Compact acuum Ejector Series ZA Total length Total width 7.9 mm 9.9 mm Total height. mm Response time 0 ms Response time for up to 0 ka Nozzle diameter: ø0.7 iping: ø/ø. x 0 mm Able to install on the moving parts Shortened tube length to pad makes the response time improved. 0 Weight g ossible to be mounted on moving parts thanks to lightweight Normally closed Available with or without pressure sensor kinds of pressure range are selectable. 0 to ka 0 to 0 ka Supply pilot valve Normally closed Latching Suction filter Nominal filtration rating: 0 µm A
Compact acuum Ejector Series ZA Ejector Unit How to Order ZA 07 K L 0 Nozzle nominal size 0 0. 07 0.7 Solenoid valve combination (Refer to Table ().) Symbol K J N N Normally closed Normally closed Latching positive common Latching positive common Latching negative common Latching negative common Normally closed None Normally closed None Normally closed None ilot valve (Refer to Table ().) Y Standard ( W for DC) Note) DC low wattage type (0. W) Note) Note) Avoid energizing the solenoid valve for long periods of time. (Refer to Design and Selection on Specific roduct recautions.) ower supply voltage (Refer to Table ().) L LO M MO G 0 AC (0/0 Hz) 00 AC (0/0 Hz) AC (0/0 Hz) 0 AC (0/0 Hz) DC DC Electrical entry L plug connector, with 0. m lead wire, with light/surge voltage suppressor L plug connector, without connector, with light/surge voltage suppressor M plug connector, with 0. m lead wire, with light/surge voltage suppressor M plug connector, without connector, with light/surge voltage suppressor Grommet, with 0. m lead wire (Not available for latching and AC types.) Table () Combination of Solenoid alve, ilot alve and ower Supply oltage Combination no. q w e r t y u i Solenoid valve combination symbol K K J J N N ilot valve symbol Y Y Combinations () to (8) in the above table are the only possible options. Manual override Applicable power supply voltage () 0 AC 00 AC AC 0 AC DC DC supply () port Symbol 0 M Symbol Applicable tubing O.D. Without fitting (M x 0.) (Straight) (Elbow) Without supply adapter Note) (For manifold) Note) O-ring and round head combination screws AC0090 (M x ) are attached to the supply adapter (M). ressure sensor specifications Symbol Rated pressure range and accuracy art no. With pressure sensor (0 to ka, accuracy ±% F.S.) SE A With pressure sensor (0 to ka, accuracy ±% F.S.) SEA With pressure sensor ( 0 to 0 ka, accuracy ±% F.S.) SE A With pressure sensor ( 0 to 0 ka, accuracy ±% F.S.) SEA Note ) Without pressure sensor K-0 Note ) One-touch fittings are plugged when the pressure sensor is mounted. Note ) This pressure switch detects pressure and converts the data into analog output. When the product is used as a vacuum switch, a pressure sensor controller Series SE00 (CAT.ES0-) is necessary. Suction filter F Applicable tubing O.D.. (Straight) (Straight). (Elbow) (Elbow) Without suction filter With suction filter Non-locking push type (Tool required) Latching type: ush-locking type (Tool required) Locking type (Tool required) Note) Latching type (supply valve) has the push-locking type only, but either the push type or the locking type can be selected for the release valve. Warning The filter case of this suction filter is made of nylon. The product will be damaged if solvents such as alcohol or chemicals are splashed on it. Avoid using it in an atmosphere where such solvents are present. This suction filter is exclusive to Series ZA. Do not use for other purposes.
Compact acuum Ejector Series ZA How to Order Manifold ZZA 08 Number of stations 0 station 0 stations... Maximum Simultaneous Opreating Stations Manifold model Ejector nozzle diameter ø0. ø0.7 - ZZA Stations - - ZZA Stations - stations stations stations ZZA Stations ZZA Stations ZZA Stations ZZA Stations - - - - stations stations stations stations 08... Right common air pressure supply () port (viewed from the vacuum () port side) Symbol 0 Applicable tubing O.D. Without fitting (M x 0.8) (Straight) (Straight) (Elbow) (Elbow) With plug Left common air pressure supply () port (viewed from the vacuum () port side) Symbol 0 Applicable tubing O.D. Without fitting (M x 0.8) (Straight) (Straight) (Elbow) (Elbow) With plug Manifold Ordering Example Flow / Exhaust Characteristics (Representative values) ZZA8- pc. ZA7-KL-F-M pcs. (Stations to ) ZA-L-F-M pcs. (Stations to 7) ZA- pc. (Station 8) lanking plate assembly Note) The stations are sequentially numbered. When viewed from the side of the vacuum ports, the far left station is designated as station. ZA0 Exhaust Characteristics acuum pressure (ka) 80 70 0 0 0 0 0 acuum pressure Air consumption Suction flow 0 0 0 Suction flow (L/min(ANR)) Air consumption (L/min(ANR)) ZA0 Flow Characteristics acuum pressure (ka) Supply pressure: 0. Ma 80 0 0 0 Left 7 8 ZA7-KL-F-M ZA-L-F-M ZA- lanking plate assembly art no.: ZA- Right acuum pressure (ka) 80 70 0 0 0 0 0 0 0. 0. 0. 0. 0. 0. 0 8 Supply pressure (Ma) Suction flow (L/min(ANR)) ZA07 Exhaust Characteristics acuum pressure Air consumption Suction flow 0 0 0 Suction flow (L/min(ANR)) Air consumption (L/min(ANR)) ZA07 Flow Characteristics acuum pressure (ka) Supply pressure: 0. Ma 80 0 0 0 0 0. 0. 0. 0. 0. 0. 0 8 Supply pressure (Ma) Suction flow (L/min(ANR)) C
Series ZA Specifications General Specifications Maximum operating pressure Minimum operating pressure Operating temperature range Fluid ibration resistance Note) Ejector Nozzle nominal diameter Standard supply pressure Note) Maximum vacuum pressure Note) Maximum suction flow Air consumption 0.0 Ma 0.0 Ma to 0 C (No condensation) Air 0 m/s Note) There was no malfunction confirmed when tested under the following conditions: From to 00 to Hz and whichever of the following is smaller:. mm amplitude or 98 m/s acceleration in X, Y, Z direction for hours each. (initial value) 0. mm 0.0 Ma 7 ka L/min (ANR) L/min (ANR) 0.7 mm 0. Ma 78 ka 8 L/min (ANR) 8 L/min (ANR) Note) The maximum vacuum pressure was determined by applying the standard supply pressure. Different supply pressures are required to determine a model. Weight Single unit With pressure sensor Without pressure sensor Manifold base station stations stations stations stations stations 7 stations 0 g g 9 g g g g 7 g 9 g g g Calculation of weight for the manifold type (Single unit weight) x (Number of stations) + (Manifold base) Example) stations manifold with pressure sensors 0 (g) x + 7 (g) = 7 (g) ressure Sensor Model SE SEA SE SEA Rated pressure range 0 to ka 0 to 0 ka roof pressure Fluid Output voltage Output impedance ower supply Current consumption 00 ka Air Analog output to (within rated pressure range), 0. to (within extension analog output range) Approx. kω to DC ±, Ripple (p-p) % or less (with power supply polarity protection) ma or less Accuracy (Ambient temperature C) ±% F.S. (within rated pressure range) ±% F.S. (within rated pressure range) ±% F.S. (within rated pressure range) ±% F.S. (within rated pressure range) Linearity Repeatability Temperature characteristics Operating humidity range Withstand voltage Insulation resistance Sensor cable ±0.% F.S. ±0.% F.S. Effects to the output value due to supply voltage: ±0.8% F.S. ±% F.S. (based on C) Operating/Stored: to 8% RH (No condensation) 00 AC or more, 0/0 Hz for minute between terminals and housing 0 MΩ or more (00 DC measured via megohmmeter) between terminals and housing Oilproof heavy-duty vinyl cable (ellipse), cores,.7 x., m, Conductor area: 0. mm, Insulator O.D.: 0.9 mm
Compact acuum Ejector Series ZA Construction i r o Component arts Description No. ody alve cover oppet valve assembly Release flow adjusting needle assembly Supply adapter Material T T w e t u! q! y!0 Replacement arts Description No. 7 8 9 Sound absorbing material Round head combination screw ressure sensor O-ring Filter element art no. ZA-SAE AC0090 (M x ) - - SE -R0 KA0077 ZA-FE-0 For above parts of No. 7 and No., the parts assembly ZA-O- ( pcs each) is available. Solenoid alve Y L N ilot valve Standard ( W) Low wattage type (0. W) Not applicable to AC type. Latching positive common Latching negative common Rated coil voltage 0 AC 00 AC AC 0 AC DC DC ressure Sensor SE L LO M MO G L R0 How to Order Solenoid valve connector assembly part no. Manual override Non-locking push type (Tool required) Latching type: ush-locking type (Tool required) Locking type (Tool required) Note) Latching manual override: ush-locking type only Electrical entry L plug connector, with 0. m lead wire L plug connector, without connector, with light/surge voltage suppressor M plug connector, with 0. m lead wire M plug connector, without connector, with light/surge voltage suppressor Grommet, with 0. m lead wire (Not available for latching and AC types.) How to order connector assembly DC Single AXT-A- DC positive common Latching AXT-A- DC negative common Latching AXT-AN- 0 AC Single AXT-A- Latching AXT-A- 00 AC Single AXT-A- Latching AXT-A- Connector, socket ( pcs) only AXT-A Lead wire length 0 0 00 mm 00 mm 00 mm 000 mm 000 mm Lead-wire length of the plug connector The lead-wire length for a valve with a lead-wire is 00 mm. When in need of a valve with a lead-wire longer than 00 mm, place an order for a valve without a connector and connector assembly. Rated pressure range 0 to ka 0 to 0 ka Accuracy A ±% F.S. or less ±% F.S. or less C
Series ZA supply () port Dimensions Release flow adjusting needle lug Type K ZA K 7 77 ZA K Locking type manual override ZA K F Circuit diagram supply () port M. 7. 9 Supply adapter. ZA K L F 0 (000) Suction filter x ø.7 (Mounting hole) 9.9 Note) When the body is mounted, tighten with a torque of 0. ± 0.0 N m. Using excessive torque may cause damage to the body.. Locking type manual override Locking type manual override. ZA K M ZA K G Dimensions of the vacuum () and air pressure supply () port fittings after installation Dimensions after the fittings are installed on the vacuum () port, and air pressure supply () port of a single unit are shown below. KS-MN 9. KS0-MN KL-MN. KL0-MN... ø7....8 9. ZA K ZA K ZA K ZA K Dimensions of the vacuum () port fittings after installation..7. KS0-MG KL0-MG.. ZA K ZA K C Dimensions of the air pressure supply () port fittings after installation
supply () port Compact acuum Ejector Series ZA Dimensions Release flow adjusting needle lug Type J ZA J 7 77 ZA J supply () port M. 7. (000) 9 ZA J F Supply adapter. Suction filter x ø.7 (Mounting hole) 9.9 Circuit diagram ZA J L F 0 Note) When the body is mounted, tighten with a torque of 0. ± 0.0 N m. Using excessive torque may cause damage to the body. ZA J M ZA J G Dimensions of the vacuum () and air pressure supply () port fittings after installation Dimensions after the fittings are installed on the vacuum () port, and air pressure supply () port of a single unit are shown below. KS-MN 9. KS0-MN KL-MN. KL0-MN... ø7....8 9. ZA J ZA J ZA J ZA J Dimensions of the vacuum () port fittings after installation..7. KS0-MG KL0-MG... ZA J ZA J Dimensions of the air pressure supply () port fittings after installation 7 C
Series ZA supply () port Dimensions Release flow adjusting needle lug Type N ZA N 0 A 78. 8. ZA N supply () port M. 7. 9 Approx. 000 Supply adapter. Suction filter x ø.7 (Mounting hole) 9.9 ZA - -F Circuit diagram ZA N L F 0 Note) When the body is mounted, tighten with a torque of 0. ± 0.0 N m. Using excessive torque may cause damage to the body. ZA N M Dimensions of the vacuum () and air pressure supply () port fittings after installation Dimensions after the fittings are installed on the vacuum () port, and air pressure supply () port of a single unit are shown below. KS-MN 9. KS0-MN KL-MN. KL0-MN... ø7....8 ZA N ZA N 9. ZA N Dimensions of the vacuum () port fittings after installation ZA N..7. KS0-MG KL0-MG..7... C 8 ZA N ZA N Dimensions of the air pressure supply () port fittings after installation
0 A supply () port Compact acuum Ejector Series ZA Dimensions Release flow adjusting needle lug Type N ZA N 78. 8. ZA N ZA - F Circuit diagram supply () port M. 7. 9 Supply adapter. ZA N L F 0 Approx. 000 Suction filter x ø.7 (Mounting hole) 9.9 Note) When the body is mounted, tighten with a torque of 0. ± 0.0 N m. Using excessive torque may cause damage to the body. ZA N M Dimensions of the vacuum () and air pressure supply () port fittings after installation Dimensions after the fittings are installed on the vacuum () port, and air pressure supply () port of a single unit are shown below. KS-MN 9. KS0-MN KL-MN. KL0-MN... ø7....8 9. ZA N ZA N ZA N Dimensions of the vacuum () port fittings after installation ZA N..7. KS0-MG KL0-MG..7... ZA N ZA N Dimensions of the air pressure supply () port fittings after installation 9 C
Series ZA Dimensions Common air pressure supply () port L L L Manifold type (Common SU) ZZA ZA M Dimensions Manifold part no. ZZA- ZZA- ZZA- ZZA- ZZA- ZZA- ZZA7- ZZA8- Stations n 7 8 Common air pressure supply () port L 0 0 0 0 0 70 80 L 0 0 0 0 0 70 80 90 (mm) L 8 8 8 8 8 78 88 98 8. Manifold base 7. 9..8.. 7 Release flow adjusting needle x ø. (Mounting hole) (000) Suction filter M both sides common air pressure supply () port n x ZA -K -F -M ZA --M -J ZA - N ZA - N -F-M - -M Circuit diagram Note ) The above dimensions are for ZZA-00. ZA -K L-F -M. Note ) When the body is mounted, tighten with a torque of 0. ± 0.0 N m. Using excessive torque may cause damage to the body. Note ) When viewed from the manifold base, count the number of stations, to (n) beginning from the left side. Dimensions of the vacuum () and air pressure supply () port fittings after installation Dimensions after the fittings are installed on the vacuum () port, and the common air pressure supply () port of a manifold are shown below. KS-MN 9. KS0-MN KL-MN. KL0-MN... ø7....8 9. ZA M ZA M ZA M ZA M Dimensions of the vacuum () port fittings after installation KS0-MN. KS0-MN ø..7 ZX-M (lug)..8 KL0-MN 9.7.. KL0-MN C ZZA ZZA ZZA ZZA ZZA Dimensions after the fittings are installed on the common air pressure supply () port Note) The above drawings show the vacuum port from the front with the fitting attached on the right side. It is the same as when the fitting is attached on the left side.
Compact acuum Ejector Series ZA Manifold Type: How to Increase / Decrease Manifold Stations lanking plate assembly ZA- (O-ring and round head combination screws AC0090 (M x ) are attached.) Manifold base ZZA - An assembly kit (part no. ZA-O-) is available which includes pcs each of O-rings and round head combination screws.
Series ZA Specific roduct recautions e sure to read before handling. Refer to est neumatics No. for Safety Instructions and acuum Equipment recautions. Warning. Avoid energizing the solenoid valve for long periods of time. If a solenoid valve is energized for a long period of time, the coil will get hot and the performance may be reduced. Additionally, the peripheral equipment in close proximity may also be badly affected. Use a low wattage solenoid valve when the solenoid valve is energized continuously or when the duration of the energization is longer than the non-energized period each day. eriods of energization can be shortened by using a latching type solenoid valve. ut, do not energize the coil on both A and sides simultaneously when using the latching type. Continuous energization of the solenoid valve should be less than minutes in duration and the energization period should be shorter than the non-energized period. Take measures for any heat radiation so that the temperature is within the range of solenoid valve specifications when the solenoid valve is mounted on the control panel. lease pay special attention to any temperature increases when a manifold type with stations or more is energized continuously or when three individual units are placed in close proximity.. Use the vacuum equipment within the operating supply pressure range. When the operating with a lower supply pressure, the vacuum performance will be reduced and the poppet valve will cause malfunction. Never use the vacuum equipment more than the operating supply pressure range as this may cause damage to the product resulting in potentially dangerous operation.. Suspension of operation for long periods of time lease use caution as detailed below when the vacuum equipment is turned off for periods in excess of hours. e sure to turn off the pressure supply to the vacuum equipment. lease observe this precautions as the supply pressure will be applied for a extra period of time due to the line pressure increase and may result in damage to the vacuum equipment. e sure to turn off the power supply to the solenoid valve and the pressure switch. lease observe this precautions as any heat generated due to the length of energization time may seriously affect the vacuum equipment and peripheral equipment resulting in potentially dangerous operation.. Exhaust port (EXH port) on the vacuum ejector lease check the exhaust port (EXH port) on the vacuum ejector, so that any exhaust resistance will not be increased due to insulating materials or restrictions in the piping. The exhaust resistance may reduce the ejector s performance. Additionally, never use this product in an application where the exhaust port is blocked when detaching a workpiece. This misuse may result in possible damage to the product.. acuum release flow adjusting needle Adjust the vacuum release flow adjusting needle from the fully closed to the open state by /8 to / turns to detach a workpiece completely during the ON time of a release valve. Do not supply compressed air while the vacuum release flow adjusting needle is adjusted. Securely lock it with a lock nut after adjustment. Design and Selection Warning. How to use the latching type solenoid valve Our Latching type solenoid are fitted with a self-detaining mechanism. Its construction features an armature inside the solenoid which is set or reset using spontaneous energization. (0 ms or greater) Therefore, continuous energization is not required. How to Use the Latching Type lug Connector Wiring specifications Wiring should be connected as shown below. Connect with the power supply respectively. DC positive common SOL. DC negative common AC type SOL. SOL. Simultaneous energization protection circuit Simultaneous energization protection circuit A C A C A C Set (acuum generation) COM. Reset (acuum suspension) Set (acuum generation) COM. Reset (acuum suspension) Set (acuum generation) COM. Reset (acuum suspension) Lead wire colors ( ) lack (+) Red ( ) White Lead wire colors (+) Red ( ) lack (+) White Lead wire colors 0 AC, 00 AC Yellow Yellow lue Gray Gray Special care must be taken for the latching type.. Avoid using this product with a circuit which electrifies both the set and reset signals simultaneously.. The minimum energization time required for self-detaining is 0 ms.. lease contact us when using this product in locations where there are vibration levels of 0 m/s or above or highly magnetic fields. No problems arise in normal usage or locations.. This valve retains the reset position (Flow path: A R) at the time of shipment. However, it may alter to the set position during transporatation or due to vibration when mounting the valve. Therefore, confirm the home position either manually or with power supply prior to use. 7. Suction filter This suction filter is dedicated to the ZA series. Avoid using it for other purposes. Red
Series ZA Specific roduct recautions e sure to read before handling. Refer to est neumatics No. for Safety Instructions and acuum Equipment recautions. Warning Mounting. When the body is mounted, tighten with a torque of 0. ± 0.0 N m. Using excessive torque may cause damage to the body.. When the filter assembly is mounted, tighten with a torque of 0.07 ± 0.0 N m. Using excessive torque may cause damage to the filter case. Operating Environment Warning. Suction filter The filter case of this suction filter is made of nylon. The product will be damaged if solvents such as alcohol or chemicals are splashed on it. Avoid using it in an atmosphere where such solvents are present.