SAB 128R and SAB 163R Mk4 Screw compressor units. Spare parts manual

SAB 128R and SAB 163R Mk4 Screw compressor units Spare parts manual en

Spare Parts Manual SSaAB SAB128RandSAB163R Mk4 Spare Parts manual SAB 128R and SAB 163R Mk4 The screw compressor and unit can be fitted with different equipment, depending on their functions and requirements. Some of these equipment is described in this instruction manual even though they are not fitted on your particular unit. A cross (x) in the following table indicates which variants that are fitted on your unit -- with the compressor no stated below. Compressor SAB 128 SAB 163 Type of drive Refrigerant Compressor no Designation (Male drive) R717 Other Instrumentation UNISAB II and manual regulation of the V i slide UNISAB II and automatic regulation of the V i slide Oil cooling Economizer system (ECO--system) Water-cooled oil cooler Refrigerant--cooled oil cooler Refrigerant injection into discharge pipe Vessel type Closed system and vessel type Open system and vessel type OWRF/OWTF OOSI BLI HESS EOSE SVER Ex-execution Both compressor and unit are safeguarded. EN

EN

Contents 2010.10 Contents This Spare Parts Manual contains the following Standard Documents: 19. Spare Parts Drawings

Contents

Table of Contents List of parts for SAB 128R Mk 4... 18--1 Spare parts survey for SAB 128 R Mk4 unit... 18--6 Tools for compressor SAB 128 R Mk4... 18--11 List of parts for SAB 163R Mk 4... 18--15 Spare parts survey for SAB 163 R Mk4 unit... 18--21 Tools for compressor SAB 163 R Mk4... 18--26 0173--530--EN 18--0

List of parts for SAB 128R Mk 4 Pos. Designation Qty. Part no Compressor complete 4161--180 Compressor housing 10 Rotor housing, SAB 128 1 3011--052 Bearing cover at suction end 20 Suction cover for SAB 128 1 3013--391 21 O-ring 304.39 x 3.53 1 1331--112 22 Cylindrical pin ø16 x 40 2 1445--013 23 Cylinder screw M12 x 35 16 1413--387 24 Plug with collar 1/2 RG 1 1343--027 25 Dowty-ring 1 1331--430 26 O-ring 14.00 x 1.78 2 1331--190 Bearing cover at discharge end 40 Bearing cover 1 3013--477 43 Cylinder screw M10 x 35 6 1413--373 44 Adjusting screw 2 2111--122 45 Stop screw M6 x 10 4 1413--231 46 Plug with collar 1/8 RG 1 1343--024 47 Dowty-ring 1 1331--426 Cover for Vi-regulating cylinder 51 O-ring 82.14 x 3.53 1 1331--077 52 Cylinder screw M10 x 35 3 1413--373 55 Cover for Vi-slide 1 3013--286 Shaft seal cover 81 O-ring 85.32 x 3.53 1 1331--078 82 Cylinder screw M10 x 35 4 1413--373 83 Driving pin ø4 x 6 1 1446--011 86 Hose connecting branch 1/4 1 1345--143 87 Clear plastic hose 3/16 x 300 mm 1 1241--190 Cap cover 90 Cap cover 1 3013--421 91 O-ring 85.32 x 3.53 1 1331--078 92 Cylinder screw M10 x 35 4 1413--373 93 Dowty-ring dia. 15.88/11.84 x 2 1 1331--426 94 Plug with collar 1/8 RG 1 1343--024 95 Nozzle for bearing lubrication 1 3447--537 96 O-ring 14.00 x 1.78 1 1331--190 Cover for slide stop 100 Cover 1 3013--057 101 O-ring 66.27 x 3.53 1 1331--072 102 Cylinder screw M10 x 35 3 1413--373 103 Retainer for spindle bearings 1 3044--013 104 Cylinder screw M6 x 20 4 1413--341 105 Locking plate 1 2114--043 18--1 0173--530--EN

Pos. Designation Qty. Part no Rotor and suction end bearings 110 Rotor set for SAB 128, HR 1 3024--300 111 Roller bearings 2 1513--016 112 Retainer pin for male rotor 1 3021--012 113 Spirolox-ring 1 1437--217 114 Washer for bearings 2 3021--035 115 Cylinder screw M12 x 35 2 1413--387 118 Driving pin ø4 x 8 1 1446--019 119 Retainer for female rotor 1 3021--017 Discharge end bearings, female rotor 130 Balance piston dia. 64 1 3025--066 131 Radial roller bearings 40/90 x 33 1 1513--016 132 Four point bearings 40/90 x 23 1 1513--027 133 Shim dia. 70/90, for adjustment of distance between rotor and discharge ports. 1 2124--080 Comprising: 1 of thickness 0.49 mm 1 of thickness 0.52 mm 1 of thickness 0.55 mm 1 of thickness 0.58 mm 1 of thickness 0.61 mm 1 of thickness 0.64 mm 1 of thickness 0.67 mm Discharge end bearings, male rotor 135 Balance piston dia. 64 1 3025--066 136 Radial roller bearings 45/100 x 36 1 1513--012 137 Four point bearings 45/100 x 25 1 1513--028 138 Shim dia. 80/100, for adjustment of distance between rotor and discharge ports. 1 2124--081 Comprising: 1 of thickness 0.49 mm 1 of thickness 0.52 mm 1 of thickness 0.55 mm 1 of thickness 0.58 mm 1 of thickness 0.61 mm 1 of thickness 0.64 mm 1 of thickness 0.67 mm Discharge end ports 140-1 Discharge port (male rotor) Vi 4.5 1 3031--063 141-1 Discharge port (female rotor) Vi 4.5 1 3031--064 140-2 Discharge port (male rotor) AC-operation Vi 3.0 1 3031--068 141-2 Discharge port (female rotor) AC-operation Vi 3.0 1 3031--069 142 Cylinder screw M8 x 120 6 1413--314 143 Steel sealing ring ø13.5/8 x 4/2 6 3049--006 146 Plug with collar 3/8 RG 2 1343--026 147 Locking screw M10 x 10 2 1413--250 148 Adjusting screw M10 x 20 2 1413--032 149 Dowty-ring dia. 23.80/17.35 x 2.03 2 1331--427 0173--530--EN 18--2

Pos. Designation Qty. Part no Rotor adjustment parts 151 Inner cover (male rotor) 1 3013--422 152 O-ring 91.67 x 3.53 2 1331--080 153 Inner cover (female rotor) 1 3013--423 154 O-ring 82.14 x 3.53 2 1331--077 155 Nozzle for oil 2 3447--537 Shaft seal 160 Shaft seal type 680 1 1332--068 Inner shaft seal 165A Shaft seal cover 1 3013--420 165B Balance piston 1 3025--065 165C Slide ring with sleeve 1 3025--062 165D Radial seal 1 1332--077 165E Inner ring 1 3025--058 165F O-ring 39.34 x 2.62 2 1331--137 165G O-ring 59.99 x 2.62 2 1331--142 165I Counter sunk screw M4 x 10 4 1413--060 165J O-ring 14 x 1.78 1 1331--190 165K Oil distribution ring 1 3026--067 165L Spirolox-ring 1 1437--260 Suction filter 170 Suction filter 1 3042--081 Adjusting system for Vi -glider 180 Spindle for slide stop 1 3044--012 182 Sealing washer for slide stop 1 3044--014 183 Sealing ring 28/22 1 1331--503 184 O-ring 44.04 x 3.53 1 1331--065 186 Axial ball bearing 2 1512--015 Vi-regulating slide 193 Cylinder screw M10 x 12 1 1413--408 200 Capacity slide 1 3043--246 Parts for suction gas inlet 251 Hexagon head screw M12 x 30 8 1424--215 252 O-ring 132.94 x 3.53 1 1331--093 254 Cylinder screw M14 x 45 8 1413--413 18--3 Rev. 2012.07 0173--530--EN

Pos. Designation Qty. Part no Non-return valve 260 Non-return flap 1 3042--148 261 Intermediate flange 1 3013--424 262 O-ring dia. 183.74 x 3.53 1 1331--104 263 Hinge fastener 1 3042--150 264 Cylinder screw M8 x 80 2 1413--366 265 Hinge 1 3042--149 266 Shim 8 x 14 x 0.5 2 1436--149 267 Cylindrical pin dia. 8 x 32 1 1445--092 268 Sleeve for hinge 1 3042--152 269 Wave spring ø18.8 x ø13.2 x 0.2, h=1.6 1 1523--099 270 Counter sunk screw M8 x 25 1 1413--103 Economizer 290 ECO-plug 1 3013--426 291 Cylinder screw M10 x 30 2 1413--372 292 O-ring 29.74 x 3.53 1 1331--025 293 Cylinder screw M8x25 1 1413--357 HLI inlet 300 HLI plug 2 3013--136 301 Cylinder screw M10 x 30 4 1413--372 302 O-ring 20.22 x 3.53 2 1331--019 Parts for internal oil channel 320 Non-return valve EMB RVS 1 1364--277 321 Dowty-ring 1 1331--433 322 Plug with collar 3/4 RG 1 3013--491 323 Plug with collar 3/8 RG 1 1343--026 324 Dowty-ring 1 1331--427 325A Nozzle for rotor injection (R717) 1 3041--039 325B Nozzle for rotor injeciton (R22) 1 3041--040 326 Dowty-ring 6 1331--428 327 Plug with collar 1/4 RG 6 1343--025 328 Dowty-ring 2 1343--026 329 Plug with collar 3/8 RG 2 1331--427 Oil filter parts 450 Cover 1 3013--474 452 O-ring 132.94 x 3.53 1 1331--093 453 O-ring 101.19 x 3.53 1 1331--083 455 Locking nut M10 1 1433--080 456 Cylinder screw M12 x 35 4 1413--387 458 Stay bolt 1 2111--131 459 Magnet 4 1517--022 460 Intermediate ring 4 3424--039 461 Rubber gasket 2 1334--012 0173--530--EN 18--4

Pos. Designation Qty. Part no 470 Filter cartridge 1 1517--150 471 Gas outlet device 1 3042--158 472 O-ring 101.19 x 3.53 1 1331--083 473 Cover 1 3013--374 474 Cylinder screw M12 x 35 1 1413--387 475 O-ring 132.94 x 3.53 1 1331--093 476 Float switch 1 1553--262 477 Cylindrical pin 3 x 12 1 1445--054 478 Plug with collar 1/4 1 1343--025 479 Dowty-ring 1 1331--428 480 Plug with collar 3/4 1 1343--028 481 Dowty-ring 2 1331--433 Safety valve system 700--1 700--2 700--3 700--4 700--5 Back pressure independent safety valve BSV8, 18 bar Back pressure independent safety valve BSV8, 20 bar Back pressure independent safety valve BSV8, 21 bar Back pressure independent safety valve BSV8, 22 bar Back pressure independent safety valve BSV8, 25 bar - Other valve types are available on request 1 1 4 1 1 2416--202 2416--203 2416--204 2416--224 2416--205 701 Connecting pipe, POV 40, ø12 1 2332--711 702 Cylinder screw M12 x 35 4 1413--387 703 O-ring 85.32 x 3.53 1 1331--078 704 Intermediate pipe with POV 40 1 3014--027 716 Cylinder screw M14 x 35 4 1413--412 717 O-ring 72.62 x 3.53 1 1331--074 718 Safety valve cover 1 3013--425 719 O-ring 183.75 x 3.53 1 1331--104 720 Male stud coupling 2 1349--053 726 Reducer 3/4 -- 3/8 RG 1 2312--038 727 Al. Ring 24/13 x 1.5 1 2356--127 730 Union nut G1 1 2313--017 731 Nipple G3/8, NV17 1 2311--065 732 Al. Ring 30/16 x 1.5 1 2356--137 733 Dowty-ring 1 1331--427 734 Cylinder screw M14 x 40 8 1413--410 Temperature/pressure transducers 751 Pressure transmitter at suction end 1 1373--249 752 Pressure transmitter after oil filter 1 1373--271 753 Pressure transmitter before oil filter 1 1373--271 755 Male stud coupling EMB VADKO 2 1349--137 756 Screw connection EMB VBDKO 1 1349--233 761 Temperature transmitter 1 1373-343 762 Temperature transmitter 1 1373--345 765 Dowty-ring 1 1331--428 18--5 0173--530--EN

Spare parts survey for SAB 128 R Mk4 unit The following list comprises all components that can be fitted on a compressor unit. From this list we have selected the components that are used on a particular unit and which are indicated on the piping diagram of this instruction manual. The position numbers on the piping diagram are a reference to the Pos. columns of this list. The piping diagram is dedicated to the compressor number stated on page 1 of this instruction manual. The components in the shaded areas are variable. This may be due to voltage, refrigerant, approved pressure etc. On ordering spare parts it may be an advantage to receive them in sets selected for your specific compressor unit. A list of sets can had on request from SABROE s local representative. Pos. Designation Part no. Regulating & Control device PT1 PT2 PT3 PT4 TT5 TT6/7 GT8 GT9 UNISAB II Pressure transducer Pressure transducer See PT2 See PT2 Temperature transducer Temperature transducer Position transmitter (capacity) See GT8 --1 -- 9 bar --1 -- 25 bar PT100 1373-249 1373-271 1373-264 3448-004 UNISAB II Frontpanel 1573-007 1 CPU-module 1572-026 1 Relay print 1574-016 1 EPROM extractor 1613-002 1 EEPROM extractor 1613-003 1 EEPROM 1571-018 3 Jumpers 2 Fuses 1 Screw driver g 1373-282 1572-018 0173--530--EN 18--6

Pos. Suction: Designation Part no. 20 O-ring dia 132,94 x 3,53 1331-093 Set of gaskets for SVA--ST 80 1377--421 Set of gaskets for SVA--ST 100 1377--422 Set of gaskets for SVA--ST 125 1377--423 24, 48, 64 34, 35,47 Set of gaskets for SNV 8 Set of gaskets for SNV 8 or 2453-053 Set of gaskets for QDV 15 2453-092 Oil separator, general: 30 Sealing ring dia. 42/49 x 6,5 1349-213 Refrigerant system 30 31 Heating rod, 250 V Heating rod, 115 V Heating rod, 230 O-ring dia 52,07 x 2,62 Sight glass (sight glass) 3181-038 3181-039 3181-040 1331-140 1226-017 55 O-ring dia 329,57 x 5,33 55 Oil seperating element (for cover) 1331-184 1517-062 50--54 Oil return: Oil return valve complete Repair kit 3447--526 1377--246 204 28 29 Discharge: Set of gaskets for SVA--ST 65 O-ring dia 78,97 x 3,53 Safety valves: SFV 15 O--ring 15,54 x 2,62 Spring 20 bar Opening pressure Spring 25 bar Opening pressure DSV 32 gasket kit 1377--420 1331-076 1331--015 2161--004 2161--005 2453--065 18--7 0173--530--EN

Pos. Designation Part no. Oil system 60 61 64 65 46 Flange connection, oil tube Gasket, dia 57/43 x 2 2356-260 O-ring dia 59,92 x 3,53 (compr.) Oil pump 1331-071 1524--227 Set of gaskets for SVA 25 148B--4016 Filter element FIA D25 1375--083 Set of gasket, SNV 8 2453--053 Set of gaskets for SVA 15 1377--417 Thermostatic three-way valve, type RT5 O-ring, Neoprene 1331-383 Thermo element, 48 C 1365-005 Capacity regulation Only HF/HM 70 71 72 Solenoid valve block Valve housing EVM (NC) Gasket set for EVM (NC/NO) Coil 10 W 220 V 50/60 Hz 110 V 50/60 Hz 240 V 50/60 Hz Solenoid valve: Valve housing EVM (NO) Coil 10 W 220 V 50/60 Hz 110 V 50/60 Hz 240 V 50 Hz Throttle valve 1372-335 1336-024 1372-537 1372-538 1372-539 1372-337 1372-537 1372-538 1372-539 O--ring 10,82 x 1,78 O--ring4,47x1,78 Gasket 19/14 1331--008 1331--005 2356--283 0173--530--EN 18--8

Pos. 80-84 81 Gasket set for SVA--ST 15--20 Filter FA15: (When TEAT 20 is selected) Gasket set for FA15 Repair kit for FA15 Designation Part no. 1377--417 1377-078 1377-250 81 Filter FA20: (When TEAT 85 is selected) HLI Oil cooling Gasket set for FA20 Repair kit for FA20 82 Solenoid valve EVRA15 (when TEAT 20 is selected) Gasket set (for EVRA 15) Repair kit (for EVRA 15) Coil 10 W 220 V 50/60 Hz g 110 V 50/60 Hz 240 V 50 Hz See pos 70 1377-079 1377-251 1377-093 1377-099 82 Solenoid valve EVRA20 (when TEAT 85 is selected) Gasket set (for EVRA 20) Repair kit (for EVRA 20) Coil 10 W 220 V 50/60 Hz g 110 V 50/60 Hz 240 V 50 Hz See pos 70 1377-094 1377-069 18--9 0173--530--EN

Pos. Designation Part no. HLI Oil cooling 83 83 Injection valve TEAT 20 Nozzle insert 20-5 1371-202 Nozzle insert 20-8 1371-203 Nozzle inset 20-12 Nozzle insert 20-20 Thermal part 35-65 deg. C 1371-204 1371-206 1371-255 Thermal part 55-95 deg. C 1371-253 Injection valve TEAT 85 Nozzle insert 85-33 1371-207 Nozzle insert 85-55 1371-208 Nozzle insert 85-85 1371-209 Thermal part : 20/85 068G3260 85--33 068G6070 85--55 1371--247 85--85 1371--248 83 Injection valve PMFL 80 Gasket set Piston rod Spare parts set for coupling S952 size 225 1377-040 1377-086 Compr. connections Sheets, bolts, nuts & slices 1524-124 Spacer bushing 1526-002 Stop screw M10 x 10 1413-250 Combination wrench 9/16 Compr. Box wrench 9/16 Tools Alignment motor - compressor Discs (motor up to IEC 280) 2221-067 Discs ( motor from IEC 315) 2221-076 Tools 3183-104 0173--530--EN 18--10

Tools for compressor SAB 128 R Mk4 1 2 3 4 5 6 7 8.-- 9 10 11 23.-- 24 25 21 22.-- 15 20.-- 30 31 32.-- 33 34 43 44.-- 45.-- 46 42 40.-- 50.-- 51.-- 52 53 54.-- 55 56 57 T0177095 18--11 0173--530--EN

Line no A401 = Normal set (part no. 3083-044) Line no. A402 = Extended set (part no 3083-046) Line no. B401 = Tools for coupling alignment (part no 3183-104) Line no. B402 = Tools for shaft seal removal, oil pump (part no 3083-160) Tool no. Designation Part no. A401 A402 B401 B402 1 Puller for bearings 3083-060 1 1 2 Thrust ring for the puller, female 3083-043 1 1 3 Thrust ring for the puller, male 3083-127 1 1 4 Tool for fitting the bearings 3083-062 1 1 5 Ring for the puller 3083-042 1 1 6 Tool for pressing out the rotors 3083-063 1 1 7 Tool for fitting the bearings 3083-061 1 1 8.1 Retaining cup for male rotor 3083-097 1 1 8.2 Retaining cup for female rotor 3083-098 1 1 9 Tool for dismounting the bearings 3083-041 2 2 10 Thrust washer 3083-002 1 1 11 Locking tool for rotor 3083-126 1 1 15 Punch f. locking the rotor 3083-358 1 1 20.1 Threaded pin M10 x 160 2112-129 4 4 20.2 Threaded pin M12 x 275 2112-148 1 1 21.1 Hexagon head screw M16 x 130 1424-271 1 1 21.2 Hexagon head screw M10 x 130 1424-203 4 4 22.2 Socket cap screw M8 x 35 1413-359 1 1 22.3 Socket cap screw M8 x 120 1413-314 2 2 22.4 Socket cap screw M10 x 25 1413-371 4 4 22.6 Socket cap screw M12 x 35 1413-387 1 1 22.7 Socket cap screw M12 x 90 1413-400 1 1 23.1 Nuts M8 1432-063 2 2 23.2 Nuts M10 1432-064 4 4 23.3 Nuts M12 1432-065 1 1 24.1 Washer dia. 24/13 x 2.5 1436-036 1 1 24.2 Washer dia. 35/13 x 5 1436-140 3 3 25 Guide pin M16 x 300 2112-147 2 2 0173--530--EN 18--12

Tool no. Designation Part no. A401 A402 B401 B402 30 Tool for adjusting the bearings 3083-096 1 1 31 Special screw for adjusting the bearings 3083-095 1 1 32.1 Eye bolt M12 1427-150 1 1 32.2 Eye bolt M16 1427-156 1 1 33 Alignment device for coupling 3183-104 1 34 Feeler gauge 1622-050 1 36 Tools for shaft seal removal, oil pump Consist of: 36,1 Puller for shaft seal, oil pump 3083-157 1 36,2 Cap screw M10 x 75 1424-201 1 36,3 Threaded pin M8 x 150 3083-156 3 36,4 Nut M8 1432-063 3 36,5 Punch dia. 18 x 80 3083-158 1 36,6 Punch dia. 22/16,5 x 100 3083-159 1 40.1 Torque wrench (Ratchet) 5-50 Nm 1/2 1 40.2 Torque wrench 40-200 Nm (14 x 18) 1 42 Extension 1/2 1 43 Converter for torque wench(14x18) - 1/2 1 44.1 Hexagon bit adapter 1/2-4mm 1 44.2 Hexagon bit adapter 1/2-5mm 1 44.3 Hexagon bit adapter 1/2-6mm 1 44.4 Hexagon bit adapter 1/2-8mm 1 44.5 Hexagon bit adapter 1/2-10mm 1 44.6 Hexagon bit adapter 1/2-14mm 1 45 Box spanner insert 1/2-19mm 1 45.1 Box spanner insert 1/2-24mm 1 45.2 Box spanner insert 1/2-27mm 1 45.3 Box spanner insert 1/2-36mm 1 45.4 Box spanner insert 1/2-1/2 1 46 Open end spanner (14x18) - 19mm 1 18--13 0173--530--EN

Tool no. Designation Part no. A401 A402 B401 B402 50.1 Combination spanner 17mm 1612-276 1 50.2 Combination spanner 19mm 1612-277 1 50.3 Combination spanner 1/2 51.1 Allen key for socket cap screw 3mm 1612-395 1 51.2 Allen key for socket cap screw 5mm 1612-397 1 51.3 Allen key for socket cap screw 6mm 1612-398 1 51.4 Allen key for socket cap screw 8mm 1612-399 1 51.5 Allen key for socket cap screw 10mm 1612-401 1 51.6 Allen key for socket cap screw 14mm 1612-400 1 52 Magnetic Fixture for dial indicator 1 53 Dial indicator 1 54.1 Retaining ring pliers 1 54.2 Retaining ring pliers 1 55.1 Hammer 1612-012 1 55.2 Plastic hammer 1612-042 1 56 Steel punch 8 mm 1 57 Pliers for driving pin 1612-190 1 0173--530--EN 18--14

List of parts for SAB 163R Mk 4 Hovedstykliste : 4169--020 Pos. Designation Qty. Part no Compressor complete, male, Man. Vi 1 4161--170 Compressor housing 10 Rotor housing, SAB 163 H 1 3011--051 Bearing cover at suction end 20 Suction cover for SAB 163 H 1 3013--372 21 O-ring 380.37 x 5.33 1 1331--187 22 Cylindrical pin dia. 16 x 50 2 1445--091 23 Cylindrical screw M16 x 45 16 1413--433 24 Plug with collar 1/2 1 1343--027 25 AL gasket dia. 27/21 x 1,5 1 2356--133 26 O-ring 14.00 x 1.78 2 1331--190 Bearing cover at discharge end 40 Bearing cover 1 3013--475 43 Cylinder screw M10 x 35 6 1413--373 44 Adjusting screw M20 2 2111--122 45 Stop screw M6 x 10 2 1413--231 46 Plug with collar 1/4 1 1343--025 47 Dowty-ring 20.75/13.74 x 2.03 1 1331--428 Cover for Vi-slide 51 O-ring 107.54 x 3.53 1 1331--085 52 Cylinder screw M12 x 40 3 1413--388 55 Cover for slide housing 1 3013--287 Shaft seal cover 81 O-ring 113.89 x 3.53 1 1331--087 82 Cylinder screw M12 x 35 4 1413--387 83 Driving pin dia. 4 x 6 1 1446--011 86 Hose connecting branch 1/4 1 1345--143 87 Clear plastic hose 3/16 x300 mm 1 1241--190 Cap cover 90 Cap cover 1 3013--371 91 O-ring 113.89 x 3.53 1 1331--087 92 Cylinder screw M12 x 35 4 1413--387 93 Dowty-ring dia. 15.88/11.84 x 2.0 1 1331--426 94 Plug with collar 1/8 1 1343--024 95 Nozzle for bearing lubrication 3 3447--537 96 O-ring 14.00 x 1.78 1 1331--190 18--15 0173--530--EN

Pos. Designation Qty. Part no Cover for slide stop 100 Cover forslide stop 1 3013--068 101 O-ring 78.97 x 3.53 1 1331--076 102 Cylinder screw M12x35 4 1413--387 103 Bearing housing 1 3021--018 104 Cylinder screw M6x20 4 1413--341 105 Locking plate 1 2114--043 Rotor and suction end bearings 110 Set of rotors for SAB 163HR 1 3024--343 111 Radial roller bearings 2 1513--017 113 Spirolox-ring 1 1437--287 114 Washer for bearings 2 3021--007 115 Cylinder screw M16 x 45 2 1413--341 118 Driving pin dia. 4.0 x 10 1 1446--012 119 Retainer pin 2 3021--009 Discharge end bearings, female rotor 130 Balance piston dia. 81 1 3025--064 131 Radial roller bearings dia. 55/120 x 43 1 1513--074 132 Four-point bearings dia. 55/120 x 29 1 1513--076 133 Set of shims dia. 100/120, for adjustment of distance between rotors and discharge ports Comprising: 1 of thickness 0.49 mm 1 of thickness 0.52 mm 1 of thickness 0.55 mm 1 of thickness 0.58 mm 1 of thickness 0.61 mm 1 of thickness 0.64 mm 1 of thickness 0.67 mm 1 2124--082 Discharge end bearings, male rotor 135 Balance piston dia. 81 1 3025--075 136 Radial roller bearings dia. 60/130 x 46 1 1513--075 137 Four-point bearings dia. 60/130 x 31 1 1513--077 138 Set of shims, dia. 105/130, for adjustment of distance between rotor and discharge ports Comprising: 1 of thickness 0.49 mm 1 of thickness 0.52 mm 1 of thickness 0.55 mm 1 of thickness 0.58 mm 1 of thickness 0.61 mm 1 of thickness 0.64 mm 1 of thickness 0.67 mm 1 2124--083 0173--530--EN 18--16

Pos. Designation Qty. Part no Discharge end ports 140 Discharge port (male rotor) 1 3031--059 140-1 Discharge port AC (male rotor) 1 3031--066 141 Discharge port (female rotor) 1 3031--060 141-1 Discharge port AC (female rotor) 1 3031--067 142 Cylinder screw M10 x 150 6 1413--376 143 Steel sealing ring dia. 16/10 x 2 6 2351--030 146 Plug with collar 3/8 2 1343--026 147 Locking screw M10 x 10 2 1413--250 148 Adjusting screw M10 x 16 2 1413--032 149 Dowty-ring dia. 23.80/17.35 x 2.03 2 1331--427 Rotor adjustment parts 151 Inner cover (male rotor) 1 3013--382 152 O-ring dia. 123.42 x 3.53 2 1331--090 153 Inner cover (female rotor) 1 3013--383 154 O-ring dia. 113.89 x 3.53 2 1331--087 Shaft seal 160 Shaft seal type 680 1 1332--162 Inner shaft seal 165A Shaft seal cover 1 3013--380 165B Balance piston 1 3025--063 165C Slide ring with sleeve 1 3025--061 165D Radiel seal 1 1332--079 165E Inner ring 1 3025--055 165F O-ring 50.52 x 1.78 1 1331--244 165G O-ring 69.52 x 2.62 1 1331--145 165I Counter sunk screw M6 x 12 4 1413--090 165J O-ring 14.00 x 1.78 1 1331--190 165K Oil distribution ring 1 3026--061 165L Spirolox-ring 1 1437--260 Suction filter 170 Suction filter 1 1517--151 Adjusting system for Vi slide 180 Spindle for slide stop 1 3044--149 182 Sealing washer for slide stop 1 3044--014 183 Sealing ring 1 1331--503 184 O-ring 44.04 x 3.53 1 1331--065 186 Axial ball bearing ø42/25 x 11 2 1512--015 Vi regulating slide 193 Cylinder screw M10 x 20 1 1413--370 200 Capacity slide 1 3043--274 18--17 0173--530--EN

Pos. Designation Qty. Part no Parts for suction gas inlet 251 Hexagon head screw M16 x 65 8 1422--634 252 O-ring dia. 190.09 x 3.53 1 1331--105 Non-return valve 260 Non-return flap 1 3042--146 261 Intermediate flange 1 3013--376 262 O-ring dia. 215.49 x 3.53 1 1331--108 263 Hinge fastener 1 3042--150 264 Cylinder screw M8 x 80 2 1413--366 265 Hinge 1 3042--145 266 Shim 8 x 14 x 0.5 2 1436--149 267 Cylindrical pin dia. 8 x 32 1 1445--092 268 Sleeve for hinge 1 3042--152 269 Wave spring ø18.8 x ø13.2 x 0.2, h=1.6 1 1523--099 270 Counter sunk screw M8 x 25 1 1413--103 271 Cylinder screw M8 x 25 2 1413--357 Economizer 290 ECO-plug 1 3013--377 291 Cylinder screw M10 x 30 1 1413--372 292 O-ring 37.69 x 3.53 1 1331--030 293 Cylinder screw M8 x 25 1 1413--357 HLI inlet 300 HLI plug 2 3013--127 301 Cylinder screw M10 x 30 4 1413--372 302 O-ring 23.39 x 3.53 2 1331--022 Parts for internal oil channel 320 Non-return valvel EMB RVS 1 1364--272 321 Dowty-ring 1 1331--437 322 Plug with collar 1 RG 1 1343--030 323 Plug with collar 3/8 1 1343--026 324 Dowty-ring 1 1331--427 325A Nozzle for rotor injection (R717) 1 3041--031 325B Nozzle for rotor injection (R22) 1 3041--035 326 Dowty-ring 6 1331--428 327 Plug with collar 1/4 6 1343--025 328 Dowty-ring 2 1331--430 329 Plug with collar 1/2 2 1343--027 0173--530--EN 18--18

Pos. Designation Qty. Part no Oil filter parts 450 Cover 1 3013--474 452 O-ring dia. 132.94 x 3.53 1 1331--093 453 O-ring dia. 101.19 x 3.53 1 1331--083 455 Locking nut M10 1 1433--080 456 Cylinder screw M12 x 35 1 1413--387 458 Stay bolt 1 2111--130 459 Magnet 4 1517--022 460 Intermediate ring 4 3424--039 461 Rubber gasket 1 1334--012 470 Filter cartridge 1 1517--121 471 Gas outlet device 1 3042--153 472 O-ring dia. 101.19 x 3.53 1 1331--083 473 Cover 1 3013--374 474 Cylinder screw M12 x 35 4 1413--387 475 O-ring 132.94 x 3.53 1 1331--093 476 Float switch 1 1553--262 477 Cylindrical pin ø3 x 12 1 1445--054 478 Plug with collar 1/4 1 1343--025 479 Dowty-ring 1 1331--428 480 Plug with collar 3/4 1 1343--028 481 Dowty-ring 2 1331--433 Safety valve system 700-1 Back pressure independent safety valve BSV8, 18 bar 1 2416-202 700-2 Back pressure independent safety valve BSV8, 20 bar 1 2416-203 700-3 Back pressure independent safety valve BSV8, 21 bar 1 2416-204 700-4 Back pressure independent safety valve BSV8, 22 bar 1 2416-224 700-5 Back pressure independent safety valve BSV8, 25 bar 1 2416-205 - Other valve types are available on request 701 Connecting pipe BSV8/POV 40/50 1 2332--685 702 Cylinder screw M12 x 35 4 1413--387 703 O-ring dia. 82,14 x 3,53 1 1331--077 704--1 Intermediate pipe with POV 40 1 3014--019 704--2 Intermediate pipe with POV 50 1 3014--021 716 Cylinder screw M16 x 40 4 1413--432 717 O-ring dia. 113,89 x 3,53 1 1331--087 718 Safety valve cover 1 3013--375 719 O-ring dia. 215.49 x 3.53 1 1331--108 720 Male stud coupling 2 1349--053 726 Reducer G3/4 --G3/8 1 2312--038 727 AL Ring 24/13x1,5 1 2356--127 18--19 0173--530--EN

Pos. Designation Qty. Part no 730 Union nut G1 1 2313--017 731 Nipple G3/8 x ø30, NV17 1 2311--065 732 AL Ring 30/16x1,5 1 2356--137 733 Dowty-ring 1 1331--427 734 Cylinder screw M16 x 40 8 1413--432 Temperature/pressure transducers 751 Pressure transmitter at suction end 1 1373--249 752 Pressure transmitter after oil filter 1 1373--271 753 Pressure transmitter before oil filter 1 1373--271 755 Male stud coupling EMB VADKO 2 1349--137 756 Screw connection EMB VBDKO 1 1349--233 761 Temperature transmitter 1 1373-343 762 Temperature transmitter 1 1373-345 765 Dowty-ring 2 1331--428 0173--530--EN 18--20

Spare parts survey for SAB 163 R Mk4 unit The following list comprises all components that can be fitted on a compressor unit. From this list we have selected the components that are used on a particular unit and which are indicated on the piping diagram of this instruction manual. The position numbers on the piping diagram are a reference to the Pos. columns of this list. The piping diagram is dedicated to the compressor number stated on page 1 of this instruction manual. The components in the shaded areas are variable. This may be due to voltage, refrigerant, approved pressure etc. On ordering spare parts it may be an advantage to receive them in sets selected for your specific compressor unit. A list of sets can had on request from SA- BROE s local representative. Pos. Designation Part no. Regulating & Control device PT1 PT2 PT3 PT4 TT5 TT6/7 GT8 GT9 UNISAB II Pressure transducer Pressure transducer See PT2 See PT2 Temperature transducer Temperature transducer Position transmitter (capacity) See GT8 --1 -- 9 bar --1 -- 25 bar PT100 1373-249 1373-271 1373-264 3448-004 UNISAB II Frontpanel 1573-007 1 CPU-module 1572-026 1 Relay print 1574-016 1 EPROM extractor 1613-002 1 EEPROM extractor 1613-003 1 EEPROM 1571-018 3 Jumpers 2 Fuses 1 Screw driver g 1373-282 1572-018 18--21 0173--530--EN

Pos. Suction: Designation Part no. 20 O-ring dia 190,09 x 3,53 1331-105 Set of gaskets for SVA--ST 100 1377--422 Set of gaskets for SVA--ST 125 1377--423 Set of gaskets for SVA--ST 150 1377--424 24, 48, 64 34, 35,47 Set of gaskets for SNV 8 Set of gaskets for SNV 8 or Set of gaskets for QDV 15 2453-053 2453-092 Oil separator, general: Refrigerant system 30 30 31 Sealing ring dia. 42/49 x 6,5 Heating rod, 250 V Heating rod, 115 V Heating rod, 230 O-ring dia 52,07 x 2,62 Sight glass (sight glass) 1349-213 3181-038 3181-039 3181-040 1331-140 1226-017 55 O-ring dia 329,57 x 5,33 55 Oil seperating element (for cover) 1331-184 1517-061 50--54 204 28 29 Oil return: Oil return valve complete Repair kit Discharge: Set of gaskets for SVA--ST 100 O-ring dia 120,4 x 3,53 Safety valves: SFV 15 O--ring 15,54 x 2,62 Spring 20 bar Opening pressure Spring 25 bar Opening pressure DSV 32 gasket kit 3447--526 1377--246 1377--422 1331-089 1331--015 2461--004 2461--005 2453--065 0173--530--EN 18--22

Pos. Designation Part no. Oil system 60 61 64 65 46 Flange connection, oil tube Gasket, dia 75/61 x 2,0 2356-220 O-ring dia 59,92 x 3,53 (compr.) Oil pump 1331-071 1524--227 Set of gaskets for SVA 25 148B--4016 Filter element FIA 25 1375--083 Set of gasket, SNV 8 2453--053 Set of gaskets for SVA 15 1377--417 Thermostatic three-way valve, type RT5 O-ring, Neoprene 1331-383 Thermo element, 48 C 1365-005 Capacity regulation Only HF/HM 70 71 72 Solenoid valve block Valve housing EVM (NC) Gasket set for EVM (NC/NO) Coil 10 W 220 V 50/60 Hz 110 V 50/60 Hz 240 V 50 Hz Solenoid valve: Valve housing EVM (NO) Coil 10 W 220 V 50/60 Hz 110 V 50/60 Hz 240 V 50 Hz Throttle valve 1372-335 1336-024 1372-537 1372-538 1372-539 1372-337 1372-537 1372-538 1372-539 O--ring 10,82 x 1,78 O--ring4,47x1,78 Gasket 19/14 1331--008 1331--005 2356--283 18--23 0173--530--EN

Pos. 80-84 81 Gasket set for SVA--ST 15--20 Filter FA15: (When TEAT 20 is selected) Gasket set for FA15 Repair kit for FA15 Designation Part no. 1377--417 1377-078 1377-250 HLI Oil cooling 81 Filter FA20: (When TEAT 85 is selected) Gasket set for FA20 Repair kit for FA20 82 Solenoid valve EVRA15 (when TEAT 20 is selected) Gasket set (for EVRA 15) Repair kit (for EVRA 15) Coil 10 W 220 V 50/60 Hz g 110 V 50/60 Hz See pos 70 240 V 50 Hz 1377-079 1377-251 1377-093 1377-099 82 Solenoid valve EVRA20 (when TEAT 85 is selected) Gasket set (for EVRA 20) Repair kit (for EVRA 20) Coil 10 W 220 V 50/60 Hz g 110 V 50/60 Hz 240 V 50 Hz See pos 70 1377-094 1377-069 0173--530--EN 18--24

Pos. Designation Part no. HLI Oil cooling 83 83 Injection valve TEAT 20 Nozzle insert 20-8 1371-203 Nozzle inset 20-12 1371-204 Nozzle insert 20-20 1371-206 Thermal part 35-65 deg. C 1371-255 Thermal part 55-95 deg. C 1371-253 Injection valve TEAT 85 Nozzle insert 85-33 Nozzle insert 85-55 Nozzle insert 85-85 1371-207 1371-208 1371-209 Thermal part : 20/85 068G3260 85--33 068G6070 85--55 1371--247 85--85 1371--248 83 Injection valve PMFL 80 Gasket set Piston rod Spare parts set for coupling S952 size 262 1377-040 1377-086 Compr. connections Sheets, bolts, nuts & slices 1524-125 Spacer bushing 1526-003 Stop screw M10 x 10 1413-250 Combination wrench 9/16 Compr. Box wrench 9/16 Tools Alignment motor - compressor Discs (motor up to IEC 280) 2221-067 Discs ( motor from IEC 315) 2221-076 Tools 3183-104 18--25 0173--530--EN

Tools for compressor SAB 163 R Mk4 1 2 3 4 5 6 7 8.-- 9 10 11 23.-- 24 25 21 22.-- 15 20.-- 30 31 32.-- 33 34 43 44.-- 45.-- 46 42 40.-- 50.-- 51.-- 52 53 54.-- 55 56 57 T0177095 0173--530--EN 18--26

Line no. A401 = Normal set (part no. 3083-047) Line no. A402 = Extendet set (part no. 3083-049 incl. 3083-048) Line no. B401 = Tools for alining the coupling (part no. 3183-104) Line no. B402 = Tools for shaft seal removal, oil pump (part no 3083-160) Tools no. Designation Part no. A401 A402 B401 B402 1 Puller for bearings 3083-131 1 1 2 Thrust ring for the puller, female 3083-130 1 1 3 Thrust ring for the puller, male 3083-054 1 1 4 Tools for fitting the bearings 3083-058 1 1 5 Ring for the puller 3083-053 1 1 6 Tools for pressing out the rotors 3083-132 1 1 7 Tools for fitting the bearings 3083-133 1 1 8.1 Retaining cup for male rotor 3083-102 1 1 8.2 Retaining cup for female rotor 3083-103 1 1 9 Tools for dismounting the bearings 3083-052 2 2 10 Thrust washer 3083-129 1 1 11 Locking tool for rotor 3083-365 1 1 12 Bearing dia 42/25 x 11 1512-015 1 1 15 Punch f. locking the rotor 3083-357 20.1 Threaded pins M10 x 160 2112-129 4 4 20.2 Threaded pin M16 x 325 2112-151 1 1 21.1 Hexagon head screw M20 x 120 1424-298 1 1 21.2 Hexagon head screw M10 x 130 1424-203 4 4 22.2 Socket cap screw M8 x 35 1413-359 1 1 22.3 Socket cap screw M8 x 120 1413-314 2 2 22.4 Socket cap screw M10 x 25 1413-371 4 4 22.6 Socket cap screw M16 x 50 1413-434 1 1 22.7 Hexagon head screw M16 x 130 1424-113 1 1 23.1 Nuts M8 1432-063 2 2 23.2 Nuts M10 1432-064 4 4 23.3 Nuts M16 1432-067 1 1 24.2 Washer dia. 45/17 x 5 3083-114 4 4 25 Guide pin M16 x 300 2112-147 2 2 30 Tools for adjusting the bearings 3083-101 1 1 18--27 0173--530--EN

Tools no. Designation Part no. A401 A402 B401 B402 31 Special screw for adjusting the bearings 3083-100 1 1 32.2 Eye bolt M16 1427-156 1 1 33 Alignment device for coupling 3183-104 1 34 Feeler gauge 1622-050 1 36 Tools for shaft seal removal, oil pump Consists of: 36,1 Puller for shaft seal, oil pump 3083-157 1 36,2 Cap screw M10 x 75 1424-201 1 36,3 Threaded pin M8 x 150 3083-156 3 36,4 Nuts M8 1432-063 3 36,5 Punch dia. 18 x 80 3083-158 1 36,6 Punch dia. 22/16,5 x 100 3083-159 1 40.1 Torque wrench (Ratchet) 5-50 Nm 1/2 1 40.2 Torque wrench 40-200 Nm (14 x 18) 1 42 Extention 1/2 1 43 Converter for torque wench(14x18) - 1/2 1 44.2 Hexagon bit adaptor 1/2-5mm 1 44.3 Hexagon bit adaptor 1/2-6mm 1 44.4 Hexagon bit adaptor 1/2-8mm 1 44.5 Hexagon bit adaptor 1/2-10mm 1 44.6 Hexagon bit adaptor 1/2-14mm 1 45 Box spanner insert 1/2-19mm 1 45.2 Box spanner insert 1/2-30mm 1 45.3 Box spanner insert 1/2-36mm 1 45.4 Box spanner insert 1/2-9/16 1 46 Open end spanner (14x18) - 24mm 1 50.1 Combination spanner 17mm 1612-276 1 50.2 Combination spanner 9/16 1 0173--530--EN 18--28

Tools no. Designation Part no. A401 A402 B401 B402 51.1 Allen key for socket cap screw 3mm 1612-395 1 51.2 Allen key for socket cap screw 5mm 1612-397 1 51.3 Allen key for socket cap screw 6mm 1612-398 1 51.4 Allen key for socket cap screw 8mm 1612-399 1 51.5 Allen key for socket cap screw 10mm 1612-401 1 51.6 Allen key for socket cap screw 14mm 1612-400 1 52 Magnetic Fixture for dial indicator 1 53 Dial indicator 1 54.1 Retaining ring plier 1 54.2 Retaining ring plier 1 55.1 Hammer 1612-012 1 55.2 Plastics hammer 1612-042 1 56 Steel punch 10 mm 1 57 Plier for driving pin 1612-190 1 18--29 0173--530--EN

19. Spare Parts Drawings 19. Spare Parts Drawings Table of Contents Drawings for SAB 128R Mk 4... 19--1 Drawings for SAB 163R Mk 4... 19--10 0173--530--EN 19--0

19. Spare Parts Drawings 04.03 93 92 94 92 93 90 94 95 96 91 165A 86 91 83 165D 87 160 165I 165K 165J 165L 104 102 105 100 23 182 184 186 326 183 180 186 103 101 327 326 25 24 26 21 264 263 266 267 262 762 755 756 751 252 250A 251 269 265 260 270 261 254 765 4161--T15 165C 165G 327 268 26 193 165E 165F 200 165B 111 110 327 474 140 326 473 475 111 481 141 146 476 22 149 478 479 148 147 170 719 734 752 755 148 47 328 329 302 300 301 718 703 480 481 149 147 46 328 700 732 731 727 730 733 702 726 720 701 720 717 327 326 323 324 325A 146 323 324 326 327 320 470 321 455 143 322 142 130 131 131 133 329 119 114 115 154 135 138 136 137 112 152 155 151 51 55 52 716 292 472 153 291 290 477 471 155 40 1/9 0662-760 753 761 455 765 456 450 461 460 461 458 452 453 459 43 44 45 List of parts 0662--761 SAB 128 R Mk 4 19--1 0173--530--EN

19. Spare Parts Drawings 04.03 4161--T15 S N Y AB B A B I1 I1 A J J AB M1 B N M1 S 2/9 0662-760 List of parts 0662--761 SAB 128 R Mk 4 0173--530--EN 19--2

19. Spare Parts Drawings 04.03 4161--T15 R B B F F C C D D E E A A 3/9 0662-760 Economizer Port 292 291 293 290 SECTION C--C HLI Ports 302 300 SECTION D--D 301 List of parts 0662--761 SAB 128 R Mk 4 19--3 0173--530--EN

19. Spare Parts Drawings 04.03 4/9 0662-760 751 756 755 47 23 46 E C 52 55 51 86 87 SECTION I1--I1 J--J SEE DETAIL A SAB 128 R Mk 4 4161--T15 List of parts 0662--761 0173--530--EN 19--4

19. Spare Parts Drawings 04.03 4161--T15 119 142 143 151 329 328 152 112 138 137 136 135 140 20 111 326 327 5/9 0662-760 SEE DETAIL B MALE FEMALE 90 91 92 93 94 96 44 45 43 40 329 328 153 155 154 114 115 132 133 131 130 141 10 110 26 21 111 95 SECTION S--S N--N List of parts 0662--761 SAB 128 R Mk 4 19--5 0173--530--EN

19. Spare Parts Drawings 04.03 4161--T15 474 473 475 481 476 478 479 455 470 755 458 472 471 480 481 753 452 477 SECTION B--B G--G 460 459 755 453 461 450 456 716 717 6/9 0662-760 List of parts 0662--761 SAB 128 R Mk 4 0173--530--EN 19--6

19. Spare Parts Drawings 04.03 250A 251 252 254 261 762 262 260 266 267 265 267 270 264 269 268 170 718 7/9 0662-760 703 702 719 734 SECTION A--A SAB 128 R Mk 4 4161--T15 List of parts 0662--761 19--7 0173--530--EN

19. Spare Parts Drawings 04.03 165B 165G 81 165J 160 82 83 165A DETAIL B SCALE 1:1 118 165E 165F 165I 165D 165C 165L 165K 113 4161--T15 SECTION M1--M1 200 193 24 25 186 101 103 DETAIL A SCALE 1:1 22 8/9 0662-760 180 183 105 182 104 184 102 100 List of parts 0662--761 SAB 128 R Mk 4 0173--530--EN 19--8

19. Spare Parts Drawings 04.03 4161--T15 G G 733 731 732 730 700 SECTION H--H 727 726 720 701 720 325A 320 148 147 146 149 SECTION F--F 324 323 SECTION E--E 322 321 9/9 0662-760 List of parts 0662--761 SAB 128 R Mk 4 19--9 0173--530--EN

19. Spare Parts Drawings 04.02 4161--T12_0 102 184 183 104 105 186 180 186 250B 251 92 90 82 326 327 86 100 182 23 101 103 327 326 20 25 263 267 755 765 751 762 252 261 271 93 94 96 91 95 87 83 165J 326 327 24 21 26 264 266 269 265 260 270 262 165A 113 81 165K 26 118 193 200 474 268 165L 160 110 473 475 165D 165I 165G 165C 165F 165E 165B 170 140 141 22 479 478 476 481 326 327 148 147 146 149 329 328 111 719 752 755 327 326 47 302 300 700 727 732 726 731 730 720 701 734 718 703 720 480 481 291 293 292 290 323 324 146 325A 149 320 148 147 321 327 322 326 329 328 143 142 46 301 135 136 138 51 55 52 733 702 717 130 131 137 704 716 133 119 132 152 114 115 151 154 1/10 0662-750 753 755 761 477 765 459 456 450 453 452 471 461 460 458 472 470 455 95 153 40 43 44 45 List of parts 0662--751 SAB 163 R Mk 4 0173--530--EN 19--10

19. Spare Parts Drawings 04.02 4161--T12_0 A A D D C C E E B F F 2/10 0662-750 292 290 291 293 302 301 SECTIONC--C 300 List of parts 0662--751 SAB 163 R Mk 4 19--11 0173--530--EN

19. Spare Parts Drawings 04.02 4161--T12_0 86 87 104 180 105 183 184 182 102 100 751 755 756 765 762 101 186 103 193 24 25 200 SECTION K--K L--L 51 55 3/10 0662-750 119 47 46 95 52 List of parts 0662--751 SAB 163 R Mk 4 0173--530--EN 19--12

19. Spare Parts Drawings 04.02 114 151 45 44 115 152 153 40 43 328 329 4161--T12_0 142 143 137 138 136 135 140 10 26 20 111 154 132 133 131 130 141 110 21 26 111 95 91 96 94 93 92 90 SECTION H--H I--I J--J 4/10 0662-750 SEE DETAIL A 165B 165F 165G 165J 82 160 83 113 DETAIL A SCALE 1:1 118 165E 165I 165C 165D 81 165L 165K 165A List of parts 0662--751 SAB 163 R Mk 4 19--13 0173--530--EN

19. Spare Parts Drawings 04.02 4161--T12 474 473 475 481 476 479 478 455 458 470 752 472 480 481 471 452 753 761 477 453 450 461 459 460 456 717 716 SECTION A--A 5/10 0662-750 List of parts 0662--751 SAB 163 R Mk 4 0173--530--EN 19--14

19. Spare Parts Drawings 04.02 4161--T12_0 250B 251 252 260 269 270 268 261 262 266 267 265 263 264 170 703 719 718 733 702 SECTION B--B 6/10 0662-750 List of parts 0662--751 SAB 163 R Mk 4 19--15 0173--530--EN

19. Spare Parts Drawings 04.02 4161--T12_0 733 731 730 732 SECTION G--G 700 727 726 720 720 701 22 SECTION F--F 325A 320 324 323 321 322 SECTION E--E 7/10 0662-750 148 147 149 146 SECTION D--D List of parts 0662--751 SAB 163 R Mk 4 0173--530--EN 19--16

19. Spare Parts Drawings 04.02 W 4161--T12_0 C2 TT7 PT1 A D1 E2 Y B F2 A ø138 8/10 0662-750 22.5 8x ø17.5 BC 250 8x M16X24 135 List of parts 0662--751 SAB 163 R Mk 4 19--17 0173--530--EN

19. Spare Parts Drawings 04.02 4161--T12_0 F1 P H Z G L K E1 I, Q, V D2 C1 94 ECONOMIZER PORT G M8X18 ø35 M10X18 R 10 29.5 30 HLI PORT 9/10 0662-750 List of parts 0662--751 SAB 163 R Mk 4 H R28 R 10 56 78 38 0173--530--EN 19--18

19. Spare Parts Drawings 04.02 4161--T12_0 O M 35 N S S BC ø96 SCALE 1:2 10/10 0662-750 50 ø List of parts 0662--751 SAB 163 R Mk 4 19--19 0173--530--EN