Energy Solutions LED Accelerator Program PRODUCT QUALIFICATION REQUIREMENTS

Transcription

1 Energy Solutions LED Accelerator Program PRODUCT QUALIFICATION REQUIREMENTS Version 1.5 October, 2013 Prepared for Pacific Gas and Electric Company San Francisco, California Prepared by Energy Solutions 1610 Harrison Street Oakland, California California consumers are not obligated to purchase any full fee service or other service not funded by this Program. This Program is funded by California utility ratepayers under the auspices of the California Public Utilities Commission (CPUC.) Los consumidores en California no están obligados a comprar servicios completos o adicionales que no esten cubiertos bajo este Programa. Este Programa está financiado por los usuarios de servicios públicos en California bajo la jurisdicción de la Comisión de Servicios Públicos de California (CPUC.) PG&E refers to Pacific Gas and Electric Company. A subsidiary of PG&E Corporation Pacific Gas and Electric Company. All rights reserved.

2 TABLE OF CONTENTS 1. SUMMARY PRODUCT REQUIREMENTS FOR ELIGIBLE MEASURES/ HARDWARE LEDA PRODUCT PERFORMANCE CRITERIA GENERAL PRODUCT CRITERIA PRODUCT SPECIFICATION BACKGROUND... 8 APPENDIX A: PRODUCT SUBMISSION REQUIREMENTS APPENDIX B: THEORETICAL LUMEN MAINTENANCE (LLD) FUNCTIONS APPENDIX C: PRODUCT SUBMISSION CHECKLIST

3 1. Summary 1.1 LED Accelerator Program The Energy Solutions LED Accelerator Program (LEDA) is a Third Party program funded through the Pacific Gas and Electric Company (PG&E) which serves large multisite commercial businesses receiving electric service from PG&E, with a particular emphasis on retail, grocery, restaurants and museums/art galleries. 1.2 Measures LEDA incents high performance light emitting diode (LED) retrofit installations for the following measures: MR Lamps PAR Lamps A-19 Lamps Downlights Display Case Lights Track Mono-Point 1X4 Troffers, including retrofit kits 2X2 Troffers, including retrofit kits 2X4 Troffers, including retrofit kits Linear Ambient Direct, including retrofit kits Linear Ambient Direct/Indirect, including retrofit kits Linear Ambient Indirect/Direct, including retrofit kits Linear Ambient Indirect, including retrofit kits Lowbays, including retrofit kits Highbays, including retrofit kits Highbay Aisle, including retrofit kits Parking Garage Controls * Exterior, parking garage and lighting control measures are only eligible if installed in conjunction with equal or more interior Tier 1 or Tier 2 lighting. If parking garage is enclosed and is affiliated with retail stores it is an eligible measure. 1.3 Incentive Calculations LEDA provides incentives for LED retrofits based on first-year kilowatt-hour (kwh) savings associated with the eligible retrofit measures. The kwh savings are calculated by taking the difference between wattages of the existing fixtures or lamps and their LED replacements. For retrofits of products that are not on during peak hours (connected load), incentives are provided at a reduced level based on off-peak demand reduction. 3

4 Table 1 LEDA Incentive Levels Note: Exterior lighting, multiple controls and Energy Star or DesignLights Consortium certified LEDS are limited and must be implemented in conjunction with interior retail lighting and Tier 1 and Tier 2 LED products with the majority of the retrofit utilizing Tier 1 and Tier 2 products. These products will be incentivized at the PG&E nonresidential calculated incentive currently at $0.08/kWh saved plus $100/kW saved. 2. Product Requirements for Eligible Measures/ Hardware 1. Products must meet or exceed ENERGY STAR standards when applicable, unless otherwise specified. 2. Products must meet or exceed standards established by PG&E and/ or the Design Lights Consortium if no Energy Star standard currently exists, unless otherwise specified. 3. All product specifications must be verified by an accredited lab from the following list of ENERGY STAR qualifying certified laboratories: 4. When submitting more than one version of a product, all versions must fall within ENERGY STAR product grouping allowances. 1 The representative model shall be the variation expected to have the greatest difficulty meeting the performance requirements outlined in this specification. 5. Product qualification in LEDA program is in no way a representation by LEDA or PG&E as to the economic or technical feasibility or performance, operational capability, or reliability of such products. 6. Mandatory LEDA program requirements are listed below; criteria are optional only when noted as Recommended. 1 US Department of Energy: Energy Star Program for Luminaires Partner Commitments Version V1.2 December 21,

5 3. Table 2 June 15, 2013 LEDA Product Performance Criteria Tier I Requirements Tier II Requirements LED Type Efficacy, Lumens /Watt Color Rendering Index Power Factor Maximum Total Harmonic Distortion, Current Warranty Life, Hours Efficacy, Lumens /Watt Color Rendering Index Power Factor Maximum Total Harmonic Distortion, Current Warranty Life, Hours MR Lamps % 5 years 35, % 5 years 35,000 PAR Lamps % 5 years 35, % 5 years 35,000 A19 Lamps % 5 years 35, % 5 years 35,000 Recessed Downlights % 5 years 50, % 5 years 50,000 Display Case % 5 years 50, % 5 years 50,000 Track Mono-Point % 5 years 50, % 5 years 50,000 1X4 Troffers % 5 years 50, % 5 years 50,000 2X2 Troffers % 5 years 50, % 5 years 50,000 2X4 Troffers % 5 years 50, % 5 years 50,000 Lowbays % 5 years 50, % 5 years 50,000 Highbays % 5 years 50, % 5 years 50,000 Highbay Aisle % 5 years 50, % 5 years 50,000 5

6 Linear Ambient: Direct % 5 years 50, % 5 years 50,000 Linear Ambient: Indirect % 5 years 50, % 5 years 50,000 Linear Ambient: I/D % 5 years 50, % 5 years 50,000 Linear Ambient: D/I % 5 years 50, % 5 years 50,000 Parking Garage % 5 years 50, % 5 years 50, If MR16s are low voltage or less than 5 watts, no power factor or THD requirement, consistent with ENERGY STAR. 2. THD current should be measured at full luminaire output across specified voltage range. THD lamp requirements in accordance with ANSI C At this time PG&E is not giving incentives or rebates for integrated LED tube lights in any of their programs, including LEDA. PG&E may allow LED tubes with separate drivers mid 2014 but until PG&E lists them in PG&E's Appendix F, Table of Pre-Qualified Integral LED Lamps & Qualification Process, we will not offer incentives on these products. 4. Exterior lighting retrofits are limited and must be implemented in conjunction with Tier 1 or Tier 2 interior retail lighting. 5. Retrofit kits are eligible and must meet the same performance requirements as similar non-retrofit kits listed above, e.g. a 2x4 LED troffer retrofit kit has the same performance requirements as the 2x4 troffer in the above table. Manufacturers must submit the same documents on the LEDA checklist ( for retrofit kits. LM79 and in-situ temperature tests must be performed in specified fixtures listed on the DLC retrofit kit webpage or a LM79 test and an in-situ temperature test can be conducted with the retrofit kit installed in the fixture that will be installed for the project. Retrofit kits must remove the existing ballast and tombstones and new source components be assembled in the housing. 6

7 4. Table 3 - General Product Criteria General Product Criteria All LEDA Tiers 1. Allowable Lamp Bases Must be a lamp base listed by ANSI, if applicable 2. Color Maintenance The change of chromaticity over the minimum lumen maintenance test period (6000 hours) shall be within on the CIE 1976 (u,v ) diagram. 3. Color Spatial Uniformity The variation of chromaticity in different directions (i.e., with a change in viewing angle) shall be within from the weighted average point on the CIE 1976 (u,v ) diagram. 4. Color Rendering Index CRI (Ra) greater than 80. Also R9 value must be greater than Dimming Product packaging must clearly indicate whether the lamp is dimmable or not dimmable. Manufacturers qualifying dimmable products must maintain a Web page providing dimmer compatibility information. efficacy, light output, CCT, CRI and power factor of dimmable lamps will be confirmed with the lamp operated at full power. The luminaire and its components shall provide continuous dimming from 100% to 20% of total light output. Step dimming, if employed, shall provide at least two discrete light output levels 20% of total light output and not including 100% output. 6. Electromagnetic and Radio Frequency Interference 7. Incompatibility and Application Exceptions Must meet FCC 47 CFR Part 15 (remote) or 18 (integral) emission limits Must clearly state any known incompatibility with photo controls, occupancy sensors, or timing devices. In addition, packaging should state specific application exceptions, such as totally enclosed fixtures, insulated air-tight (ICAT) recessed downlights, damp locations, and any other application restrictions. 8. Low-Voltage Compatibility Products intended for use on low-voltage circuits must state compatibility with low-voltage transformers. 9. Maximum Off-State Power 0 W Exception - luminaires with integral occupancy, motion, photo-controls or individually addressable fixtures with external control: 0.5 W 10. Operating Temperature -20 C 11. Noise Class A sound rating 12. Operating Voltage Must operate at rated nominal voltage of 120, 240 or 277 VAC, or at 12 or 24 VAC or VDC. 13. Output Operating Frequency 120 Hz 14. Physical Size Not to exceed target dimensions as per applicable ANSI specifications. 15. Thermal Management Shall adhere to device manufacturer guidelines, certification programs, and test procedures for thermal management. 16. Total Harmonic Distortion (amperage) < 20% for fixtures, <80% for Tier 1 MR and PAR lamps, <50% for Tier 2 MR and PAR lamps per ANSI C Transient Protection Must comply with IEEE C , Class A operation 18. Toxic Reduction Requirements Luminaires and lamps shall not exceed hazardous substance concentrations set for in the European Union s (EU) Restriction of the Use of Certain Hazardous Substances (RoHS) Directive,

8 5. Product Specification Background 5.1 Luminaire Efficacy Luminaire efficacy requirements are based on 2012/2013 Energy Star and DesignLights Consortium qualified products database. Tier 1 efficacy requirement was set at the 50 th percentile of Energy Star or DesignLights Consortium efficacy levels and Tier 2 was set at the 75 th percentile. The average trend line was projected to the end of 2014 and adjusted for rounding, quantity of products able to meet projected levels and easing of PAR and MR lamps to increase the uptake of the LED lamp market sector. 5.2 Potential Effective Useful Life Two methods are accepted for the calculation of L70 lifetime: calculations based component-level performance or calculations based on luminaire-level performance OPTION 1 Component performance: The following documentation must be provided: a) IES LM-80 test report for LED package, array, or module; minimally including light output measured every 1,000 hours and recorded for a minimum of 6,000 hours at 55 C, 85 C and a third temperature at the discretion of the manufacturer. b) In-Situ Temperature Measurement Test report indicating the temperature of both the highest temperature LED and the power supply at thermal equilibrium in accordance with ANSI/UL (hardwired) or ANSI/UL (corded). 2. OPTION 2 Luminaire performance: Provide IES LM- 79 test results for entire luminaire at 0 hours, and at 6000 hours after continuous operation in the appropriate UL1598/153 environment. For L70 classification, the following minimum average lumen maintenance values must be demonstrated: Table 4 - Lumen Maintenance Requirements Maximum L70 Life Claim (hours) lumen maintenance after test duration (% of initial lumens) 3 Total Test Duration (Hours) 35, % 35, % 35, % 2 US Department of Energy: Energy Star Program for Luminaires Partner Commitments Version V1.2 December 21, 2012, pages lumen maintenance for 6000 Hr and 8750 Hr test is based on ENERGY STAR Program Requirements Product Specification for Lamps (Light Bulbs) Eligibility Criteria Version 1.0, FINAL, page 15, August 28, 2013, ( pecification.pdf) 8

9 Lumen maintenance life projection claims in excess of 35,000 hours shall be substantiated with a TM-21 lumen maintenance life projection report. 5.3 Product Warranty Product warranties must guarantee proper operation for designated period of time under normal use, up to and including at least the actual hours of operation. A warranty must be provided for lamps or luminaires, covering material repair or replacement for a minimum of five (5) years from the date of purchase. The lumens over the five year warranty period must be maintained to 70% or higher than the initial lumens. 9

10 Appendix A: Product Submission Requirements 4 Product Cut Sheet 1. Product description, including model number, accessories, and intended applications 2. Electrical characteristics a. Maximum power usage of product (Watts) b. Chip current (milli-amperes; ma) c. Operating voltage range (Volts) d. Off-state power usage (Watts) e. Dimming capability 3. Optical characteristics a. Total luminous output of product (Lumens) b. Luminous efficacy (Lumens/ Watt) c. Color Rendering Index (CRI) d. Correlated Color Temperature (CCT) 4. Other characteristics a. Product rated life b. Product L70, if different than rated life c. Operating temperature range ( F or C) 5. Additional recommended information (as applicable) a. Physical dimensions of product, if non-standard b. Center beam candle power c. Optical beam angle d. Optical distribution type LM-79 Test Results 1. Electrical Data a. Input voltage (Volts) b. Current (Amperes) 4 For more information, contact Energy Solutions or see US Department of Energy: US Department of Energy: Energy Star Program for Lamps (Light Bulbs) Partner Commitments Version V1.0 August 28, c. Power (Watts) d. Power Factor e. Total Harmonic Distortion (amperage) 2. Light Output a. Total luminous output (Lumens) b. Luminous efficacy (Lm/W) 3. Light Distribution a. Zonal Lumen Summary, including optical distribution type and cutoff rating if applicable b. Candela Distribution c. Polar Graph d. Additional recommended information Spacing Criteria Coefficient of Utilization (CU) and Isoilluminance plot Glare Rating 4. Color characteristics a. Correlated Color Temperature (CCT) b. Color Rendering Index (CRI) c. Chromaticity Coordinates d. Additional recommended information Spectral Power Distribution (SPD) Product Lifetime Data 1. Lumen depreciation (L70) OPTION 1 Component performance a. IES LM-80 test report for LED package, array, or module; minimally including light output measured every 1,000 hours and recorded for a minimum of 6,000 hours at 55 C, 85 C and a third temperature at the discretion of the manufacturer. b. In-Situ Temperature Measurement Test report indicating the temperature of both the highest temperature LED and the power supply at thermal equilibrium in 10

11 accordance with ANSI/UL (hardwired) or ANSI/UL (corded). OPTION 2 Luminaire performance a. IES LM- 79 test results for entire luminaire at 0 hours, and at 6000 hours after continuous operation in the appropriate UL1598/153 environment 5.7 Warranty 1. Luminaire warranty, covering repair or replacement of defective electrical parts (including light source and power supplies) from the date of purchase. Must guarantee lumen maintenance remain at 70% or higher than the initial lumens during the warranty period. We encourage manufacturers to address color shift in the warranty. 2. Driver warranty from manufacturer indicating the maximum power supply case temperature for which warranty is offered is recommended 5.8 UL Listing 1. UL certification document 5.9 Total Harmonic Distortion- Amperage Measurement (THD-a) 1. THD-a laboratory test data from an Energy Star accredited laboratory. 2. Max THD result from the following calculation: Where: THD= Total Harmonic Distortion, and PF= Power Factor The Max THD formula was derived from a formula expressing the relationship between power factor and THD, expressed as: This relationship allows a worst case scenario or a Max THD to be calculated if the power factor is known for a given product Product Qualification Statement 1. Written statement verifying that the product meets all applicable general and specific criteria. 2. Written statement verifying that all included information and documentation is representative of the indicated product line. 11

12 Appendix B: Theoretical Lumen Maintenance (LLD) Functions Based on exponential decay California consumers are not obligated to purchase any full fee service or other service not funded by this Program. This Program is funded by California utility ratepayers under the auspices of the California Public Utilities Commission (CPUC.) Los consumidores en California no están obligados a comprar servicios completos o adicionales que no esten cubiertos bajo este Programa. Este Programa está financiado por los usuarios de servicios públicos en California bajo la jurisdicción de la Comisión de Servicios Públicos de California (CPUC.) PG&E refers to Pacific Gas and Electric Company. A subsidiary of PG&E Corporation Pacific Gas and Electric Company. All rights reserved.

13 California consumers are not obligated to purchase any full fee service or other service not funded by this Program. This Program is funded by California utility ratepayers under the auspices of the California Public Utilities Commission (CPUC.) Los consumidores en California no están obligados a comprar servicios completos o adicionales que no esten cubiertos bajo este Programa. Este Programa está financiado por los usuarios de servicios públicos en California bajo la jurisdicción de la Comisión de Servicios Públicos de California (CPUC.) PG&E refers to Pacific Gas and Electric Company. A subsidiary of PG&E Corporation Pacific Gas and Electric Company. All rights reserved.

14 Appendix C: Product Submission Checklist Item Included Check 1. Product Specification Sheet 2. LM-79 test results* 3. Product information OPTION 1: Component performance a. LM-80 test results* b. In-situ temperature measurement test results* (accredited lab) OR OPTION 2: Luminaire performance LM79 test results at 6,000 hrs or more a. Product warranty 4. UL certification document 5. Total Harmonic Distortion Amperage Measurement (THD-a)** 6. Proof of ENERGY STAR submittal or Intent to Submit to ENERGY STAR 7. LEDA Product Qualification Statement OR *Must come from an accredited lab from the following ENERGY STAR qualified list of certified laboratories: **THD requirement may be met by following the Max THD calculation method (see LEDA Product Qualification Requirements Appendix A 5.9(2)) or by submitting test data from an accredited lab. California consumers are not obligated to purchase any full fee service or other service not funded by this Program. This Program is funded by California utility ratepayers under the auspices of the California Public Utilities Commission (CPUC.) Los consumidores en California no están obligados a comprar servicios completos o adicionales que no esten cubiertos bajo este Programa. Este Programa está financiado por los usuarios de servicios públicos en California bajo la jurisdicción de la Comisión de Servicios Públicos de California (CPUC.) PG&E refers to Pacific Gas and Electric Company. A subsidiary of PG&E Corporation Pacific Gas and Electric Company. All rights reserved.