9/0
:: Introduction Thank you for purchasing this Team Associated product. This assembly manual contains instructions and tips for building and maintaining your new RC0 B44.. Please take a moment to read through this manual to help familiarize yourself with these steps. We are continually changing and improving our designs; therefore, actual parts may appear slightly different than in the illustrations. New parts will be noted on supplementary sheets located in the appropriate parts bags. Check each bag for these sheets before you start to build. :: KIT Features The Factory Team B44. is the next generation in a long line of race winning 0th scale 4wd buggies dating back to 003. The B44 project came to life as a cooperative effort between Team Associated and J Concepts Jason Ruona and Brad Reelfs, culminating with Team Associated driver Ryan Cavalieri winning the 005 I.F.M.A.R. World Championships in Italy with the BJ4 World s Edition. The production B44 Factory Team continued the winning ways with Jared Tebo winning the 007 I.F.M.A.R. World Championship in Japan along with Ryan Maifield and Ryan Cavalieri in a --3 B44 podium sweep. Team Associated designers optimized the B44. for the latest generation of racers using LiPo batteries and brushless motors. With the advent of this new technology, R/C cars are lighter and more powerful than ever. The B44. is geared for strictly LiPo batteries, with no cell slots in the chassis and a carbon fiber battery tray as standard equipment. The center section of the battery tray can be replaced with an optional (not included) ballast weight for more rearward weight bias. Motor installation and adjustment is a breeze thanks to the cam motor mount system. The blue aluminum rear hubs add durability and new camber link adjustment options. Lastly, the B44. comes with the latest JConcepts Punisher body and under tray. Features in the B44. Factory Team:.5mm updated carbon fiber chassis for LiPo batteries only Carbon fiber LiPo battery tray with removable center section (*optional ballast weight req d) 3.5 mm front shock tower Updated front top deck for more durability along with new antenna location Cam motor mount set Factory Team 0 degree aluminum rear hubs with oversize outer bearing. Factory Team V dual-cap hard anodized shock bodies with threaded collars V slipper assembly with high-rate spring Factory Team Gold slipper pads JConcepts Punisher body and under tray Pro-Line M3 Holeshot.0 tires Rear anti-roll bar included Bleed-screw shock caps TiN Gold shock shafts front and rear Carbon fiber battery straps with thumb screws /4 locking and 3/ mini locking nuts :: Additional Features B44. F.T. Additional Kit Features: Servo mounted 3mm closer to centerline Chassis cut for additional ground clearance Ball differential with light-weight outdrives Dual-sided externally adjustable slipper clutch CVA joints with pin retainer clips Factory Team blue Titanium turnbuckles Factory Team blue aluminum servo mounts Factory Team blue aluminum wheel spacers Factory Team blue aluminum shock bushings Factory Team blue aluminum shock pivot balls Ball-bearings steering bell cranks Fully adjustable camber, and toe-in Built in servo saver Vertical ball end adjustment front & rear :: Other Helpful Items Silicone Shock Fluid (Refer to catalog for complete listings) Body Scissors (AE Part # 737) Reamer / Hole Punch Wire Cutters Hobby Knife FT Hex Wrenches (AE Part # 54) Needle Nose Pliers Multi Tool (AE Part #7494) Soldering Iron Calipers or a Precision Ruler Green Slime shock lube (AE Part # 05) Associated Electrics, Inc. 0 Commercentre Dr. Lake Forest, CA 930 Customer Service Tel: 949.544.7500 Fax: 949.544.750 http://www.teamassociated.com http://www.rc0.com http://twitter.com/team_associated http://bit.ly/aeonfacebook
3 :: Table of Contents...Cover...Introduction 3...Table of Contents 4...Front / Rear Differential Build 5...Front Gearbox Build...Rear Gearbox Build 7-8...Steering and Center Battery Brace Build / Install 8-9...Front End Build 9...Rear End Build 0...Slipper Build...Center Bulkhead Mounts...Front Top Deck Build -...Rear Top Deck Build 3...Turnbuckles Build 3...Front CVA Build 5...Rear CVA Build 5 -...Rear Suspension Build -7...Rear Anti-Roll Bar Build 7...Battery Tray and Side Body Mounts Build 8-9...Shocks Build 9-0...Servo Build 0...Electronics Install -...Body, Wheel, Tires Install 3-4...Tuning Tips 5-33...Catalog 34...Notes 35...Setup Sheet Kit Setup 3...: Hardware Fold Out 37...Setup Sheet Blank 38...Back Cover 3-4...Front Suspension Build :: Notes This symbols indicates a special note or instruction in the manual. There is a : hardware foldout page in the back of the manual. To check the size of a part, line up your hardare with the correct drawing until you find the exact size. Each part in the foldout has a number assigned to it for ordering replacement parts. Associated Electrics, Inc. 0 Commercentre Dr. Lake Forest, CA 930 Customer Service Tel: 949.544.7500 Fax: 949.544.750 http://www.teamassociated.com http://www.rc0.com http://twitter.com/team_associated http://bit.ly/aeonfacebook
4 :: Front and Rear Differential Build - Step 579 Diff outdrive ring 9734 Diff outdrive, short #59 diff lube 579 Diff outdrive ring #59 diff lube 9734 Diff outdrive, long 909 Diff bearing 394 Bevel diff gear #59 diff lube 58 Diff balls x :: Front and Rear Differential Build - Step Trim any flashing material off of the #330 Locking t-nut ears 330 Locking t-nut 58 Diff spring Kit Setting -/8 Fully tightened position 0 5/4 hex wrench installed in diff bolt -/4-3/4 -/4 909 Diff bearing -3/8-5/8 #588 black grease 574 Thrust balls 573 x Thrust washers 573 Thrust screw x 39 x Diff outdrive shim 397 x Diff outdrive bearing Build two diffs
5 :: Front Gearbox Build - Step 738 CVA coupler #588 black grease 9747 CVA bone center, front #597 ca glue drop Align the gap in the pin retainer to be opposite of the CVA pin. 97 CVA input shaft 799 CVA pin retainer 738 4-40 setscrew Racer s Tip: Try using only drop of CA glue to secure the pin retainer :: Front Gearbox Build - Step 3977 x 3/x3/8 bearing Trim flashing off back of gear. Align the slot in the pinion gear with the pin 39 x Drivetrain shim 3903 Shaft pinion gear 399 Input shaft pin 99 E-clip :: Front Gearbox Build - Step 3 80 x FT shcs aluminum, blue #59 diff lube drop 9733 Upper transmission case #59 diff lube drop 9733 Lower transmission case
:: Rear Gearbox Build - Step #588 black grease 738 CVA coupler 97 CVA input shaft 799 CVA pin retainer #597 ca glue drop Align the gap in the pin retainer to be opposite of the CVA pin. 970 CVA bone center, rear 738 4-40 setscrew Racer s Tip: Try using only drop of CA glue to secure the pin retainer :: Rear Gearbox Build - Step 39 x Drivetrain shim 3977 x 3/x3/8 bearing 3903 Shaft pinion gear Align the slot in the pinion gear with the pin 399 Input shaft pin 99 E-clip :: Rear Gearbox Build - Step 3 #59 diff lube drop 80 x FT shcs aluminum, blue 9733 Upper transmission case #59 diff lube drop 9733 Lower transmission case
7 :: Steering and Center Battery Brace Build Step 9744 x Steering post 9743 x Servo saver upper 9743 Steering v-spacer 9743 Spring retainer 7 Dust cover foam 9743 Servo saver lower 9744 Servo saver spring 9744 x 5-40 locknut 7 Ballstud short, silver mm 930 x.030 washer 77 x Ballstud long, silver 7 x Foam dust cover 9743 Steering rack :: Steering and Center Battery Brace Build Step 3874 x Black carrier bushing 97 x 974 x Steering bearing set 9743 Steering retainer column 9774 B44. LiPo chassis 9 x fhcs Use the small hole bearings :: Steering and Center Battery Brace Build Step 3 9 fhcs 9743 Steering retianer top Use the large hole bearings 974 x Steering bearing set
8 :: Steering and Center Battery Brace Build / Install Step 4 47 x Shock mount nuts 9775 B44. LiPo battery tray 9 x fhcs :: Front End Build - Step 4449 4-40x3/ aluminum locknut 973 Front bulkhead 975 4-40x7/ fhcs 9 x fhcs 9 x fhcs :: Front End Build - Step 97 x Front inner hinge pin #59 thread lock 945 x -5x/8 974 Shock tower mounts 975 x Front arm
9 :: Front End Build - Step 3 743 x 4-40x3/4 780 x Shock bushing 978 Front bumper th #5 re ad 9 lo ck 97 x 9703 Front shock tower 97 x :: Rear End Build - Step 4449 4-40x3/ aluminum locknut 97 Rear chassis plate 93 x #4 washer 4449 x3 4-40x3/ aluminum locknut 978 Rear bumper 97 Rear chassis brace 773 4-40x5/ fhcs 975 4-40x7/ fhcs 95 x 4-40x5/8 fhcs :: Rear End Build - Step 97 x Rear inner hinge pin 9 x4 fhcs 945 x -5x/8 974 x Rear arm
0 :: Slipper Build - Step Side view flanges 973 Slipper shaft 97 Center bearing 973 insert Slipper spring retainer 7935 3/x/ bearing 97 Center bearing insert 7485 x FT V slipper hubs 95 8T 48P spur gear 903 Slipper pad 7935 3/x/ bearing x Side view flange 973 slipper drive cup spacer :: Slipper Build - Step 738 x 4-40 setscrew 54 Solid pin 974 Slipper drive cup #588 black grease Insert #974 Slipper nut o-ring all the way into the #9740 Slipper nut before installing the slipper nut to the slipper shaft 748 FT V slipper spring Rub black grease on o-ring before install 9740 Slipper nut 974 Slipper nut o-ring :: Slipper Build - Step 3 0mm Check slipper after running Adjust as needed. 974 Slipper drive cup 974 Slipper drive cup o-ring 54 Solid pin
:: Center Bulkhead Mounts - Step 9 4-40x/4 fhcs 980 FT cam motor mount 9709 Center bulkhead Set remaining motor mount pieces aside Slipper assembly Install #59 thread lock 9 x3 fhcs Key CVA bones in the slipper outdrives :: Front Top Deck Build - Step 4449 x 979 970 4-40x3/ Body Top deck aluminum mount front locknut 974 Shock tower mount 4334 x -5x5/ 9 x5 fhcs #59 thread lock 93 x Washers, aluminum #4 88 4-40x/4 77 x Ballstud long, silver 97 x 33 Antenna mount :: Front Top Deck Build - Step :: Rear Top Deck Build - Step 4449 x 4-40x3/ aluminum locknut 970 Top deck rear 97 x 93 x Washers, aluminum #4 77 x Ballstud long, silver
:: Rear Top Deck Build - Step 9 x fhcs 9704 Shock tower rear 974 Shock tower mount 97 x th #5 re ad 9 lo ck 979 Body mounts 94 x shcs 743 x 4-40x3/4 780 x Shock bushing :: Rear Top Deck Build - Step 3 95 x3 4-40x/ shcs 7738 x 4-40x7/8 shcs 979 x Wing mount (right, left) 4449 4-40x3/ aluminum locknut :: Rear Top Deck Build - Step 4 97 x 94 x4 shcs 97 Center bulkhead cap th #5 re ad 9 lo ck th #5 re ad 9 lo ck
3 :: Turnbuckles Build - Step Front Steering Link 404 FT titanium turnbuckles.77 Front Camber Link Rear Camber Link 40 FT titanium turnbuckles.00 40 FT titanium turnbuckles.00 730 x Ball cups, large 730 x Ball cups, large 730 x Ball cups, large 0mm 4.5mm 7mm Steering Build x Front Camber Build x Rear Camber Build x :: Front CVA Build - Step 9747 CVA bone front 738 CVA cross pin Align the gap in the pin retainer to be opposite of the CVA pin. #597 ca glue drop #588 black grease 738 CVA coupler 9748 CVA axle front 799 CVA pin retainer Build x :: Front Suspension Build - Step 7 x Foam dust cover 77 x Ballstud long, silver Right Side Left Side 975 x Bearing crush tube Right Side 4449 x 4-40x3/ aluminum locknut 97 x Steering block (right, left) 3977 x4 3/x3/8 bearing Left Side
4 :: Front Suspension Build - Step 739 x Axle pin Left Side 7 x Dust cover foam 4449 x 4-40x3/ aluminum locknut Right Side Right Side 9750 x Axle drive hex 3983 x Ballstud long, black 970 x Caster block (right, left) Left Side :: Front Suspension Build - Step 3 Left Side Right Side Left Side Right Side 947 x4 Steering block bushing x4 4-40x7/ :: Front Suspension Build - Step 4 Front steering link 945-5x/8 97 Hinge pin set Orient the notch to the left throughout the car. It indicates which end has the left hand threads Build x (right and left side) Front camber link Install x (right and left side)
5 :: Rear CVA Build - Step 9754 CVA bone rear #588 black grease 738 CVA cross pin #597 ca glue drop Align the gap in the pin retainer to be opposite of the CVA pin. 9755 CVA axle rear 738 CVA coupler 799 CVA pin retainer Build x :: Rear Suspension Build - Step Right Side 984 x FT aluminum hub (0 ) Left Side 3977 x 3/x3/8 bearing 7935 x.87x0.50x.9 bearing Build x (right and left side) 7933 x Crush tube :: Rear Suspension Build - Step Right Side 3983 x Ball stud long (black) Molded camber link tower A has standard holes, and optional B tower has in-between hole options 987 x FT aluminum hub tower (A) Left Side A 7 x Dust cover foam Build x (right and left side) 93 x4 4-40x5/ shcs
:: Rear Suspension Build - Step 3 739 / roll pins 908 Rear axle wheel spacer 945-5x/8 Add shim here if needed. 930.030 ballstud washer 38 Aluminum ballstud washer, mm 97 Hinge pin set 738 x 3/ axle shims Build x (right and left side) :: Rear Suspension Build - Step 4 Rear camber link Orient the notch to the left throughout the car. It indicates which end has the left hand threads Install x (right and left side) :: Rear Anti Roll Bar Build - Step 8830 Anti roll bar pivots 888 Anti roll bar cups mm 9780 x 4-40x/ set screw Build x 888 Ball cup, short Install x (right and left side)
7 :: Rear Anti Roll Bar Build - Step 4334 x -5x5/ 9780 x Washer 9780 0.55 silver anti-roll bar Optional black anti-roll bar also included 95 x 4-40x/8 setscrew Install anti-roll bar into #8830 antiroll bar pivots until the bar is flush with the end of the pivot :: Battery Tray and Side Body Mounts Build - Step 970 Battery post x4 Threadlock all setscrews 9745 x4 4-40x.5 setscrew #59 thread lock Trim side body mounts as shown before installation 979 x B44 body mounts 9775 LiPo battery tray x #59 thread lock 9 x4 fhcs 773 x 4-40x5/ fhcs
8 :: Shocks Build - Step 49 Shock cap o-ring 7475 Front shock body 0.89 7484 Shock internal spacer Front, Build x 49 Shock cap o-ring 7479 Rear shock body.8 5407 x O-ring #05 green slime 7484 Lower shock seal cap 7484 Shock internal spacer Rear, Build x 45 Shock piston (#) 45 Shock piston (#) 973 FT shock shaft gold 0.80 47 5407 O-ring #05 green slime x 7484 Lower shock seal cap 99 e-clip x Front, Build x FT shock shaft gold.0 99 e-clip x Rear, Build x :: Shocks Build - Step Front, Build x 487.030 nylon washer Rear, Build x 777 Shock eyelet 777 Shock eyelet 487.030 nylon washer Front, Build x Rear, Build x 777 FT shock pivot ball Front, Build x 777 FT shock pivot ball Rear, Build x :: Shocks Build - Step 3 Step -3 Shock oil Front Shock: 35 wt Rear Shock: 30 wt Step 4-5 Shock oil Step -7 443 x4 Bleeder shock cap (molded) Step 8 Shock Bleeding Steps:. Before assembly, get each bleed screw and thread it - turns into the shock cap. This will make installation easier when you are bleeding your shocks.. Pull shock shaft down. 3. Fill shock body 3/4 full with silicone shock fluid. 4. Slowly move the shock shaft up and down to remove air from under the piston. 5. Wait for bubbles to come to surface.. Fill shock body to top with silicone shock fluid. 7. Place a drop of oil in the cap and on cap threads. 8. Install cap (without bleed screw) and tighten completely. 9. Slowly compress shaft all the way to bleed excess silicone shodk fluid out the hole in the cap (use rag aroundshock to catch excess fluid). 0. Install -5 button head screw until snug while shaft is fully compressed (recommend using a high quality.050 wrench such as Factory Team #54). 945 x4-5x/8 Step 9-0
9 :: Shocks Build - Step 4 74 Shock collar o-ring x4 mm.7mm 74 Shock collar x4 Build two front shocks Build two rear shocks 480 x Front Spring, Silver, 3.85lb 480 x Rear Spring, Green,.90lb 974 x Front offset spring cup 475 x Rear spring cup :: Shocks Build - Step 5 47 x Shock mount nut Use inside hole in rear arm Use outside hole in front arm 95 x 4-40x/ shcs 47 x Shock mount nut 95 x 4-40x/ shcs :: Servo Build - Step 398 Servo screw Ballstud not included.0 black, short Servo not included Offset the servo horn by 5-0 degrees (approximately one notch) 779 x FT Servo mount 980 Servo horn 7 Dust cover 89007 foam Servo horn ring 97 x 7337 Gold washer x4 733 Servo spacers x
0 :: Servo Build - Step :: Electronics Install - Step 79 Servo Link 338 Antenna tube & cap 0.5m 9 x fhcs Receiver not included :: Electronics Install - Step Loosen mesh Tighten mesh Set gear mesh 980 FT Motor mount clamp Pinion and setscrew not included 980 x Steel washer Motor tabs should clear top deck 9803 FT Motor Mount Cam Motor not included 980 4-40x.00 setscrew 353 x M3xmm :: Electronics Install - Step 3 787 x FT body clips, blue 978 x Battery strap, carbon fiber LiPo batteries not included ESC not included See ESC manufacturer s instructions for wiring 95 x 4-40x/ shcs
:: Body, Wheels, Tires Install - Step 97 #5 ue gl ca 97 #5 ue gl ca Carefully apply tire adhesive to the tire bead on both sides. Do one side at a time, allow it to dry before gluing the other side 9589 x. Wheel, rear 9590 x Proline Holeshot.0 M3 compound 977 x w/ insert, rear. Wheel, front 979 x Proline Holeshot.0 M3 compound w/ insert, front :: Body, Wheels, Tires Install - Step 95 x 8-3 locknut, steel 953 x 8-3 LP steel locknut :: Body, Wheels, Tires Install - Step Punisher undertray by Jconcepts Add hole Add hole Trim along lines Slide undertray in between the front bumper and the chassis Add hole 3mm or.5 holes on marks
:: Body, Wheels, Tires Install - Step 3 Use the screw for the servo mount for the opposite side 47 nylon nut 773 4-40 x 5/ fhcs 773 4-40 x 5/ fhcs 978 Rear bumper :: Body, Wheels, Tires Install - Step 4 Punisher body by JConcepts Painting Tips: Body : Your B44. FT comes with a clear polycarbonate body. You will need to prep the body before you can paint it. Wash the inside thoroughly with warm water and liquid detergent. Dry the body using a clean, soft, lint-free cloth. Use the supplied window masks to cover the windows from the INSIDE of the body (RC cars get painted from the inside). Using high quality masking tape, apply tape to the inside of the body to create a design. Spray (either rattle can or airbrush) the paint to the inside of the body (prefferably dark colors first, lighter colors last). NOTE: use ONLY paint that is recommended for use with (polycarbonate) plastics. If you don t, you can destroy the plastic body). 73 x FT body clips, blue After painting, cut the body along the trim lines. Make sure to drill or use a body reamer to make the holes for the body mounts and antenna :: Body, Wheels, Tires Install - Step 5 73 x FT body clips, blue 979 x Wing shims 977 High downforce wing,.5
3 :: Tuning Tips Tips for Beginners: Before making any changes to the standard setup, make sure you can get around the track without crashing. Changes to your vehicle will not be beneficial if you can t stay on the track. Your goal is consistent laps. Once you can get around the track consistently, start tuning your vehicle. Make only ONE adjustment at a time, testing it before making another change. If the result of your adjustment is a faster lap, mark the change on the included setup sheet (make adddtional copies of the sheet before writing on it). If your adjustment results in a slower lap, revert back to the previous setup and try another change. When you are satisfied with your vehicle, fill in the setup sheet thoroughly and file it away. Use this as a guide for future track days or conditions. Differential: Adjust the differential (AKA diff for short) as noted in the assembly instructions. Adjusting the rear diff is not meant to be a tuning option. If you can hear the diff making a barking or chirping sound on jump landings or under acceleration, either your diff is set too loose or your slipper clutch is set too tight. The front diff can go out / turn to get more steering. Slipper Clutch: The assembly instructions give you a base setting for your clutch. To preserve the differentials, always start with the slipper on the loose side and slowly tighten the adjustment nut until it is set. To adjust the slipper, remove the body and insert a mm (or 5/4 ) hex wrench through the center of the top deck (or through the bottom slot in the chassis). Then, grab both of the rear wheels and rotate forwards to tighten and backwards to loosen. As you spin the wheels, you ll feel the motor click every ¼ of a wheel revolution. At the track, tighten or loosen the nut in click increments until you hear only a faint slipping sound for - feet on takeoffs. Front Camber Link Length & Number of Washers Under Ballstud: Changing the length of the camber link is considered a bigger step than adjusting the ballstud height. Typically shortening the camber link (orlowering the ballstud) will give the front end less roll and quicken steering response. Lengthening the camber link (or raising the ballstud) will give the front more roll and slower steering response. To raise the ballstud, remove washers from between the ballstud and upper deck. Front Camber: A good starting camber setting is degrees. Use the included #79 camber gage to set your camber. Positive camber, where the top of the tire is leaning out, is typically not recommended. Front Toe-In: Zero degree toe-in (tires pointing straight forward) is the setting that should be used in almost all track conditions. Occasionally you can increase turn in by adding a little toe-out (front of tires point slightly out). Front toe in is not a typical tuning adjustment used by The Team. Front Arm Hole: The kit silver springs and outside front arm hole will work best in most cases. Moving the shock to the inside hole on the front arm requires you to add another down travel limiter to the front shocks, so there should be two down travel limiters in each shock. You should also change to a stiffer spring to account for the difference in leverage on the shock. Front Ride Height: The standard front ride height setting is mm. Check the ride height by lifting up the entire car about 8- inches off the bench and drop it. After the suspension settles into place, raise or lower the shock collars as necessary until there is mm gap from the bottom of the chassis to the ground. Anti-Squat: Anti-squat denotes the angle of the rear arms relative to the ground. Zero anti-squat means that the rear arms are flat, parallel with the ground. The kit setting is degrees, and can be reduced to degree by removing the included #4 washer underneath the arm mount. You can add another #4 washer so that there is two washers underneath the arm mount to get 3 degrees of anti-squat. Adding anti-squat tends to make the car rotate more in corners, but doesn t handle as well through the bumps. degree will be better in bumpy sections. Rear Camber Link Length & # of Washers under Ballstud: Changing the length of the camber link is considered a bigger step than adjusting the ballstud height on the rear chassis brace. Typically shortening the camber link (or lowering the ballstud) will give the rear end less roll and the car will tend to accelerate or square up better. Lengthening the camber link (or raising the ballstud) will give the rear more roll and more cornering grip. To raise the ballstud, remove washers from in-between the ballstud and upper deck. You should normally use the kit setting and only adjust the ballstud height
4 :: Tuning Tips (cont.) Rear Hub Spacing: You have 3 options for rear hub spacing, FORWARD, MIDDLE, & BACK. The kit setting is FORWARD, which provides the most rear traction and will be used most often. For improved handling in bumps or rhythm sections, try moving the hubs to MIDDLE or BACK. This can also make the car handle better in 80 turns. Rear Anti-Roll Bar: The #9780 B44 anti-roll bar kit (a.k.a. swaybar) allows you to add roll resistance to the rear end with minimal effect on handling over bumps and jumps. The anit-roll bar is very helpful when trying to tune the suspension. The black bar is the softest (.047 wire) and the silver (.055 wire) is the standard. It is popular to run a rear anti-roll bar in 4wd to help the car square up more out of turns. Rear Arm Hole: The inner hole in the arm tends to work the best over the bumps and jump sections. Changing to the outer hole in the rear arm will tend to make the rear end feel more locked in and less responsive. Making this change to the outer hole requires you to remove the downtravel limiters from the rear shocks. Rear Ride Height: The rear ride height setting you should use most often is 0 mm (the rear arms appear level when looking from the rear). Check the ride height by lifting up the entire car about 8- inches off the bench and drop it. After the suspension settles into place, raise or lower the shock collars as necessary until there is 0 mm gap from the bottom of the chassis to the ground. Note: Check the ride height gap at the rear end of the carbon fiber chassis, not at the rear chassis plate which is raised for more ground clearance. The chassis should look level from the side. Battery Setup: The B44. is designed to use LiPo saddle pack batteries. Follow your ESC and battery manufacturer s recommendations for wiring. Setup Sheets: Most often, the best way to get your car handling right is to go to our website www.rc0.com and click on the links to Setup Sheets, then RC0B44. setups. Our team of professional drivers help develop these setups at National events. Also, most drivers have a base setup that they use as a starting point for every event. Try running some of our base setups OR look for track conditions and tires that are similar to your local track and mimic that setup. Remember, each adjustment has a purpose, so copy everything from the setup sheet and then make adjustments based on the recommendations in this manual. Steering Servo Chart Associated XP-05, XP-33 Airtronics 940 Airtronics Hitec Hitec JR JR Futaba Futaba Futaba KO 94738, 9457, 9458, 9457, 9458, 94357, 94358, 9445, 94453, 9475, 94755 HS-55MG, HS-545MG, HS5MG, HS45MG HS-3HD, HS-35HB, HS-95, HS-985MG, HS-595, HS-5985MG, HS-45BB, HS-4 Z475, Z4750, Z750, Z8450, Z8550, NES-4750 Z50, Z550 S904, S950, S9450, S48 S3003, S90, S90 S9404 PS-40, PS-00, PS-004, PS-05, PS-73, PS-74, PS-3, PS-43, PS-44 # 980 servo arm F A A H H J J F F F J * Not all servo s are listed * Make sure servo linkage clears the servo through full travel in both directions. Use #733 servo spacers to adjust the servos position
5 :: Shocks 777 780 487 5407 99 47 443 45 49 47 475 95 7474 7475 7478 7479 7484 945 973 974 FT Blue Aluminum Shock Pivot Ball/Eyelet FT Blue Aluminum Shock Bushing, std.030 Nylon Washer Red O-Rings /8 E-Clips FT Shock Shaft Gold.0 Bleeder Shock Caps /0 w/screws Shock Pistons, 4 each of #,, & 3 Black Shock Cap O-Ring Shock Mount Nut Spring Cup (used on rear) 4-40 x / SHCS V Threaded Shocks 0.89 Complete V Threaded Shock Bodies 0.89 V Threaded Shocks.8 Complete V Threaded Shock Bodies.8 V /0th Shocks Rebuild Kit (rebuilds 4) -5 x /8 FT Shock Shaft Gold 0.80 Offset Spring Cups (used on front) 4 4 8 4 4 4 4 :: Differentials 330 39 394 397 573 574 579 58 58 909 9734 Diff T-nut Trans. Shim Set Differential Ring Gear & Drive Pinion Gear 3/8 x 5/8 RS Ball Bearing Diff Thrust Washer & Bolt 5/4 Diff Thrust Balls Diff Drive Rings 3/3 Carbide Diff Balls Diff Thrust Spring Diff Bearing 3/ x 5/ B44 Outdrives, Set 397 58 394 :: Shock Springs 58 58 493 494 49 497 83 478 480 48 48 7434 7435 743 :: Lubes & Adhesives / Decals / Misc. 05 59 597 588 59 3 77 7 77 38 380 3834 9777 47 443 49 Front 7475 Rear 7479 5407 7484 5407 7484 780 945 45 487 Front 973 Rear 47 Factory Team Buggy Front Spring Kit. I pair of green, silver, blue, black front springs Factory Team Truck Rear Spring Kit. I pair of green, silver, blue, gold, red rear springs Front Buggy Spring Brown.80 lb (Kit) Front Buggy Spring Green 3.50 lb Front Buggy Spring Silver 3.85 lb Front Buggy Spring Blue 4.0 lb Front Buggy Spring Black 3.0 lb Rear Spring Silver.0 lb Rear Spring Green.90 lb (Kit) Rear Spring Black.74 lb Rear Spring Gray.33 lb Rear Spring Blue.55 lb Rear Spring Gold.75 lb Rear Spring Red.95 lb FT Green Slime Shock Lube FT Locking Adhesive FT Tire Adhesive, medium Black Grease - 4cc S.Diff Lube - 4cc Silicone Grease - 4cc Servo Tape Reedy 009 Sticker Set Reedy Powered Logo Decal American Bumper Sticker AE Logo Decal Sheet AE Blue Embossed Logo Sticker B44. Decal Sheet 99 99 74 74 Front 974 Rear 475 95 777 777 :: Shock Oil 540 54 54 543 544 545 54 547 548 549 5430 543 543 5433 5434 5435 543 5437 5438 39 39 330 58 9734 579 909 0 Weight Silicone Shock Oil 0 Weight Silicone Shock Oil 30 Weight Silicone Shock Oil 40 Weight Silicone Shock Oil.5 Weight Silicone Shock Oil 80 Weight Silicone Shock Oil 7.5 Weight Silicone Shock Oil 5 Weight Silicone Shock Oil 5 Weight Silicone Shock Oil 35 Weight Silicone Shock Oil 45 Weight Silicone Shock Oil 55 Weight Silicone Shock Oil 3.5 Weight Silicone Shock Oil 37.5 Weight Silicone Shock Oil 4.5 Weight Silicone Shock Oil 50 Weight Silicone Shock Oil 0 Weight Silicone Shock Oil 70 Weight Silicone Shock Oil 47.5 Weight Silicone Shock Oil 909 579 9734 573 573 573 39 39 39 39 397 oz. oz. oz. oz. oz. oz. oz. oz. oz. oz. oz. oz. oz. oz. oz. oz. oz. oz. oz. 574
:: Slipper / Spur Gears / Pinions 54 738 7485 748 7935 903 949 950 95 95 953 97 973 9740 974 FT Axle Pins CVD Rebuild Kit FT V Slipper Hubs FT V Slipper Spring and Washer.87 x.50 x.9 Bearing Slipper Pad 7T 48P Spur Gear 75T 48P Spur Gear 8T 48P Spur Gear (Kit) 78T 48P Spur Gear 84T 48P Spur Gear B44 Bearing Insert B44 Slipper Shaft B44 Slipper Nut B44 Slipper Drive Cups 4 973 7935 97 973 738 974 54 738 95 7485 903 903 974 974 9740 97 748 974 54 973 7485 7935 :: Pinions 85 853 854 855 85 857 858 859 80 8 8 83 84 85 8 87 88 89 5T 48P Pinion Gear T 48P Pinion Gear 7T 48P Pinion Gear 8T 48P Pinion Gear 9T 48P Pinion Gear 0T 48P Pinion Gear T 48P Pinion Gear T 48P Pinion Gear 3T 48P Pinion Gear 4T 48P Pinion Gear 5T 48P Pinion Gear T 48P Pinion Gear 7T 48P Pinion Gear 8T 48P Pinion Gear 9T 48P Pinion Gear 30T 48P Pinion Gear 3T 48P Pinion Gear 3T 48P Pinion Gear :: Anti-Roll Bars :: Turnbuckles 95 888 8830 9780 4-40 x /8 Set Screw Anti Roll Bar Cups, Set Anto Roll Bar Pivots (with setscrews), Set B44 Anti Roll Bar Kit 404 40 730 FT Blue Titanium Turnbuckles.775 / 45mm FT Blue Titanium Turnbuckle.00 / 5mm Ball Cups, Large 888 9780 95 8830 9780 730 404 730 888 95 8830 888 40 730 730 9780 888 40 730 730
7 :: Front and Rear Gearboxes 3903 39 399 3977 4334 99 80 738 799 9733 9747 970 97 9780 Drive Pinions Trans. Shim Set Input Shaft Hardware 3/ x 3/8 RS Ball Bearing -5 x 5/ BHCS /8 Small E-Clips FT 4-40 x 3/8 SHCS, blue CVD Rebuild Kit Posilock QC Pin Retainer B44 Transmission Case B44 Front CVA Bone B44 Center Bone, Rear B44 CVA Input Shaft B44 Anti Roll Bar Kit 8 80 80 80 9733 39 3903 99 80 80 80 738 97 39 799 3977 399 738 9747 80 80 80 80 80 80 4334 9780 4334 9780 9733 99 3903 3977 799 399 738 738 97 39 9733 970 9733 :: Steering 779 3874 398 7 7 77 9 97 733 7337 79 980 930 9743 9744 974 89007 FT Servo Mount, blue Block Carrier Bushings Ballstud.0 Black, short Foam Ballend Dust Covers Ballstud.0 Silver, short Ballstud.30 Silver, short 4-40 x 3/8 FHCS 4-40 x 3/8 BHCS Steering Servo Mount Kit.50 x.5 x.05 Washer Steering Servo Link Servo Horns, Molded Ballstud Washer B44 Steering Set B44 Steering Hardware B44 Steering Bearing Set Steering Servo Ring, blue 0 4 8 4 0 3874 9743 9743 9743 974 9744 9743 97 930 97 77 7 930 77 9744 7 9 9744 9 974 9744 9744 974 9743 7 7 9743 9744 398 980 733 7337 779 89007 733 97 9 97 97 97 7337 7 79 79 79 779 9 :: Front and Rear Shock Towers 73 780 4449 97 743 7738 7874 9703 9704 979 979 977 FT Body Clips, Short, blue FT Blue Alum. Shock Bushing, std 4 4-40 x 3/ Alum. Locknut 5 4-40 x 3/8 BHCS 4-40 x 3/4 BHCS 4-40 x 7/8 SHCS 4-40 x 7/ SHCS 8 B44 Front Shock Tower B44 Rear Shock Tower B44 Body Mounts B44 Wing Mounts High Downforce Wing.5 743 97 97 97 97 780 780 743 97 9703 979 7874 743 979 9704 743 979 780 97 4449 73 73 977 979 979 7738
8 :: Front and Rear Top Plates 73 4334 4449 77 88 9 338 97 95 93 970 970 974 979 33 FT Body Clips, Short, blue -5 x 5/ BHCS 4-40 x 3/ Alum. Locknut Ballstud.30 Silver, short 4-40 x /4 BHCS 4-40 x 3/8 FHCS Antenna Tube, black 4-40 x 3/8 BHCS 4-40 x / SHCS Washers, Alum. #4 B44 Front Top Deck B44 Rear Top Deck B44 Shock Tower Mounts B44 Body Mounts Antenna Mount 8 5 0 338 9 95 974 4449 970 95 95 4449 9 9 9 979 73 4334 9 9 4334 33 9 77 93 93 974 77 4449 970 93 4449 88 77 93 97 97 77 :: Center Bulkhead and Motor Mount 9 94 95 9709 97 9800 980 980 9803 353 4-40 x 3/8 FHCS 4-40 x 3/8 SHCS 4-40 x / SHCS B44 Center Bulkhead B44 Center Bulkhead Cap B44 FT Cam Motor Mount Set B44 FT Cam Motor Mount B44 FT Motor Mount Clamp B44 FT Motor Mount Cam M3 x mm BHCS 95 95 980 980 980 980 9803 94 94 94 94 97 353 353 9 9709 9800 9 980 9 9
9 :: Front Suspension 3977 3983 4449 7 77 953 739 738 799 945 947 975 97 970 97 9747 9748 9750 975 4-40 x 7/ BHCS 3/ x 3/8 RS Ball Bearing Ballstud.30 Black, short 4-40 x 3/ Alum. Locknut Foam Ballend Dust Covers Ballstud.30 Silver, short 8-3 LP Steel Locknut / Universal Roll Pins CVD Rebuild Kit PosiLock QC Pin Retainer -5 x /8 BHCS B44 Steering Block Bushing B44 Front Arms B44 Hinge Pin Set B44 Caster Block B44 Steering Block B44 Front CVA BoneB44 Front CVA Axle B44 Axle Drive Hex B44 Front Crush Tube 5 8 4 4 9747 738 738 739 9748 3983 799 7 970 975 4449 947 3977 947 7 97 77 4449 975 9750 97 3977 945 97 953 :: Rear Suspension 3977 3983 7 93 95 738 739 738 7933 7935 799 908 930 945 97 9754 974 984 987 38 3/ x 3/8 RS Ball Bearing Ballstud.30 Black, short Foam Ballend Dust Covers 4-40 x 5/ SHCS 8-3 Locking Nut, Steel 3/ Axle Shims / Universal Roll Pins CVD Rebuild Kit Crush Tube GT.87 x.50 x.9 Bearing PosiLock QS Pin Retainer RR Axle Wheel Spacer Ballstud Washer -5 x /8 BHCS B44 Hinge Pin Set B44 Rear CVA Bone B44 Rear Arm B44 FT Aluminum Hub, 0 B44 FT Aluminum Hub Tower Set Alum. Ballstud Washer (mm, mm) 8 4 4 0 4 ea. 9754 738 738 3983 7 739 93 799 3977 987 38 930 7933 984 738 7935 97 974 908 95 945 97
30 :: Chassis and Battery Mounts 787 4449 9 47 95 97 93 773 945 970 973 974 978 979 97 9745 975 9774 9775 978 FT Battery Strap Thumbscrews 4-40 x 3/ Alum. Locknut 4-40 x 3/8 FHCS Shock Mount Nuts 4-40 x 5/8 FHCS 4-40 x 3/8 BHCS Washers, Alum. #4 4-40 x 5/ FHCS -5 x /8 BHCS B44 Battery Post B44 Front Bulkhead B44 Shock Tower Mounts B44 Front & Rear Bumper B44 Body Mounts B44 Rear Chassis Plate, 3 arm mount B44 Servo Link and Setscrew 4-40 x 7/ FHCS B44. LiPo Chassis B44. LiPo Battery Tray B44 Battery Strap Carbon Fiber 5 4 0 4 ea. 787 787 978 47 9745 47 9775 9 9 9745 970 970 787 787 978 9745 4449 9775 9 9745 970 974 973 9 9 970 9 9775 945 975 9 978 9 97 9 97 47 773 773 979 9 4449 97 93 93 4449 4449 4449 945 978 773 979 97 9 9774 773 9 95 9 975 95
3 :: Factory Team and Option Parts 404 40 4 598 54 78 79 730 73 73 733 73 777 779 780 787 47 903 90 937 943 74 7474 7475 7478 7479 7484 799 908B 970 97 973 9774 9775 977 9779 9783 9784 978 9787 9795 979 9797 9798 9799 9800 980 980 9803 984 985 98 987 987 Ti Turnbuckle.775 Blue Ti Turnbuckle.00 Blue Ti Turnbuckle 0.75 Blue FT Blue Aluminum Shock Cap FT Solid Axle Pins FT HD Front One-Way Set FT HD One-Way Housing Set FT HD One-Way Outdrive Cup FT Bearings for HD One-Way FT HD One-Way Ring Gear FT HD One-Way Shims FT Short Body Clips Blue FT Blue Aluminum Ball/Eyelet Set FT Servo Mount Blue Aluminum FT Aluminum Shock Bushing Battery Strap Thumbscrew FT Shock Shaft Gold.0 3/8 x 5/8 PTFE Bearings 3/ x 3/8 PTFE Bearings FT Blue 4-40 Locknuts FT Blue 8-3 Locknuts Threaded Shock Collar FT V.89 Threaded Shocks FT V.89 Threaded Bodies FT V.8 Threaded Shocks FT V.8 Threaded Bodies FT V :0 Shock Rebuild Kit CVA Pin Retainer RR Axle Wheel Spacer, blue B44 Alum. Center Bulkhead B44 Alum. Caster Blocks FT Shock Shaft Gold 0.80 B44. LiPo Chassis B44. LiPo Battery Tray B44. LiPo Ballast Weight B44 Complete Bearing Set B44 Alum. Front Tower Mount B44 Alum. Rear Tower Mount B44 Carbon Battery Strap Chassis Protective Sheet Ti Nitride Ballstuds 4-40 x 0.0 Long Ti Nitride Ballstuds 4-40 x 0.30 Long Ti Nitride Ballstuds 4-40 x 0.40 Long Ti Nitride Ballstuds 4-40 x 0.0 Short Ti Nitride Ballstuds 4-40 x 0.30 Short B44 Cam Motor Mount Set B44 Cam Motor Mount B44 Motor Mount Clamp B44 Motor Mount Cam B44 FT Aluminum Hub, 0 B44 FT Aluminum Hub, 0.5 B44 FT Aluminum Hub, B44 FT Aluminum Hub,.5 B44 FT Aluminum Hub Tower Set :: XP Electronics 907 95 9 93 940 94 9 977 909 90 9 9 9 9 S903 Metal Gear Set S903MG Servo S008MG Servo SHV504MG Servo XP SC00 Brushed ESC XP SC450-BL Brushless ESC XP DS33 Digital Servo XP DS05 Digital Servo Gear Set, DS33 Gear Set, DS05 Servo Case, DS33 / DS05 Accessory Pack, DS33 / DS05 XP3SS.4GHz Radio System TRS40SS.4GHz 4Ch Receiver 4 8 4 4 :: Reedy Motors and ESC s 9 97 98 99 93 937 938 939 :: Reedy Batteries 30 303 7 3 33 34 37 8 70 7 :: Reedy Accessories 05 0 54 55 5 57 58 59 0 3 4 7 SP35M SP35L SP35XL SP35XXL SP35XXXL SP3M SP3L SP3XL SP3XXL SP3XXXL SP47 SP48 540R Brushless Motor 3300kV 540R Brushless Motor 3900kV 540R Brushless Motor 4900kV 540R Brushless Motor 00kV XP SC450-BL/Reedy 540R 3300kV Combo XP SC450-BL/Reedy 540R 3900kV Combo XP SC450-BL/Reedy 540R 4900kV Combo XP SC450-BL/Reedy 540R 00kV Combo AA Alkaline.5V (4) AA 700mAh NiMH.V Rechargeable LiPo 0C 500mAh 7.4V SP TX Lightweight Battery 350mAh.V TX Battery - 3PK, M 3000mAh.V TX Battery - Helios, Z 400mAh.V TX Battery - MX 500mAh 7.4V LiPo 40C+ 400mAh 7.4V SP LiPo 500mAh 7.4V 35C SP ROAR Spec LiPo 400mAh 7.4V 35C SP EFRA Spec Motor Cooling Fans () AC/DC NiMH Peak Charger 4.0mm plugs (M, F) 4.0mm plugs (M, 0F) 4.0mm plugs (0F) 4.0mm plugs (00F) 4.0mm plugs (0M) 4.0mm plugs (30M) 3.5mm plugs (3M, 3F) 3.5mm plugs (0F) 3.5mm plugs (00F) 3.5mm plugs (0M) 3.5mm plugs (30M) Reedy 09 Decal Set Reedy Logo T-Shirt - White M Reedy Logo T-Shirt - White L Reedy Logo T-Shirt - White XL Reedy Logo T-Shirt - White XXL Reedy Logo T-Shirt - White XXXL Reedy Logo T-Shirt - Black M Reedy Logo T-Shirt - Black L Reedy Logo T-Shirt - Black XL Reedy Logo T-Shirt - Black XXL Reedy Logo T-Shirt - Black XXXL Factory Team /0 Motor Storage Bag Factory Team /0 Car Carrier Bag :: LRP Brushless Motors LRP504 LRP505 LRP50 LRP507 LRP508 LRP5087 LRP509 LRP5070 LRP507 LRP507 LRP5083 LRP5084 LRP5085 LRP508 LRP X- 9.5 Turn LRP X- 8.5 Turn LRP X- 7.5 Turn LRP X-.5 Turn LRP X- 5.5 Turn LRP X- 5.0 Turn LRP X- 4.5 Turn LRP X- 4.0 Turn LRP X- 3.5 Turn LRP X- 3.0 Turn Vector X- Stock-Spec 0.5 Turn Vector X- Stock Spec 3.5 Turn Vector X- Stock Spec 7.5 Turn Vector X- Stock Spec.5 Turn
3 :: LRP Speed Controls LRP830 LRP835 LRP8337 LRP8000 LRP8050 LRP80400 LRP80800 LRP80830 LRP80900 LRP8090 LRP80950 LRP8500 LRP80905 LRP80955 LRP8040 :: LRP Brushless Combos LRP8040 LRP804 LRP804 LRP8043 LRP8044 LRP8045 LRP804 LRP8047 LRP8048 LRP8049 LRP8054 LRP8055 LRP805 LRP8057 LRP8058 LRP8059 LRP8073 LRP8074 LRP8075 AI Super Reverse AI Pro Reverse AI Bullet Reverse AI Brushless Reverse AI Brushless Pro Reverse SPX Brushless Super Reverse V 8. Quantum Competition 3 SXX Competition Speed Control SXX Stock-Spec Speed Control SXX TC-Spec Speed Control NEXXT 4X esc SXX Competition V. SXX TC-Spec V. Ultimo Drift SXX TC / X- 3.0 Turn SXX TC / X- 3.5 Turn SXX TC / X- 4.0 Turn SXX TC / X- 4.5 Turn SXX TC / X- 5.0 Turn SXX TC / X- 5.5 Turn SXX TC / X-.5 Turn SXX TC / X- 7.5 Turn SXX TC / X- 8.5 Turn SXX TC / X- 9.5 Turn SXX COMP / X- 5.0 Turn SXX COMP / X- 5.5 Turn SXX COMP / X-.5 Turn SXX COMP / X- 7.5 Turn SXX COMP / X- 8.5 Turn SXX COMP / X- 9.5 Turn SXX Stock-Spec / X- Stock-Spec 0.5 Turn SXX Stock-Spec / X- Stock-Spec 3.5 Turn SXX Stock-Spec / X- Stock-Spec 7.5 Turn :: Apparel SP35** SP3** SP58** SP59** SP0** SP** SP** SP3** SP4** SP5** SP00 SP0 SP0 SP03 SP40** SP45 SP4 SP47 SP48 SP40** 75 084 :: /8 Kits and RTR s 000 00 003 005 00 00 05 08 00 030 Reedy 09 White T-Shirt (M, L, XL, XXL, XXXL) Reedy 09 Black T-Shirt (M, L, XL, XXL, XXXL) AE Logo Black T-Shirt (M, L, XL, XXL) AE Logo Blue T-Shirt (M, L, XL, XXL) AE Hooded Sweatshirt (S, M, L, XL, XXL) AE Vertigo Hooded Sweatshirt (S, M, L, XL, XXL) AE Vertigo Long Sleeve T-Shirt (S, M, L, XL, XXL) AE Vertigo White T-Shirt (S, M, L, XL, XXL) AE Vertigo Blue T-Shirt (S, M, L, XL, XXL) AE Vertigo Black T-Shirt (S, M, L, XL, XXL) /8 Inner and Outer Boxes Only, Set /8 Inner Boxes Only, Set /0 Inner and Outer Boxes Only, Set /0 Inner Boxes Only, Set AE Hats Black (S-M, L-XL, XXL-XXXL) /8 Car Carrier Bag Only /0 Car Carrier Bag Only /0 FT Motor Bag /0 FT Car Carrier Bag with Boxes, Set AE Pit Gloves (M, L, XL) Reedy 009 Track Banner Team Associated Track Banner ** Use part number plus the desired size when ordering RC8T RTR (ready-to-run) RC8T.4ghz RTR (ready-to-run) RC8B - RC8T Team Kit RC8B RTR (ready-to-run) RC8B.4ghz RTR (ready-to-run) RC8MT RTR (ready-to-run) RC8R Kamino RTR (ready-to-run) RC8R Niteline RTR (ready-to-run) SC8 RTR (ready-to-run) RC8LM RTR (ready-to-run) :: LRP Charger, Power Supply, Balancer, Iron LRP48 LRP4555 LRP4350 LRP4500 LRP5800 LRP580 LRP5803 LRP5804 :: LRP Misc. LRP500 LRP50 LRP50 LRP503 LRP504 LRP505 LRP50 LRP503 LRP5033 LRP5034 LRP8035 LRP850 LRP85 LRP89307 LRP8930 LRP8935 LRP8930 Quadra Pro Charger Pulsar Touch Competition Charger Power Supply Competition LiPo Parallel Balancer High Power Solder Station Soldering Tip 5mm Soldering Tip.mm Soldering Handle X- Replacement Ball Bearings X- Optional Ceramic Ball Bearings X- Small parts Set X- PreciSensor Unit X- Replacement alum Front can X- Lightweight Alum Can X- Alum Rear Cover X-.0mm sintered rotor X-.5mm sintered rotor X- 3.0mm sintered rotor BEC stabilizing capacitor Brushless/Brushed Cooling Set Brushless Low Profile Fan 70mm High Flex Sensor Wire 00mm High Flex Sensor Wire 50mm High Flex Sensor Wire 00mm High Flex Sensor Wire :: /, /0 Kits and RTR s 033 04 409 700 703 707 709 7030 703 7034 703 7037 7040 704 7043 7044 7080 709 800 80 9034 903 9038 9039 90 055 3005 300 30 FT Nitro TC3 Kit Nitro TC3 RTR Plus (ready-to-run) FT R5. Kit RC0T4 Team Truck Kit RC0T4. FT Kit SC0 WD Short Course Race Truck Kit SC0 Associated/RC0.com Truck RTR (ready-to-run) SC0 KMC Wheels Race Truck RTR (ready-to-run) SC0 Ready Lift RTR (ready-to-run) SC0 FT Kit RC0T4. RTR.4GHz Brushed (ready-to-run) RC0T4. RTR.4GHz Brushless (ready-to-run) SC0 RTR,.4ghz Brushless Lucas Oil Body SC0 RTR,.4ghz Brushless Speed Tech/Bully Dog Body SC0 RTR,.4ghz Brushless Pro Comp Body SC0 RTR,.4ghz Brushless Rockstar / Makita Body FT GT Nitro Truck Kit GT RS Truck Nitro RTR (ready-to-run) FT RC0R5 Kit FT RC0R5-OVAL Kit RC0B4 Buggy Team Kit RC0B4. FT Kit RC0B4. RTR.4GHz Brushed (ready-to-run) RC0B4. RTR.4GHz Brushless (ready-to-run) FT B44. 4WD Buggy Kit MGT 3.0 Nitro Monster Truck RTR (ready-to-run) FT TC5R Rubber Tire Edition 4WD Touring Car Kit FT TC 4WD Touring Car Kit TC4 4WD Touring Car RTR (ready-to-run)
33 :: /8 Kits and RTR s 0503 0504 8090 80904 80905 809 8095 8090 809 809 8093 8094 8095 8093 Limited Edition MGT 4.0 Nitro RTR, w/flag body (ready-to-run) Limited Edition MGT 8.0 Nitro RTR, w/flag body (ready-to-run) FT RC8B Nitro Buggy Kit FT RC8Be Electric Buggy Kit RC8RS Race Spec Nitro Buggy RTR (ready-to-run) RC8T Championship Edition RC8T-RS Race Spec Nitro Truggy RTR (ready-to-run) SC8 Short Course Race Truck, Red Bull Nitro RTR (ready-to-run) SC8 Short Course Race Truck, Lucas Oil Nitro RTR (ready-to-run) SC8 Short Course Race Truck, KMC Wheels Nitro RTR (ready-to-run) SC8 Short Course Race Truck, Bully Dog Nitro RTR (ready-to-run) SC8 Short Course Race Truck, AE Team Nitro RTR (ready-to-run) SC8 Short Course Race Truck, Pro Comp Nitro RTR (ready-to-run) SC8e Short Course Race Truck Rockstar/Makita RTR (ready-to-run) :: Contact Information :: Tools 449 450 54 54 543 544 545 54 547 548 55 553 554 5 5 53 54 55 5 57 589 590 59 79 737 378 379 370 3987 49 95 7709 FT Turnbuckle Wrench Offroad Ride Height Gauge FT Ride Height Gauge FT Hex Driver Set, (7 pcs) FT.050 Silver Hex Driver FT / Black Hex Driver FT.5mm Purple Hex Driver FT 5/4 Blue Hex Driver FT 3/3 Gold Hex Driver FT.5mm Green Hex Driver FT 3mm Red Hex Driver FT Screwdriver Set FT Phillips Silver Screwdriver FT Silver Spring Hook Tool FT Nut Driver Set, ( pcs) FT 3/ Black Nut Driver FT /4 Red Nut Driver FT 5.5mm Red Nut Driver FT /3 Green Nut Driver FT 7.0mm Silver Nut Driver FT 8mm Gold Nut Driver FT 5/4 Blue Ball Hex Driver FT 3/3 Gold Ball Hex Driver FT Ball Hex Driver Set, (3 pcs) FT Camber + Track Width Tool FT Body Scissors Inch Nylon Wire Ties Inch Nylon Wire Ties 8 Inch Nylon Wire Ties FT Droop Gauge Shock Building Tool Molded Tools, Set 4 Inch Nylon Wire Ties Associated Electrics, Inc. 0 Commercentre Drive Lake Forest, CA 930-8853 USA http://www.teamassociated.com http://www.rc0.com http://twitter/team Associated http://bit.ly/aeonfacebook call: (949) 544-7500 fax: (949) 544-750 Check out the following web sites for all of our electric kits, current products, new releases, setup help, tips, and racing info www.teamassociated.com. - www.rc0.com
34 :: Notes
Setup Sheet Front Suspension Driver: B44. Standard Setup Track: Conditions: Rear Suspension Date: Event: Rev. Anti Roll Bar: 0.047 Black 0.055 Silver None A B Anti Roll Bar: 0.047 Black 0.055 Silver None Bumpsteer Washer: Camber: Toe: 0 0 - Camber: Toe: 3 Ride Height: - 0mm A B C D Ride Height: Steering Rack: I O mm Front Back Washers: Aluminum Hub Tower: A B Wheelbase: Long Medium Short I O Notes: Notes: Measure ride height on back corner of chassis Front Shocks Spring: Silver Piston: # Rear Shocks Spring: Green Piston: # Shock Oil: 35 wt Limiter: Shock Oil: 30 wt Limiter: Electronics Motor & Wind: Radio: Pinion: Throttle / Brake e.p.a: Spur Gear: Throttle / Brake expo: Batteries: ESC: Throttle Profile: Battery Placement: Initial Brake: Drag Brake: Servo: Steering Expo: Differentials Other Front Diff Setting: Standard Body Type: JConcepts Punisher Rear Diff Setting: Standard Wing Type:.5 high Wing Angle: 9 Front Tires Rear Tires Tire: Holeshot.0 Tire: Holeshot.0 Compound: M3 Compound: M3 Insert: Standard Insert: Standard Wheel: Standard Wheel: Standard Race and Vehicle Comments Track Info Qualify: Main: Finish: TQ: Smooth: Bumpy: Blue Groove: Comments: Traction: High: Medium: Low: Soft Dirt: Grass: Clay: Wet: Dusty: Other: :: For more setups, visit RC0.com and click on Setup Sheets
3 :: Hardware - : Scale View Cap Head (shcs) Flat Head (fhcs) Button Head () 4-40x5/ (93) (aluminum,445) (94) (aluminum,80) 4-40x5/ (773) (9) -5x/8 (945) -5x5/ (4334) 4-40x/4 (8) 4-40x7/ (7874) (aluminum, 7873) 4-40x7/ (975) (97) 4-40x/ (95) 4-40x7/8 (7738) 3xmm (55) (motor mounting screws) 4-40x5/8 (95) Shims and Washers Ballstud Washer (930) 4-40x7/ () 4-40x3/4 (743) Ball Bearings.030 Nylon Spacer (487) Nuts (lock/plain) Steering Bearing (974) Servo Mount Washer (7337) 4-40 Aluminum Locknut (4449) 3/x5/ (90) #4 Washer (93) 4-40 Plastic Nut (47) 3/x3/8 (3977) Input Shaft Shim - Black (39) 5-40 Nylon Locknut (9744) 3/x/ RS (7935) 3/ Axle Shim - Silver (738) Outdrive Shim (39) 8-3 LP Steel Locknut (953) 8-3 Steel Locknut (95) 3/8x5/8 RS (397) Ballstuds Clips E-clip (99) Top Hat Bushings Small Top Hat Bushing (3874) Large Top Hat Bushing (947) Silver.0 Short (7) Silver.30 Long (77) Black.30 Long (3983) Diff Balls 5/4 Diff Thrust Balls (574) 3/3 Carbide Diff Balls (58) Notes:
Setup Sheet Front Suspension Anti Roll Bar: 0.047 Black 0.055 Silver None Bumpsteer Washer: Camber: Toe: Ride Height: Steering Rack: Notes: I O Front Back Front Shocks Spring: Shock Oil: Electronics Motor & Wind: Pinion: Spur Gear: Batteries: Battery Placement: B A B Washers: A Cam Holder Hex Spacing Driver: Track: Conditions: Piston: Limiter: Differentials Front Diff Setting: Rear Diff Setting: Front Tires Tire: Compound: Insert: Wheel: Race and Vehicle Comments Qualify: Main: Finish: TQ: Comments: Hex Spacing Camber - 0 + Rear Suspension Anti Roll Bar: Outer Ball & Shims Outer Ball & Shims º.5º º Toe 0 + - Toe 0 + 0.047 Black 0.055 Silver None Camber: Toe: Ride Height: Aluminum Hub Tower: A B Wheelbase: Long Medium Short Notes: Rear Shocks Spring: Shock Oil: Tire: Compound: Insert: Wheel: Track Info Arm Mount Shims - Bumpsteer I O Radio: Throttle / Brake e.p.a: Throttle / Brake expo: ESC: Initial Brake: Servo: Other Body Type: Wing Type: Rear Tires mm mm Date: Event: Wheel Base Shims Smooth: Bumpy: Blue Groove: Traction: High: Medium: Low: Soft Dirt: Grass: Clay: Wet: Dusty: Other: Wheelbase Wheelbase A B C D Piston: Limiter: Throttle Profile: Drag Brake: Steering Expo: Wing Angle: Rev. :: For more setups, visit RC0.com and click on Setup Sheets
Associated Electrics, Inc. 0 Commercentre Dr. Lake Forest, CA 930 USA http://www.teamassociated.com http://www.rc0.com http://twitter/team_associated http://bit.ly/aeonfacebook call: (949) 544-7500 - fax: (949) 544-750 Check out the following web sites for all of our kits, current products, new releases, setup help, tips, and racing info www.teamassociated.com. - www.rc0.com