Update Alert: Firmware updates are posted to the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide Door lock and key interface compatible with the latest Kia vehicles. The available features include brake, hood, trunk and door trigger sensors. Index Vehicle Application Guide... 0 Installation Type 1: 009-011 Kia Borrego... Type : 010 Kia Optima and Magentis... Type 3: 011 Kia Sorento... Type : 011 Kia Sportage... 03 0 05 06 Programming Module Programming... Resetting the Module... LED Diagnostics... Warranty... 07 07 08 09 TECHNICAL SUPPORT / INFORMATION Kia is a registered trademark and property of Kia Canada Inc. web resources: www.xpresskit.com www.directechs.com
Vehicle Application Guide Page Vehicles 011 010 009 AV-Panic Mode Activation DL-Arm Factory Security DL-Disarm Factory Security DL-Door Lock Control DL-Door Unlock DL-Driver Priority Unlock DL-Trunk / Hatch Release FOB-Control of aftermarket alarm with OEM remote PK-Immobilizer Bypass-Data No Key Req'd RS-Tach / RPM Output SS-Entry Monitoring ALL Door Pins SS-Entry Monitoring Driver Door Pin Kia Borrego (Smart Key) 1 1 1 D D D D D Magentis (Smart Key) D D D D Optima (Smart Key) D D D D Sorento (Smart Key) 3 D D D D D Sportage (Smart Key) * D D D D D Legend: D: Data-to-Data (DD) only AV: Horn & Lights Controls : DD and Wire-to-Wire (WW) DL: OE Door Lock & Alarm Controls FOB: Sync CAN Interface w /FOB Remote PK: Transponder & Immobilizer Override SS: Entry Point Status-Security ST: Function/Feature Status SS-Entry Monitoring Hood Pin SS-Entry Monitoring Trunk/Hatch Pin ST-Brake Status (foot brake) ST-Hand Brake Status ST-Ignition Status * Important note for Kia Sportage! This firmware is ONLY compatible with the H. hardware version for that vehicle. LOT.168 DLPKKIA H..S.x 0TT000001130009603010E MADE IN CANADA H..S.x Underside of module
Installation Type 1: 009-011 Kia Borrego Page 3 56 55 5 53 5 51 50 9 8 7 6 5 3 1 0 39 38 36 37 35 3 3 9 7 33 31 30 8 6 5 3 0 1 11 17 15 1 19 18 16 1 13 10 9 8 7 6 5 3 1 IPM - Driver Side Dash (Black) Fuses 1 3 5 6 7 8 9 10 11 11311516 1736 190135678930313333 3536 3738390135678950515 535 555657585960616636656667686970 717 Orange Light Switch- Left Side of Steering Column 9 8 1 7 6 5 3 18 17 16 15 1 13 1 11 10 Autolight, Green Light Orange Cut 87 85 (+) 1v 86 87a 30 Brake pedal 1 3 (+) Brake, Push-to-Start (PTS) Switch Right Side of Steering Column (-) Hood Input (+) 1 V (+) Ignition Diode on Starter wire is ONLY required in WW mode. (+) Starter Output (-) Trunk Output (-) Unlock Output (-) Lock Output (-) GWR (status 1) Output TX RX (+) 1 V Remote Starter (-) GWR (status ) Output (-) Parking Lights (AC) Tach Input (+) Brake Status Input (-) Door/Trunk Sense Input Black 7 8 9 30 31 3 33 3 35 36 37 38 39 1 15 16 17 18 19 0 1 3 5 6 1 3 5 6 7 8 9 10 11 1 13 1 3 5 6 7 8 9 10 Pink Black/Orange +1VDC Driver Side Kick Panel XKDD65 1: (+) 1 V : RX 3: : TX 1: /: (-) GWR (status) Input 3: Light Green: (-) Lock Input 5: : (-) Unlock Input 6: /: (-) Trunk Input 7: Violet: (+) Starter Input 8: Pink: (+) Brake Input 9: : (+) 1 V Input 10: Black: Input 15: Yellow: (+) Push-to-Start (PTS) Output 16: Brown: (+) 1 V 19: Tan: FTCAN Low 0: Tan/Black: FTCAN High 0 These vehicles do NOT support virtual tach. Tach must be connected physically. PDM - Right Side of Steering Column : - PDM : Green: (-) Door/Trunk Sense Output 1: - : - : Pink/: (+) Brake Status Output* 1: /: (-) FOB IN Output* Programming Button Key Port - Right Side of Steering Column 1 3 5 6 7 8 9 13 17 0 1 16 19 11 15 18 10 1 1 3 5 6 7 8 9 10 Not required in DD mode. * If the kit you have purchased does not include a -pin black harness to accommodate these wires, use a DD or relay pack harness. Wires are listed by pin numbers. This display is not representative of connector pin layouts, which are often stacked.
Installation Type : 010 Kia Optima and Magentis Page (-) Driver Door Pin /Black 11 10 9 8 7 6 A 5 3 1 3 1 0 19 18 17 16 15 1 13 1 9 8 7 6 5 B 3 1 0 19 18 17 16 15 1 13 1 11 10 3 1 I/P Box Above Driver Kick Panel Connecteur G G Yellow/Black Yellow/ Black Yellow/Black BCM Above Brake Pedal A B C Gray/Orange (+) 1 V (+) Ignition (AC) Tach Input (+) Starter Output (-) Trunk Output (-) Unlock Output (-) Lock Output (-) GWR (status) Output TX RX (+) 1 V Remote Starter (-) Hood Input (-) Parking Lights (+) Brake Status Input (-) Door/Trunk Sense Input Brake Pedal 1 3 (+) Brake, Brown Black Diode on Starter wire is ONLY required in WW mode. +1VDC XKDD65 1: (+) 1 V : RX 3: : TX 1: /: (-) GWR (status) Input 3: Light Green: (-) Lock Input 5: : (-) Unlock Input 6: /: (-) Trunk Input 7: Violet: (+) Starter Input 8: Pink: (+) Brake Input 9: : (+) 1 V Input 10: Black: Input 19: Tan: FTCAN Low 0: Tan/Black: FTCAN High 0 : - : Green: (-) Door/Trunk Sense Output 1: Violet/: (-) Autolight Off Output : - : Pink/: (+) Brake Status Output* 1: /: (-) FOB IN Output* Programming Button Orange 8 7 6 5 C 3 1 18 17 16 15 1 13 1 11 10 9 These vehicles do NOT support virtual tach. Tach must be connected physically. Key Port - Under Center Armrest 1 3 5 6 7 Not required in DD mode. * If the kit you have purchased does not include a -pin black harness to accommodate these wires, use a DD or relay pack harness. Wires are listed by pin numbers. This display is not representative of connector pin layouts, which are often stacked.
Installation Type 3: 011 Kia Sorento Page 5 These vehicles do NOT support virtual tach. Tach must be connected physically. Green/Orange Driver Door Detection Switch 1 3 5 6 7 8 9 10 11 Fuses 1 3 5 6 7 8 9 10 11 1 13 1 15 16 17 18 19 0 /Black 1 3 5 6 7 8 9 10 11 1 13 1 1516 5 6 17 18190 1 3 1 3 5 6 7 8 9 10 11 113115161718190 IPM - Driver Side Dash (front view) Green Brake pedal 1 15 1 16 17 18 19 0 1 3 5 6 3 1 3 5 6 7 8 9 10 11 1 13 (+) Brake, Yellow ( cyl) Green/Black (6 cyl) (+) 1 V Diode on Starter wire is ONLY required in WW mode. (+) Starter Output (-) Hood Input (-) Parking Lights (-) Trunk Output (-) Unlock Output (-) Lock Output (-) GWR (status) Output TX RX (+) 1 V Starter Remote (+) Ignition (AC) Tach Input (+) Brake Status Input (-) Door/Trunk Sense Input /Orange IPM - Driver Side Dash (rear view) 9 10 111 131 15 16 1 3 5 6 7 8 +1VDC XKDD65 1: (+) 1 V : RX 3: : TX 1: /: (-) GWR (status) Input 3: Light Green: (-) Lock Input 5: : (-) Unlock Input 6: /: (-) Trunk Input 7: Violet: (+) Starter Input 8: Pink: (+) Brake Input 9: : (+) 1 V Input 10: Black: Input 19: Tan: FTCAN Low 0: Tan/Black: FTCAN High 0 : - PDM PDM - Behind the IPM Programming Button 1 3 5 6 7 8 9 13 17 0 1 16 19 11 15 18 10 1 : Green: (-) Door/Trunk Sense Output 1: Violet/: (-) Autolight Off Output : - : Pink/: (+) Brake Status Output* 1: /: (-) FOB IN Output* / Orange Not required in DD mode. * If the kit you have purchased does not include a -pin black harness to accommodate these wires, use a DD or relay pack harness. Wires are listed by pin numbers. This display is not representative of connector pin layouts, which are often stacked.
Installation Type : 011 Kia Sportage E - (see back of I/P Junction Box) Page 6 I/P Junction Box Left Side of Dash Panel Fuses CAN Low, CAN High, Smart Key Control Module D - Above Passenger Kick Panel 13 1 11 10 9 8 7 6 5 3 1 6 5 3 1 0 19 18 17 16 15 1 3 1 11 10 9 8 7 6 5 1 0 19 18 17 16 15 1 13 3 1 30 5 9 8 7 6 5 1 0 39 38 37 36 35 3 31 53 5 51 50 9 8 7 6 5 3 33 3 3 1 Black 13 1 11 10 9 8 7 6 5 3 1 (-) Hand Brake (AC) Tach Input (+) 1 V (+) Ignition (-) Parking Lights (+) Accessory (+) Ignition 1 (+) Start (-) Trunk Output (-) Unlock Output (-) Lock Output (-) GWR (status) Output TX RX (+) 1 V Starter Remote (+) Brake Status Input (-) Door/Trunk Sense Input Multifunction Switch (Light) - Steering Column XKDD65 Brake Pedal 1 3 (+) Brake, Green EMS Com, /Orange +1VDC 1: (+) 1 V : RX 3: : TX 1: /: (-) GWR (status) Input 3: Light Green: (-) Lock Input 5: : (-) Unlock Input 6: /: (-) Trunk Input 8: Pink: (+) Brake Input 9: : (+) 1 V Input 10: Black: Input 11: Black/ 1: Yellow/Black: 1: : Data 15: Yellow: Data 17: Orange 19: Tan: FTCAN Low 0: Tan/Black: FTCAN High 0 : - : Green: (-) Door/Trunk Sense Output 1: - : - : Pink/: (+) Brake Status Output* 1: - Programming Button 8 7 6 5 3 1 C 16 15 1 13 1 11 10 9 Smart Key Control Module C - Underneath Right A-Pillar D Smart Key Control Module Driver Kick Panel These vehicles do NOT support virtual tach. Tach must be connected physically. Not required in DD mode. * If the kit you have purchased does not include a -pin black harness to accommodate these wires, use a DD or relay pack harness. Wires are listed by pin numbers. This display is not representative of connector pin layouts, which are often stacked.
Module Programming Page 7 RUN SAFE When enabled, run safe will turn off the car engine if a door is opened. To disable run safe, press the UNLOCK button on the remote. Run safe will auto-enable 5 seconds after all doors are closed, and it will also enable if a LOCK command is sent. To perform take over, run safe must be disabled and the key must be inside the vehicle. Note that for Type, Takeover is not possible. The vehicle will shut down if a door is opened. Refer to the LED Diagnostics section on page 8 for more information and for troubleshooting purposes. 1 If connected in DD: Connect the -pin DD and the 0-pin harnesses. If connected in WW: Connect the 0-pin harness. Caution! The 0-pin connector can be easily plugged in backwards. The LED turns ON solid. -pin 0-pin On Solid Connect 3 5 one or both of the other -pin harnesses, depending on the requirements of each installation types. Make sure the key is inside the vehicle. Press the Push-to-Start button twice to turn the ignition ON without pressing on the brake pedal. The LED will stay ON solid for 3 seconds, then turn OFF. For Type, the LED will flash, then turn ON for 3 seconds before turning OFF. Press the Push-to-Start button once more to turn the ignition OFF. The module is programmed and ready to use. Resetting the Module 1 3 Disconnect the module from any power source. Press and HOLD the Integrated Programming Button (IPB). While holding the button, connect the module to the power source. PUSH Wait until the red LED flashes once and release the Integrated Programming Button (IPB). Press x ENGINE START STOP -pin & Press & Hold HOLD On x3 Secs PUSH Key Inside the Vehicle & Press 1x & ENGINE START STOP Off Disconnect from Power & Flashes x1 Connect to Power Release
LED Diagnostics Page 8 LED Status Description Troubleshooting Module Programming x3 secs x3 secs Off Solid Flashes slowly Solid for 3 seconds and then off Flashes, turns on solid for 3 seconds and then off Module has no power. Data Bus type cannot be detected. TYPE ONLY Bypass cannot be detected. Module is already or was successfully programmed. Module is already or was successfully programmed. Make sure the DD harness is connected or the 1V is present between the red and black wires. Make sure the connections to the CAN Bus are correct, then press the Push-to-Start button twice to turn the ignition ON. Make sure the connections to the EMS Com are correct, then press the Push-to-Start button twice to turn the ignition ON. Normal operation. Normal operation. x1 Flashes once quickly Module was reset. Normal operation. Active Ground While Running x1 sec Solid Off Incorrect behavior. Ground while running (status) off. Flashes for 1 second A command is processing. Normal operation. Flashes Ground while running (status) on. Normal operation. Inactive Ground While Running Off Ground while running (status) is off. Normal operation. Data is not processing correctly. Disconnect the power from the module and power up. Make sure the module was programmed, i.e. the DD harness is properly connected or the ground while running (status) wire is connected (if in WW mode). x1 sec Flashes for 1 second A command is processing. Normal operation. Solid Flashes Incorrect behavior. Ground while running (status) on. Data is not processing correctly. Disconnect the power from the module and power up. Module did not receive ground while running (status) off. Make sure the DD harness is properly connected or the ground while running (status) wire is not shorted to ground.
Limited One-Year Consumer Warranty Page 9 For a period of ONE YEAR from the date of purchase of a Directed Electronics remote start or security product, Directed Electronics. ( DIRECTED ) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, the security or remote start accessory piece (hereinafter the Part ), which proves to be defective in workmanship or material under normal use, provided the following conditions are met: the Part was purchased from an authorized DIRECTED dealer; and the Part is returned to DIRECTED, postage prepaid, along with a clear, legible copy of the receipt or bill of sale bearing the following information: consumer s name, address, telephone number, the authorized licensed dealer s name and complete product and Part description. This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to its intended purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defect in materials or construction. TO THE MAXIMUM EXTENT ALLOWED BY LAW, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NON INFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING DEALERS OR INSTALLERS. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER S PURCHASE PRICE OF THE PART. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR AT DIRECTED S OPTION THE PART AS DESCRIBED ABOVE. Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights and you may also have other rights that vary from State to State. DIRECTED does not and has not authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this Part.90-0007 07-06 This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the select vehicle list upon completion of compatibility testing. Visit website for latest vehicle application guide. DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for any consequential damages sustained in connection with the part(s) installation. The manufacturer and it s distributors will not, nor will they authorize any representative or any other individual to assume obligation or liability in relation to the interface kit / data bus interface part(s) other than its replacement. N.B.:Under no circumstances shall the manufacturer and distributors of this product be liable for consequential damages sustained in connection with this product and neither assumes nor authorizes any representative or other person to assume for it any obligation or liability other than the replacement of this product only. PROTECTED BY U.S. PATENTS: 5,719,551; 6,011,60 B1 *;6,3,00 B1; 6,9,16 B1; 6,75,17 B1; 6,97,731 B1; 6,36,876 B1; 6,39,53 B1; 6,59,1 B; 6,696,97 B; 6,756,885 B1; 6,756,886 B; 6,771,167 B1; 6,81,89 B1; 6,9,750 B1; 7,010,0 B1; 7,015,830 B1; 7,031,86 B1; 7, 06,16 B1; 7,061,137 B1; 7,068,153 B1; 7,05,679 B1; CDN.PATENT:,30,8;,1,991;,15,011;,15,03;,15,07;,15,038;,15,01;, 0, 97;,6,670;,5,089 EUROPEAN PATENT: 1,053,18 PAT.PENDING:,91,306; MADE IN CANADA