinge L G1 ear hinge UL VDMA 24562 Part 2 G1 H2 H2 CL KK UW TD e 9 E ø CK h 11 L 3 Thread KK CE Ø CK h11 CL CM E LE K kg M1x1,25 4 1 2 1 16 2 28,9 M12x1,25 48 12 24 12 19 24 32,13 M16x1,5 64 16 32 16 25 32 41,5,33 M2x1,5 8 2 4 2 32 4 5,67 M27x2 11 3 55 3 45 54 62 1,35 M36x2 144 35 7 35 57 72 95 3, M42x2 168 4 85 4 68 84 16 6,4 M48x2 192 5 96 5 85 96 121 8,7 Ø Ø D H11 L1 L3 ØTD e9 TL TM h14 UW1 kg 32 3 16 8 1 12 12 5 5,2 4 35 2 1 1,6 16 16 63 55,38 5 4 24 12 1,6 16 16 75 65,6 63 45 24 12 1,6 2 2 9 75 1,1 8 45 28 14 1,6 2 2 11 1 1,9 1 55 38 19 2 25 25 132 12 3,5 125 6 5 25 2 25 25 16 145 6,5 Front hinge M CA G1 K ear eye ISO 6431 and VDMA 24562 Part 2 EW L CD H 9 H2 L 1 Thread KK Ø CA CE Ø D G1 G2 G3 H2 K1 K2 L1 K Ø S kg M1x1,25 32 32 4 11 21 18 31 8 38 51 1,6 28 6,6,24 M12x1,25 4 36 48 11 24 22 35 1 41 54 1,6 32 6,6,33 M16x1,5 5 45 64 15 33 3 45 12 5 65 1,6 41,5 9,81 M16x1,5 63 5 64 15 37 35 5 12 52 67 1,6 41,5 9,83 M2x1,5 8 63 8 18 47 4 6 14 66 86 2,5 5 11 1,42 M2x1,5 1 71 8 18 55 5 7 15 76 96 2,5 5 11 1,87 M27x2 125 9 11 2 7 6 9 2 94 124 3,2 62 14 3,85 M36x2 16 115 144 2 97 88 126 25 118 156 4 95 14 9, M36x2 2 135 144 24 15 9 13 3 122 162 4 95 16 1,6 K1 K2 Ø Ø CD H9 EW L M kg 2 8 15,8 2 14 8,2 25 8 15,8 2 14 8,3 32 1 25,8 22 13 9,9 4 12 27,8 25 16 12,11 5 12 31,7 27 17 12,17 63 16 39,7 32 22 15,24 8 16 49,7 36 22 15,37 1 2 59,7 41 27 2,59 125 25 69,7 5 33 25 3,2 16 3 89,7 55 35,5 3 6,1 2 3 89,7 6 37 3 6,8 M CA K1 K2 LH G2 G3 L1 K1 K2 G2 G3 L1 Ø CA Ø D G1 G2 G3 H2 K1 K2 L1 LH Ø S L kg UL kg 32 32 32 11 22 21 18 31 8 38 51 1,6 52 6,6,16 2,39 4 36 36 11 25 24 22 35 1 41 54 1,6 6 6,6,23,47 5 45 45 15 27 33 3 45 12 5 65 1,6 68 9,36,82 63 5 5 15 32 37 35 5 12 52 67 1,6 79 9,52 1,14 8 63 63 18 36 47 4 6 14 66 86 2,5 99 11,82 1,93 1 71 71 18 41 55 5 7 15 76 96 2,5 119 11 1,32 2,85 125 9 9 2 5 7 6 9 2 94 124 3,2 139 14 5,4 5,8 16 115 115 2 55 97 88 126 25 118 156 4 181 14 1,6 1,7 2 135 135 24 6 15 9 13 3 122 162 4 181 18 14,1 15,2 25 165 33 7 128 11 16 35 15 2 2 218 22 32,4 32 2 4 8 15 122 186 4 17 234 2 238 26 52,5 Stainless steel, weight on request 77
Actuators ISO/VDMA Cylinder mountings For PA/181,.../M; PA/182,.../M; PA/183,.../M A/28,.../M; A/283,.../M; A/8,.../M; KA/8,.../M M/191,.../M; M/192,.../M; M/193,.../M; PVA/8/M Trunnion support S VDMA 24562 Part 2 3 Centre trunnion H (or tie rod types) ISO 6431 and VDMA 24562 Part 2 T 1 H 1 H7 1 F x 45 UW TD e 9 ø CN G 7 EM G 1 ø CK H 9 EM G 1 CA L 1 H 2 L 1 H 2 H 2 2 A B 1 B 2 C TL TM h 14 L Type UH Type H Grease nipple up to Ø 125 mm Ø A B1 B2 C Ø H7 Ø D2 Ø D3 x45 H1 H2 T1 kg 32 32 46 18 1,5 12 6,6 11 1 3 15 6,8,1 4 36 55 21 12 16 9 15 1,6 36 18 9,14 5 36 55 21 12 16 9 15 1,6 36 18 9,14 63 42 65 23 13 2 11 18 1,6 4 2 11,19 8 42 65 23 13 2 11 18 1,6 4 2 11,19 1 5 75 28,5 16 25 14 2 2 5 25 13,34 125 5 75 28,5 16 25 14 2 2 5 25 13,34 16 6 92 39 21,5 32 18 26 2,5 6 25 15,5 1,9 2 6 92 39 21,5 32 18 26 2,5 6 25 15,5 1,9 For use with mountings style H, FH and UH. Stainless steel, weight on request. Adjustable centre trunnion UH (or proile types) Ø L Ø TD e9 TL TM h14 UW XV XV kg Torque min. max. max. (Nm) 32 2 1 12 12 5 5 66 8,16 6 4 24 1,6 16 16 63 58 76 89,35 6 5 28 1,6 16 16 75 7 82 98,65 1 63 28 1,6 2 2 9 8 88 17,85 1 8 28 1,6 2 2 11 1 97 123 1,2 15 1 38 2 25 25 132 126 112 128 2,3 15 125 5 2 25 25 16 152 136 154 3,3 25 16 5 2,5 32 32 2 192 155 185 5,3 4 2 5 2,5 32 32 25 24 17 2 9,4 4 25 6 3,2 4 4 32 318 193 217 18, 32 7 3,2 5 5 4 4 215 245 3, Note: Style H : These mountings are only supplied assembled complete with the cylinder. Unless otherwise speciied, units will be supplied with dimension XV plus hal the stroke length. XV = Distance rom the piston rod shoulder to the centre o the mounting. Style UH : It is most important that the locking screws which secure the mounting to the tie rod are tightened to the torque igures shown in the table below. For maximum energy input, consult our Technical Service. XV min. XV max. + stroke UW ø TD e 9 L Locking screws TL TM h 14 Ø L Ø TD e9 TL TM h14 UW kg Torque max. (Nm) 32 25 1 12 12 5 58,35 2, 4 28 1,6 16 16 63 65,5 3,5 5 28 1,6 16 16 75 8,8 3,5 63 36 1,6 2 2 9 96 1,4 5, 8 36 1,6 2 2 11 116 1,9 6, 1 48 2 25 25 132 14 2,3 6, 125 5 2 25 25 16 163 3,3 6, Narrow hinge SS Wide hinge SW Swivel hinge US EN -,1 CA ø CN H 7 EU E G 1 L 1 H 2 G 2 G 2 G 2 K 1 G 3 K 1 G 3 K 1 G 3 K 2 K 2 K 2 Ø CA Ø Ø H2 EM EM1 EN-,1 E EU G1 G2 G3 H6 K1 K2 L1 1 Ø S CN H7 CK H9 D 32 32 1 1 11 8 26 1 14 16 1,5 21 18 31 8 38 51 1,6 1 6,6 13 4 36 12 12 11 1 28 12 16 18 12 24 22 35 1 41 54 1,6 11 6,6 13 5 45 16 12 15 12 32 16 21 21 15 33 3 45 1 5 65 1,6 13 9 13 63 5 16 16 15 12 4 16 21 23 15 37 35 5 12 52 67 1,6 15 9 15 8 63 2 16 18 14 5 2 25 28 18 47 4 6 14 66 86 2,5 15 11 15 1 71 2 2 18 15 6 2 25 3 18 55 5 7 15 76 96 2,5 19 11 15 125 9 3 25 2 2 7 3 37 4 25 7 6 9 2 94 124 22 14 15 16 9 35 43 44 28 97 88 126 25 118 156 4 31 14 15 2 9 35 43 47 28 15 9 13 3 122 162 4 31 16 15 25 11 128 11 16 35 15 2 2 4 22 32 12 15 122 186 4 17 234 2 45 26 78 SW SS US kg kg kg,5,15,19,7,2,24,14,48,46,18,5,59,28,75 1,3 1,42 1,2 1,4 2,7 2,5 3,1 6,3 6, 6,4 8, 7,6 9,1 13,4 22,
3 ISO/VDMA Cylinder mountings For PA/181,.../M; PA/182,.../M; PA/183,.../M A/28,.../M; A/283,.../M; A/8,.../M; KA/8,.../M M/191,.../M; M/192,.../M; M/193,.../M; PVA/8/M Universal piston rod eye UF DIN ISO 8139 CE Universal rear eye U EN CN H 7 EN -,1 KK CN H 7 E LE AX E Thread KK AX CE Ø CNH7 EN-,1 E LE kg M1x1,25 2 43 1 14 14 15 13,9 M12x1,25 22 5 12 16 16 17 13,13 M16x1,5 28 64 16 21 21 22 15,33 M2x1,5 33 77 2 25 25 26 15,67 M27x2 51 11 3 37 35 36 15 1,35 M36x2 56 125 35 43 4 41 16 3, M42x2 6 142 4 49 45 46 17 6,4 M48x2 65 16 5 6 58 59 12 8,7 Ø Ø CN H7 EN E kg 32 1 14 16 22 14,5 13,15 4 12 16 19 25 18 13,25 5 16 21 21 27 19 13,4 63 16 21 24 32 24 15,55 8 2 25 28 36 24 15,9 1 2 25 3 41 29 15 1,5 125 3 37 4 5 36 15 2,7 16 35 43 44 55 41 16 4,6 2 35 43 48 6 42 16 7,3 QM/27/2/1 Switch mounting brackets Switches: M/5, QM/34 and QM/134 (Ø 8 mm) Ø A B kg 32 9 7,1 4 8 8,1 5 7 5,1 63 7 7,1 8 7 4,1 1 2 2,1 125-4 -3,1 16-1 -9,1 2-17 -14,1 12 Switch mounting bracket Magnetically operated switch A B QM/31//22 Switch mounting brackets Switches: QM/31, QM/32 and QM/132 Ø A B kg 32 4,5 38,3 4 5,5 43,3 5 4,5 48,3 63 4,5 53,3 8 1,5 61,3 1,5 68,3 125-1 79,3 16 91,5,3 2-4 16,3 25-3 138,4 32-21 154,8 Switch mounting bracket Magnetically operated switch A B QM/14/1/22 Bracket with holding strap Switch: QM/14 Ø A kg 32 31,5,2 4 3,5,2 5 31,5,2 63 29,5,2 8 3,5,2 1 3,2 2 1 Switch mounting bracket Pneumatic switch Holding strap A 79