E SinglFuse SF-0603SPxxxM Series Features n Single blow fuse for overcurrent protection n 1608 (EIA 0603) miniature footprint n Time Lag fuse n UL 248-14 listed n RoHS compliant* and halogen free** n Multilayer SMD design n Surface mount packaging for automated assembly SF-0603SPxxxM Series - Time Lag Multilayer Surface Mount Fuses Electrical Characteristics Model Rated Current Resistance Rated Interrupting Typical Fusing Time (Amps) (Ω) Typ.*** Voltage Rating I 2 t (A 2 s) **** SF-0603SP100M-2 1.00 0.200 0.093 SF-0603SP150M-2 1.50 0.100 0.18 SF-0603SP200M-2 2.00 0.052 0.32 SF-0603SP250M-2 2.50 0.041 0.63 DC 32 V SF-0603SP300M-2 3.00 Open within 0.031 0.87 50 A SF-0603SP350M-2 3.50 1~120 sec. at 0.021 1.20 DC 32 V SF-0603SP400M-2 4.00 200 % rated 0.017 2.30 SF-0603SP450M-2 4.50 current 0.015 2.70 SF-0603SP500M-2 5.00 0.013 3.20 SF-0603SP600M-2 6.00 0.010 4.00 DC 32 V SF-0603SP700M-2 7.00 0.008 5.00 80 A SF-0603SP800M-2 8.00 0.006 7.00 *** Resistance value measured with 10 % rated current at 25 C ambient. Tolerance ±25 %. **** Melting I 2 t calculated at 0.001 second pre-arcing time. Reliability Testing No. Test Requirement Test Condition Test Reference 1 Soldering heat resistance One dip at 260 C for 60 seconds 2 Solderability Minimum 95 % coverage One dip at 245 C for 5 seconds 3 Thermal shock 4 Moisture resistance 5 Salt spray 6 Mechanical vibration 7 Mechanical shock 8 Life DCR change ±15 % No excessive corrosion No excessive corrosion No electrical opens during testing Voltage drop change shall be less than ±20 % of initial value Method 210 Method 208 100 cycles between -65 C and +125 C Method 107 10 cycles 48 hour exposure, 5 % salt solution 0.4 inch D.A. or 30 G between 5-3000 Hz 1500 G, 0.5 ms, half-sine shocks 80 % rated current (75 % for < 1 A fuses) for 2000 hours at ambient temperature between +20 C and +30 C Method 106 Method 101 Method 204 Method 213 Refer to STP document Agency Recognition UL File Number... E198545 Asia-Pacific: Tel: +886-2 2562-4117 Email: asiacus@bourns.com EMEA: Tel: +36 88 520 390 Email: eurocus@bourns.com The Americas: Tel: +1-951 781-5500 Email: americus@bourns.com www.bourns.com WARNING Cancer and Reproductive Harm - www.p65warnings.ca.gov * RoHS Directive 2002/95/EC Jan. 27, 2003 including annex and RoHS Recast 2011/65/EU June 8, 2011. ** Bourns considers a product to be halogen free if (a) the Bromine (Br) content is 900 ppm or less; (b) the Chlorine (Cl) content is 900 ppm or less; and (c) the total Bromine (Br) and Chlorine (Cl) content is 1500 ppm or less. SinglFuse is a trademark of Bourns, Inc.
SinglFuse SF-0603SPxxxM Series Applications n Portable memory n LCD monitors n Disk drives n PDAs n Digital cameras n MP3 players n Cell phones n Rechargeable battery packs n Battery chargers n Set-top boxes n Industrial controllers n Battery Management Systems (BMS) n LED lighting n Power tools SF-0603SPxxxM Series - Time Lag Multilayer Surface Mount Fuses Environmental Characteristics Operating Temperature...-55 C to +125 C Storage Conditions Temperature... +5 C to +35 C Humidity...40 % to 75 % Shelf Life...2 years from manufacturing date Moisture Sensitivity Level... 1 ESD Classification (HBM)... Class 6 Typical Part Marking Represents total content. Layout may vary. E RATED CURRENT (A) E = 1.00 M = 4.00 G = 1.50 T = 4.50 I = 2.00 N = 5.00 J = 2.50 O = 6.00 K = 3.00 P = 7.00 L = 3.50 R = 8.00 Product Dimensions How to Order SinglFuse Product Designator SMD Footprint 0603 = 1608 (EIA 0603) size Fuse Blow Type SP = Time Lag Rated Current 100 ~ 800 (1.00 A ~ 8.00 A) Structure Type M = Multilayer Packaging Type - 2 = Tape & Reel SF - 0603 SP 100 M - 2 Construction MARKING Packaging Quantity MASKING LAYER MARKING MASKING LAYER FUSE ELEMENT CERAMIC BODY TERMINATION 4,000 pieces per 7-inch reel Recommended Pad Layout 1.6 ± 0.15 (.063 ±.006) 0.80 ± 0.15 (.031 ±.006) 0.80 (.031) 0.80 ± 0.15 (.031 ±.006) 0.80 ± 0.15 (.031 ±.006) 1.00 (.039) 0.36 ± 0.15 (.014 ±.006) DIMENSIONS: MM (INCHES) 2.20 (.087) Current Rating Thermal Derating Curve DERATING (%) 105 100 95 90 85 80 75 70 65 60 55 50-55 -35-15 5 25 45 65 85 105 125 MAXIMUM OPERATING TEMPERATURE ( C)
SF-0603SPxxxM Series - Time Lag Multilayer Surface Mount Fuses Solder Reflow Recommendations TEMPERATURE ( C) T p T L 25 T smax T smin MAX. RAMP UP RATE = 3 C/s MAX. RAMP DOWN RATE = 6 C/s PREHEAT AREA t s TIME 25 C TO PEAK t L t p T c -5 C Profile Feature Preheat / Soak: Temperature Min. (T smin ) Temperature Max. (T smax ) Time (t s ) from (T smin to T smax ) Ramp Up Rate (T L to T p ) Pb-Free Assembly 150 C 200 C 60~120 seconds 3 C / second max. Liquidous Temperature (T L ) 217 C Time (t L ) maintained above T L 60~150 seconds Peak Package Body Temperature (T p ) Time (t p )* within 5 C of the specified classification temperature (T c ) 260 C 30 seconds* TIME Ramp Down Rate (T p to T L ) 6 C / second max. Time 25 C to Peak Temperature 8 minutes max. * Tolerance for peak profile temperature (T p ) is defined as a supplier minimum and a user maximum. Recommended Temperature Profile for Wave Soldering 260 10 sec. max. Wave soldering is suitable for 0603 size models. TEMPERATURE ( C) 150 PREHEATING 120 seconds TIME
SF-0603SPxxxM 3312-2 mm Series SMD - Time Trimming Lag Multilayer Potentiometer Surface Mount Fuses Average Pre-Arcing Time vs. Current Curves Average I 2 t vs. t Curves 100 10 3.50 A 4.00 A 3.00 A 4.50 A 2.50 A 5.00 A 2.00 A 1.50 A 1.00 A 6.00 A 7.00 A 8.00 A 10000 1000 8.00 A 7.00 A 6.00 A 5.00 A 4.50 A 4.00 A 3.50 A 3.00 A 2.50 A 2.00 A 1.50 A 1.00 A 100 PRE-ARCING TIME (SECONDS) 1 0.1 0.01 I2t (A2s) 10 1 0.1 0.001 1 10 100 CURRENT (A) 0.01 0.001 0.01 0.1 1 10 100 TIME (SECONDS) REV. C, 01/19
SF-0603SPxxxM 3312-2 mm Series SMD Tape Trimming and Reel Packaging Potentiometer Specifications SF-0603SPxxxM Series Tape Dimensions per EIA 481-2 W 8.00 ± 0.10 (.315 ±.004) P 0 4.0 ± 0.10 (.157 ±.004) P 1 4.0 ± 0.10 (.157 ±.004) P 2 2.0 ± 0.05 (.079 ±.002) A 0 1.00 ± 0.10 (.039 ±.004) B 0 1.80 ± 0.10 (.071 ±.004) F 3.5 ± 0.05 (.138 ±.002) E 1 1.75 ± 0.10 (.069 ±.004) D 0 1.50 + 0.10 (.059 +.004) PACKAGING: Paper tape, 4,000 pcs. per reel 13.40 ± 0.50 (.539 ±.020) 2.20 ± 0.30 (.087 ±.012) 0.8 0.6 0.4 0.2 178.00 ± 1.00 (7.008 ±.039) DIA. 60.20 ± 0.50 (2.370 ±.020) DIA. 0.2 0.4 0.6 0.8 13.20 +0.3/-0.2 (.520 +.012/-.008) DIA. 1.20 ± 0.20 (.047 ±.008) 1.40 ± 0.20 (.055 ±.008) E 1 D 0 P 0 P 2 F W B 0 DIMENSIONS: MM (INCHES) P 1 A O K O DIRECTION OF UNREELING
Legal Disclaimer Notice This legal disclaimer applies to purchasers and users of Bourns products manufactured by or on behalf of Bourns, Inc. and Unless otherwise expressly indicated in writing, Bourns products and data sheets relating thereto are subject to change and complete before placing orders for Bourns products. The characteristics and parameters of a Bourns product set forth in its data sheet are based on laboratory conditions, and statements regarding the suitability of products for certain types of applications are based on Bourns knowledge of typical requirements in generic applications. The characteristics and parameters of a Bourns product with other components the actual performance of the Bourns product as meeting the requirements of a particular industry of Bourns products are responsible for ensuring compliance with safety-related requirements and standards applicable to Bourns on a case-by-case basis, use of any Bourns Bourns standard products that are suitable for use in aircraft standard the user s sole risk. custom products shall be negotiated on a case-by-case basis by Bourns and the user for which such Bourns standard products shall also apply to such Bourns custom products. Users shall not sell, transfer, export or re-export any Bourns Bourns products and Bourns technology and technical data may not under any circumstance be exported or re-exported to countries subject to international sanctions or embargoes. Bourns products may not, without bilingual versions are available at: Web Page: http://www.bourns.com/legal/disclaimers-terms-and-policies PDF: http://www.bourns.com/docs/legal/disclaimer.pdf