Mtrized Pulley 165E, Ø 165 mm Mtrized Pulley 165E, with machined helical gear b, perfrms an efficiency, in a cmpact diameter f 165 mm nly. With a min RL f 400 mm and and pwers ranging frm 0.11kW t 1.5kW this size f mtrized pulley is suitable fr mst duties requiring such a small diameter e.g.: Light agriculture and bulk slids handling cnveyrs Mbile r prtable cnveyrs As a drive unit fr brush cleaners etc. Mtrized pulley 165E has standard IP66/67 enclsure and is available in cmplete stainless steel eecutin fr wash dwn applicatin. Fr the chice f the Mtrized Pulley it is very imprtant t knw r t calculate the belt tensin T1+T2 (radial lad). This MUST NOT OVERCOME the "ma. radial lad" allwed as shwn in the catalgue. Be careful t very high belt tensins when using thick, heavy and/r large belts. If the type 165E cannt prvide the necessary ma. radial lad T1+T2, yu have t chse a Mtrized Pulley with a bigger diameter. STANDARD SPECIFICATION f mtrized pulley Crwned mild steel shell, utside diameter 165mm. Mild steel shafts. Shell and shafts treated with anti-rust wa. Die cast aluminium bearing huses. Gearb frm die cast aluminium 2- and 3-stages. Sealing system-degree f prtectin IP66/67 (EN60034-5). Die cast aluminium terminal b with WAGO clamp. Vltage: mst cmmn glbally used vltages available. Please specify! 3-phase inductin mtr with ne rated vltage either lw r high vltage Available in bth 50Hz r 60Hz. Star cnnectin (Delta cnnectin n request). Mtr windings with insulatin class F (insulatin class H n request). Dynamical balanced rtr. Tw il plugs (ne with magnet). Minimum rller length (RL) 400mm (0.37kW: min RL 350mm. Ma. RL 1800mm (lnger RL n request). Standard mineral il ISOVG150 (synthetic il ISOVG220 n request). Oil change recmmended every 20.000 peratinal hurs. Single phase AC mtrs available in 0.37kW and 1.10kW, supplied with all necessary run and start capacitrs (if needed) tgether with current depending relay. Withut start capacitr the starting trque is 70% f the nminal trque nly Fr hrizntal installatin (angled and vertical installatin n request) STAINLESS SREEL eecutin TS 7N Crwned stainless steel shell (AISI304), utside diameter 165 mm. Stainless steel shafts (AISI303/304). Stainless steel cvered - ASI 303 - aluminium bearing husing Re-greasable labyrinth seals (AISI304). FDA & USDA fd grade grease Optin: FDA & USDA fd grade recgnized il. Fully stainless steel (AISI304) terminal b. Fully stainless steel (AISI304) straight cnnectr. Tw stainless steel il plugs (ne with magnet). TS7N - slid husing As with TS7N but with massive stainless steel bearing husing. TS8N As TS7N but with nn-re-greasable labyrinth seals. When rdering, please specify the required vltage, electrical cnnectin and eventual TS-number, ptins, brackets and idler pulleys. Envirnmental cnsideratin: page 77 Technical precautins: page 81-92, Optinal etras: page 15 and back cver, Cnnectin diagram: page 98-99, 14
OPTIONAL EXTRAS Mtrized Pulley 165E Specificatin Ttal stainless steel ptin AISI 304 range Re-greasable labyrinth seals! Fd grade il & grease - FDA & USDA recgnized - available n request Dust eplsin prf Mtrized Pulleys - ATEX 95 - Zne 22 - fr applicatins handling f dusty grain etc. On accrding t Eurpean Directive 94/9/EC. request! Black rubber lagging - STANDARD specificatins: - Smth lagging - Hardness 60 ±5 Shre A - Diamnd lagging - Hardness 60 ±5 Shre A White smth rubber lagging (FDA). Oil, fat & grease resistant Single phase mtrs available n request Electrmagnetic brake (fr 5.5 kw nt available) Min. RL dimensins by (mm) 50 Mechanical backstp Mdified fr vertical munting Mdified fr munting between 5-90 - e.g. fr magnetic separatrs Insulatin class F - Allwable ambient temperature: -25 C/+40 C Insulatin class H with synthetic il - Allwable ambient temperature: -25 C/+40 C SPECIAL mtrs fr applicatins with NO belt cntact Lw nise drives fr nise sensitive areas Parallel shell Thermal prtectr IP66/67 Cmpact stainless steel - AISI 304 r 316 range - terminal b Straight r elbw cnnectr with flying lead Straight cnnectr with flying lead - Stainless steel - AISI 304 range - Shaft sealing system - degree f prtectin IP66/67 (EN60034-5) Screened cables - a MUST tgether with Frequency Cnverters Eur wide range vltage (3220-240V / 380-415V 50 Hz) with +/-10% tlerance - DIN IEC 38 r (3380-400V / 660-690V 50 Hz) Special vltages - 50 and/r 60 Hz Please specify! CSA apprved mtrs - available n request nly! X = Optinal etras = Available as ptin with certain limitatins. Please refer t Technical precautins pages 81-92! = Fitted as standard 165E 15
Mtrized Pulley 165E, Ø 165 mm Mtrized pulley with Terminal b Straight cnnectr Elbw cnnectr Frnt shaft with cable slt Idler pulley SS versin Standard measurements A B C D E F G H K W L M N N1 U V R S T Type / Optin Ref. mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm 165E (UT165E) / Terminal b 165 163.5 43.5 40 80 30 10 21.5 41.5 48 41 24 95 14 SS versin (regreasable seals) 64.5 13.5 21.5 4 27 Straight cnnectr 21.5 43.5 4 27 Elbw cnnectr 21.5 43.5 20 48 12 Frnt shaft with cable slt 43.5 8-11 Munting brackets KL40 Mtrized Material Dimensins Weight Pulley D F I K S T V W1 X X1 Z Z1 Type mm mm mm mm mm mm mm mm mm mm mm mm kg 165E Steel 40 30 84 62 14 20 22 40 110 190 50 83 2.1 16
Mtrized pulley 165E Ø 165 mm 50 Hz Mtr Nminal belt Trque Belt Ma. Weight in kg fr STANDARD width Type Pwer N. Gear speed at Pull Radial f f stages Full Lad Lad Dimensin RL in mm Bracket Ples 50Hz T1+T2 per 50 mm kw/hp m/sec Nm N N 350 400 450 500 550 600 650 700 750 800 850 900 950 1000 1050 1100 up t 1800 0.05 170 2070 0.11/ 12 3 0.06 141 1700 9330 29 30.5 32 33 34 35 36.5 38 39 40 41.5 43 44 46 47 0.15 0.08 113 1375 0.10 86 1045 6 3 0.13 239 2905 0.16 193 2345 9330 30 31.5 33 34 35 36 37.5 39 40 41 42.5 44 45 47 48 0.20 157 1910 3 0.25 127 1545 0.37 0.32 97 1175 0.50 4 0.40 77 930 9330 26 28 29.5 31 32 33 34 35.5 37 38 39 40.5 42 43 45 46 0.50 60 735 2 0.63 49 595 0.80 38 455 1.00 29 360 6 3 0.16 341 4140 9330 33 34.5 36 37 38 39 40.5 42 43 44 45.5 47 48 50 51 0.20 302 3665 3 0.25 248 3005 0.32 189 2295 0.75/ 4 0.40 162 1815 9330 31 32.5 34 35 36 37 38.5 40 41 42 43.5 45 46 48 49 1.00 0.50 119 1435 2 0.63 96 1160 0.80 72 885 1.00 57 700 Available 4 3 0.25 332 4030 n KL40 9330 34 35.5 37 38 39 40 41.5 43 44 45 46.5 48 49 51 52 0.32 272 3305 request 0.40 226 2745 3 0.50 183 2220 0.63 139 1690 9330 1.10/ 2 0.80 110 1340 33 34.5 36 37 38 39 40.5 42 43 44 45.5 47 48 50 51 1.50 1.00 87 1060 1.25 70 855 2 1.60 54 650 8700 2.00 42 515 2.50 34 420 6950 0.50 237 2880 3 0.63 195 2360 9330 0.80 154 1870 1.50/ 1.00 122 1480 2.00 2 1.25 98 1195 34 35.5 37 38 39 40 41.5 43 44 45 46.5 48 49 51 52 8700 1.60 75 910 2 2.00 59 720 2.50 48 585 6950 3.15 39 485 Mtr Ma. Weight in kg fr STANDARD width Type Radial f Lad Dimensin RL in mm Bracket T1+T2 per 50 mm N 350 400 450 500 550 600 650 700 750 800 850 900 950 1000 1050 1100 up t 1800 Idler Pulley UT165E 9330 12.5 14.0 15.5 17.0 18.5 20.0 21.5 23.0 24.5 26.0 27.5 29.0 30.5 32.0 33.5 35.0 Available KL40 n request 17
Mtrized Pulley 165E Spare Parts List and sectinal drawings Ps. Descriptin Ps. Descriptin Ps. Descriptin 1 Frnt shaft 3 Rear flange 5 Bearing husing cmplete with geared rim 7 Bearing husing cmplete 8 Gearb 10 Terminal b bttm part 11 Terminal b cver 12 Shell 16 Rear shaft 19 Input wheel 20 Output pinin 22 Geared rim 23 Intermediate pinin shaft 24 Intermediate wheel 31 Labyrinth seal cver 53 Cable seal nipple (cable ptin) 53.1 Nipple (terminal b) 55 Spacer bushing 56 Spacer bushing 63 Ball bearing 64 Needle bearing 65 70 Ball bearing 73 Lcking ring 74 Lcking ring 81 Lcking ring 84 Lcking ring 85 Lcking ring 86 Lcking ring 93 Elbw r straight cnnectr 102 Screw 103 Screw 110 Screw 111 Screw 112 Scket set screw 113 Screw 114 Scket set screw 115 Oil plug with magnet 126 Key 127 Key 131 Key 132 Key 136 O-ring/Rubber seal 138 Rubber seal 139 Grease nipple 165E standard ptin: 2 stage gearb with terminal b 18
Mtrized Pulley 165E Spare Parts List and sectinal drawings Ps. Descriptin Ps. Descriptin 140 Deflectin seal 141 Duble lip seal 142 Duble lip seal 143 O-ring 145 Distance washer 146 Washer 148 Washer 150 Electrmagnetic brake 150.1 Frictin disc 156 Rectifier (nt shwn) 160 Oil plug 161 O-ring 163 O-ring 167 Screw 200 Rubber seal 204 Rtr cmplete with pinin 206 Insulated sleeve fr wire prtectin 208 Bearing husing with labyrinth grve 210 Fiing guard 225 Cable 226 Statr cmplete 229 WAGO clamp terminals 230 Fiing blts 240 Distance ring SS il plug Cable versin with elbw cnnectr Cable versin with straight cnnectr Stainlees steel versin TS7N Cable ptin with straight cnnectr 3-stage gearb Electrmagnetic brake 19