This module can only be flashed and configured using XpressVIP at or using the Directechs

Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide The NISS08 firmware for DBALL is an all-in-one door lock and override module compatible with specific Infiniti and Nissan vehicles. This guide supports the installation of a DBALL in Remote Start Ready (RSR) mode. This solution offers three () configuration options to control your system: x OEM Lock Remote Start Activation, RF System or SmartStart (all sold separately). This module can only be flashed and configured using XpressVIP at www.directechs.com or using the Directechs Mobile application for smartphones. Refer to the Module Programming section on page for more information. Remote Start Ready (RSR) is a function that enables the interface module to remote start the vehicle completely on its own. Consequently, there is no need for an aftermarket or an OEM remote starter in order to start the vehicle from a distance. Important! This product is NOT compatible with vehicles equipped with a manual transmission. -This guide is compatible with the NISS08 firmware version.5 and higher. - Security light will flash during runtime and turn on solid during takeover procedure. - Power door locks will not operate properly if doors are open. Index Vehicle Application Guide... 0 Installation (Wiring Diagrams & Vehicle Wiring Reference Charts) Type... Type... Type... Type... SmartStart/XL0 Installation Notes... Programming Module Programming... Module Reset... Hard Reset... Feature & Option List... Feature Programming... 0 05 07 09 LED Diagnostics & Troubleshooting... Parking Light Error Codes... Limited One-Year Consumer Warranty... 5 7 8 Quick Reference Guide... SmartStart Compatible SmartStart is equipped with DD, which means it can be connected to an interface module and used in Remote Start Ready (RSR) mode without the use of a remote starter. See the Module Programming section for more information. Infiniti and Nissan are registered trademarks and property of their respective companies. 9

Vehicle Application Guide Page The following table lists the vehicles and features which are compatible with this product. The number assigned to each year allows you to determine which installation type should be used for your vehicle. Vehicles Infiniti 07 06 05 0 0 PK-Immobilizer Bypass-Data No Key Req'd DL-Arm Factory Security DL-Disarm Factory Security DL-Door Lock Control DL-Door Unlock DL-Driver Priority Unlock DL-Trunk / Hatch Release RS-x LOCK START (Start control using OEM Remote) RS-x LOCK STOP (Stop control using OEM Remote) RS-RAP Shut Down (Retained ACC Power) RS-Remote Start Ready RS-SmartStart RS-Tach / RPM Output SS-Entry Monitoring ALL Door Pins SS-Entry Monitoring Hood Pin SS-Entry Monitoring Trunk/Hatch Pin SS-Factory Alarm Trigger Monitoring ST-Brake Status (foot brake) ST-Door Locks Status ST-Ignition Status JX5 (Smart Key) Q50 (Smart Key) QX60 (Smart Key) Nissan Altima (Smart Key) Maxima (Smart Key) Murano (Smart Key) Pathfinder (Smart Key) Titan (Smart Key) Legend: DL: OE Door Lock & Alarm Controls FOB: Sync CAN Interface w / FOB Remote PK: Transponder & Immobilizer Override RS: Remote Start & Engine Controls SS: Integrated Security & Monitoring ST: Function/Feature Status

Installation Type Page Important! The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the interface. (-) Driver Door Trigger: Tan, pin 6 5 6 7 8 9 0 5 6 7 8 9 0 0 White 5-pin conn. 9 8 7 6 5 5 0 (+) V: White, pin Gray -pin conn. 9 8 7 6 5 0 9 8 7 6 5 0 9 8 7 6 5 0 9 8 7 6 5 Green 0-pin conn. (-) PTS: Green, pin BCM The BCM may look different on your vehicle, but the connections remain the same. (-) Starter: White or Lt.Blue, pin (+) Accessory: White, pin 6 6 7 (+) Ignition : Green, pin 7 0 (-) Ignition : Pink, pin 0 9 0 Black 0-pin conn. HS CAN Low: Pink, pin 9 HS CAN High: Blue, pin 0 HS CAN High: Tan/Black: HS CAN Low: Tan: (+) V Input: Brown: 7 Hood Pin (+) Accessory Output: Yellow: 8 [] Security Light Interrupt: Orange/Red: 0 [] Security Light Interrupt: Yellow/Red: (+) V Input: Red: (-) Ground: Black: (-) Ignition Output: Black/White: (-) PTS Output: Green/Black: (-) Starter Output: Red/Black: (+) Ignition Output: Gray/Black: 7 (-) Auto Headlamp Shutoff: Violet/Brown: 9 (-) Parking Light Output: Blue/Red: RF Prog. Button DBALL 0 Remote Start Safety Override Switch 6: White/Black: (-) Hood Input 86 87 85 LED 87a Fuse 5A 0 Dash Fusebox 7 6 (+) Parking Lights: Red, pin 5 6 5 0 Brown 6-pin conn. 9 8 You can connect to either a XL0 RFTD OR a SmartStart module. Refer to the SmartStart/XL0 Installation Notes for more information. [] Only required if Security Light Off does NOT operate in data. All adapters are displayed from the wire side (unless specified otherwise).

Type - Vehicle Wiring Reference Chart Page Wire Information Connector Information Function Color Pin Polarity Location Color Pins Infiniti JX5 (Smart Key) 0 HS CAN Low Pink 9 Data BCM located behind the cluster. Black 0 HS CAN High Blue 0 Data BCM located behind the cluster. Black 0 Starter White (-) BCM located behind the cluster. Black 0 Ignition Green 7 (+) BCM located behind the cluster. Black 0 Ignition Pink 0 (-) BCM located behind the cluster. Black 0 Accessory White 6 (+) BCM located behind the cluster. Black 0 Push-to-Start Green (-) BCM located behind the cluster. Green 0 Security Light Interrupt [] Violet 8 Cut BCM located behind the cluster. Green 0 Driver Door Trigger Tan 6 (-) BCM located behind the cluster. Gray V White (+) BCM located behind the cluster. White 5 Parking Lights Red (+) Dash fusebox located in driver dash. Brown 6 Infiniti QX60 / QX60 Hybrid (Smart Key) 0-07 HS CAN Low Pink 9 Data BCM located behind the cluster. Black 0 HS CAN High Blue 0 Data BCM located behind the cluster. Black 0 Starter White (non-hybrid) or Lt. Blue (hybrid) (-) BCM located behind the cluster. Black 0 Ignition Green 7 (+) BCM located behind the cluster. Black 0 Ignition Pink 0 (-) BCM located behind the cluster. Black 0 Accessory White 6 (+) BCM located behind the cluster. Black 0 Push-to-Start Green (-) BCM located behind the cluster. Green 0 Security Light Interrupt [] Violet 8 Cut BCM located behind the cluster. Green 0 Driver Door Trigger Tan 6 (-) BCM located behind the cluster. Gray V White (+) BCM located behind the cluster. White 5 Parking Lights Red (+) Dash fusebox located in driver dash. Brown 6 [] Only required if Security Light Off does NOT operate in data.

Installation Type Page 5 Important! The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the interface. 0 White 5-pin conn. 9 8 7 6 5 5 0 White 5-pin (+) V: White, pin (-) Driver Door Trigger: Violet, pin 6 Gray -pin conn. 6 5 7 8 9 0 5 6 7 8 9 0 9 8 7 6 5 0 9 8 7 6 5 0 9 8 7 6 5 0 9 8 7 6 5 Green 0-pin conn. (-) PTS: Red, pin BCM The BCM may look different on your vehicle, but the connections remain the same. 9 0 9 6 7 (+) Acc. : Lt.Blue, pin 9 Black -pin conn. (in BCM) (-) Starter: Red or Lt. Blue, pin (+) Accessory : Black, pin 6 (+) Ignition : White/Black, pin 7 0 (-) Ignition : Black, pin 0 Black 0-pin conn. HS CAN Low: Pink, pin 9 HS CAN High: Blue, pin 0 HS CAN High: Tan/Black: HS CAN Low: Tan: (+) V Input: Brown: 7 (+) Accessory Output: Yellow: 8 [] Security Light Interrupt: Orange/Red: 0 [] Security Light Interrupt: Yellow/Red: (+) V Input: Red: (-) Ground: Black: (-) Ignition Output: Black/White: (-) PTS Output: Green/Black: (-) Starter Output: Red/Black: (+) Accessory Output: Gray: 6 (+) Ignition Output: Gray/Black: 7 (-) Auto Headlamp Shutoff: Violet/Brown: 9 (-) Parking Light Output: Blue/Red: RF Prog. Button DBALL 0 Hood Pin Remote Start Safety Override Switch 6: White/Black: (-) Hood Input 86 87 85 LED 87a Fuse 5A 0 Dash Fusebox M 6 (+) Parking Lights: Red, pin 6 You can connect to either a XL0 RFTD OR a SmartStart module. Refer to the SmartStart/XL0 Installation Notes for more information. [] Only required if Security Light Off does NOT operate in data. All adapters are displayed from the wire side (unless specified otherwise).

Type - Vehicle Wiring Reference Chart Page 6 Wire Information Connector Information Function Color Pin Polarity Location Color Pins Infiniti Q50 / Q50 Hybrid (Smart Key) 0-07 HS CAN Low Pink 9 Data BCM located in passenger kick. Black 0 HS CAN High Blue 0 Data BCM located in passenger kick. Black 0 Starter Red (non-hybrid) or Lt. Blue (hybrid) (-) BCM located in passenger kick. Black 0 Ignition White/Black 7 (+) BCM located in passenger kick. Black 0 Ignition Black 0 (-) BCM located in passenger kick. Black 0 Accessory Black 6 (+) BCM located in passenger kick. Black 0 Accessory Lt.Blue 9 (+) BCM located in passenger kick. Black Push-to-Start Red (-) BCM located in passenger kick. Green 0 Security Light Interrupt [] Blue 8 Cut BCM located in passenger kick. Green 0 Driver Door Trigger Violet 6 (-) BCM located in passenger kick. Gray V White (+) BCM located in passenger kick. White 5 Parking Lights Red 6 (+) Dash fusebox located in driver kick. White 0 [] Only required if Security Light Off does NOT operate in data.

Installation Type Page 7 Important! The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the interface. 0 White 5-pin conn. 9 8 7 6 5 5 0 (+) V: White or Blue, pin (-) Driver Door Trigger: Pin 6 Gray -pin conn. 6 5 7 8 9 0 5 6 7 8 9 0 9 8 7 6 5 0 9 8 7 6 5 0 9 8 7 6 5 0 9 8 7 6 5 Green 0-pin conn. (-) PTS: Red or Green, pin BCM The BCM may look different on your vehicle, but the connections remain the same. 9 0 (-) Starter: Pin 6 7 0 (+) Accessory: White or Red, pin 6 (+) Ignition : White or Green, pin 7 (-) Ignition : Pink or Green, pin 0 Black 0-pin conn. HS CAN Low: Pink, pin 9 HS CAN High: Blue, pin 0 86 87 85 HS CAN High: Tan/Black: HS CAN Low: Tan: (+) V Input: Brown: 7 (+) Accessory Output: Yellow: 8 [] Security Light Interrupt: Orange/Red: 0 [] Security Light Interrupt: Yellow/Red: (+) V Input: Red: (-) Ground: Black: (-) Ignition Output: Black/White: (-) PTS Output: Green/Black: (-) Starter Output: Red/Black: (+) Ignition Output: Gray/Black: 7 (-) Auto Headlamp Shutoff: Violet/Brown: 9 (-) Parking Light Output: Blue/Red: RF Prog. Button DBALL 0 Hood Pin Remote Start Safety Override Switch 6: White/Black: (-) Hood Input Fuse 5A 87a 0 LED Dash Fusebox 7 6 5 (+) Parking Lights: Red, pin 6 5 0 Brown 6-pin conn. 9 8 You can connect to either a XL0 RFTD OR a SmartStart module. Refer to the SmartStart/XL0 Installation Notes for more information. [] Only required if Security Light does NOT operate in data. All adapters are displayed from the wire side (unless specified otherwise).

Type - Vehicle Wiring Reference Chart Page 8 Wire Information Connector Information Function Color Pin Polarity Location Color Pins Nissan Altima (Smart Key) 0-07 HS CAN Low Pink 9 Data BCM located behind the cluster. Black 0 HS CAN High Blue 0 Data BCM located behind the cluster. Black 0 Starter Brown (-) BCM located behind the cluster. Black 0 Ignition White 7 (+) BCM located behind the cluster. Black 0 Ignition Green 0 (-) BCM located behind the cluster. Black 0 Accessory Red 6 (+) BCM located behind the cluster. Black 0 Push-to-Start Red (-) BCM located behind the cluster. Green 0 Security Light Interrupt [] Green 8 Cut BCM located behind the cluster. Green 0 Driver Door Trigger Brown 6 (-) BCM located behind the cluster. Gray V White (+) BCM located behind the cluster. White 5 Parking Lights Red (+) Dash fusebox located in driver dash. Brown 6 Nissan Maxima (Smart Key) 06-07 HS CAN Low Pink 9 Data BCM located behind the cluster. Black 0 HS CAN High Blue 0 Data BCM located behind the cluster. Black 0 Starter Violet (-) BCM located behind the cluster. Black 0 Ignition White 7 (+) BCM located behind the cluster. Black 0 Ignition Green 0 (-) BCM located behind the cluster. Black 0 Accessory Red 6 (+) BCM located behind the cluster. Black 0 Push-to-Start Red (-) BCM located behind the cluster. Green 0 Security Light Interrupt [] Green 8 Cut BCM located behind the cluster. Green 0 Driver Door Trigger Pink 6 (-) BCM located behind the cluster. Gray V White (+) BCM located behind the cluster. White 5 Parking Lights Red (+) Dash fusebox located in driver dash. Brown 6 Nissan Murano/ Murano Hybrid (Smart Key) 05-07 HS CAN Low Pink 9 Data BCM located behind the cluster. Black 0 HS CAN High Blue 0 Data BCM located behind the cluster. Black 0 Starter White (non-hybrid) or Lt.Blue (hybrid) (-) BCM located behind the cluster. Black 0 Ignition Green 7 (+) BCM located behind the cluster. Black 0 Ignition Pink 0 (-) BCM located behind the cluster. Black 0 Accessory White 6 (+) BCM located behind the cluster. Black 0 Push-to-Start Green (-) BCM located behind the cluster. Green 0 Security Light Interrupt [] Violet 8 Cut BCM located behind the cluster. Green 0 Driver Door Trigger Tan 6 (-) BCM located behind the cluster. Gray V Blue (+) BCM located behind the cluster. White 5 Parking Lights Red (+) Dash fusebox located in driver dash. Brown 6 Nissan Pathfinder (Smart Key) 0-07 HS CAN Low Pink 9 Data BCM located behind the cluster. Black 0 HS CAN High Blue 0 Data BCM located behind the cluster. Black 0 Starter White or Lt. Blue (-) BCM located behind the cluster. Black 0 Ignition Green 7 (+) BCM located behind the cluster. Black 0 Ignition Pink 0 (-) BCM located behind the cluster. Black 0 Accessory White 6 (+) BCM located behind the cluster. Black 0 Push-to-Start Green (-) BCM located behind the cluster. Green 0 Security Light Interrupt [] Violet 8 Cut BCM located behind the cluster. Green 0 Driver Door Trigger Tan 6 (-) BCM located behind the cluster. Gray V White (+) BCM located behind the cluster. White 5 Parking Lights Red (+) Dash fusebox located in driver dash. Brown 6 [] Only required if Security Light Off does NOT operate in data.

Installation Type Page 9 Important! The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the interface. (+) Accessory : Blue, pin 9 0 White 5-pin conn. 9 8 7 6 5 5 0 (+) V: White, pin (-) Driver Door Trigger: Tan, pin 6 Gray -pin conn. 6 5 7 8 9 0 5 6 7 8 9 0 9 8 7 6 5 0 9 8 7 6 5 0 9 8 7 6 5 0 9 8 7 6 5 Green 0-pin conn. (-) PTS: Green, pin BCM The BCM may look different on your vehicle, but the connections remain the same. 6 7 0 9 Black -pin conn. (-) Starter: White or Lt.Blue, pin (+) Accessory: White, pin 6 (+) Ignition :Green, pin 7 (-) Ignition : Pink, pin 0 Black 0-pin conn. 9 0 HS CAN Low: Pink or Black, pin 9 HS CAN High: Blue, pin 0 HS CAN High: Tan/Black: HS CAN Low: Tan: (+) V Input: Brown: 7 (+) Accessory Output: Yellow: 8 [] Security Light Interrupt: Orange/Red: 0 [] Security Light Interrupt: Yellow/Red: (+) V Input: Red: (-) Ground: Black: (-) Ignition Output: Black/White: (-) PTS Output: Green/Black: (-) Starter Output: Red/Black: (+) Accessory Output: Gray: 6 (+) Ignition Output: Gray/Black: 7 (-) Auto Headlamp Shutoff: Violet/Brown: 9 (-) Parking Light Output: Blue/Red: RF Prog. Button DBALL 0 Hood Pin Remote Start Safety Override Switch 6: White/Black: (-) Hood Input LED Fuse 5A 86 87 85 87a 0 6 White 6-pin conn. (electric brake pre-wiring 5 harness left of steering wheel) (+) Parking Lights: Blue, pin You can connect to either a XL0 RFTD OR a SmartStart module. Refer to the SmartStart/XL0 Installation Notes for more information. [] Only required if Security Light Off does NOT operate in data. All adapters are displayed from the wire side (unless specified otherwise).

Type - Vehicle Wiring Reference Chart Page 0 Wire Information Connector Information Function Color Pin Polarity Location Color Pins Nissan Titan (Smart Key) 06-07 HS CAN Low Pink or Black 9 Data BCM located above accelerator pedal. Black 0 HS CAN High Blue 0 Data BCM located above accelerator pedal. Black 0 Starter White or Lt.Blue (-) BCM located above accelerator pedal. Black 0 Ignition Green 7 (+) BCM located above accelerator pedal. Black 0 Ignition Pink 0 (-) BCM located above accelerator pedal. Black 0 Accessory White 6 (+) BCM located above accelerator pedal. Black 0 Accessory Blue 9 (+) BCM located above accelerator pedal. Black Push-to-Start Green (-) BCM located above accelerator pedal. Green 0 Security Light Interrupt [] Violet 8 Cut BCM located above accelerator pedal. Green 0 Driver Door Trigger Tan 6 (-) BCM located above accelerator pedal. Gray V White (+) BCM, right of steering column. White 5 Parking Lights Blue (+) Electric brake pre-wiring, left of steering wheel. White 6 [] Only required if Security Light Off does NOT operate in data.

SmartStart/XL0 Installation Notes Page The DBALL Remote Start Ready (RSR) solution offers three () configuration options to control your system: x OEM Lock Remote Start Activation, RF Kits or SmartStart (all sold separately). This section provides specific installation information for SmartStart and XL0. SmartStart Revision A SmartStart is optional and not included. It MUST be purchased separately. Configuration Wires (White & Brown or Blue) Cut Brown or Blue Loop OR DBALL CABLE pins DD ( pins, white) pins, not used LED SmartStart The modules must be connected in a specific order. Refer to the Module Programming section for more information. SmartStart Revision B SmartStart is optional and not included. It MUST be purchased separately. Configuration Wires (Gray & White) Connect Gray wire to (-) Ground 5 pins DBALL CABLE pins pins, not used THIS SIDE UP DD ( pins, white) LED The modules must be connected in a specific order. Refer to the Module Programming section for more information. RF Kit The optional XL0 and antenna are not included and MUST be purchased separately. DBALL XOVER LED XL0 Prog. Button Antenna. Use the DD Crossover (XOVER) cable that is provided with XL0, and NOT the one in the DBALL package.. The modules must be connected in a specific order. Refer to the Module Programming section for more information. RF Kit & PKE Combination Refer to the Passive Keyless Entry (PKE) Installation Guide (N0T) for detailed wiring information. RF Kit, PKE & SmartStart BT Combination Refer to the Passive Keyless Entry (PKE) Installation Guide (N0T) for detailed wiring information.

Module Programming Page Refer to the LED Diagnostics section on pages 5-6 for more information and for troubleshooting purposes. Important Make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to ensure everything is correct prior to moving onto the next step. Note: Before connecting either the XL0 or SmartStart module to DBALL, it is important to ensure that the proper feature and function programming is selected using XpressVIP (version.5 or higher). Visit www.directechs.com to download the latest version of the application. Warning! To take advantage of advanced features, you must use XpressVIP.5 (and higher) or the Directechs Mobile app. Flashing a module using your computer:. Connect the interface module to your computer using the XKLoader.. Go to www.directechs.com using Internet Explorer, and select the Config for RSR button.. Follow the instructions to select your vehicle, installation type, and configure your options.. Once you have configured the firmware options, click on the FLASH button. Flashing a module using your smartphone or tablet. Connect the interface module to your XKLoader.. Launch the Directechs Mobile app on your smartphone or tablet.. Select FLASH YOUR MODULE and follow the on screen instructions. When the flashing operation is successful, you can proceed with the programming instructions below. SmartStart Installation The DBALL module must be disconnected from any power source before SmartStart can be connected to it. Failing to do so could damage DBALL. a. To ensure that the DD communication between SmartStart and DBALL works properly, the Gray wire must be connected to a ground source (Rev B SmartStart), and the Brown or Blue loop must be cut (Rev A SmartStart). b. Do NOT connect the -pin harness (on SmartStart). Power and ground will be provided by the DBALL DD connector. Connect SmartStart to DBALL using the DD port. OR XL0 Installation Connect XL0 to DBALL using the DD port. SmartStart XL0 DD 0-pin DD 0-pin Connect the 0-pin, -pin and -pin harnesses to DBALL, then wait until the LED turns ON solid red. st DD 0-pin rd nd -pin -pin & Solid Important: Do NOT press the brake pedal. Press the Push-to-Start (PTS) button twice to turn the ignition ON. If the module has not been programmed, the LED flashes throughout the process. This can take up to 5 seconds. If the module is already programmed, the LED turns OFF when the ignition is turned ON. Press x Do NOT press the brake pedal & Go to the next page to complete the module programming.

Page The LED turns ON solid green for seconds, then turns OFF once the module has been successfully programmed. Solid x secs & Off Press the PTS button once to turn the ignition OFF. Press x You have successfully completed the module programming sequence. Module Reset A module reset will only erase programming performed in the previous steps. All settings (firmware) and settings flashed to the module using the web config tool will not be affected. If required for your installation, connect the 0-pin & -pin harnesses to the module. Press and hold the programming button, then connect the -pin harness to the module. st DD 0-pin th nd rd -pin -pin Wait seconds until the LED turns ON solid orange then release the programming button. The LED turns ON solid red. & & Hard Reset Solid Release Solid Warning Against Executing a Hard Reset! A hard reset will revert the flashed firmware back to its default settings. Depending on the installation, some settings (such as RFTD and DD options) may have to be reconfigured. See the Feature & Option List section of this guide. If required for your installation, connect the 0-pin & -pin harnesses to the module. Press and hold the programming button, then connect the -pin harness to the module. st DD 0-pin th nd rd -pin -pin Wait seconds until the LED turns ON solid orange, and wait 0 more seconds until the LED starts to flash orange and red. Solid & Release the programming button. The LED turns ON solid red. Release & Solid

Feature & Option List Page It is recommended to configure all the features and options listed below using the configuration tool found on the module flashing page on www.directechs.com. The web offers more options such as RSR; however, manual configuration of the features is possible using the information on this page. * Default Option Feat. Operation /Options Description. No RF Output Module is connected to a remote starter using a standard installation. RFTD Output Type. RFTD Output* Module is connected to an XL0 using an RSR or RXT installation (when available).. SmartStart Module is connected to SmartStart using an RSR or RXT installation (when available). Unlock Driver Priority Smart OEM Alarm Control. Driver priority* Feature Programming To enter feature programming routine - Turn the ignition ON, then OFF. - Within 5 seconds, press and HOLD the programming button until the LED turns ON orange (after seconds). Release the Programming button. - The LED will flash green once slowly to indicate the feature number is. After a short delay, the LED flashes red rapidly to indicate the current option of feature (i.e. x green followed by x red indicates feature is set to option ). The flashing sequence will repeat until a new command is entered. Changing feature options - Press the lock/arm or unlock/disarm button on aftermarket transmitter to change the option of the selected feature. When installing the DBALL in RSR using x OEM Lock Remote Start Activation only, there is no aftermarket transmitter on which to press lock/unlock to change the options of the selected feature. Tapping the green or blue lock/unlock wires on the black 0-pin harness to ground will change the option for the selected feature. - The LED flashes red rapidly the number of times equal to the current option number. After a short delay, the LED flashes green slowly the number of times to indicate the current feature. The flashing sequence will repeat until a new command is entered. Accessing another feature - Press and release the programming button a number of times to advance from the current feature to the next desired feature. - The LED flashes green slowly the number of times equal to the feature number. After a short delay, the LED flashes red rapidly to indicate the current option of the current feature. The flashing sequence will repeat until a new command is entered. When the maximum number of features or options is reached, the LED will start flashing again from the first feature or option. Once a feature is programmed - Other features can be programmed. - The feature programming can be exited. Unlocks only the driver door when the button is first pressed, and unlocks all doors when it is pressed a second time within 5 seconds.. All Unlocks all doors when the button is first pressed. The OEM alarm will not be controlled by the interface upon remote start. No disarm or. Disabled arm command will be executed at the beginning or end of the sequence; it must be controlled by the Remote Starter.. Safelock. Enabled* Smart OEM Alarm Control will behave like a standard Safelock feature on a remote starter. It will unlock at the beginning of the sequence, and relock after start and shutdown. Smart OEM Alarm Control will synchronize with the OEM alarm so that it will disarm and rearm the vehicle in the remote start sequence, only when required. Smart OEM Alarm Control will monitor the alarm and door lock status to detect if the disarm or rearm is required. If the vehicle is unlocked or is not equipped with factory alarm, the disarm/rearm will not be executed. Programming Button Exiting feature programming - No activity for 0 seconds; after 0 seconds, the LED will turn ON orange for seconds to confirm the end of the programming sequence. OR - Press and HOLD the programming button for seconds. After seconds, the LED will turn ON orange for seconds to confirm the end of the programming sequence.

LED Diagnostics & Troubleshooting Page 5 LED Description Troubleshooting Module Programming Off Module has no power. Make sure the DD harness is connected or that the Volt is present between the red and black wires. If the Volt is present, the module may be defective. Solid red Waiting to begin the programming sequence. Ensure the correct programming procedure is being followed. red & green Solid orange green Initialization failed. Transponder functions were skipped. All required CAN networks has been detected. Reset the module and complete the programming again. If the issue persists, please contact Technical Support. (If compatible) when RXT mode is not desired or convenience features are needed, please reset and reprogram the module. Normal operation. orange orange slowly Solid green x secs of CAN networks has been detected. Normal operation KeyGO initiated. Module was successfully programmed with all functions. Normal operation Please follow the steps indicated in Module programming to complete the KeyGO programming. Solid orange Module was successfully programmed without x secs transponder functions. Module Programming - Error Codes red x red x red x red x CAN not detected. J850 not detected. CAN not detected. Bypass data not detected. Normal operation. Check the CAN Orange/Green and Orange/Brown wire connections. Wake up the data bus by turning the ignition on and try again. If your installation does not require this connection, skip this step by pressing the programming button 5 times. Check the J850 wire connection. Wake up the data bus by turning the ignition on and try again. Check the CAN Tan and Tan/Black wire connections. Wake up the data bus by turning the ignition on and try again. If your installation does not require this connection, skip this step by pressing the programming button 5 times. Check the bypass line connection. If more than one wire is used, make sure they are not inverted. Ensure the vehicle still operates correctly using the factory key. red x red x 5 red x 6 red x 7 Bypass processing error. ISO not detected. ISO not detected. MUX not detected. The bypass calculation failed. Reset the module and try again. If the condition persists, please contact Technical Support. The Yellow/Black wire did not detect the expected signal. Refer to "Installation (wiring diagrams & vehicle wiring reference charts)" to check the connections. The Orange/Black wire did not detect the expected signal. Refer to "Installation (wiring diagrams & vehicle wiring reference charts)" to check the connections. The Violet/Green or Violet/Brown wire did not detect the expected voltage value. Refer to "Installation (wiring diagrams & vehicle wiring reference charts)" to check the connections.

Page 6 LED Description Troubleshooting External module synchronization ( red, red then orange) x 0 OBDII feature is not supported. Activation Ground When Running (Status) green Ground When Running (Status) command received. The diagnostic data bus was not detected, therefore the SmartStart features will be limited. The module has initialized the remote start sequence. red & orange green quickly red x 0 red x Commands orange x orange x orange x orange x orange x 5 orange x 6 Ignition ON command received. Start ON command received. PTS shutdown error. CAN bus incorrectly detected. LOCK command received. UNLOCK command received. TRUNK command received. AUX command received. AUX command received. AUX command received. The module has received the Ignition ON command and is processing the remote start sequence. The module has received the Start ON command and is processing the remote start sequence. The PTS output from the module was not activated due to safety protection. Verify the CAN and CAN connections. Refer to Installation (wiring diagrams & vehicle wiring reference charts) to check the connections. If the bypass module fails to flash, it did not receive the signal. Commands can come from RF or DD. Shutdown codes green x red x red x red x red x RSR codes red x 7 red x 9 Takeover successful. Runsafe was not disabled. Brake was not detected. Smart key was not detected. Speed was detected. x OEM Lock Remote Start Activation was attempted when RFTD feature is disabled. Feature error. Normal operation. No UNLOCK command was received prior to opening the door, or the 5 second timer expired in takeover mode. The brakes were not detected, which prevents the system from shutting down the vehicle. The smart key was not detected, which prevents the system from shutting down the vehicle. The vehicle was detected as moving, which prevents the system from shutting it down. Activated from Web automatically when using RSR flash tool or can be done manually. Refer to feature programing section for more information. An RSR feature file mismatch was detected. Please contact Technical Support.

Parking Light Error Codes Page 7 The parking lights on your vehicle will flash a specific number of times seconds following an unscheduled shutdown or failure to start. Each flashing pattern is described below. Diagnostic Runtime expired. Over-rev shutdown. Low/No RPM. Transmitter shutdown. 5 Brake shutdown. 6 Hood shutdown/remote start safety override switch is ON*. 7 Remote start safety override switch is ON*. * If the vehicle hood status is supported through data, it will also report a 7 flash safety override code.

Limited One Year Consumer Warranty Page 8 For a period of ONE YEAR from the date of purchase of a Directed Electronics remote start or security product, Directed Electronics. ( DIRECTED ) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, the security or remote start accessory piece (hereinafter the Part ), which proves to be defective in workmanship or material under normal use, provided the following conditions are met: the Part was purchased from an authorized DIRECTED dealer; and the Part is returned to DIRECTED, postage prepaid, along with a clear, legible copy of the receipt or bill of sale bearing the following information: consumer s name, address, telephone number, the authorized licensed dealer s name and complete product and Part description. This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to its intended purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defect in materials or construction. TO THE MAXIMUM EXTENT ALLOWED BY LAW, EXCEPT AS STATED ABOVE, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NONINFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING DEALERS OR INSTALLERS. DIRECTED IS NOT OFFERING A GUARANTEE OR INSURANCE AGAINST VANDALISM, DAMAGE, OR THEFT OF THE AUTOMOBILE, ITS PARTS OR CONTENTS, AND DIRECTED HEREBY DISCLAIMS ANY LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE, OR VANDALISM. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER S PURCHASE PRICE OF THE PART. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR AT DIRECTED S OPTION THE PART AS DESCRIBED ABOVE. This warranty only covers Parts sold within the United States of America and Canada. Parts sold outside of the United States of America or Canada are sold AS-IS and shall have NO WARRANTY, express or implied. Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights and you may also have other rights that vary from State to State. DIRECTED does not and has not authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this Part. For further details relating to warranty information of Directed products, please visit the support section of DIRECTED s website at: www.directed.com 90-00-0 0-07 This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the select vehicle list upon completion of compatibility testing. Visit website for latest vehicle application guide. DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for any consequential damages sustained in connection with the part(s) installation. The manufacturer and it s distributors will not, nor will they authorize any representative or any other individual to assume obligation or liability in relation to the interface kit / data bus interface part(s) other than its replacement. N.B.: Under no circumstances shall the manufacturer and distributors of this product be liable for consequential damages sustained in connection with this product and neither assumes nor authorizes any representative or other person to assume for it any obligation or liability other than the replacement of this product only. Protected by U.S. Patents: 5,79,55; 6,0,60 B *; 6,,00 B; 6,9,6 B; 6,75,7 B; 6,97,7 B; 6,6,876 B; 6,9,5 B; 6,59, B; 6,696,97 B; 6,756,885 B; 6,756,886 B; 6,77,67 B; 6,8,89 B; 6,9,750 B; 7,00,0 B; 7,05,80 B; 7,0,86 B; 7,06,6 B; 7,06,7 B; 7,068,5 B; 7,05,679 B; Cdn. Patent:,0,8;,,99;,5,0;,5,0;,5,07;,5,08;,5,0;,0,97;,6,670;,5,089; European Patent:,05,8; Pat. Pending:,9,06. Made in Canada.

Quick Reference Guide DBALL-NISS08 Remote Start Ready (RSR) Installation Vehicle Takeover with Push-to-Start (PTS) Pit Stop Mode Press 5 the remote start button on the transmitter to start the vehicle.* Press the Unlock button on the factory or aftermarket remote.* Press the brake pedal, put the car in gear and drive off. Press Unlock button on either remote* Complete the following steps within 5 seconds or the vehicle will shut down. Enter the vehicle, while making sure the factory remote is inside with you. Important: Do NOT press the brake pedal. Press the PTS button twice to turn the ignition ON. Wait for the LED indicator around the PTS button to illuminate prior to proceeding to step 5. Do NOT press brake pedal Ready to drive off Press remote start button* X OR Enter vehicle with Key Fob ENGINE START STOP PUSH The Pit Stop Mode feature is practical when you need to stop and run an errand, but wish to keep the engine running. Stop the vehicle in a safe parking spot and put the gear in Park (P). Press the button to remote start the vehicle.* The parking lights will flash once to indicate the vehicle is now in Pit Stop Mode. It is now safe to leave the engine running and exit the vehicle with the factory remote in hand. Note: We recommend that you always lock the doors of your vehicle when leaving it unattended. Stop & put vehicle in Park (P) Press remote start button* * Your aftermarket remote may differ from the model shown in the illustrations. Parking Light Error Codes & Exit vehicle with Smart Key The parking lights on your vehicle will flash a specific number of times seconds following an unscheduled shutdown or failure to start. Each flashing pattern is described below. P * Your aftermarket remote may differ from the model shown in the illustrations. Diagnostic Runtime expired. Over-rev shutdown. Low/No RPM. Transmitter shutdown. 5 Brake shutdown. 6 Hood shutdown/remote start safety override switch is ON*. 7 Remote start safety override switch is ON*. * If the vehicle hood status is supported through data, it will also report a 7 flash safety override code.

Quick Reference Guide DBALL-NISS08 Remote Start Ready (RSR) Installation Remote Start Ready (RSR) Remote Start Ready (RSR) is a function that enables the interface module to remote start the vehicle completely on its own. Consequently, there is no need for an aftermarket or an OEM remote starter in order to start the vehicle from a distance. x OEM Lock Remote Start Activation This solution includes the option to remote start your vehicle by pressing the Lock button times consecutively. If your vehicle allows the OEM remote to remain active while the engine is running, you may shut down your remote starter by pressing the Lock button times once more. Note: The range offered by OEM remotes is limited and typically requires you to be within eyesight of the vehicle to control it. List of Available Commands Note that the information below is for Viper, Clifford and Python models. Icons and commands may differ depending on the remote brand and model purchased. Refer to your authorized installation center for more information. Button(s) x + x + x + Actions Press & hold for second to lock. Press & hold for second to unlock. Press & hold for second to remote start. Press & hold for 5 seconds to activate the trunk release (optional). Press once, then to activate the rear hatch/tail glass release (optional).* Press times, then to activate the panic mode. Press once, then to reset the remote starter runtime. * This output is configurable. see your authorized installation center for more information.

Quick Reference Guide DBALL-NISS08 Remote Start Ready (RSR) Installation SmartStart Compatible Notes This system is compatible with Directed SmartStart.0. For a complete list of supported features, please visit www.mysmartstart.com. What is SmartStart? Now you can remote start, lock and unlock your car just by pushing a button on your smartphone; using the SmartStart App from Directed, the leader in vehicle security and remote start. The simple graphical interface gives you control over the following features of your installed remote start or security with remote start system: Ÿ Lock/Arm Ÿ Unlock/Disarm Ÿ Remote Car Starter Ÿ Trunk Release Ÿ Panic Ÿ Aux Channels You can also control multiple vehicles great for families and assign more than one user to control a vehicle. It's easy with SmartStart! But, this is only the beginning! SmartStart is loaded with additional features including GPS tracking, SmartSchedule, vehicle status, roadside assistance, home control, parked car finder and more..0 enables a "Cloud-Connected Car" like never before, providing an entirely new level of -way interaction with your vehicle. Connectivity is managed through the Directed Cloud Services (DCS) network linking car, app, end user, and the Internet. For more information, visit www.mysmartstart.com.