Sun offers sandwich and subplate mounted bodies for most of its cartridge functions. hese mounting configurations are complete circuit elements that mount under directional control valves. Similar to other Sun mounting configurations, the sandwich and subplate bodies are available in aluminum and ductile iron material. he sandwich and subplate bodies are available in five different interface patterns as shown below: Mounting of ISO 0 Sandwiches Sun s ISO 0 sandwich bodies are designed for multi-functional use to permit maximum circuit flexibility. Due to this versatility, the ISO 0 sandwich bodies do not have a counterbore for installing O-ring seals. Instead, Sun uses a special seal plate with a raised NI and a locating NOCH. Sun bodies incorporate oversize, symmetrical mounting holes to allow the bodies to be rotated about the NI axis and the longitudinal axis as shown in Figure. about the NI axis enables the and port connections to be interchanged and rotation about the longitudinal axis enables the and ports to be interchanged. ll Sun seal plates are manufactured to current industry standards regarding port and mounting bolt locations. Each Sun D0 sandwich body is supplied with a NI locating hole which is drilled on each mounting face to position the body in the correct relationship to the ports and mounting holes. o further ensure that all ISO 0/NF D0 ISO 05/NF D05 ISO 05/D05 with ISO 05/D05 with ISO 07/NF D07 ISO 08/NF D08 and U.S. and CEO.50 Diameter - laces for -0 O-rings.0 Diameter laces on the xis Longitudinal xis Locating in Hole NOCH NI xis NI xis.05.0 Locating in on the Longitudinal xis Figure : ody Reference bodies are located properly, all ISO 0 sandwich bodies are stamped with an arrow (or arrows) to show the relationship to the notch in the seal plate (see Figure ). Multi-function bodies are NOCH stamped for all possible mounting positions and all positions should be carefully inspected to be sure the intended function is correctly installed. ISO 0 stamped with numbers to orient body for desired function he function symbols on the data pages for Sun s ISO 0 sandwich bodies are shown with numbers (,,,) in the upper right and lower left hand corners. hese numbers correspond to numbers stamped on the face of the bodies and designate the functionality of the product. ecause many of these bodies can be used for different functions, the bodies are stamped to help the user orient the body for the function desired. Some bodies can be mounted in four different orientations, as shown in Figure on the facing page. he example below shows G. s demonstrated by the function symbols, this single body can be used to achieve four different functions: Meter in, Meter out, Meter in, and Meter out. he body drawing only indicates the Meter out and Meter in orientations because only one face of the body is shown. he Meter out and Meter in functions are shown in the symbols with the numbers and, which correspond to the numbers stamped on the opposite face of the Example for ISO 0 bodies using subplate G. SE egin with body view showing stamped number in lower left corner. Note the location of,,, and ports and the position of the cavity. his position places the port of the sandwich nearest to the viewer.he sandwich is now oriented for the meter out function. Meter out Function SE Rotate the sandwich on the longitudinal axis to orient body for meter in function. Meter in Function in in 0 US Selected ssemblies Catalogue #999-90-9
SE Rotate the sandwich on the nib axis to orient body for meter in function. Meter in Function SE Rotate the sandwich on the longitudinal axis to orient body for meter out function. Meter out Function Sandwich ssemblies ISO 0 / CEO FLOW CONROL VLVES FULL DJUSLE NEEDLE WIH REVERSE FREE FLOW CHECK p t b a ssembly Model Code* rices luminum Ductile Iron NCC-L*N-G *dd modifier /S to order Ductile Iron for pressure rating over 000 psi. in in p t b a - Cavity.05 MEER IN NOCH MEER OU NOCH.5 NOCH L Control ssembly of ISO 0 Sandwiches. lace the Sun seal plate, with the NI facing upward, in the proper position to correctly align the mounting holes and fluid ports. t this time, the NOCH in the seal plate must be adjacent to the port of the valve interface. See Figure.. osition the Sun sandwich body so that the control NOCH arrow for the required function points to the NOCH in the seal plate. See Figure.. Move the sandwich body as required to engage the NI on the seal plate with the clearance hole in the Meter in SSEML NOE: In every installation, the seal plate nib must be oriented toward the directional control valve and away from the subplate or manifold. ll locating NIS in the sandwich valve stack must point in the same direction.. fter determining the correct alignment of the sandwich body to the seal plate, lift the body and plate together, turn the assembly over and locate the correct hole in which to press the locating pin. he locating pin is shipped separately. ress the pin, serrated end first, into the body until it stops. he pin must protrude below the seal plate to positively align with the mounting surface. If a valve.50 Figure ll sandwich bodies shown below are.75 wide.70.0 Max. Locating in () 0 O rings Figure : ssembly Function Sun Sandwich FULL DJUSLE NEEDLE ssembly Model Code* Meter-In Meter-Out Meter-In Meter-Out rices luminum Ductile Iron NCC-L*N-G *dd modifier /S to order Ductile Iron for pressure rating over 000 psi. Locating in Sun Seal late Subplate or Manifold stack requires disassembly at anytime, the pin should not be removed. It will simplify the reassembly of the valve stack. 5. fter all the body alignments have been determined and all pins installed, assemble the valve stack in the required functional order. Make sure all the O-rings are properly positioned. Install the directional control valve on top of the stack and tighten the stud nuts alternately to the proper torque of 0-5 lb. in. Mounting ISO 05 Sun ISO 05 sandwich bodies are available for many mounting configurations. he standard ISO 05/NF D05 is offered with two methods of sealing the fluid interface. he sealing method depends on the ability of the body to be rotated about its axis. Sandwich bodies that can be rotated will use a Sun seal plate supplied with the Non rotating bodies will have counterbores machined into the body sealing surface for O-ring placement. he ISO 05 sandwich body can only be rotated about the NI axis referred to in the ISO 0 sandwich section. here is no NI on the ISO 05 subplate, it is used only for axis reference. Longitudinal axis rotation is not possible due to the lack of symmetry of the fluid ports. Mounting ISO 05, Sun ISO 05, sandwich bodies are furnished with pilot and drain connections. Due to the differences in the U.S. and European seal plates, none are supplied with these bodies. hey US Selected ssemblies Catalogue #999-90-9
must be ordered separately to correctly match the other valve bodies in the stack. See the chart below for various product brands and part number information. U.S. for use with. Verify that the correct seal plates have been selected (if required) and position the sandwich body so that the fluid ports are correctly aligned and the correct port ( or ) is being controlled.. fter determining the proper alignment of all the sandwich bodies, assemble the valve stack in the required functional order. Make sure all the O-rings are properly positioned. Install the directional valve and tighten the studnuts alternately to the proper torque of 05 0 lb. in. Studkits for ISO 0 and ISO 05 European (CEO) for use with Double Q* 0 Rexroth WEH 0 arker Hannifin DW osch Racine FD **HS 0 Dynex Rivett 6600 OH Snap ite DG0 Kit #990 0 009 Kit #990 0 0 Includes: Includes: 9 008 seal plate 99 009 seal plate 5 500 00 0 una-n O-rings 500 00 00 una-n O rings 5 500 00 0 una-n O-rings 500 00 0 una-n O-rings o simplify the installation of ISO 0 and ISO 05 sandwiches, Sun offers uncut (can be cut to length in the field) or precut studkits in both inch and metric standard threaded rod. Once the rods are installed in a subplate or manifold, they act as a guide in assembling the sandwich body stack. fter the directional control valve is assembled on top of a stack, Sun studnuts are used to retain the assembled stack. he inch and metric studrods are both made of high tensile, fully threaded SM--9 Grade material with the following mechanical properties: 5,000 psi minimum tensile strength. 05,000 psi minimum yield point. 6 Rc hardness. he studnuts are special hex socket nuts with the following features: n outside diameter equivalent to a standard socket head cap screw. Full thread engagement as shown below. Mechanical stop between the internal hex and the thread to prevent the hex wrench from being pushed out of its socket. ISO 0 Studkits (recommended torque 0-5 lb. in.) Inch Standards ISO 0 Internal Hex Size 5/ U.S. mm metric 0- (art #50005) and M5 (art #50009) Studnuts..65 ISO 05 Internal Hex Size /6 U.S. 5 mm metric /-0 (art #5000) and M6 (art #50008) Studnuts.56.000 () 0 Studnuts and () approximately 7 long 0 studrods Kit # 990 () 0 Studnuts and () approximately long 0 studrods Kit # 990 (50) 0 Studnuts and (0) approximately 6 long 0 studrods Kit # 990 (50) 0 Studnuts only Kit # 99550 () 0 Studnuts and () 0 studrods cut to customer specified length (±.06 ) Kit # 99650 Metric Standards () M5 Studnuts and () approximately 7 long M5 studrods Kit # 99 () M5 Studnuts and () approximately long M5 studrods Kit # 99 (50) M5 Studnuts and (0) approximately 6 long M5 studrods Kit # 99 (50) M5 Studnuts only Kit # 99750 () M5 Studnuts and () M5 studrods cut to customer specified length (±.06 ) Kit # 99850 ISO 05 Studkits (recommended torque 05-0 lb. in.) Inch Standards () / 0 Studnuts and () approximately 7 long / 0 studrods Kit # 9900 () / 0 Studnuts and () approximately long / 0 studrods Kit # 9900 (50) / 0 Studnuts and (0) approximately 6 long / 0 studrods Kit # 99500 (50) / 0 Studnuts only Kit # 99500 () / 0 Studnuts and () / 0 studrods cut to customer specified length (±.06 ) Kit # 99600 Metric Standards () M6 Studnuts and () approximately 7 long M6 studrods Kit # 990 () M6 Studnuts and () approximately long M6 studrods Kit # 990 (50) M6 Studnuts and (0) approximately 6 long M6 Studrods Kit # 990 (50) M6 Studnuts only Kit # 99700 () M6 Studnuts and () M6 studrods cut to customer specified length (±.06 ) Kit # 99800 US Selected ssemblies Catalogue #999-90-9
SUDROD LENGH DEERMINION CHR Solenoid Sandwich Subplate orque: 5 lb. in. *.0 rojection into Studnut otal Height of Stack.8 rojection into Subplate ISO 0 otal Studrod Effective Length olt Length ±.06 orque: 0 lb. in. ISO 05 and ISO 05, Model inches* Model inches* Continental E0M.65 VSM. Continental VS5M.65 E05M. Double (Vickers) Q*.56 Q* 5.05 arker Hannifin DVW.50 DW.9 Racine osch.5ng6.87 /.8 Rexroth WR6.6 WE0, WEH0.8 Dynex/Rivett 6500 Series 0. 6500 0.8 Vickers/0 DGV.56 DGS.05 Vickers/60 DGV.8 DGV5.8 Nachi SSG0. SSG0,E0,E0.8 Solenoid Sandwich Subplate.56 rojection into Studnut. rojection into Subplate * he dimension was accurate as of the publication date of this catalogue. Verify in the applicable manufacturers literature. * otal Studrod Length Effective ±.06 otal olt Length Height of Stack US Selected ssemblies Catalogue #999-90-9
NOES US Selected ssemblies Catalogue #999-90-9