allast Compact SE Overview CompactSE- 03.08.04 or designs requiring the energy savings and aesthetic appeal of dimmed T4 compact fluorescent or T5 twin-tube lamps, Compact SE dimming ballasts are your solution. The Compact SE product family includes ballasts for nearly every type of dimmable compact fluorescent lamp. eatures Continuous, flicker-free dimming from 00% to 5% Standard 3-wire line-voltage phase-control technology for consistent fixture-to-fixture dimming performance Models for 4-pin T4 compact lamps and T5 twin-tube lamps Programmed rapid start design will preheat lamp cathodes before applying full arc voltage Lamps turn on to any dimmed level without flashing to full brightness Low harmonic distortion throughout the entire dimming range maintains power quality requency of operation ensures that ballast does not interfere with infrared devices operating between 38 and 4 khz Inrush current limiting circuitry eliminate circuit breaker tripping, switch arcing, and relay failure End-of-lamp-life protection circuitry ensures safe operation throughout entire lamp life cycle Ultra quiet operation Protected from miswires of any input power to control lead, or lamp leads to each other or ground 00% compatible with all Lutron 3-wire fluorescent controls 00% performance tested at factory Designed and assembled in the US 5-year limited warranty with Lutron field service commissioning (3-year standard warranty) from date of purchase allasts that dim T4 compact fluorescent lamps are intended for factory installation by OEM fixture manufacturer. Compact SE, case type 3.00 w (76mm) x.00 h (5mm) x 4.90 l (4mm) Compact SE, case type 3.00 w (76mm) x.00 h (5mm) x 6.75 l (7mm) Compact SE, case type.38 w (60mm) x.50 h (38mm) x 9.50 l (4mm) SPECIICTION SUMITTL
allast Specifications CompactSE- 03.08.04 Performance Dimming ange: 00% to 5% measured relative light output (LO) Lamp Starting: programmed rapid start Minimum Lamp Starting Temperature: 0 C (50 ) mbient Temperature Operating ange: 0 C (50 ) to 60 C (40 ) elative Humidity: maximum 90% noncondensing Operating Voltage: 0V or 77V at 60Hz Lamp Current Crest actor: less than.7 Lamp licker: none visible Light Output: constant ±% light output for line voltage variations of ±0% Lamp Life: average lamp life meets or exceeds rating of lamp manufacturer allast actor: greater than.95 for T4 quad or triple tube lamps, and greater than.85 for T5 twin-tube lamps Power actor: greater than.95 Total Harmonic Distortion (THD): less than 0% Maximum Inrush Current: 7 amps per ballast at 0V, 3 amps per ballast at 77V Sound ating: Inaudible in a 7da ambient Maximum allast Case Temperature: 75 C (67 ) Standards UL Listed (evaluated to the requirements of UL935) CS certified (evaluated to the requirements of C. No. 74) Class P thermally protected Meets NSI C8. High requency allast Standard Meets CC Part 8 Non-Consumer for EMI/I emissions requirements T4 compact fluorescent ballasts are MIL Std. 46E compliant (meets the requirements of CE0, E0 and E0) Meets NSI C6.4 Category surge protection standards to 6kV Manufacturing facilities employ ESD reduction practices that comply with the requirements of NSI/ESD S0.0 Lutron Quality Systems registered to ISO 900 SPECIICTION SUMITTL
allast Compact SE allast Models CompactSE-3 03.08.04 0 VOLTS 77 VOLTS Lamp Type Lamp Watts Lamps per ballast Case Type allast Current (amps) Compact SE Model Number allast Current (amps) Compact SE Model Number T4 4-Pin Quad-Tube 8W.0.4 D-T48-0--S D-T48-0--S.08.7 D-T48-77--S D-T48-77--S / diameter 6W.6.50 D-T46-0--S D-T46-0--S.. D-T46-77--S D-T46-77--S T4 4-Pin Triple-Tube 8W.0.4 D-T48-0--S D-T48-0--S.08.7 D-T48-77--S D-T48-77--S / diameter 6W 3W.6.50.3.59 D-T46-0--S D-T46-0--S D-T43-0--S D-T43-0--S...3.4 D-T46-77--S D-T46-77--S D-T43-77--S D-T43-77--S 4W.36.67 D-T44-0--S D-T44-0--S.6.9 D-T44-77--S D-T44-77--S T5 Twin-Tube 36/39W (6 ) 3.33.58.85 D-643-0- D-643-0- D-643-0-3.4.5.35 D-643-77- D-643-77- D-643-77-3 5/8 diameter 40W ( ) 3.33.6.88 D-7-0- D-7-0- D-7-0-3.4.5.38 D-7-77- D-7-77- D-7-77-3 50W ( ).38.69 D-43-0- D-43-0-.7.3 D-43-77- D-43-77- Mounting studs standard for T4 ballasts. Delete suffix -S in the model number if mounting studs not needed. SPECIICTION SUMITTL
allast Case Dimensions CompactSE-4 03.08.04 8-3 Threaded Stud 0.9 (.736mm) 4.0 (07 mm).00 (5 mm) C 3.00 (76 mm) G D 4.90 (4 mm) E 4.60 (7 mm) C (mounting centers) I.00 (5 mm) G.08 (7 mm) H H.60 (4 mm) I.39 (35 mm) E D H G I 8-3 Threaded Stud 0.9 (.736mm) C 6.00.00 (5 mm) (5 mm) C 3.00 (76 mm) D 6.75 (7 mm) E 6.50 (65 mm) (mounting centers) G.00.00 (5 mm) (9 mm) H.60 (4 mm) I.39 (35 mm) E D 8.30 ( mm) Power and control.50 (38 mm) wires are 8 (0.45m) C.38 (60 mm) D 9.50 (4 mm) E 8.9 (6 mm) (slot mounting centers) If using four hole mount, mounting centers are 9. C E (34 mm) x.70 (43 mm). D Lamp wires are 36 (0.90m) Mounting studs standard. When ordering, delete suffix -S in the ballast model number if mounting studs not needed. SPECIICTION SUMITTL
allast Wiring Diagrams CompactSE-5 03.08.04 One compact fluorescent lamp lack (Switched Hot) Compact SE lue 4-pin Lamp Holder Ground lue Two compact fluorescent lamps lack (Switched Hot) Compact SE 4-pin Lamp Holder Ground lue 4-pin Lamp Holder lue Dimming control wire colors do not necessarily match ballast wire colors (e.g. control dimmed hot may be yellow and ballast dimmed hot may be orange). Wire colors shown are for Lutron controls and ballasts only. allast and lighting fixture must be effectively grounded. Note: or T4 compact lamps, maximum lamp-to-ballast wire length is 3 feet (m). SPECIICTION SUMITTL
allast Compact SE Wiring Diagrams CompactSE-6 03.08.04 One T5 twin-tube lamp To Dimming Control lack (Switched Hot) Compact SE Dimming allast lue lue luorescent Lamp Ground Two T5 twin-tube lamps To Dimming Control lack (Switched Hot) Compact SE Dimming allast Ground lue lue luorescent Lamp luorescent Lamp Three T5 twin-tube lamps To Dimming Control lack (Switched Hot) Compact SE Dimming allast lue/white lue/white luorescent Lamp luorescent Lamp Ground lue lue luorescent Lamp Dimming control wire colors do not necessarily match ballast wire colors (e.g. control dimmed hot may be yellow, and ballast dimmed hot may be orange). Wire colors shown are for Lutron ballasts and controls only. allast and lighting fixture must be effectively grounded. Note: or T5 twin-tube lamps, maximum lamp-to-ballast wire length is 3 feet (m). SPECIICTION SUMITTL
allast CompactSE-7 03.08.04 TTENTION ELECTICINS ND CONTCTOS allast/socket Leads Lead lengths from ballast to socket must not exceed 3 (m) for T4 and T5 twin-tube lamps. Lamp Sockets Quality lamp sockets are required to ensure positive lamp-pin to socket contact. T4 compact sockets must be the 4 pin type, and must be used with 4 pin compact lamps. T5 twin-tube lamps require sockets that lock into the lamp base and provide proper lamp support to hold lamp pins in full contact with socket. Lamp Mounting for T5 Twin-Tube Many fluorescent lamp sockets are available with mounting slots to vary the height of the lamp away from the grounded metal surface. Use these slots to keep the outside edge of the lamp at least /4" away from the grounded metal surface. Having a fluorescent lamp too close to the grounded metal will make the minimum intensity too low and will reduce lamp life. Wiring and Grounding ll wiring from the dimming control to Compact SE ballasts is line voltage wiring and may be run together in the same conduit. allast and lighting fixture must be effectively grounded. allasts must be installed per national and local electrical codes. Number of allasts Per Control To calculate the maximum number of ballasts allowed per control, divide control s current capacity by individual ballast current. Certain controls allow a specific maximum number of ballasts. allast Operating Temperature allast case temperature must not exceed 75 C at any point on ballast. PEOMNCE TTENTION CILITIES MNGES Lamps Must e Seasoned New fluorescent lamps must be operated for 00 hours at full output ( seasoned ) to render lamp impurities inert, so as to achieve proper dimming performance and average rated lamp life. SEVICE eplacement Parts Use replacement parts with exact Lutron model numbers. Consult Lutron if you have any questions. urther Information allasts for other lamp types and voltages are available. Consult Lutron s luorescent Dimming Systems Selection Guide (P/N 366-00). or further information, please visit us at http://www.lutron.com/ballasts or contact our 4-hour Technical Support Center at -800-53-9466. SPECIICTION SUMITTL