Update Alert: Firmware updates are posted to the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide Index Vehicle Application Guide... 02 Installation Types A: Please refer to page 2 for vehicle compatibility with this installation type... 03 B: Please refer to page 2 for vehicle compatibility with this installation type... 05 C: Please refer to page 2 for vehicle compatibility with this installation type... 07 Programming Module Programming... 09 Features & Options List... 0 Module Reset... 0 LED Diagnostics... Warranty... 2 TECHNICAL SUPPORT / INFORMATION web resources: www.xpresskit.com www.xpressvip.com www.directechs.com
Page 2 Vehicle Application Guide & Installation type Vehicle Application Guide 200 2009 2008 2007 2006 PK- Bypass Transponder Data: NKR Lexus ES350(PTS) C C C C W2W D2D Pontiac Vibe (Key) A A W2W D2D Scion xb (Key)** A A W2W D2D xd (Key)** A A W2W D2D Toyota Camry(Key) A A A A W2W D2D Camry (PTS) C C C W2W D2D Camry Hybrid (PTS)* C C C W2W D2D Corolla (Key) A A W2W D2D Corolla (PTS) B B W2W D2D Highlander (Key) A A A W2W D2D Highlander (PTS) C C C W2W D2D Highlander Hybrid (PTS)* C C C W2W D2D Matrix (Key) A A W2W D2D Rav(Key) A A A A A W2W D2D Rav (PTS) B B W2W D2D Sequoia (Key) A A A W2W D2D Tundra(Key) A A A A W2W D2D Yaris (Key) A A A A A W2W D2D NOTE: Keyless and smart-key will remain functional during remote start. *By default, the tach is set to 000 rpm on hybrid vehicles. ** If there is no immobilizer on Scion xb and xd the module will not work (that also includes door lock controls). DL- Door Lock Control DL- Door Unlock ALL doors DL- Door Unlock Driver Priority DL- Arm Factory Security DL- Disarm Factory Security DL- Trunk / Hatch Release SS- Entry Status Front Door Pins SS- Entry Status ALL Door Pins SS- Entry Status Hood Pin SS- Entry Status Trunk/Hatch Pin SS- Entry Status Drivers Door Pin SS- Detect Factory Alarm Trigger RS- Tach Output RS - RPM Status RS - Ignition Status RS- Brake Status RS- Accessory Activation RS - Ignition Activation RS- Crank (Start) Activation RS- Hand-Brake Status Legend: PTS: Vehicle equipped with push-to-start Key: Vehicle not equipped with push-to-start D2D: Data-to-Data (D2D) only W2W: Wire-to-Wire (W2W) only : D2D and W2W Categories Legend: PK: Transponder DL: Door Lock SS: Security System RS: Remote Starter
Remote Starter Platform: CANMAX00 Page 3 Install Type A See page for help on locating key components in the vehicle and wiring reference chart. off This connection not required if the vehicle is not equipped with autolight feature. White (wire side view) At headlight switch Black connector at immobilizer (wire side view) Relay pin 30 Cut Relay pin 87a (-) pin 9 0 9 8 7 6 5 3 2 20 9 8 7 6 5 3 2 7 6 5 3 2 87 85 RX pin TX pin 5 (+) 2v 86 87a 30 (-) Rearm Output Standard connections from remote starter to vehicle are required. (-) Hood Status Input (-) Trunk Status Input (-) Door Status Input (AC) Tach Input (+) Brake Input (-) Handbrake status Input (-) GWR (Status) Output (-) Lock Output (-) Unlock Output (-) Trunk Output (+) 2V Input (-) Ground Input (+) 2V Output D2D connector is not required when installed P#: XKD2D65 in W2W mode. The wire colors of the D2D harness depend on the kit you have purchased. 2 Programming Button :Black: (-) Ground 2:Red: (+) 2V 7:Red/White: (-) Trunk Input 8:Blue: (-) Unlock Input 9:Green: (-) Lock Input :Pink: (+) Ignition Input 2:Blue/White: (-) GWR (Status) Input 3:Tan: CAN Low :Tan/Black: CAN High 5:Black/White: (-) Handbrake Status Output TX (-) Ground RX (+) 2V :Violet/White: (AC) Tach Output* 2:Green: (-) Door Status Output 3:Gray: (-) Trunk Status Output :Blue/Red: (-) Hood Status Output XK-00X 20 8:Pink: (+) Ignition Status Output 3:Yellow/Black: TX :Violet/White: RX 5:Red/White: (+) Brake Status Can High pin 6 Not required in D2D mode. * See features #2 to activate/deactivate Tach Output. The Tach wire is an optional connection required on some remote starters not supporting tach signal in D2D. 8 9 Diagnostic connector OBDII (wire side view) 6 Can Low pin The order of the wires is not representative of reality.
Page Install Type A Wiring reference chart Pontiac Vibe (Key) 2009-200 Scion xb (Key) 2009-200 Scion xd (Key) 2009-200 Toyota Camry (Key) 2007-200 Toyota Corolla (Key) 2009-200 Toyota Highlander (Key) 2007-200 Toyota Matrix (Key) 2009-200 Toyota Rav (Key) 2006-200 Toyota Sequoia (Key) 2008-200 Toyota Tundra (Key) 2007-200 Toyota Yaris (Key) 2006-200 Wire function Connector Pin position Wire color CAN High Diagnostic connector 6 Light Green CAN Low Diagnostic connector White RX Key transponder amplifier Light Blue TX Key transponder amplifier 5 Beige CAN High C at Diagnostic connector 6 Light Green CAN Low C at Diagnostic connector White RX at Immobilizer Light Blue TX at Immobilizer 5 Beige CAN High F6 at Diagnostic connector 6 Violet CAN Low F6 at Diagnostic connector White RX 7-pin conn. at Immobilizer Green TX 7-pin conn. at Immobilizer 5 Violet CAN High E0 at Diagnostic connector 6 Black CAN Low E0 at Diagnostic connector White E2at headlight switch 9 Green RX E25 at Immobilizer Brown TX E25 at Immobilizer 5 Red CAN High E at Diagnostic connector 6 Light Green CAN Low E at Diagnostic connector White RX E29atimmobilizer LightblueorPink TX E29at immobilizer 5 Beige or Green CAN High D7 at Diagnostic connector 6 Blue CAN Low D7 at Diagnostic connector White D3 at headlight switch 9 Green RX D27at immobilizer Red TX D27atimmobilizer 5 Lightblue CAN High E5 at Diagnostic connector 6 Light Green CAN Low E5 at Diagnostic connector White RX E7atimmobilizer Lightblue TX E7at immobilizer 5 Beige CAN High E3 at Diagnostic connector 6 Black CAN Low E3 at Diagnostic connector White E2at headlight switch 9 Green RX E5 at immobilizer Pink TX E5 at immobilizer 5 Green CAN High H9 at Diagnostic connector 6 Violet CAN Low H9 at Diagnostic connector White H at headlight switch 9 Green or pink RX H27atimmobilizer LightGreen TX H27 at immobilizer 5 Blue CAN High J7 at Diagnostic connector 6 Violet CAN Low J7 at Diagnostic connector White J0 at headlight switch 9 Green RX J20atimmobilizer Lightgreen TX J20 at immobilizer 5 Blue CAN High D5at Diagnostic connector 6 Violet CAN Low D5 at Diagnostic connector White RX D2at immobilizer Green TX D2 at immobilizer 5 Violet WARNING - No take over feature is available on Push-to-start vehicle. The engine will stop when a door is open. - To remote start the engine, all doors must be closed. Locating key components in the vehicle Main Body ECU
Remote Starter Platform: CANMAX00 Page 5 Install Type B See page 6 for help on locating key components in the vehicle and wiring reference chart. off This connection is required for the Toyota RAV (PTS) 2009-200 only. Relay pin 30 Cut Relay pin 87a (-) pin 8 White (wire side view) Back side on Main body ECU 5 6 7 8 9 8 9 0 2 3 2 3 5 6 7 (+) STSW** pin White at Fuse Box +2v Black pin Can High pin 6 Diagnostic connector OBDII (wire side view) 8 9 6 Can Low pin 87 85 (+) 2v 86 87a 30 (-) Rearm Output (-) Hood Status Input (-) Trunk Status Input (-) Door Status Input (AC) Tach Input Do not connect any other accessories, ignitions or starts wire from the remote starter to the vehicle. The interface module is handling the required vehicle power and start sequence from the push-to-start button circuit. (+) Brake Input (-) Handbrake status Input (-) GWR (Status) Output (+) Ignition Input (+) Starter Output (-) Lock Output (-) Unlock Output (-) Trunk Output (+) 2V Input (-) Ground Input D2D connector is not required when installed P#: XKD2D65 in W2W mode. The wire colors of the D2D harness depend on the kit you have purchased. TX (-) Ground RX (+) 2V :Violet/White: (AC) Tach Output* 2:Green: (-) Door Status Output 3:Gray: (-) Trunk Status Output :Blue/Red: (-) Hood Status Output XK-00X 2 20 Programming Button :Black: (-) Ground 2:Red: (+) 2V 7:Red/White: (-) Trunk Input 8:Blue: (-) Unlock Input 9:Green: (-) Lock Input 0:Violet: (+) Starter Input :Pink: (+) Ignition Input 2:Blue/White: (-) GWR (Status) Output 3:Tan: CAN Low :Tan/Black: CAN High 5:Black/White: (-) Handbrake Status Output 6:Green/Black: (-) Push-to-Start Output 8:Pink: (+) Ignition Status Output 5:Red/White: (+) Brake Status 8:Brown: (+) 2V Input 9:Yellow: (+) STSW** Output (-) Push-to-start Not required in D2D mode. * See features #2 to activate/deactivate Tach Output. The Tach wire is an optional connection required on some remote starters not supporting tach signal in D2D. ** STSW: Starter switch Black ENGINE START 2 3 5 6 STOP connector 7 8 9 0 2 3 Connection required only if Pit-Stop / idle mode is desired (see details on the next page). The order of the wires is not representative of reality.
Install Type B Toyota Corolla (PTS) 2009-200 Toyota RAV (PTS) 2009-200 *STSW:StarterSwitch Pit-Stop / Idle Mode The Pit-Stop/Idle feature allows the vehicle to remain running after leaving the vehicle. Refer to the owner's guide of your remote starter for more details. Wiring reference chart Wire function Connector Pin position Wire color CAN High Diagnostic Conn. 6 Light Green CAN Low Diagnostic Conn. White Push-to-start at PTS button 7 White STSW* E52 at ECU Black or White 2V 2G at fuse box White CAN High Diagnostic Conn. 6 Black CAN Low Diagnostic Conn. White E7at ECU 8 Green Push-to-start at PTS button 7 White STSW* E7 at ECU Red 2V IG at fusebox White WARNING - No take over feature is available on Push-to-start vehicle. The engine will stop when a door is open. - To remote start the engine, all doors must be closed. Locating key components in the vehicle Page 6 Main Body ECU
Remote Starter Platform: CANMAX00 Page 7 Install Type C See page 8 for help on locating key components in the vehicle and wiring reference chart. White (wire side view) At main body ECU White (wire side view) At main body ECU Can High pin 6 6 5 3 2 2 8 Relay pin 30 off Cut Relay pin 87a 7 6 5 3 2 0 9 7 26 25 2 23 22 2 20 9 8 (-) pin 2 8 White at Fuse Box 6 0 5 9 3 8 7 (+) STSW** pin Diagnostic connector OBDII (wire side view) 9 6 Can Low pin (+) 2v 86 87 87a 30 85 (-) Rearm Output +2v Black pin (-) Hood Status Input (-) Trunk Status Input (-) Door Status Input (AC) Tach Input Do not connect any other accessories, ignitions or starts wire from the remote starter to the vehicle. The interface module is handling the required vehicle power and start sequence from the push-to-start button circuit. (+) Brake Input (-) Handbrake status Input (-) GWR (Status) Output (+) Ignition Input (+) Starter Output (-) Lock Output (-) Unlock Output (-) Trunk Output (+) 2V Input (-) Ground Input D2D connector is not required when installed P#: XKD2D65 in W2W mode. The wire colors of the D2D harness depend on the kit you have purchased. TX (-) Ground RX (+) 2V :Violet/White: (AC) Tach Output* 2:Green: (-) Door Status Output 3:Gray: (-) Trunk Status Output :Blue/Red: (-) Hood Status Output XK-00X 2 20 Programming Button :Black: (-) Ground 2:Red: (+) 2V 7:Red/White: (-) Trunk Input 8:Blue: (-) Unlock Input 9:Green: (-) Lock Input 0:Violet: (+) Starter Input :Pink: (+) Ignition Input 2:Blue/White: (-) GWR (Status) Output 3:Tan: CAN Low :Tan/Black: CAN High 5:Black/White: (-) Handbrake Status Output 6:Green/Black: (-) Push-to-Start Output 8:Pink: (+) Ignition Status Output 5:Red/White: (+) Brake Status 8:Brown: (+) 2V Input 9:Yellow: (+) STSW** Output (-) Push-to-start Not required in D2D mode. * See features #2 to activate/deactivate Tach Output. The Tach wire is an optional connection required on some remote starters not supporting tach signal in D2D. ** STSW: Starter switch Black ENGINE START 2 3 5 6 STOP connector 7 8 9 0 2 3 Connection required only if Pit-Stop / idle mode is desired (see details on the next page). The order of the wires is not representative of reality.
Install Type C Lexus ES350 (PTS) 2007-200 Toyota Camry (PTS) 2007-200 Toyota Camry Hybrid (PTS) 2007-200 Toyota Highlander (PTS) 2008-200 Toyota Highlander Hybrid (PTS) 2008-200 *STSW:StarterSwitch Wiring reference chart Wire function Connector Pin position Wire color CAN High Diagnostic Conn. 6 Light Green CAN Low Diagnostic Conn. Pink E6at ECU 2 Yellow Push-to-start at PTS button 7 Blue STSW* E58 at ECU Red 2V DA at fuse box White CAN High Diagnostic Conn. 6 Black CAN Low Diagnostic Conn. White E7 at ECU 2 Green Push-to-start at PTS button 7 Blue STSW* E9 at ECU Gray 2V IA at fuse box Black CAN High Diagnostic Conn. 6 Black CAN Low Diagnostic Conn. White E7 at ECU 2 Green Push-to-start at PTS button 7 Blue STSW* E9 at ECU Gray 2V IA at fuse box Black CAN High Diagnostic Conn. 6 Blue CAN Low Diagnostic Conn. White D8 at ECU 2 Green Push-to-start at PTS button 7 Pink STSW* D0 at ECU Pink 2V IA at fuse box Black CAN High Diagnostic Conn. 6 Black CAN Low Diagnostic Conn. White D8 at ECU 2 Green Push-to-start at PTS button 7 Pink STSW* D0 at ECU Yellow 2V IA at fuse box Black Locating key components in the vehicle Pit-Stop / Idle Mode The Pit-Stop/Idle feature allows the vehicle to remain running after leaving the vehicle. Refer to the owner's guide of your remote starter for more details. WARNING - No take over feature is available on Push-to-start vehicle. The engine will stop when a door is open. - To remote start the engine, all doors must be closed. Page 8 Main Body ECU
Page 9 Module Programming Please Note: When a CANMAX00 is used in D2D with either Viper, Clifford or Python, the jumpers on the remote starter MUST be placed in the Horizontal operating position. Jumper position Connect the 20-pin harness. Caution! The 20 pin connector can be easily plugged in backwards. If connected in D2D Connect pin D2D harness & then 2 PIN. (This connection order is important.) 2 If connected in W2W Connect 2 PIN harness. Installation Type A: Module programming for vehicle with key. 3 When all connections are correctly done, the red LED will turn ON. Insert the key in the ignition switch. The red LED will flash slowly to indicate the key is in learning mode. 5 6 When the LED turns orange, turn the ignition ON. The green LED turns ON for 3 seconds and shuts off. Remove the key from ignition. KEY OFF IGN START & Orange 3 sec. & & FLASH KEY KEY OFF OFF ACC ON ACC ON Installation Type B&C:Module programming for vehicle with push-to-start. 3 5 The When all connections are correctly done, the red LED will turn ON. Make sure the key is in the vehicle. Press the push-to-start button twice to the ON position. green LED turns ON for 3 seconds and shuts off. The module is now programmed, press once again to OFF position. 3 sec. ENGINE START STOP ENGINE START STOP PUSH 2X PUSH X
Feature Programming To enter feature programming routine - Press the Push-to-Start (PTS) button twice to turn the ignition ON, then press the button once to turn it OFF. - Within 5 sec, press and HOLD the integrated programming button (IPB). The orange LED turns ON after 3 seconds. Release the IPB. - The green LED starts flashing slowly one time to indicate the feature number is. After a short delay, the red LED flashes rapidly one time to indicate the current option of feature. It repeats until next action happens. Changing feature options - Press the lock/arm or unlock/disarm button on aftermarket transmitter to change the option of the selected feature. - The red LED flashes rapidly the number of times equal to the current option number. After a short delay, the green LED flashes slowly the number of times to indicate the current feature. It repeats until next action happens. Accessing another feature - Press and release the IPB a number of times to advance from the current feature to the next desired feature. - The green LED flashes slowly the number of times equal to the feature number. After a short delay, the red LED flashes rapidly one time to indicate the current option of the current feature. It repeats until next action happens. When the maximum number of feature or option is reached, the will LED starts flashing again from the first feature or option. Once a feature is programmed - Another feature(s) can be programmed. - The feature programming can be exited. Exiting feature programming - No activity for 30 seconds; after 30 seconds, the orange LED will turn ON for 2 seconds to confirm exiting. OR - Press and HOLD the IPB for 3 seconds. After 3 seconds, the orange LED will turn ON for 2 seconds to confirm exiting. Integrated Programming Button (IPB) Page 0 Feature and Option List Features Operation Option *Default Option RF output type Activate this feature whenever an external RFTD module is used (i.e.: XL20 or XL202) 2 Tach Output (W2W only) Resetting the Module 2 Connect the 20-pin harness. No RF Output* RFTD Output Disabled Enabled* Press and hold the Programming button, then powerup the module: - D2D: connect the D2D cable; or, - W2W: connect the 2-pin harness. & OR 3 When the LED turns ON orange, release the Programming button. Once the LED turns ON red, the module reset is complete. & & Solid Orange Solid Red
Page LED Diagnostics & Troubleshooting LED Status Description Troubleshooting Programming the Module Solid red ((( ))) (( )) Flashes red (rapidly) Flashes red (slowly) Solid orange Waiting on the completion of a programming sequence, or the ignition is turned on. Vehicle has been detected and is waiting for the programming sequence. The key has been detected and is in learning process. The module is waiting ignition ON. This can also mean there is an issue with the data bus wiring. Make sure the connections to the data bus are correct by referring to the wiring diagram. This can also mean there is an issue with the bypass wiring. Make sure the connections to the bypass are correct by referring to the wiring diagram. N/A If ignition is ON and the LED stay orange, this can also mean there is an issue with the CAN wires. Refer to the wiring diagram to make the right connections. Solid green x3 Module has been successfully N/A seconds programmed. Off Module has no power. Make sure the D2D harness is connected or that the 2 Volt is present between the red and black wires. If the 2 Volt is present, the module may be defective. Remote Starting the Vehicle Flashes green Module is operating correctly. N/A (( )) Off N/A The Ground While Running (status) wire is incorrectly connected. Refer to the wiring diagram to make the right connections. While the Ignition is Turned Off Flashes green x Lock feature. This can also mean there is an issue with the wiring. (( )) Refer to the wiring diagram to make the right X connections. (( )) Flashes green 2x Unlock feature. This can also mean there is an issue with the wiring. Refer to the wiring diagram to make the right 2X connections. Flashes green 3x Trunk release feature. This can also mean there is an issue with the wiring. (( )) Refer to the wiring diagram to make the right connections. 3X
Page 2 Limited One-Year Consumer Warranty For a period of ONE YEAR from the date of purchase of a Directed Electronics remote start or security product, Directed Electronics. ( DIRECTED ) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, the security or remote start accessory piece (hereinafter the Part ), which proves to be defective in workmanship or material under normal use, provided the following conditions are met: the Part was purchased from an authorized DIRECTED dealer; and the Part is returned to DIRECTED, postage prepaid, along with a clear, legible copy of the receipt or bill of sale bearing the following information: consumer s name, address, telephone number, the authorized licensed dealer s name and complete product and Part description. This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to its intended purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defect in materials or construction. TO THE MAXIMUM EXTENT ALLOWED BY LAW, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NON INFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING DEALERS OR INSTALLERS. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALLAPPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER S PURCHASE PRICE OF THE PART. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR AT DIRECTED S OPTION THE PART AS DESCRIBED ABOVE. Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights and you may also have other rights that vary from State to State. DIRECTED does not and has not authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this Part.920-0007 07-06 This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the select vehicle list upon completion of compatibility testing. Visit website for latest vehicle application guide. DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for any consequential damages sustained in connection with the part(s) installation. The manufacturer and it s distributors will not, nor will they authorize any representative or any other individual to assume obligation or liability in relation to the interface kit / data bus interface part(s) other than its replacement. N.B.:Under no circumstances shall the manufacturer and distributors of this product be liable for consequential damages sustained in connection with this product and neither assumes nor authorizes any representative or other person to assume for it any obligation or liability other than the replacement of this product only. PROTECTED BY U.S. PATENTS: 5,79,55; 6,0,60 B *;6,23,00 B; 6,29,26 B; 6,275,7 B; 6,297,73 B; 6,36,876 B; 6,392,53 B; 6,529,2 B2; 6,696,927 B2; 6,756,885 B; 6,756,886 B2; 6,77,67 B; 6,82,829 B; 6,92,750 B; 7,00,02 B; 7,05,830 B; 7,03,826 B; 7, 06,26 B; 7,06,37 B; 7,068,53 B; 7,205,679 B; CDN.PATENT: 2,320,28; 2,,99; 2,5,0; 2,5,023; 2,5,027; 2,5,038; 2,5,0; 2, 20, 97; 2,26,670; 2,5,089 EUROPEAN PATENT:,053,28 PAT.PENDING: 2,29,306; MADE IN CANADA