Energy Solutions LED Accelerator Program

Transcription

1 Energy Solutions LED Accelerator Program Product Qualification Statement I hereby certify that the LED lighting product (Product) listed below meets all applicable general and specific criteria for qualification with the LED Accelerator Program (the Program) as summarized in Attachment A, Product Qualification Summary, and detailed in LEDA Product Qualification Requirements, ; Version 1.5 (October, 2013). I further certify that all information and documentation submitted for qualification of said Product is representative of the specific product model, and that any product sold or otherwise provided for use in LED lighting projects that receive incentives from the Program will meet or exceed the Program criteria. Brand Company Model Number Tier Qualification Signature Printed Name Company Date Title

2 Tier I Requirements Tier II Requirements LED Type Efficacy, Lumens /Watt Color Rendering Index Power Factor Maximum Total Harmonic Distortion, Current Warranty Life, Hours Efficacy, Lumens /Watt Color Rendering Index Power Factor Maximum Total Harmonic Distortion, Current Warranty Life, Hours MR Lamps % 5 years 35, % 5 years 35,000 PAR Lamps % 5 years 35, % 5 years 35,000 A19 Lamps % 5 years 35, % 5 years 35,000 Recessed Downlights % 5 years 50, % 5 years 50,000 Display Case % 5 years 50, % 5 years 50,000 Track Mono-Point % 5 years 50, % 5 years 50,000 1X4 Troffers % 5 years 50, % 5 years 50,000 2X2 Troffers % 5 years 50, % 5 years 50,000 2X4 Troffers % 5 years 50, % 5 years 50,000 Lowbays % 5 years 50, % 5 years 50,000 Highbays % 5 years 50, % 5 years 50,000 Highbay Aisle % 5 years 50, % 5 years 50,000 Linear Ambient: Direct % 5 years 50, % 5 years 50,000 Linear Ambient: Indirect % 5 years 50, % 5 years 50,000 Linear Ambient: I/D % 5 years 50, % 5 years 50,000 Linear Ambient: D/I % 5 years 50, % 5 years 50,000 Parking Garage % 5 years 50, % 5 years 50, If MR16s are low voltage or less than 5 watts, no power factor or THD requirement, consistent with ENERGY STAR. 2. THD current should be measured at full luminaire output across specified voltage range. THD lamp requirements in accordance with ANSI C At this time PG&E is not giving incentives or rebates for integrated LED tube lights in any of their programs, including LEDA. PG&E may allow LED tubes with separate drivers mid 2014 but until PG&E lists them in PG&E's Appendix F, Table of Pre-Qualified Integral LED Lamps & Qualification Process, we will not offer incentives on these products. 4. Exterior lighting retrofits are limited and must be implemented in conjunction with Tier 1 or Tier 2 interior retail lighting.

3 5. Retrofit kits are eligible and must meet the same performance requirements as similar non-retrofit kits listed above, e.g. a 2x4 LED troffer retrofit kit has the same performance requirements as the 2x4 troffer in the above table. Manufacturers must submit the same documents on the LEDA checklist ( for retrofit kits. LM79 and in-situ temperature tests must be performed in specified fixtures listed on the DLC retrofit kit webpage or a LM79 test and an in-situ temperature test can be conducted with the retrofit kit installed in the fixture that will be installed for the project. Retrofit kits must remove the existing ballast and tombstones and new source components be assembled in the housing.

4 ATTACHMENT A: PRODUCT QUALIFICATION SUMMARY General Product Criteria All LEDA Tiers 1. Allowable Lamp Bases Must be a lamp base listed by ANSI, if applicable 2. Color Maintenance The change of chromaticity over the minimum lumen maintenance test period (6000 hours) shall be within on the CIE 1976 (u,v ) diagram. 3. Color Spatial Uniformity The variation of chromaticity in different directions (i.e., with a change in viewing angle) shall be within from the weighted average point on the CIE 1976 (u,v ) diagram. 4. Color Rendering Index CRI (Ra) greater than 80. Also R9 value must be greater than Dimming Product packaging must clearly indicate whether the lamp is dimmable or not dimmable. Manufacturers qualifying dimmable products must maintain a Web page providing dimmer compatibility information. efficacy, light output, CCT, CRI and power factor of dimmable lamps will be confirmed with the lamp operated at full power. The luminaire and its components shall provide continuous dimming from 100% to 20% of total light output. Step dimming, if employed, shall provide at least two discrete light output levels 20% of total light output and not including 100% output. 6. Electromagnetic and Radio Frequency Interference Must meet FCC 47 CFR Part 15 (remote) or 18 (integral) emission limits 7. Incompatibility and Application Exceptions 8. Low-Voltage Compatibility Must clearly state any known incompatibility with photo controls, occupancy sensors, or timing devices. In addition, packaging should state specific application exceptions, such as totally enclosed fixtures, insulated air-tight (ICAT) recessed downlights, damp locations, and any other application restrictions. Products intended for use on low-voltage circuits must state compatibility with low-voltage transformers. 9. Maximum Off-State Power 0 W Exception - luminaires with integral occupancy, motion, photo-controls or individually addressable fixtures with external control: 0.5 W 10. Operating Temperature 11. Noise 12. Operating Voltage 13. Output Operating Frequency 14. Physical Size 15. Thermal Management -20 C Class A sound rating Must operate at rated nominal voltage of 120, 240 or 277 VAC, or at 12 or 24 VAC or VDC. 120 Hz Not to exceed target dimensions as per applicable ANSI specifications. Shall adhere to device manufacturer guidelines, certification programs, and test procedures for thermal management.

5 ATTACHMENT A: PRODUCT QUALIFICATION SUMMARY 16. Total Harmonic Distortion (amperage) < 20% for fixtures, <80% for Tier 1 MR and PAR lamps, <50% for Tier 2 MR and PAR lamps per ANSI C Transient Protection Must comply with IEEE C , Class A operation 18. Toxic Reduction Requirements Luminaires and lamps shall not exceed hazardous substance concentrations set for in the European Union s (EU) Restriction of the Use of Certain Hazardous Substances (RoHS) Directive, California consumers are not obligated to purchase any full fee service or other service not funded by this Program. This Program is funded by California utility ratepayers under the auspices of the California Public Utilities Commission (CPUC.) Los consumidores en California no están obligados a comprar servicios completos o adicionales que no esten cubiertos bajo este Programa. Este Programa está financiado por los usuarios de servicios públicos en California bajo la jurisdicción de la Comisión de Servicios Públicos de California (CPUC.) PG&E refers to Pacific Gas and Electric Company. A subsidiary of PG&E Corporation Pacific Gas and Electric Company. All rights reserved.