Update Alert: Firmware updates are posted to the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide XK01-AMDL controls primary Original Equipment (OE) door lock and factory alarm functions on select Buick, Cadillac, Chevrolet, Chrysler, Dodge, GMC, Hummer, Isuzu, Jeep, Oldsmobile, Pontiac Saab vehicles. It also provides data override on all GM Passlock II and Passkey3 type (J1850) immobilizer systems. Index Vehicle Application Guide... 02 Installation Type A... Type B... Type C... 03 04 05 Wiring Connection Reference Chart... 06 Programming Vehicle Type Programming...... 07 User Settings - Optional Programming... 08 Option List... 08 Door Detection Notes... 09 LED Diagnostics and Troubleshooting... 09 Warranty... 10 Buick, Cadillac, Chevrolet, Chrysler, Dodge, GMC, Hummer, Isuzu, Jeep, Oldsmobile, Pontiac Saab are registered trademarks and property of their respective companies.
Page 2 Vehicle Application Guide ST-Ignition Status SS-Entry Monitoring Trunk/Hatch Pin SS-Entry Monitoring Front Door Pins SS-Entry Monitoring Driver Door Pin SS-Entry Monitoring ALL Door Pins SS-CAN Alarm control w/ FOB remote RS-Tach / RPM Output RS-RAP Shut Down (Remote ACC Power) PK-Immobilizer Bypass- Data No Key Req'd DL-Trunk / Hatch Release DL-Sliding Door Control Passenger DL-Sliding Door Control Driver DL-Fuel Door Release DL-Driver Priority Unlock DL-Door Unlock DL-Door Lock Control DL-Disarm Factory Security DL-Arm Factory Security CC-Rear Window **** Defogger Activation CC-Radio Channel Memory CC-Power Windows Rollup CC-Power Seat Memory CC-Power Mirror Memory **** CC-Heated Seats Activation CC-Heated Mirrors AV-Panic Mode Activation Vehicles 1997 1998 1999 2000 2001 2002 2003 2004 2005 2006 2007 2008 2009 Buick LeSabre 2 2 2 2 2 2 D D D D Park Avenue 3 3 3 3 3 3 3 3 3 D D D D Rainier 1** 1** 1** 1** 1** D D D D Ultra 3 3 3 3 3 3 3 3 3 D D D D Cadillac 09 08 07 06 05 04 03 02 01 00 99 98 97 CTS 2 2 2 2 2 D D D D DeVille 2 2 2 2 2 2 2 2 D D D D Escalade 4 4 4 4 D D D D Seville SLS 3 3 3 3 2 2 2 D D D D Seville STS 3 3 3 3 2 2 2 D D D D SRX 2 2 2 2 D D D D Chevrolet 09 08 07 06 05 04 03 02 01 00 99 98 97 Avalanche 4** 4** 4** 4** D D D D CK Pickup 4** 4** 4** 4** D D D D Impala 2* 2* 2* 2* 2* 2* D D D D Monte Carlo 2* 2* 2* 2* 2* 2* D D D D Silverado 4** 4** 4** 4** D D D D Silverado Classic 4** D D D D SSR 1** 1** 1** 1** D D D D Suburban 4*** 4*** 4*** 4*** D D D D Tahoe 4*** 4*** 4*** 4*** D D D D TrailBlazer 1** 1** 1** 1** 1** 1** 1** 1** D D D D TrailBlazer EXT 1** 1** 1** 1** D D D D Chrysler 09 08 07 06 05 04 03 02 01 00 99 98 97 Pacifica 6 6 6 6 6 6 D D D Town Country 7 7 7 7 D D D Dodge 09 08 07 06 05 04 03 02 01 00 99 98 97 Caravan 7 7 7 7 D D D Grand Caravan 7 7 7 7 D D D GMC 09 08 07 06 05 04 03 02 01 00 99 98 97 Envoy 1** 1** 1** 1** 1** 1** 1** 1** D D D D Envoy XL 1** 1** 1** 1** 1** D D D D Sierra 4** 4** 4** 4** D D D D Sierra Classic 4** D D D D Suburban 4*** 4*** 4*** 4*** D D D D Yukon 4*** 4*** 4*** 4*** D D D D Yukon XL 4*** 4*** 4*** 4*** D D D D Hummer 09 08 07 06 05 04 03 02 01 00 99 98 97 H2 4*** 4*** 4*** 4*** 4*** D D D D Isuzu 09 08 07 06 05 04 03 02 01 00 99 98 97 Ascender 1** 1** 1** 1** 1** 1** D D D D Jeep 09 08 07 06 05 04 03 02 01 00 99 98 97 Grand Cherokee 5 5 5 5 5 5 D D D Grand Cherokee Limited 5 5 5 5 5 5 D D D Liberty 7 7 7 D D D Oldsmobile 09 08 07 06 05 04 03 02 01 00 99 98 97 Alero w/ FOB only 2* 2* 2* 2* 2* 2* D D D D Aurora 2 2 2 D D D D Bravada 1** 1** 1** D D D D Pontiac 09 08 07 06 05 04 03 02 01 00 99 98 97 Bonneville 2 2 2 2 2 2 D D D D Grand Am w/ FOB only 2* 2* 2* 2* 2* 2* 2* D D D D Saab 09 08 07 06 05 04 03 02 01 00 99 98 97 9-7X 1** 1** 1** 1** 1** D D D D * In some vehicles, XK01-AMDL may only bypass the Passlock II via data. Once programmed, test the door lock inputs to determine if the XK01-AMDL will activate these functions via DATA. If there is no activation, then the door lock system will need to be controlled analog via the remote starter. ** In these vehicles, rear doors are not detected on the data bus, use the rear doors pins instead. *** In these vehicles, rear doors and hatch are not detected on the data bus, use rear doors and hatch pin at the BCM instead. **** Defogger and Heated seats features may or may not function depending on the capabilities of the vehicle. ST: Function/Feature D: Data-to-Data (D2D) only AV: Horn Lights Controls DL: OE Door Lock Alarm Controls RS: Engine Start Status SS: Integrated Security Monitoring PK: Transponder Immobilizer Override CC: Comfort Convenience Controls : D2D and W2W
Installation Type A Wiring diagram for types 1 to 4. See the Vehicle Application Guide on page 2 for more information. Page 3 (+) 12 V Input Parking Lights (+) Start (+) Ignition 1 (+) Ignition 2 (+) Accessory (-) Neutral Safety (DEI Platforms Only) Starter Remote (-) Trunk or Disarm Output** (-) Aux 1 Fuel Door Output** (-) Door Sense Trigger Input* (-) Unlock Output (-) Lock Output (-) GWR (status) Output Option A: Firmware upgrades (XKD2D65). Option B: Range Extender connection (HARD2D Rev. 3). Option C: Plug D2D harness directly into remote starter. TX RX (+) 12 V To Brown Accessory wire in vehicle 85 87 86 87a 30 (+) 12 V Relay wiring for windows roll-up option (required for type 4 only) XK01 4 10 1: (+) 12 V 2: RX 3: 4: TX 1: Brown: (-) GWR (status) Input 2: Green: (-) Lock Input 3: Blue: (-) Unlock Input 4: Violet/White: (-) Door Sense Trigger Output* 5: Violet: Data 6: Pink/White: (-) Aux 2 Output** 7: Pink: (-) Aux 1 Fuel Door Input** 8: Orange: (-) Trunk or Disarm Input** 9: Red: (+) 12 V Input 10: Black: (-) Chassis Ground Programming Button +12VDC Pin 2 1 8 9 16 OBII (Diagnostic connector) Face view, under dash, driver side Not required in D2D mode. * For types 1 4, rear doors and tail gate (type 4 only) are not detected on the data bus. Use the door trigger at the BCM to detect these entries. ** See Vehicle Wiring Connection Reference Chart on page 6.
Installation Type B Wiring diagram for type 5. See the Vehicle Application Guide on page 2 for more information. Page 4 (+) 12 V Input Parking Lights (+) Start (+) Ignition (+) Accessory 1 (+) Accessory 2 (-) Neutral Safety (DEI Platforms Only) Starter Remote (-) Disarm Output* (-) Door Sense Trigger Input (-) Unlock Output (-) Lock Output (-) GWR (status) Output Option A: Firmware upgrades (XKD2D65). Option B: Range Extender connection (HARD2D Rev. 3). Option C: Plug D2D harness directly into remote starter. TX RX (+) 12 V XK01 4 10 1: (+) 12 V 2: RX 3: 4: TX 1: Brown: (-) GWR (status) Input 2: Green: (-) Lock Input 3: Blue: (-) Unlock Input 4: Violet/White: (-) Door Sense Trigger Output 5: Violet: Data 8: Orange: (-) Disarm Input* 9: Red: (+) 12 V Input 10: Black: (-) Chassis Ground Programming Button +12VDC Pin 2 1 8 9 16 OBII (Diagnostic connector) Face view, under dash, driver side Not required in D2D mode. * See Vehicle Wiring Connection Reference Chart on page 6.
Installation Type C Wiring diagram for types 6 and 7. See the Vehicle Application Guide on page 2 for more information. Page 5 (+) 12 V Input Parking Lights (+) Start (+) Ignition (+) Accessory (-) Neutral Safety (DEI Platforms Only) Starter Remote (-) Trunk Output* (-) Aux 1 Right Sliding Door Output* (-) Aux 2 Left Sliding Door Output* (-) Door Sense Trigger Input (-) Unlock Output (-) Lock Output (-) GWR (status) Output Option A: Firmware upgrades (XKD2D65). Option B: Range Extender connection (HARD2D Rev. 3). Option C: Plug D2D harness directly into remote starter. TX RX (+) 12 V XK01 4 10 1: (+) 12 V 2: RX 3: 4: TX 1: Brown: (-) GWR (status) Input 2: Green: (-) Lock Input 3: Blue: (-) Unlock Input 4: Violet/White: (-) Door Sense Trigger Output 5: Violet: Data 6: Pink/White: (-) Aux 2 Left Sliding Door Input* 7: Pink: (-) Aux 1 Right Sliding Door Input* 8: Orange: (-) Trunk Input* 9: Red: (+) 12 V Input 10: Black: (-) Chassis Ground Programming Button +12VDC Pin 2 1 8 9 16 OBII (Diagnostic connector) Face view, under dash, driver side Not required in D2D mode. * See Vehicle Wiring Connection Reference Chart on page 6.
Page 6 Wiring Connection Reference Chart Pin Wire Color Vehicle Type D2D/W2W I/O Status (-)/(+) 1 Brown 2 Green Connector Location 1 to 4 D2D/W2W Input (-) RCS Ground When Running Output of RCS. 5 to 7 D2D/W2W Input (-) RCS Ground When Running Output of RCS. 1 to 5 D2D/W2W Input (-) RCS Lock Output wire of RCS. Specific Wire Connector Location Activation and/or Functionality OEM security arm/disarm + Immobilizer Bypass (defrost + heated seats at 32ºF (0ºC) for GM vehicles only). OEM security arm/disarm (defrost + heated seats at 32ºF (0ºC) for GM vehicles only). Locks all doors arms OE security. Window roll-up feature, activated with 2nd press of aftermarket remote (see User Settings, Mode 5) for GM Jeep vehicles only. 6 and 7 D2D/W2W Input (-) RCS Lock Output wire of RCS. Locks all doors arms OE security. 3 Blue All Types D2D/W2W Input (-) RCS Unlock Output wire of RCS. Unlocks all doors (see User Settings, Mode 1). Door trunk/hatc h Sense Trigger Input wire of Detects door trunk status Open/Close via Data 4 Violet/White All Types D2D/W2W Output (-) RCS RCS. Bus; then converts to an analog output. On-board Diagno stic Connector (OBDII) pin 2, 5 Violet All Types Data Vehicle Data communication with the vehicle. violet wire. 1, 2, 3, 5, 6 N/C N/C N/C N/C N/C N/C 6 Pink/Whit 7 Pink e 4 W2W Output (-) Vehicle Vehicle's brown Accessory wire (relay required). Window roll-up feature (relay required). 7 D2D/W2W Input (-) RCS Aux 2 Output of RCS. 2 D2D/W2W Input (-) RCS Aux 1 Output of RCS. Opens fuel door. 7 D2D/W2W Input (-) RCS Aux 1 Output of RCS. 1, 3, 4, 5, 6 N/C N/C N/C N/C N/C N/C 1 sec. (-) Pulse left sliding door Open/Close (see User Settings, Mode 2). 1 sec. (-) Pulse right sliding door Open/Close (see User Settings, Mode 2). 8 Orange 1, 4, 5 D2D/W2W Input (-) RCS Disarm Output of RCS. Connect if vehicle does not disarm upon remote start. 2, 3, 6, 7 D2D/W2W Input (-) RCS Trunk Release Output of RCS. Trunk release. 9 Red All Types D2D/W2W Input ( +) Vehicle Constant (+) 12 Volt Source. Power source. 10 Black All Types D2D/W2W Input (-) Vehicle Chassis Ground. Ground source. Legend: RCS = Remote Control System; W2W = Analogue Wire-to-Wire; D2D = Data-to-Data
Vehicle Type Programming Page 7 The interface kit is designed to operate on any one of 7 possible vehicle types. Once the 10-pin harness wires have been connected, the next step is to program the interface module to operate on the appropriate vehicle type. Refer to the Vehicle Application Guide on page 2 for more information on types. In W2W: Connect the 10-pin harness to the module. The LED will turn ON solid. 1 1 10-pin Solid Red In D2D: Connect the 10-pin harness, and then the D2D harness to the module. The LED will turn ON solid. 10-pin + D2D Solid Red 2 Insert the key into the ignition barrel and turn it to the ON position. The LED will turn OFF*, and then it will begin a flashing pattern that corresponds to the vehicle type selection. (The default vehicle type selection is 1.) *If the module has already been programmed to the vehicle, the LED will flash 4 times, in which case, skip to step 4. OFF ON START Key at ON Off Flashes 3 To change the vehicle type, press and release the Programming button until the LED flash pattern corresponds to the selected vehicle type. The LED flash pattern will match the selected vehicle type. For example: - 1 flash = Type 1-2 flashes = Type 2 Press Release Flashes 4 To save the vehicle type selection, press and hold the Programming button until the LED flashes rapidly*. * For GM vehicles (types 1 to 4), the LED will not flash; it will stay ON solid. You will need to use the key and start the vehicle to turn the LED OFF and complete the programming sequence. Press Hold Flashes The module is now programmed.
User Settings - Optional Programming Page 8 User modes are identified by a slow LED flashing pattern: 1 slow flash = Mode 1; 2 slow flashes = Mode 2, etc. 1 2 3 4 Turn the key to the OFF position, but leave it in the ignition barrel. To access User Modes: Press and hold the Programming button until the LED flashes rapidly, and then release the button. To select a Mode: Press and release the Programming button until the slow flashing pattern of the LED corresponds to the required Mode selection. For example: - 1 slow flash = Mode 1-2 slow flashes = Mode 2 To change the Mode Option: Press the LOCK or UNLOCK button the aftermarket transmitter until the quick flashing of the LED corresponds to the required Mode Option selection. For example: - 1 quick flash = Option 1-2 quick flashes = Option 2 Press Hold Press Release ( Flashes or Press OFF ON START Key at OFF Release ( Flashes Slowly Flashes Quickly To save and exit: 5 Press and hold the Programming button until the LED flashes once. Press Hold Flashes x1 Option List Mode Option 1 2 3 4 5 8 * Default value. Description 1* 1st pulse - Unlock all doors. 2 1st pulse - Unlock driver door; 2nd pulse - Unlock all doors. 1* (Aux 1) Pink wire negative. 2 N/A 1* (Aux 2) Pink/White wire negative. 2 N/A 1* (Aux 2) Pink/White wire output (Type 4 only). 2 (Aux 2) Pink/White wire input. 1* Windows roll-up OFF. 2 Windows roll-up ON. 1* N/A 2 Reset mode with Unlock button.
Door Detection Notes Page 9 The module detects all door triggers through the data line. When it detects an open door, it sends a negative (-) pulse trigger on the Purple/White wire (Door Trigger Output). For vehicles in types 1 and 4, the front doors and rear hatch are ONLY monitored via the data line. However, the rear doors are triggered separately and are not monitored via the data line. These wires are usually found at the BCM (Body Control Module) or at the rear doors. LED Diagnostics and Troubleshooting LED Status Description Troubleshooting During Power Up Off Solid red Vehicle Type Programming x4 Off, then flashes Flashes x4 Flashes rapidly Solid red Module has no power. Module has power (the 10-pin harness was connected). Flashing pattern that corresponds to the vehicle type selection. Module has already been programmed to this vehicle. Vehicle type selection has been saved. Vehicle type selection has been saved. Make sure the D2D harness is connected or the 12V is present between the red and black wires. Skip to step 4 of the Vehicle Type Programming procedure to save the selection. User Settings - Optional Programming Flashes rapidly To access User Modes. Slow flashing pattern Flashing pattern that corresponds to the mode selection. Quick flashing Flashing pattern that corresponds to pattern the option selection. x1 Flashes once User Settings have been saved and programming exited. Normal Operation Solid red GWR is now active. x1 Flashes once An input trigger was detected on the module. In step 4 of the Vehicle Type Programming: on GM vehicles (types 1 to 4), the LED will not flash; it will stay solid red. You will need to use the key and start the vehicle to turn the LED off and complete the programming sequence.
Limited One Year Consumer Warranty Page 10 For a period of ONE YEAR from the date of purchase of a Directed Electronics remote start or security product, Directed Electronics. ( DIRECTED ) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, the security or remote start accessory piece (hereinafter the Part ), which proves to be defective in workmanship or material under normal use, provided the following conditions are met: the Part was purchased from an authorized DIRECTED dealer; and the Part is returned to DIRECTED, postage prepaid, along with a clear, legible copy of the receipt or bill of sale bearing the following information: consumer s name, address, telephone number, the authorized licensed dealer s name and complete product and Part description. This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to its intended purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defect in materials or construction. TO THE MAXIMUM EXTENT ALLOWED BY LAW, EXCEPT AS STATED ABOVE, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NONINFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING DEALERS OR INSTALLERS. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER S PURCHASE PRICE OF THE PART. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR AT DIRECTED S OPTION THE PART AS DESCRIBED ABOVE. Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights and you may also have other rights that vary from State to State. DIRECTED does not and has not authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this Part. 920-0007 2009-09 This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the select vehicle list upon completion of compatibility testing. Visit website for latest vehicle application guide. DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for any consequential damages sustained in connection with the part(s) installation. The manufacturer and it s distributors will not, nor will they authorize any representative or any other individual to assume obligation or liability in relation to the interface kit / data bus interface part(s) other than its replacement. N.B.: Under no circumstances shall the manufacturer and distributors of this product be liable for consequential damages sustained in connection with this product and neither assumes nor authorizes any representative or other person to assume for it any obligation or liability other than the replacement of this product only. Protected by U.S. Patents: 5,719,551; 6,011,460 B1 *; 6,243,004 B1; 6,249,216 B1; 6,275,147 B1; 6,297,731 B1; 6,346,876 B1; 6,392,534 B1; 6,529,124 B2; 6,696,927 B2; 6,756,885 B1; 6,756,886 B2; 6,771,167 B1; 6,812,829 B1; 6,924,750 B1; 7,010,402 B1; 7,015,830 B1; 7,031,826 B1; 7,046,126 B1; 7,061,137 B1; 7,068,153 B1; 7,205,679 B1; Cdn. Patent: 2,320,248; 2,414,991; 2,415,011; 2,415,023; 2,415,027; 2,415,038; 2,415,041; 2,420,947; 2,426,670; 2,454,089; European Patent: 1,053,128; Pat. Pending: 2,291,306. Made in Canada. Additional information can be found at: www.xpresskit.com www.directechs.com