LED microwave sensor T8 tube light

Transcription

1 LED microwave sensor T8 tube light Product Feature Microwave sensor LED T8 offers a driver and radar sensor intergrated technology. The new technology helps the LED tube save more energy. LED tube will dimmed to 30% of the original power in a certain time after the object left the detective area. Advantages 1. Microwave sensor LED tube is designed for car park, warehouse and other special area, which can be dimmable intelligently according to the man or car. 2. Enters in or out to save more energy for you. 3. It can save 90% energy by sanding Radar Sensor LED tube. 4. Inner power efficiency more than 87%. 5. High quality, high lumen, good heat dissipation.

2 6. Detective distance: 5~10m. 7. Delay time (30~120s) can be customized. 8. When the car or man enters into the area, LED tube will be full brightness, then keep working for 35seconds after the man or car is away from the area, finally become 3watt in standby model. 9. No RF interference, No flickering or buzzing. 10. Comply with ETL SAA TUV and CE Standards. 11. Constant current driver with heat protection system, can work under unstable voltage 12. Isolated EMC driver supply, with overvoltage protection and overcurrent protection ,000 hours lifetime with stable quality and 3 years warranty. 14. Sensing distance, time, sensitivity can be set according to your requirements. 15. Instant start, no warm up time required, no noise, no flickering, protect your eyes. 16. No need for starter and ballasts. 17. Anti-shock, anti-hit; No danger of broken glass. 18. No mercury or other hazardous materials. 19. Clear/Striped/Frosted cover available. 20. Good commonality. It can replace of the conventional fluorescents. Technical specification 2ft/ 0.6m LED 3ft/ 0.9m LED 4ft/ 1.2m LED 5ft/ 1.5m LED Product Model 8w/10w 13w 20w 23w Dimesion 594/ 602mm 908mm 1212mm 1513mm Luminous (Frosted lens) 900lm±10% 1200lm±11% 1800lm±12% 2100lm±13% Luminous (Clear lens) 1000lm±10% 1300lm±11% 2000lm±12% 2300lm±13% Color Temperture 3000K/ 4000K/ 5000K/ 5700K/ 6500K CRI 72~75, or Ra80, or Ra90 Input Voltage AC100~240V, 50/60HZ AC100~277V, 50/60HZ Power Factor 0.90~0.95 Efficiency >0.86 Beam Angle >120

3 Light-emitting surface 180 Warranty 2 years Operation Temperature -20ºC to 40ºC Storage Temperature -40ºC to 85ºC Installation Lamp bracket of inductive ballast: 1) Turn off the power to the light fixture at the breaker panel before installation. 2) Open the diffuser from the light fixture. 3) Remove the fluorescent tubes. Please dispose of these items properly as they contain mercury. 4) Open the wiring cover to expose the fluorescent ballast. 5) Cut the wire as shown. Do not remove the starter and ballast, Keep it in place.

4 6) Make the new wire connect to branch circuit shown as the diagram below. Connect the L/N to one end of lampholder, the other end of the lamp access to the other end of the lampholder. After modified, add an identification for the live end of lampholder, e.g. LIVE END or L, N. 7) Replace the cover over the wiring channel. 8) IMPORTANT: Install the label provided that states "this fixture has been modified for LED lamps", inside the fixture in an easily visible location to anyone changing lamps, possibly on the cover over the wiring channel. Lamp bracket of electronic ballast: 1) Turn off the power to the light fixture at the breaker panel before installation. 2) Open the diffuser from the light fixture. 3) Remove the fluorescent tubes. Please dispose of these items properly as they contain mercury.

5 4) Open the wiring cover to expose the electronic ballast. 5) Cut the wire as shown. Do not remove the ballast, Keep it in place. 6) Make the new wire connect to branch circuit shown as the diagram below. Connect the L/N to one end of lampholder, the other end of the lamp access to the other end of the lampholder. After modified, add an identification for the live end of lampholder, e.g. LIVE END or L, N. 7) Replace the cover over the wiring channel. 8) IMPORTANT: Install the label provided that states "this fixture has been modified for LED lamps", inside the fixture in an easily visible location to anyone changing lamps, possibly on the cover over the wiring channel.

6 Application 1. Underground parkings lighting project. 2. Motel lighting project 3. Walking gallery of schools,hospitals,stations,buildings ect. 4. Warehouses need long time lighting but no need so bright lighting all the time. 5. Other public places that needs long time lighting but want to save more energy. Working Theory