Directed Digital System

Directed Digital System HYUNDAI2 Firmware Specific Guide This product is intended for installation by a professional installer only! Attempts to install this product by a person other than a trained professional may result in severe damage to a vehicle s electrical system and components. 205 Directed, Vista, CA Directed Digital System 205-

Contents Warning! Safety first... 3 Introduction... 4 Vehicle application guide... 4 Wiring connections... 5 Main power harness (H), 2-pin thick gauge connector... 5 Auxiliary output harness (H2), 6-pin black connector... 5 Analog harness (H3), 8-pin white connector... 6 MC50 harness (H4), 8 thick-gauge wires (optional)... 6 Installation... 7 Type... 7 Type 2... 8 Type 3... 9 Type 4... 0 Type 5... Type 6... 2 Type 7... 3 Type 8... 4 Type 9... 5 Vehicle wiring reference charts... 6 Connecting the module... 26 Important!... 26 Manual or automatic transmission selection... 26 Optional sensors... 27 RF kits... 27 When used in conjunction with SmartStart... 27 Module programming... 28 LED diagnostics and troubleshooting... 29 Module reset... 3 Hard reset... 3 Learning the Tach (not needed with Virtual Tach)... 32 Initializing Virtual Tach (not needed with hardwired or data tach applications)... 32 Limited lifetime consumer warranty... 33 Quick Reference Guide Viper, Clifford, Python, Avital & Automate... 34 Quick Reference Guide Autostart... 37

Warning! Safety first The following safety warnings must be observed at all times: Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer. When properly installed, this system can start the vehicle via a command signal from the remote control. Therefore, never operate the system in an area that does not have adequate ventilation. The following precautions are the sole responsibility of the user; however, authorized Directed dealers should: Never use a test light or logic probe when installing this unit. Always use a multimeter. Never operate the system in an enclosed or partially enclosed area without ventilation (such as a garage). When parking in an enclosed or partially enclosed area or when having the vehicle serviced, the remote start system must be disabled using the installed toggle switch. It is the user s sole responsibility to properly handle and keep out of reach from children all remote controls to assure that the system does not unintentionally remote start the vehicle. USER MUST INSTALL A CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING AREA ADJACENT TO THE VEHICLE. ALL DOORS LEADING FROM ADJACENT LIVING AREAS TO THE ENCLOSED OR PARTIALLY ENCLOSED VEHICLE STORAGE AREA MUST REMAIN CLOSED AT ALL TIMES. Use of this product in a manner contrary to its intended mode of operation may result in property damage, personal injury, or death. Except when performing the Safety Check outlined in this installation guide, () Never remotely start the vehicle with the vehicle in gear, and (2) Never remotely start the vehicle with the keys in the ignition. The user is responsible for having the neutral safety feature of the vehicle periodically checked, wherein the vehicle must not remotely start while the car is in gear. This testing should be performed by an authorized Directed dealer in accordance with the Safety Check outlined in this product installation guide. If the vehicle starts in gear, cease remote start operation immediately and consult with the user to fix the problem immediately. OPERATION OF THE REMOTE START MODULE IF THE VEHICLE STARTS IN GEAR IS CONTRARY TO ITS INTENDED MODE OF OPERATION. OPERATING THE REMOTE START SYSTEM UNDER THESE CONDITIONS MAY RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY. IMMEDIATELY CEASE THE USE OF THE UNIT AND REPAIR OR DISCONNECT THE INSTALLED REMOTE START MODULE. DIRECTED WILL NOT BE HELD RESPONSIBLE OR PAY FOR INSTALLATION OR REINSTALLATION COSTS. Remote starters for manual transmission pose significant risks if not properly installed and operated. When testing to ensure the installation is working properly, only remote start the vehicle in neutral gear, on a flat surface and with a functional, fully engaged parking brake. Do not allow anyone to stand in front of or behind the vehicle. This product should not be installed in any convertible vehicles, soft or hard top with a manual transmission. Installation in such vehicles may pose certain risk. 3

Introduction The HYUNDAI2 firmware for Directed Digital Systems is a complete solution for remote start, security (if applicable), bypass interface, and convenience needs compatible with specific Hyundai and Kia vehicles. Warning! This module can only be programmed via the web tool, which can be found on www.directechs.com or using the Directechs Mobile application for smartphones. Features and functions will become accessible when you connect the module using the XKLoader. Vehicle application guide The following table lists the vehicles and features which are compatible with this product. The number assigned to each year allows you to determine which installation type should be used for your vehicle. Vehicles 205 204 203 202 20 PK-Immobilizer Bypass-Data No Key Req'd AV-Panic Mode Activation DL-Arm Factory Security DL-Disarm Factory Security Hyundai Elantra (Smart Key) 2 2 Elantra Coupe (Smart Key) Elantra GT (Smart Key) 2 2 2 Veloster (Smart Key) 3 3 3 3 Kia Optima (Smart Key) 5 5 4 4 4 Optima Hybrid (Smart Key) 5 4 4 4 Rio (Smart Key) 9 9 9 9 Rondo (Smart Key) 6 6 Sorento (Smart Key) 7 7 Sportage (Smart Key) 8 8 8 8 DL-Door Lock Control DL-Door Unlock DL-Driver Priority Unlock DL-Trunk / Hatch Release EIPS FOB-Control of aftermarket alarm with OEM remote RS-3x LOCK START (Start control using OEM Remote) RS-3x LOCK STOP (Stop control using OEM Remote) RS-Remote Start Takeover mode RS-Tach / RPM Output SS-Entry Monitoring ALL Door Pins SS-Entry Monitoring Driver Door Pin SS-Entry Monitoring Hood Pin SS-Entry Monitoring Trunk/Hatch Pin ST-Brake Status (foot brake) Legend: PK: Transponder & Immobilizer Override AV: Horn & Lights Controls DL: OE Door Lock & Alarm Controls EIPS: Engine Idle Protection System FOB: Sync CAN Interface w/ FOB Remote RS: Remote Start & Engine Controls SS: Integrated Security & Monitoring ST: Function/Feature Status 4

Wiring connections The wiring connections listed below are generic to this firwmare. Main power harness (H), 2-pin thick gauge connector Conn./Pin Color Description H/ White Relay 3 COM Ignition 2 Output H/2 White/Brown Relay 3 N.O. (+) Power 2 Volt H/3 Brown/Red Relay 2 N.O. (-) Ground H/4 Yellow/Red Relay 2 COM EIPS Alert H/5 Orange/Red Relay 2 N.C. No Connection H/6 Yellow Relay COM Ignition Output H/7 White Relay 3 COM Ignition 2 Output H/8 White/Brown Relay 3 N.O. (+) Power 2 Volt H/9 Black (-) Ground H/0 Red (+) 2 Volt (Battery) H/ Orange/Yellow Relay N.C. No Connection H/2 Brown Relay N.O. (+) Power 2 Volt Auxiliary output harness (H2), 6-pin black connector Conn./Pin Color Description H2/ Violet/Brown No Connection H2/2 Yellow/Black No Connection H2/3 Orange/Black EMS COM Data H2/4 Tan HS CAN Low H2/5 Tan/Black HS CAN High H2/6 Light Green No Connection H2/7 Orange/Green FT CAN High H2/8 Orange/Brown FT CAN Low H2/9 Violet/Green No Connection H2/0 Green/Black (-) Parking Lights 2 H2/ White/Violet RAP Off (Type 3, 7 & 9) 2 H2/2 White/Red No Connection 2 H2/3 Lt. Blue/Black (-) Push-to-Start 2 H2/4 Green/Red (+) Starter 2 H2/5 N/A No Connection H2/6 Violet/Yellow No Connection. If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. 2. If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. Note that they are low current and a relay may be necessary. 5

Analog harness (H3), 8-pin white connector Conn./Pin Color Description H3/ Lt. Blue/Red No Connection H3/2 Black/White No Connection 2 H3/3 Gray (-) Hood Input 2 H3/4 N/A No Connection H3/5 Gray/Black No Connection 2 H3/6 Violet/White No Connection 2 H3/7 Dark Blue No Connection H3/8 Brown/Black No Connection H3/9 Red/White No Connection H3/0 White/Green No Connection 2 H3/ Yellow/Green No Connection 2 H3/2 Blue/Red No Connection H3/3 Light Blue No Connection 2 H3/4 Pink/Yellow No Connection H3/5 Dark Green No Connection H3/6 Brown/White No Connection 2 H3/7 Brown (+) Siren Output H3/8 Blue/White No Connection MC50 harness (H4), 8 thick-gauge wires (optional) Conn./Pin Color Description H4/ Pink/White No Connection H4/2 Red/White No Connection H4/3 Pink No Connection H4/4 Red No Connection H4/5 Orange No Connection H4/6 Red No Connection H4/7 Green No Connection H4/8 Violet No Connection. If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. Note that they are low current and a relay may be necessary. 2. These connections are only required if the corresponding statuses are not supported by the firmware. See "Vehicle application guide" on page 4 for a list of compatible features. 6

27 4 28 5 2 29 4 3 8 32 9 20 7 34 8 22 36 0 24 38 25 2 39 26 3 2 23 22 2 20 9 7 6 5 4 3 7 9 20 2 23 24 2 4 6 8 9 2 27 28 3 3 5 32 6 9 Installation Type Refer to "Vehicle wiring reference charts" on page 6 for more information on vehicle-specific connections. FT CAN Low: Yellow/Orange or White, pin White conn. I/P-G (Back of I/P Junction Box) 2 3 4 3 5 4 6 5 6 7 8 7 9 8 20 9 0 2 22 2 23 24 FT CAN High: White/Orange or Brown, pin 3 Diagnostic Connector OBDII HS CAN High: White, pin 6 8 HS CAN Low: Yellow, pin 4 6 White Connector EM (Driver Kick Panel) 4 5 6 7 2 3 8 9 0 2 34 5 7 8 9 20 2 22 23 24 25 6 26 27 2829 30 32 33 34 3536 37 38 39 40 4 3 44 4546 47 42 43 48 49 50 5 52 5354 55 EMS COM Data: Brown/Orange, pin 0 I/P-F (MAIN) I/P-G (MAIN) I/P- H (MAIN) I/P Junction Box (rear) (left side of dash panel) (+) Ignition 2: Orange, pin White conn. M0-L (at Headlight Switch) 2 3 4 5 6 7 8 9 0 2 3 (-) Parking Lights: Pink or Orange, pin 2 (-) PTS: Yellow/Black, pin 2 3 4 5 6 7 8 9 0 2 Black Conn. M04 (at Push-to-Start button) Black conn. I/P-F (Back of I/P Junction Box) 2 3 4 5 6 7 8 9 0 2 3 4 5 678920 222232425 26 27 282930 33233 3435363738 39 (+) Starter: Yellow, pin 39 Siren Hood Pin EMS COM Data: Orange/Black: 3 HS CAN Low: Tan: 4 HS CAN High: Tan/Black: 5 FT CAN High: Orange/Green: 7 FT CAN Low: Orange/Brown: 8 (-) Parking Lights: Green/Black: 0 (-) Push-to-Start: Lt. Blue/Black: 3 (+) Starter: Green/Red: 4 [3] (-) Hood Input: Gray: 3 [] (+) Siren Output: Brown: 7 6 Black 3 Wh 7 White 8 White 2 Wh Manual/Auto. Transmission Type Prog. Button 6 Green 2 Bk 4 White 4 Red 2 White [2] (-) Horn: White, pin 34 [2] (-) Horn: White, pin 44 Remote Start Safety Override Switch 2: Brown: (+) 2V 0: Red: (+) 2V 9: Black: (-) Ground 6: Yellow: Ignition The Remote Start Safety Override Switch MUST be in the ON position. 4: Yellow/Red: EIPS Alert [2] 3: Brown/Red: (-) Ground [2] 2 & 8: White/Brown: (+) 2V & 7: White: Ignition 2 Elantra 203 made in US only. OR All other Type Elantras (+) 2V (+) Ignition : Pink, pin 27 [] The siren is optional. [2] This connection is only required when the EIPS (Engine Idle Protection System) feature is activated. [3] The installation of an aftermarket hood pin is only required on vehicles that are not equipped with a factory hood pin. With the exception of the OBDII diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise). 7

27 4 28 5 2 29 4 3 8 32 9 20 7 34 8 22 36 0 24 38 25 2 39 26 3 2 23 22 2 20 9 7 6 5 4 3 7 9 20 2 23 24 2 4 6 8 9 2 27 28 3 3 5 32 6 9 Type 2 Refer to "Vehicle wiring reference charts" on page 6 for more information on vehicle-specific connections. FT CAN Low: Orange, pin White Conn. I/P-G (Back of I/P Junction Box) 2 3 4 3 5 4 6 5 6 7 8 FT CAN High: Green, pin 3 7 9 8 20 9 0 2 22 2 23 24 Diagnostic Connector OBDII HS CAN High: White, pin 6 8 HS CAN Low: Yellow, pin 4 6 White Connector EM (Driver Kick Panel) 58 32 26 [ 2] (-) Horn: White, pin 52 57 56 55 54 53 52 5 45 44 43 42 4 47 46 37 36 35 34 33 3 30 23 22 2 20 9 25 24 5 4 3 2 8 7 6 5 4 0 9 50 49 40 39 29 28 8 7 3 2 48 38 27 6 [ 2] (-) Horn: White, pin 4 I/P-F (MAIN) I/P-G (MAIN) I/P- H (MAIN) I/P Junction Box (rear) (left side of dash panel) (+) Ignition 2: Orange, pin White conn. M0-L (at Headlight Switch) 2 3 4 5 6 7 8 9 0 2 3 (-) Parking Lights: Pink, pin 2 (-) PTS: Yellow/Black, pin 2 3 4 5 6 7 8 9 0 2 Black Conn. M04 (at Push-to-Start button) Black Conn. I/P-F (Back of I/P Junction Box) 2 3 4 5 6 7 8 9 0 2 3 4 5 678920 222232425 26 27 282930 33233 3435363738 39 (+) Starter: Yellow, pin 39 Siren Hood Pin EMS COM Data: Orange/Black: 3 HS CAN Low: Tan: 4 HS CAN High: Tan/Black: 5 FT CAN High: Orange/Green: 7 FT CAN Low: Orange/Brown: 8 (-) Parking Lights: Green/Black: 0 (-) Push-to-Start: Lt. Blue/Black: 3 (+) Starter: Green/Red: 4 [3] (-) Hood Input: Gray: 3 [] (+) Siren Output: Brown: 7 EMS COM Data: Blue/Black or Brown/Orange, pin 2 6 Black 3 Wh 7 White 8 White 2 Wh Manual/Auto. Transmission Type Prog. Button 6 Green 2 Bk 4 White 4 Red 2 White Remote Start Safety Override Switch 2: Brown: (+) 2V 0: Red: (+) 2V 9: Black: (-) Ground 6: Yellow: Ignition For Elantra 203-204 GT The Remote Start Safety Override Switch MUST be in the ON position. 4: Yellow/Red: EIPS Alert [2] 3: Brown/Red: (-) Ground [2] 2 & 8: White/Brown: (+) 2V & 7: White: Ignition 2 OR For Elantra Sedan 204 (+) 2V (+) Ignition : Pink or White, pin 27 [] The siren is optional. [2] This connection is only required when the EIPS (Engine Idle Protection System) feature is activated. [3] The installation of an aftermarket hood pin is only required on vehicles that are not equipped with a factory hood pin. With the exception of the OBDII diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise). 8

7 9 Type 3 Refer to "Vehicle wiring reference charts" on page 6 for more information on vehicle-specific connections. White connector I/P-C (rear of I/P Junction Box) FT CAN Low: Yellow/Orange, pin 6 Diagnostic Connector OBDII [ 2] (-) Horn: White/Orange, pin 44 Black connector EM (Driver Kick Panel) White Connector EM (Driver Kick Panel) 2 3 4 3 5 4 6 5 6 7 8 7 9 8 20 9 0 2 22 FT CAN High: White/Orange, pin 5 2 23 24 (-) Parking Lights: Pink, pin HS CAN High: White, pin 6 8 HS CAN Low: Yellow, pin 4 6 5 3 20 52 42 32 2 2 53 54 55 56 57 58 43 44 45 46 47 48 49 33 34 35 36 37 38 39 22 23 24 25 26 27 28 2 3 4 5 6 7 8 3 4 5 6 7 8 59 50 40 29 9 9 60 4 30 0 6 3 4 5 6 7 2 3 2 34 5 8 9 0 7 8 9 20 2 22 23 24 25 26 27 2829 30 32 33 34 3536 37 38 39 40 4 44 4546 47 42 43 48 49 50 5 52 5354 55 EMS COM Data: Blue, pin 0 White conn. MF (Driver kick panel) I / P 9 8 6 5 0 8 7 6 5 4 28 27 26 25 24 23 36 38 37 45 56 55 54 I / P - E I / P - F - K F u s es 35 44 53 I / P 34 43 52 I / P I / P - M - N 42 5 - L 33 4 50 I / P - G I / P - H F u se P a n el ( f r o n ) t I/P Junction Box (left side of dash panel) (-) Driver Door Trigger: B r o w n, pin 7 4 3 2 3 2 20 9 22 2 32 3 30 29 40 39 49 48 47 48 (+) Starter: Yellow, pin 5 2 3 8 9 0 4 5 6 7 (+) Ignition 2: 2 3 4 5 6 Red, pin 4 White conn. I/P-F (I/P Junction Box) (-) PTS: Y ello w / B la ck, pin 2 3 4 5 6 7 8 9 0 2 White conn. M04 (at Push-to-Start button) (+) Ignition : Pink, pin 7 Veloster late 204 OR Veloster 202-203 & early 204 Siren Hood Pin EMS COM Data: Blue, pin 6 EMS COM Data: Orange/Black: 3 HS CAN Low: Tan: 4 HS CAN High: Tan/Black: 5 FT CAN High: Orange/Green: 7 FT CAN Low: Orange/Brown: 8 (-) Parking Lights: Green/Black: 0 Autolights/RAP Off: White/Violet: (-) Push-to-Start: Lt. Blue/Black: 3 (+) Starter: Green/Red: 4 [3] (-) Hood Input: Gray: 3 [] (+) Siren Output: Brown: 7 6 Black 3 Wh 7 White 8 White 2 Wh Manual/Auto. Transmission Type [2] (-) Horn: White/Orange, pin 44 Prog. Button 6 Green 2 Bk 4 White 4 Red 2 White White conn. I/P-L (I/P Junction box) Veloster Veloster 202-203 OR 2 3 4 late 204 & early 204 (+) 2V: Red, pin 2 Remote Start Safety Override Switch 2: Brown: (+) 2V 0: Red: (+) 2V 9: Black: (-) Ground 6: Yellow: Ignition The Remote Start Safety Override Switch MUST be in the ON position. 4: Yellow/Red: EIPS Alert [2] 3: Brown/Red: (-) Ground [2] 2 & 8: White/Brown: (+) 2V & 7: White: Ignition 2 [] The siren is optional. [2] This connection is only required when the EIPS (Engine Idle Protection System) feature is activated. [3] The installation of an aftermarket hood pin is only required on vehicles that are not equipped with a factory hood pin. With the exception of the OBDII diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise). 9

9 Type 4 Refer to "Vehicle wiring reference charts" on page 6 for more information on vehicle-specific connections. Diagnostic Connector OBDII HS CAN High: White, pin 6 Black conn. I/P-C White Connector EM (in driver kick panel) 8 HS CAN Low: Yellow, pin 4 6 F u ses I / P J u n ct io n B o x ( Left Side of Dash Panel ) 2 3 (+) 2V: Pink, pin EMS COM Data: Brown/Orange or Blue, pin 0 2 3 4 0 2 3 9 20 2 22 28 2930 3 36 3738 39 40 442 43 5 4 23 32 6 5 24 33 7 6 25 34 8 7 26 35 9 8 27 White conn. M0-L (at headlight switch) [2] (-) Horn: White, pin 42 (-) PTS: Yellow/Black, pin 2 6 7 3 8 4 5 9 0 Black Conn. M04 (at Push-to-Start button) 2 3 4 5 6 7 8 9 0 2 3 (-) Parking Lights: Pink, pin Black conn. I/P-E (Back of I/P Junction Box, located on left side of dash panel) (+) Ignition : Pink, pin (+) Starter: 2 3 4 5 6 7 8 9 0 2 3 Orange or Yellow, pin 26 4 26 (+) Ignition 2: 5 678920 222232425 Orange, pin 4 27 28 2930 33233 3435363738 39 Hood Pin FT CAN Low: Yellow/Orange, pin 38 FT CAN High: White/Orange, pin 25 Siren EMS COM Data: Orange/Black: 3 HS CAN Low: Tan: 4 HS CAN High: Tan/Black: 5 FT CAN High: Orange/Green: 7 FT CAN Low: Orange/Brown: 8 (-) Parking Lights: Green/Black: 0 (-) Push-to-Start: Lt. Blue/Black: 3 (+) Starter: Green/Red: 4 [3] (-) Hood Input: Gray: 3 [] (+) Siren Output: Brown: 7 6 Black 3 Wh 7 White 8 White 2 Wh Manual/Auto. Transmission Type Prog. Button 6 Green 2 Bk 4 White 4 Red 2 White Remote Start Safety Override Switch 2: Brown: (+) 2V 0: Red: (+) 2V 9: Black: (-) Ground 6: Yellow: Ignition The Remote Start Safety Override Switch MUST be in the ON position. 4: Yellow/Red: EIPS Alert [2] 3: Brown/Red: (-) Ground [2] 2 & 8: White/Brown: (+) 2V & 7: White: Ignition 2 [] The siren is optional. [2] This connection is only required when the EIPS (Engine Idle Protection System) feature is activated. [3] The installation of an aftermarket hood pin is only required on vehicles that are not equipped with a factory hood pin. With the exception of the OBDII diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise). 0

9 O R Type 5 Refer to "Vehicle wiring reference charts" on page 6 for more information on vehicle-specific connections. FT CAN Low: Yellow/Orange, pin White conn. I/P-G (Back of I/P Junction Box, located left side of dash panel) 2 3 4 5 6 7 8 9 0 2 3 4 5 67 8 9 20 222 23 24 FT CAN High: White/Orange, pin 3 Diagnostic Connector OBDII HS CAN High: White, pin 6 8 HS CAN Low: Yellow, pin 4 6 F u ses I / P J u n ct io n B o x ( Left Side of Dash Panel) Black Conn. I/P-C (front of I/P Junction box) 2 3 (+) 2V: Red, pin White Conn. EM (in driver kick panel) (+) Starter: Gray, pin 9 58 32 26 9 57 56 55 54 53 52 5 50 49 47 46 45 44 43 42 4 37 36 35 34 33 40 39 3 30 23 22 2 20 9 25 24 5 4 3 2 29 28 8 7 0 8 7 6 5 4 3 2 (+ ) Ignition 2: B la ck / O r a n g e, pin 2 EMS COM Data: Brown/Orange or Blue, pin 4 48 38 27 6 (+ ) Ignition 2: B la ck / O r a n g e, pin 9 [2] (-) Horn: White, pin 39 Optima H y b r id 20 4 Optima ( S m a r t K ey 20 ) 4 Black Conn. M04 (at Push-to-Start button) (+) Ignition : Pink, pin White conn. M0-L (at headlight switch) 2 3 4 5 6 7 8 9 0 2 3 (-) Parking Lights: Pink, pin (-) PTS: Yellow/Black, pin 2 3 4 5 6 7 8 9 0 2 Black conn. I/P-E (Back of I/P Junction Box, located left side of dash panel) 2 3 4 5 6 7 8 9 0 2 3 4 26 5 678920 222232425 27 282930 3323334 35363738 39 Siren Hood Pin EMS COM Data: Orange/Black: 3 HS CAN Low: Tan: 4 HS CAN High: Tan/Black: 5 FT CAN High: Orange/Green: 7 FT CAN Low: Orange/Brown: 8 (-) Parking Lights: Green/Black: 0 (-) Push-to-Start: Lt. Blue/Black: 3 (+) Starter: Green/Red: 4 [3] (-) Hood Input: Gray: 3 [] (+) Siren Output: Brown: 7 6 Black 3 Wh 7 White 8 White 2 Wh Manual/Auto. Transmission Type Prog. Button 6 Green 2 Bk 4 White 4 Red 2 White Remote Start Safety Override Switch 2: Brown: (+) 2V 0: Red: (+) 2V 9: Black: (-) Ground 6: Yellow: Ignition The Remote Start Safety Override Switch MUST be in the ON position. 4: Yellow/Red: EIPS Alert [2] 3: Brown/Red: (-) Ground [2] 2 & 8: White/Brown: (+) 2V & 7: White: Ignition 2 [] The siren is optional. [2] This connection is only required when the EIPS (Engine Idle Protection System) feature is activated. [3] The installation of an aftermarket hood pin is only required on vehicles that are not equipped with a factory hood pin. With the exception of the OBDII diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).

9 Type 6 Refer to "Vehicle wiring reference charts" on page 6 for more information on vehicle-specific connections. FT CAN Low: Blue, pin White conn. I/P-G (Back of I/P Junction Box, located left side of dash panel) 2 3 4 3 5 4 6 5 6 7 8 FT CAN High: Orange, pin 3 7 9 8 20 9 0 2 22 2 23 24 Diagnostic Connector OBDII HS CAN High: White, pin 6 8 HS CAN Low: Brown, pin 4 6 (+) Ignition : Pink, pin 58 (+) Ignition 2: White, pin 32 58 32 26 57 56 55 54 53 52 5 47 46 45 44 43 42 4 37 36 35 34 33 3 30 23 22 2 20 9 25 24 5 4 3 2 8 7 6 5 4 0 9 50 49 40 39 29 28 8 7 3 2 (+) Starter: Green, pin 49 48 38 27 6 White Connector EM (in driver kick panel) [2] (-) Horn: White, pin 7 EMS COM Data: Blue/Orange, pin 37 Black Conn. White conn. (at headlight switch) 2 3 4 5 6 7 8 9 0 2 3 4 5 6 White Conn. M04 (at Push-to-Start button) (-) Parking Lights: Pink, pin 4 (-) PTS: Yellow/Black, pin 2 3 4 5 6 7 8 9 0 2 Siren Hood Pin EMS COM Data: Orange/Black: 3 HS CAN Low: Tan: 4 HS CAN High: Tan/Black: 5 FT CAN High: Orange/Green: 7 FT CAN Low: Orange/Brown: 8 (-) Parking Lights: Green/Black: 0 (-) Push-to-Start: Lt. Blue/Black: 3 (+) Starter: Green/Red: 4 [3] (-) Hood Input: Gray: 3 [] (+) Siren Output: Brown: 7 6 Black 3 Wh 7 White 8 White 2 Wh Manual/Auto. Transmission Type Prog. Button 6 Green 2 Bk 4 White 4 Red 2 White 2: Brown: (+) 2V 0: Red: (+) 2V 9: Black: (-) Ground 6: Yellow: Ignition F u ses I/P Junction Box (Left Side of Dash Panel) Remote Start Safety Override Switch The Remote Start Safety Override Switch MUST be in the ON position. 4: Yellow/Red: EIPS Alert [2] 3: Brown/Red: (-) Ground [2] 2 & 8: White/Brown: (+) 2V & 7: White: Ignition 2 2 3 (+) 2V: Green, pin [] The siren is optional. [2] This connection is only required when the EIPS (Engine Idle Protection System) feature is activated. [3] The installation of an aftermarket hood pin is only required on vehicles that are not equipped with a factory hood pin. With the exception of the OBDII diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise). 2

6 9 Type 7 Refer to "Vehicle wiring reference charts" on page 6 for more information on vehicle-specific connections. Diagnostic Connector OBDII EMS COM Data: Blue/Orange, pin 5 FT CAN High: Black, pin 5 FT CAN Low: White, pin 6 2 3 4 5 7 8 9 0 2 3 4 5 6 White conn. I/P-M (Back of I/P Junction Box, located left side of dash panel) HS CAN High: White, pin 6 8 HS CAN Low: Red, pin 4 6 2 36 2 3 4 5 6 7 8 9 0 2 3 4 56 7 8 2 3 22 23 24 25 27 28 29 30 3 32 33 34 35 37 38 39 40 4 42 43 44 45 Black or White conn. EM (Driver kick panel) 26 46 [2] (-) Horn: Gray, pin 7 White conn. I/P-K (back of I/P Junction Box, located left side of dash panel) 2 3 4 5 6 7 8 9 0 2 3 4 5 6 7 8 9 20 2 22 23 24 25 26 (-) Driver Door Trigger: Red/Black, pin 6 White conn. M4-L (at Headlight Switch) 2 3 4 5 6 7 8 9 0 2 3 (-) Parking Lights: Blue, pin 2 Black conn. M57 (at Push-to-Start button) White conn. I/P-C (Front of I/P Junction Box, located left side of dash panel.) 2 3 4 5 6 7 8 9 0 2 3 4 5 6 7 8 9 28 20 2 22 23 24 25 26 27 29 30 3 32 33 34 35 36 37 38 (-) PTS: Brown/Black, pin 2 3 4 5 6 7 8 9 0 2 (+) Ignition : Red, pin 28 (+) Ignition 2: White, pin 38 Hood Pin Siren EMS COM Data: Orange/Black: 3 HS CAN Low: Tan: 4 HS CAN High: Tan/Black: 5 FT CAN High: Orange/Green: 7 FT CAN Low: Orange/Brown: 8 (-) Parking Lights: Green/Black: 0 (-) Autolights/RAP Off: White/Violet: (-) Push-to-Start: Lt. Blue/Black: 3 (+) Starter: Green/Red: 4 [3] (-) Hood Input: Gray: 3 [] (+) Siren Output: Brown: 7 6 Black 3 Wh 7 White 8 White 2 Wh Manual/Auto. Transmission Type Prog. Button 6 Green 2 Bk 4 White 4 Red 2 White Remote Start Safety Override Switch 2: Brown: (+) 2V 0: Red: (+) 2V 9: Black: (-) Ground 6: Yellow: Ignition The Remote Start Safety Override Switch MUST be in the ON position. 4: Yellow/Red: EIPS Alert [2] 3: Brown/Red: (-) Ground [2] 2 & 8: White/Brown: (+) 2V & 7: White: Ignition 2 (+) 2V (+) Starter: Green, pin 37 [] The siren is optional. [2] This connection is only required when the EIPS (Engine Idle Protection System) feature is activated. [3] The installation of an aftermarket hood pin is only required on vehicles that are not equipped with a factory hood pin. With the exception of the OBDII diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise). 3

9 Type 8 Refer to "Vehicle wiring reference charts" on page 6 for more information on vehicle-specific connections. Diagnostic Connector OBDII HS CAN High: Green, pin 6 Yellow conn. MC (passenger kick panel) White conn. M20-R (at steering column.) 2 3 4 5 6 7 8 9 0 2 8 6 2 3 4 5 6 8 9 0 2 34 5 6 7 8 9 20 222 23 24 7 [2] (-) Horn: White or Gray, pin 6 HS CAN Low: Orange, pin 4 EMS COM Data: Blue, pin 7 I/P Junction Box (Left Side of Dash Panel) Black Conn. I/P-A (-) PTS: White, pin (-) PTS: White, pin Black Conn. M6 (at Push-to-Start button) Black Conn. M6 (at Push-to-Start button) 2 6 7 3 8 4 5 9 0 Sportage 20-203 OR Sportage 204 2 3 4 5 6 7 8 9 0 2 (+) Ignition 2: Blue or White, pin 3 (+) Starter: Red, pin White conn. M20-L (at Headlight Switch) 2 3 4 5 6 7 8 9 0 2 3 (-) Parking Lights: Blue, pin (+) Ignition : Blue, pin 25 FT CAN Low: Red, pin 52 4 5 6 7 8 9 0 2 2 3 22 23 24 3 4 5 6 7 8 9 20 2 25 30 FT CAN High: Blue, pin 53 27 28 28 29 3 34 35 36 37 38 39 40 4 42 54 32 33 43 44 45 46 47 48 49 50 5 52 53 Hood Pin Siren EMS COM Data: Orange/Black: 3 HS CAN Low: Tan: 4 HS CAN High: Tan/Black: 5 FT CAN High: Orange/Green: 7 FT CAN Low: Orange/Brown: 8 (-) Parking Lights: Green/Black: 0 (-) Push-to-Start: Lt. Blue/Black: 3 (+) Starter: Green/Red: 4 [3] (-) Hood Input: Gray: 3 [] (+) Siren Output: Brown: 7 6 Black 3 Wh 7 White 8 White 2 Wh Manual/Auto. Transmission Type Prog. Button 6 Green 2 Bk 4 White 4 Red 2 White F u ses Remote Start Safety Override Switch 2: Brown: (+) 2V 0: Red: (+) 2V 9: Black: (-) Ground 6: Yellow: Ignition The Remote Start Safety Override Switch MUST be in the ON position. 4: Yellow/Red: EIPS Alert [2] 3: Brown/Red: (-) Ground [2] 2 & 8: White/Brown: (+) 2V & 7: White: Ignition 2 2 3 (+) 2V: Red, pin White conn. I/P-E (Back of I/P Junction box, located left side of dash panel.) : [] The siren is optional. [2] This connection is only required when the EIPS (Engine Idle Protection System) feature is activated. [3] The installation of an aftermarket hood pin is only required on vehicles that are not equipped with a factory hood pin. With the exception of the OBDII diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise). 4

9 9 Type 9 Refer to "Vehicle wiring reference charts" on page 6 for more information on vehicle-specific connections. Blue or Black conn. JM02 (left side of I/P Junction Box, located left side of dash panel.) FT CAN High: Brown, pin 9 Diagnostic Connector OBDII HS CAN High: Red, pin 6 8 6 White conn. EM (Right side of I/P Junction Box, located left side of dash panel) 3 2 4 5 6 3 7 8 9 0 4 5 6 7 8 2 3 9 20 2 22 23 29 30 24 25 26 27 28 32 33 39 40 34 35 36 37 38 4 White conn. MF3 (Driver kick panel) 2 3 4 5 6 7 8 2 3 4 5 6 7 8 9 FT CAN Low: White, pin 9 0 20 HS CAN Low: Blue, pin 4 [2] (-) Horn: Blue, pin 26 EMS COM Data: Blue/Black, pin 36 2 3 4 5 6 7 8 9 0 2 3 4 5 6 7 8 9 20 2 22 23 24 25 26 27 28 29 30 3 32 33 34 35 36 37 38 39 (-) Driver Door Trigger: Green, pin 2 (+) Ignition 2: Red, pin 25 30 27 28 28 29 34 35 36 37 38 39 40 4 42 3 54 32 33 43 44 45 46 47 48 49 50 5 52 53 White conn. M02-L (at Headlight Switch) 2 3 4 5 6 7 8 9 0 2 3 (-) Parking Lights: Pink/Black, pin 2 White conn. M37 (at Push-to-Start button) 4 5 6 7 8 9 0 2 24 2 3 3 4 5 6 7 8 9 20 2 22 23 White conn. I/P-B (Back of I/P Junction Box, located left side of dash panel.) (+) Ignition : Green, pin 25 3 (-) PTS: Pink, pin 2 3 4 5 6 7 8 9 0 2 (+) Starter: White, pin 3 4 5 6 7 8 9 0 2 3 4 5 6 7 8 9 20 2 White conn. I/P-A Siren (Back of I/P Junction Box, located left side of dash panel.) 2 Hood Pin EMS COM Data: Orange/Black: 3 HS CAN Low: Tan: 4 HS CAN High: Tan/Black: 5 FT CAN High: Orange/Green: 7 FT CAN Low: Orange/Brown: 8 (-) Parking Lights: Green/Black: 0 Autolights/RAP Off: White/Violet: (-) Push-to-Start: Lt. Blue/Black: 3 (+) Starter: Green/Red: 4 [3] (-) Hood Input: Gray: 3 [] (+) Siren Output: Brown: 7 6 Black 3 Wh 7 White 8 White 2 Wh Manual/Auto. Transmission Type Prog. Button B la ck co n n. I / P - D (Front of I/P J unction Box, located on left side of dash panel) 6 Green 2 Bk 4 White 4 Red 2 White Remote Start Safety Override Switch 2: Brown: (+) 2V 0: Red: (+) 2V 9: Black: (-) Ground 6: Yellow: Ignition The Remote Start Safety Override Switch MUST be in the ON position. 4: Yellow/Red: EIPS Alert [2] 3: Brown/Red: (-) Ground [2] 2 & 8: White/Brown: (+) 2V & 7: White: Ignition 2 2 (+) 2V: Red, pin [] The siren is optional. [2] This connection is only required when the EIPS (Engine Idle Protection System) feature is activated. [3] The installation of an aftermarket hood pin is only required on vehicles that are not equipped with a factory hood pin. With the exception of the OBDII diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise). 5

Vehicle wiring reference charts Refer to www.directechs.com for more information on any additional connections. Type Wire Information Connector Information Function Color Pin Polarity Name, Location Color No-pins 20 Hyundai Elantra (Smart Key) HS CAN High White 6 Data OBDII, under driver dash Black 6 HS CAN Low Yellow 4 Data OBDII, under driver dash Black 6 FT CAN High White/Orange 3 Data I/P-G, back of I/P Junction box located on left side of dash panel. White 24 FT CAN Low Yellow/Orange Data I/P-G, back of I/P Junction box located on left side of dash panel. White 24 Push-To-Start Yellow/Black (-) At Push-to-Start button. Black 2 Ignition Pink 27 (+) I/P-F, back of I/P Junction box located on left side of dash panel. Black 39 Ignition 2 Orange (+) I/P-F, back of I/P Junction box located on left side of dash panel. Black 39 Starter Yellow 39 (+) I/P-F, back of I/P Junction box located on left side of dash panel. Black 39 Horn White 44 (-) EM in driver kick panel. White 55 EMS COM Data Brown/Orange 0 Data EM in driver kick panel. White 55 Parking Lights Pink or Orange 2 (-) M0-L at multifunction switch located at headlight switch. White 3 (+) 2V Red 2 (+) I/P-D, front of I/P Junction Box (located on left side of dash panel) Black 3 202 Hyundai Elantra (Smart Key) HS CAN High White 6 Data OBDII Diagnostic Connector, under driver dash Black 6 HS CAN Low Yellow 4 Data OBDII Diagnostic Connector, under driver dash Black 6 FT CAN High White/Orange 3 Data I/P-G, back of I/P Junction Box (located on left side of dash panel) White 24 FT CAN Low Yellow/Orange Data I/P-G, back of I/P Junction Box (located on left side of dash panel) White 24 Push-to-Start Yellow/Black (-) M04, at Push-to-Start Button Black 2 Ignition Pink 27 (+) I/P-F, back of I/P Junction Box (located on left side of dash panel) Black 39 Ignition 2 Orange (+) I/P-F, back of I/P Junction Box (located on left side of dash panel) Black 39 Starter Yellow 39 (+) I/P-F, back of I/P Junction Box (located on left side of dash panel) Black 39 Horn White 44 (-) EM, driver kick panel White 55 EMS COM Data Brown/Orange 0 Data EM, driver kick panel White 55 Parking Lights Pink 2 (-) M0-L, at headlight switch White 3 (+) 2V Red 2 (+) I/P-D, front of I/P Junction Box (located on left side of dash panel) Black 3 6

Type Wire Information Connector Information Function Color Pin Polarity Name, Location Color No-pins 203 Hyundai Elantra (Smart Key) (made in US only) HS CAN High White 6 Data OBDII Diagnostic Connector, under driver dash Black 6 HS CAN Low Yellow 4 Data OBDII Diagnostic Connector, under driver dash Black 6 FT CAN High White/Orange 3 Data I/P-G, back of I/P Junction Box (located on left side of dash panel) White 24 FT CAN Low Yellow/Orange Data I/P-G, back of I/P Junction Box (located on left side of dash panel) White 24 Push-to-Start Yellow/Black (-) M04, at Push-to-Start Button Black 2 Ignition Pink 27 (+) I/P-F, back of I/P Junction Box (located on left side of dash panel) Black 39 Ignition 2 Orange (+) I/P-F, back of I/P Junction Box (located on left side of dash panel) Black 39 Starter Yellow 39 (+) I/P-F, back of I/P Junction Box (located on left side of dash panel) Black 39 Horn White 34 (-) EM, driver kick panel White 55 EMS COM Data Brown/Orange 0 Data EM, driver kick panel White 55 Parking Lights Pink 2 (-) M0-L, at headlight switch White 3 (+) 2V Red 2 (+) I/P-D, front of I/P Junction Box (located on left side of dash panel) Black 3 203 Hyundai Elantra (Smart Key) (made in Korea only) & 203-204 Elantra Coupe (Smart Key) HS CAN High White 6 Data OBDII Diagnostic Connector, under driver dash Black 6 HS CAN Low Yellow 4 Data OBDII Diagnostic Connector, under driver dash Black 6 FT CAN High Brown 3 Data I/P-G, back of I/P Junction Box (located on left side of dash panel) White 24 FT CAN Low White Data I/P-G, back of I/P Junction Box (located on left side of dash panel) White 24 Push-to-Start Yellow/Black (-) M04, at Push-to-Start Button Black 2 Ignition Pink 27 (+) I/P-F, back of I/P Junction Box (located on left side of dash panel) Black 39 Ignition 2 Orange (+) I/P-F, back of I/P Junction Box (located on left side of dash panel) Black 39 Starter Yellow 39 (+) I/P-F, back of I/P Junction Box (located on left side of dash panel) Black 39 Horn White 44 (-) EM, driver kick panel White 55 EMS COM Data Brown/Orange 0 Data EM, driver kick panel White 55 Parking Lights Pink 2 (-) M0-L, at headlight switch White 3 (+) 2V Red 2 (+) I/P-D, front of I/P Junction Box (located on left side of dash panel) Black 3 7

Type 2 2 Wire Information Connector Information Function Color Pin Polarity Name, Location Color No-pins 204-205 Hyundai Elantra (Smart Key) HS CAN High White 6 Data OBDII Diagnostic Connector, under driver dash Black 6 HS CAN Low Yellow 4 Data OBDII Diagnostic Connector, under driver dash Black 6 FT CAN High Green 3 Data I/P-G, back of I/P Junction Box (located on left side of dash panel) White 24 FT CAN Low Orange Data I/P-G, back of I/P Junction Box (located on left side of dash panel) White 24 Push-to-Start Yellow/Black (-) M04, at Push-to-Start Button Black 2 Ignition Pink 27 (+) I/P-F, back of I/P Junction Box (located on left side of dash panel) Black 39 Ignition 2 Orange (+) I/P-F, back of I/P Junction Box (located on left side of dash panel) Black 39 Starter Yellow 39 (+) I/P-F, back of I/P Junction Box (located on left side of dash panel) Black 39 Horn White 52 (-) EM, driver kick panel White 58 EMS COM Data Brown/Orange 2 Data EM, driver kick panel White 58 Parking Lights Pink 2 (-) M0-L, at headlight switch White 3 (+) 2V Red 2 (+) I/P-D, front of I/P Junction Box (located on left side of dash panel) Black 3 203-205 Hyundai Elantra GT (Smart Key) HS CAN High White 6 Data OBDII Diagnostic Connector, under driver dash Black 6 HS CAN Low Yellow 4 Data OBDII Diagnostic Connector, under driver dash Black 6 FT CAN High Green 3 Data I/P-G, back of I/P Junction Box (located on left side of dash panel) White 24 FT CAN Low Orange Data I/P-G, back of I/P Junction Box (located on left side of dash panel) White 24 Push-to-Start Yellow/Black (-) M04, at Push-to-Start Button Black 2 Ignition White 27 (+) I/P-F, back of I/P Junction Box (located on left side of dash panel) Black 39 Ignition 2 Orange (+) I/P-F, back of I/P Junction Box (located on left side of dash panel) Black 39 Starter Yellow 39 (+) I/P-F, back of I/P Junction Box (located on left side of dash panel) Black 39 Horn White 4 (-) EM, driver kick panel White 58 EMS COM Data Blue/Black 2 Data EM, driver kick panel White 58 Parking Lights Pink 2 (-) M0-L, at headlight switch White 3 (+) 2V Red 2 (+) I/P-D, front of I/P Junction Box (located on left side of dash panel) Black 3 8

Type 3 3 Wire Information Connector Information Function Color Pin Polarity Name, Location Color No-pins 202-203 Hyundai Veloster (Smart Key) HS CAN High White 6 Data OBDII Diagnostic Connector, under driver dash Black 6 HS CAN Low Yellow 4 Data OBDII Diagnostic Connector, under driver dash Black 6 FT CAN High White/Orange 5 Data I/P-C, back of I/P Junction Box (located on left side of dash panel) White 24 FT CAN Low Yellow/Orange 6 Data I/P-C, back of I/P Junction Box (located on left side of dash panel) White 24 Push-to-Start Yellow/Black (-) M04, at Push-to-Start Button White 2 Ignition Pink 7 (+) I/P-F, at I/P Junction Box (located on left side of dash panel) White 6 Ignition 2 Red 4 (+) I/P-F, at I/P Junction Box (located on left side of dash panel) White 6 Starter Yellow 5 (+) I/P-F, at I/P Junction Box (located on left side of dash panel) White 6 Horn White/Orange 44 (-) EM, driver kick panel White 55 EMS COM Data Blue 0 Data EM, driver kick panel White 55 Parking Lights Pink (-) I/P-C, back of I/P Junction Box (located on left side of dash panel) White 24 (+) 2V Red 2 (+) I/P-L, front of I/P Junction Box (located on left side of dash panel) White 4 Driver Door Trigger Brown 7 (-) MF, at driver kick panel White 56 204 (early 204) Hyundai Veloster (Smart Key) HS CAN High White 6 Data OBDII Diagnostic Connector, under driver dash Black 6 HS CAN Low Yellow 4 Data OBDII Diagnostic Connector, under driver dash Black 6 FT CAN High White/Orange 5 Data I/P-C, back of I/P Junction Box (located on left side of dash panel) White 24 FT CAN Low Yellow/Orange 6 Data I/P-C, back of I/P Junction Box (located on left side of dash panel) White 24 Push-to-Start Yellow/Black (-) M04, at Push-to-Start Button White 2 Ignition Pink 7 (+) I/P-F, at I/P Junction Box (located on left side of dash panel) White 6 Ignition 2 Red 4 (+) I/P-F, at I/P Junction Box (located on left side of dash panel) White 6 Starter Yellow 5 (+) I/P-F, at I/P Junction Box (located on left side of dash panel) White 6 Horn White/Orange 44 (-) EM, driver kick panel White 55 EMS COM Data Blue 0 Data EM, driver kick panel White 55 Parking Lights Pink (-) I/P-C, back of I/P Junction Box (located on left side of dash panel) White 24 (+) 2V Red 2 (+) I/P-L, front of I/P Junction Box (located on left side of dash panel) White 4 Driver Door Trigger Brown 7 (-) MF, at driver kick panel White 56 9

Type 3 4 Wire Information Connector Information Function Color Pin Polarity Name, Location Color No-pins 204 (late 204) - 205 Hyundai Veloster (Smart Key) HS CAN High White 6 Data OBDII Diagnostic Connector, under driver dash Black 6 HS CAN Low Yellow 4 Data OBDII Diagnostic Connector, under driver dash Black 6 FT CAN High White/Orange 5 Data I/P-C, back of I/P Junction Box (located on left side of dash panel) White 24 FT CAN Low Yellow/Orange 6 Data I/P-C, back of I/P Junction Box (located on left side of dash panel) White 24 Push-to-Start Yellow/Black (-) M04, at Push-to-Start Button White 2 Ignition Pink 7 (+) I/P-F, at I/P Junction Box (located on left side of dash panel) White 6 Ignition 2 Red 4 (+) I/P-F, at I/P Junction Box (located on left side of dash panel) White 6 Starter Yellow 5 (+) I/P-F, at I/P Junction Box (located on left side of dash panel) White 6 Horn White/Orange 44 (-) EM, driver kick panel Black 60 EMS COM Data Blue 6 Data EM, driver kick panel Black 60 Parking Lights Pink (-) I/P-C, back of I/P Junction Box (located on left side of dash panel) White 24 (+) 2V Red 2 (+) I/P-L, front of I/P Junction Box (located on left side of dash panel) White 4 Driver Door Trigger Brown 7 (-) MF, at driver kick panel White 56 20-203 Kia Optima (Smart Key) HS CAN High White 6 Data OBDII Diagnostic Connector, under driver dash Black 6 HS CAN Low Yellow 4 Data OBDII Diagnostic Connector, under driver dash Black 6 FT CAN High White/Orange 25 Data I/P-E, back of I/P Junction Box (located on left side of dash panel) Black 39 FT CAN Low Yellow/Orange 38 Data I/P-E, back of I/P Junction Box (located on left side of dash panel) Black 39 Push-to-Start Yellow/Black (-) M04, at Push-to-Start Button Black 0 Ignition Pink (+) I/P-E, back of I/P Junction Box (located on left side of dash panel) Black 39 Ignition 2 Orange 4 (+) I/P-E, back of I/P Junction Box (located on left side of dash panel) Black 39 Starter Orange 26 (+) I/P-E, back of I/P Junction Box (located on left side of dash panel) Black 39 Horn White 42 (-) EM, driver kick panel White 43 EMS COM Data Brown/Orange 0 Data EM, driver kick panel White 43 Parking Lights Pink (-) M0-L, at headlight switch White 3 (+) 2V Pink (+) I/P-C, front of I/P Junction Box (located on left side of dash panel) Black 3 20

Type 4 5 Wire Information Connector Information Function Color Pin Polarity Name, Location Color No-pins 20-204 Kia Optima Hybrid (Smart Key) HS CAN High White 6 Data OBDII Diagnostic Connector, under driver dash Black 6 HS CAN Low Yellow 4 Data OBDII Diagnostic Connector, under driver dash Black 6 FT CAN High White/Orange 25 Data I/P-E, back of I/P Junction Box (located on left side of dash panel) Black 39 FT CAN Low Yellow/Orange 38 Data I/P-E, back of I/P Junction Box (located on left side of dash panel) Black 39 Push-to-Start Yellow/Black (-) M04, at Push-to-Start Button Black 0 Ignition Pink (+) I/P-E, back of I/P Junction Box (located on left side of dash panel) Black 39 Ignition 2 Orange 4 (+) I/P-E, back of I/P Junction Box (located on left side of dash panel) Black 39 Starter Yellow 26 (+) I/P-E, back of I/P Junction Box (located on left side of dash panel) Black 39 Horn White 42 (-) EM, driver kick panel White 43 EMS COM Data Blue 0 Data EM, driver kick panel White 43 Parking Lights Pink (-) M0-L, at headlight switch White 3 (+) 2V Pink (+) I/P-C, front of I/P Junction Box (located on left side of dash panel) Black 3 204-205 Kia Optima (Smart Key) HS CAN High White 6 Data OBDII Diagnostic Connector, under driver dash Black 6 HS CAN Low Yellow 4 Data OBDII Diagnostic Connector, under driver dash Black 6 FT CAN High White/Orange 3 Data I/P-G, back of I/P Junction Box (located on left side of dash panel) White 24 FT CAN Low Yellow/Orange Data I/P-G, back of I/P Junction Box (located on left side of dash panel) White 24 Push-to-Start Yellow/Black (-) M04, at Push-to-Start Button Black 2 Ignition Pink (+) I/P-E, back of I/P Junction Box (located on left side of dash panel) Black 39 Ignition 2 Black/Orange 2 (+) EM, driver kick panel White 58 Starter Gray 9 (+) EM, driver kick panel White 58 Horn White 39 (-) EM, driver kick panel White 58 EMS COM Data Brown/Orange 4 Data EM, driver kick panel White 58 Parking Lights Pink (-) M0-L, at headlight switch White 3 (+) 2V Red (+) I/P-C, front of I/P Junction Box (located on left side of dash panel) Black 3 2

Type 5 6 Wire Information Connector Information Function Color Pin Polarity Name, Location Color No-pins 204 Kia Optima Hybrid (Smart Key) HS CAN High White 6 Data OBDII Diagnostic Connector, under driver dash Black 6 HS CAN Low Yellow 4 Data OBDII Diagnostic Connector, under driver dash Black 6 FT CAN High White/Orange 3 Data I/P-G, back of I/P Junction Box (located on left side of dash panel) White 24 FT CAN Low Yellow/Orange Data I/P-G, back of I/P Junction Box (located on left side of dash panel) White 24 Push-to-Start Yellow/Black (-) M04, at Push-to-Start Button Black 2 Ignition Pink (+) I/P-E, back of I/P Junction Box (located on left side of dash panel) Black 39 Ignition 2 Black/Orange 9 (+) EM, driver kick panel White 58 Starter Gray 9 (+) EM, driver kick panel White 58 Horn White 39 (-) EM, driver kick panel White 58 EMS COM Data Blue 4 Data EM, driver kick panel White 58 Parking Lights Pink (-) M0-L, at headlight switch White 3 (+) 2V Red (+) I/P-C, front of I/P Junction Box (located on left side of dash panel) Black 3 204-205 Kia Rondo (Smart Key) HS CAN High White 6 Data OBDII Diagnostic Connector, under driver dash Black 6 HS CAN Low Brown 4 Data OBDII Diagnostic Connector, under driver dash Black 6 FT CAN High Orange 3 Data I/P-G, back of I/P Junction Box (located on left side of dash panel) White 24 FT CAN Low Blue Data I/P-G, back of I/P Junction Box (located on left side of dash panel) White 24 Push-to-Start Yellow/Black (-) M04, at Push-to-Start Button White 2 Ignition Pink 58 (+) EM, driver kick panel White 58 Ignition 2 White 32 (+) EM, driver kick panel White 58 Starter Green 49 (+) EM, driver kick panel White 58 Horn White 7 (-) EM, driver kick panel White EMS COM Data Blue/Orange 37 Data EM, driver kick panel White 58 Parking Lights Pink 4 (-) M0-L, at headlight switch White 58 (+) 2V Green (+) Back of I/P Junction Box (located on left side of dash panel) Black 6 22

Type 7 8 Wire Information Connector Information Function Color Pin Polarity Name, Location Color No-pins 204-205 Kia Sorento (Smart Key) HS CAN High White 6 Data OBDII Diagnostic Connector, under driver dash Black 6 HS CAN Low Red 4 Data OBDII Diagnostic Connector, under driver dash Black 6 FT CAN High Black 5 Data I/P-M, back of I/P Junction Box (located on left side of dash panel) White 6 FT CAN Low White 6 Data I/P-M, back of I/P Junction Box (located on left side of dash panel) White 6 Push-to-Start Brown/Black (-) M57, at Push-to-Start Button Black 2 Ignition Red 28 (+) I/P-C, front of I/P Junction Box (located on left side of dash panel) White 38 Ignition 2 White 38 (+) I/P-C, front of I/P Junction Box (located on left side of dash panel) White 38 Starter Green 37 (+) I/P-C, front of I/P Junction Box (located on left side of dash panel) White 38 Horn Gray 7 (-) EM, driver kick panel Black or White 46 EMS COM Data Blue/Orange 5 Data EM, driver kick panel Black or White 46 Parking Lights Blue 2 (-) M4-L, at headlight switch White 3 (+) 2V Red (+) I/P-B, front of I/P Junction Box (located on left side of dash panel) White 36 Driver Door Trigger Red/Black 6 (-) I/P-K, front of I/P Junction Box (located on left side of dash panel) White 26 20 (2,4L) Kia Sportage (Smart Key) HS CAN High Green 6 Data OBDII Diagnostic Connector, under driver dash Black 6 HS CAN Low Orange 4 Data OBDII Diagnostic Connector, under driver dash Black 6 FT CAN High Blue 53 Data I/P-E, back of I/P Junction Box (located on left side of dash panel) White 54 FT CAN Low Red 52 Data I/P-E, back of I/P Junction Box (located on left side of dash panel) White 54 Push-to-Start White (-) M6, at Push-to-Start Button Black 0 Ignition Blue 25 (+) I/P-E, back of I/P Junction Box (located on left side of dash panel) White 54 Ignition 2 Blue 3 (+) I/P-E, back of I/P Junction Box (located on left side of dash panel) White 54 Starter Red (+) I/P-E, back of I/P Junction Box (located on left side of dash panel) White 54 Horn Gray 6 (-) M20-R, at steering column White 2 EMS COM Data Blue 7 Data MC, passenger kick panel Yellow 24 Parking Lights Blue (-) M20-L, at headlight switch White 3 (+) 2V Red (+) I/P-A, front of I/P Junction Box (located on left side of dash panel) Black 3 23

Type 8 8 Wire Information Connector Information Function Color Pin Polarity Name, Location Color No-pins 202-203 (2,0L) Kia Sportage (Smart Key) HS CAN High Green 6 Data OBDII Diagnostic Connector, under driver dash Black 6 HS CAN Low Orange 4 Data OBDII Diagnostic Connector, under driver dash Black 6 FT CAN High Blue 53 Data I/P-E, back of I/P Junction Box (located on left side of dash panel) White 54 FT CAN Low Red 52 Data I/P-E, back of I/P Junction Box (located on left side of dash panel) White 54 Push-to-Start White (-) M6, at Push-to-Start Button Black 0 Ignition Blue 25 (+) I/P-E, back of I/P Junction Box (located on left side of dash panel) White 54 Ignition 2 Blue 3 (+) I/P-E, back of I/P Junction Box (located on left side of dash panel) White 54 Starter Red (+) I/P-E, back of I/P Junction Box (located on left side of dash panel) White 54 Horn White 6 (-) M20-R, at steering column White 2 EMS COM Data Blue 7 Data MC, passenger kick panel Yellow 24 Parking Lights Blue (-) M20-L, at headlight switch White 3 (+) 2V Red (+) I/P-A, front of I/P Junction Box (located on left side of dash panel) Black 3 204-205 Kia Sportage (Smart Key) HS CAN High Green 6 Data OBDII Diagnostic Connector, under driver dash Black 6 HS CAN Low Orange 4 Data OBDII Diagnostic Connector, under driver dash Black 6 FT CAN High Blue 53 Data I/P-E, back of I/P Junction Box (located on left side of dash panel) White 54 FT CAN Low Red 52 Data I/P-E, back of I/P Junction Box (located on left side of dash panel) White 54 Push-to-Start White (-) M6, at Push-to-Start Button Black 2 Ignition Blue 25 (+) I/P-E, back of I/P Junction Box (located on left side of dash panel) White 54 Ignition 2 Blue or White 3 (+) I/P-E, back of I/P Junction Box (located on left side of dash panel) White 54 Starter Red (+) I/P-E, back of I/P Junction Box (located on left side of dash panel) White 54 Horn White 6 (-) M20-R, at steering column White 2 EMS COM Data Blue 7 Data MC, passenger kick panel Yellow 24 Parking Lights Blue (-) M20-L, at headlight switch White 3 (+) 2V Red (+) I/P-A, front of I/P Junction Box (located on left side of dash panel) Black 3 24