Platform: DBALL/DBALL Firmware: GM Rev.: 050 Update Alert: Firmware updates are poed to e web on a regular basis. We recomme at you check for firmware a/or inall guide updates prior to inalling is product. Inallation Guide Doorlock a transpoer interface for many of e late models of Buick, Cadillac, Chevrolet, Oldsmobile, Pontiac a Saturn vehicles. Features include RAP shutdown, door trigger sensing a tach output. Iex Vehicle Application Guide... Wiring Diagram... 0 0 Programming Module Programming... Module Reset... Ha Reset... Feature & Option Li... Feature Programming... 0 05 05 06 07 LED Diagnoics & Troubleshooting... Limited One-Year Consumer Warranty... Quick Reference Guide... 08 09 0 Buick, Cadillac, Chevrolet, Oldsmobile, Pontiac a Saturn are regiered trademarks a property of eir respective companies.
Platform: DBALL/DBALL Firmware: GM Vehicle Application Guide Rev.: 050 Page The table below lis e vehicles a features which are compatible wi is product. Refer to e following pages for more information on inallation wiring, programming a troubleshooting for ese vehicles. Vehicles Buick 008 007 006 005 00 00 00 00 000 999 998 Allure D D LeSabre D D Cadillac CTS D D DeVille D D Seville SLS D D Seville STS D D SRX D D Chevrolet Impala D D Monte Carlo D D Oldsmobile Alero D D Aurora D D Pontiac Bonneville D D Gra Am D D [] In some vehicles, GM firmware may not control e doorlocks via data. Once programmed, te e door lock inputs to determine wheer GM firmware will activate ese functions via data. If ere is no activation, e door lock syem will need to be controlled in analog via e remote arter. CC-Heated Mirrors CC-Heated Seats Activation CC-Power Mirror Memory CC-Power Seat Memory DL-Arm Factory Security DL-Disarm Factory Security [] DL-Door Lock Control [] DL-Door Unlock [] DL-Driver Priority Unlock [] DL-Trunk / Hatch Release [] FOB-Control of aftermarket alarm wi OEM remote PK-Immobilizer Bypass-Data No Key Req'd RS-RAP Shut Down (Remote ACC Power) RS-Tach / RPM Output SS-Entry Monitoring ALL Door Pins SS-Entry Monitoring Driver Door Pin SS-Entry Monitoring Trunk/Hatch Pin Lege: D: Data-to-Data (DD) only CC: Comfort & Convenience Controls PK: Transpoer & Immobilizer Override : DD & Wire-to-Wire (WW) DL: OE Door Lock & Alarm Controls RS: Engine Start & Status FOB: Sync CAN Interface w / FOB Remote SS: Entry Point Status-Security
Platform: DBALL/DBALL Firmware: GM Wiring Diagram Rev.: 050 Page ONLY for 998-000 Cadillac Seville STS (-) Starter Enable: Yellow/Black, pin G F G H I J Passlock Module (right side of eering column) E D C B A (+) V (-) Grou (+) Accessory [] Parking Lights (+) Starter (+) Ignition Output [] (-) Hood Input (+) Brake [] (AC) Tach Input (-) Trunk Status Input (-) Door Status Input (-) E-Brake Status Input Starter Remote (-) Starter (-) Lock Output (-) Unlock Output (-) Rear Hatch or Trunk Release Output (-) AUX (Heated Seats) Output [] (-) GWR (Status) J850: Violet, pin 8 9 6 Diagnoic connector OBDII (connector side view) J850: Violet/Yellow: (+) V (-) Grou (+) V: Red: (-) Grou: Black: (-) E-Brake Status Output: Black/White: (-) Door Status Output: Green/White: (-) Trunk Status Output: Red/Black: 0 0: Blue/White: (-) GWR (Status) Input 6: White/Black: (-) AUX (Heated Seats) Input [] : Red/White: (-) Rear Hatch or Trunk Release Input : Blue: (-) Unlock Input [] (AC) Tach Output: Violet/White: 5 : Green: (-) Lock Input RF Prog. Button LED DBALL/ DBALL (+)V RX (-) Grou TX P#: XKDD65 Not required in DD mode. [] Tach wire is an optional connection required on some remote arters, which do not support a tach signal in DD. [] There may be more an one inance for certain vehicles. Go to www.directechs.com for more information on vehicle-specific wiring connections. [] Heated seat feature mu be enabled, see Feature Programing on page 7. Do not use GWR (Status) wire to activate heated seat feature. This wire needs to see a pulse after art for proper operation. Unless specified oerwise, all connectors are displayed from e wire side, wi e exception of e OBDII diagnoic connector.
Platform: DBALL/DBALL Firmware: GM Module Programming Rev.: 050 Page Refer to e LED Diagnoics section for more information a for troubleshooting purposes. Important Make all e required connections to e vehicle, as described in e wiring diagram(s) fou in is guide, a double check to ensure everying is correct prior to moving onto e next ep. Warning! To take advantage of advanced features, you mu use XpressVIP.5 or higher. Using version.9 or. will limit available functions a features.. Connect e interface module to your computer using e XKLoader.. Open an Internet Explorer browser (version 6 or higher), a go to www.directechs.com. The detail of e platform a firmware at is currently saved on e interface module will be iicated in e top right corner of e page.. Select e year, make a model of e vehicle; e page will refresh to display e compatible firmware.. In e search result page, select Flash Staa inall, a follow e inructions provided on e screen. 5. Once you have configured your options, click on e FLASH button to upload e firmware onto e interface module. 6. The following message will be displayed when e upload is completed: The flashing is successfully completed. You may now unplug e kit. You can now proceed wi e programming inructions below. OR DD Inallation If required for your inallation, connect e 0-pin, -pin a -pin harnesses to e module, en connect e -pin DD harness. WW Inallation If required for your inallation, connect e 0-pin a -pin harnesses to e module, en connect e -pin harness to e module. DD 0-pin DD 0-pin -pin -pin -pin -pin Wait until e LED turns ON solid red. Solid Turn e key to art e vehicle. Key IN OFF IGN START The green LED turns ON for secos a shuts off. Solid x secs & Off 5 Remove e key from ignition. Key OUT OFF IGN START You have successfully completed e module programming sequence.
Platform: DBALL/DBALL Firmware: GM Module Reset Rev.: 050 Page 5 A module reset will only erase programming performed in e previous eps. All settings (firmware) a settings flashed to e module using e web config tool will not be affected. OR DD Inallation If required for your inallation, connect e 0-pin, -pin & -pin harnesses to e module. Press a hold e programming button, en connect e -pin DD harness. WW Inallation If required for your inallation, connect e 0-pin & -pin harnesses to e module. Press a hold e programming button, en connect e -pin harness to e module. 5 DD 0-pin DD 0-pin -pin -pin -pin -pin Wait secos until e LED turns ON solid orange en release e programming button. The LED en turns ON solid red. & & Solid Release Solid Ha Reset Warning Again Executing a Ha Reset! A ha reset will revert e flashed firmware back to its default settings. Depeing on e inallation, some settings (such as RFTD a DD options) may have to be reconfigured. See e Feature & Option Li section of is guide. OR DD Inallation If required for your inallation, connect e 0-pin, -pin & -pin harnesses to e module. Press a hold e programming button, en connect e -pin DD harness. WW Inallation If required for your inallation, connect e 0-pin & -pin harnesses to e module. Press a hold e programming button, en connect e -pin harness to e module. 5 DD 0-pin DD 0-pin -pin -pin -pin -pin Wait secos until e LED turns ON solid orange, a wait 0 more secos until e LED arts to flash orange a red. Solid & Release e programming button. The LED turns ON solid red. Release & Solid
Platform: DBALL/DBALL Firmware: GM Feature a Option Li Rev.: 050 Page 6 It is recommeed to configure all e features a options lied below using e configuration tool fou on e module flashing page on www.directechs.com. The web offers more options; however, manual configuration of e features is possible using e information on is page. * Default Option Feat. Operation /Option Description RFTD Output Type Unlock Driver Priority Heated Seats Heated Seats Temperature Control. No RF Output * Module is connected to a remote arter using a aa inallation.. RFTD Output Module is connected to an XL0 using an RSR or RXT inallation (when available).. SmartStart Module is connected to SmartStart using an RSR or RXT inallation (when available).. Driver Priority * Unlocks only e driver door on fir press a unlocks all doors on a seco press wiin 5 secos.. All Unlocks all doors on fir press.. Disabled * No operation.. Enabled It will activate e Heated Seats Control feature (see feature #5).. F (0 C) * When feature # is enabled, it will activate e heated seats upon remote art when temperature is below F (0 C).. F (-5 C) When feature # is enabled, it will activate e heated seats upon remote art when temperature is below F (-5 C).. F (5 C) When feature # is enabled, it will activate e heated seats upon remote art when temperature is below F (5 C).. Always ON When feature # is enabled, it will activate e heated seats at any temperature. 5 Heated Seats Temperature Level.High When Heated Seats are activated, ey will be set to HIGH.. Low * When Heated Seats are activated, ey will be set to LOW.. Disabled. Safelock The OEM alarm will not be controlled by DBALL upon remote art. No disarm or arm comma will be executed at e beginning or e of e sequence; it mu be controlled by e Remote Starter. Smart OEM Alarm Control will behave like a aa Safelock feature on a remote arter. It will unlock at e beginning of e sequence, a relock after art a shutdown. 6 Smart OEM Alarm Control. Enabled * Smart OEM Alarm Control will synchronize wi e OEM alarm so at it will disarm a rearm e vehicle in e remote art sequence, only when required. The reason for is is, factory alarm control mu often be done by lock or unlock operation. This could create unnecessary actions on door lock modules, such as e horn to honk. When possible, Smart OEM Alarm Control will monitor e alarm a door lock atus to detect if e disarm or rearm is required. If e vehicle is unlocked or is not equipped wi factory alarm, e disarm/rearm will not be executed. Smart OEM Alarm Control will also monitor e remote arter actions so at e factory alarm control is not done twice. A remote arter, for which e Safelock feature is active, will work perfectly wi is option a will make it invisible to e user.
Platform: DBALL/DBALL Firmware: GM Rev.: 050 Feature Programming To enter feature programming routine - Turn e ignition ON, en OFF. - Wiin 5 secos, press a HOLD e programming button until e LED turns ON orange (after secos). Release e Programming button. - The LED will flash green once slowly to iicate e feature number is. After a short delay, e LED flashes red rapidly to iicate e current option of feature (i.e. x green followed by x red iicates feature is set to option ). The flashing sequence will repeat until a new comma is entered. Changing feature options - Press e lock/arm or unlock/disarm button on aftermarket transmitter to change e option of e selected feature. - The LED flashes red rapidly e number of times equal to e current option number. After a short delay, e LED flashes green slowly e number of times to iicate e current feature. The flashing sequence will repeat until a new comma is entered. Accessing anoer feature - Press a release e programming button a number of times to advance from e current feature to e next desired feature. - The LED flashes green slowly e number of times equal to e feature number. After a short delay, e LED flashes red rapidly to iicate e current option of e current feature. The flashing sequence will repeat until a new comma is entered. When e maximum number of features or options is reached, e LED will art flashing again from e fir feature or option. Once a feature is programmed - Oer features can be programmed. - The feature programming can be exited. Programming Button Exiting feature programming - No activity for 0 secos; after 0 secos, e LED will turn ON orange for secos to confirm e e of e programming sequence. OR - Press a HOLD e programming button for secos. After secos, e LED will turn ON orange for secos to confirm e e of e programming sequence. Page 7
Platform: DBALL/DBALL Firmware: GM LED Diagnoics a Troubleshooting Rev.: 050 Page 8 LED Status Description Troubleshooting Module Programming Solid red green x secs Solid red. Solid green for secos. Module Programming - Error Codes Waiting for e vehicle to be arted. Module has been successfully programmed. Make sure at all e connections are correct (see wiring diagram) a art e vehicle to begin e programming sequence. Normal operation. Solid red x red times Bypass data has not been detected. Check e bypass line connection. If more an one wire is used, make sure ey are not inverted. External Module Synchronisation red & orange x0 red, red en orange 0 times OBDII feature is not supported. Diagnoic data bus not detected. Active Grou While Running green green Grou out (GWR) is active. Oerwise, e Grou While Running (atus) signal was lo or was never received by e module. red & orange red & orange IGNITION ON comma received. Oerwise, e ignition signal was not received by e module. green quickly green quickly START ON comma received. Oerwise, e art signal was not received by e module. Inactive Grou While Running green x green once LOCK comma received. green x green x green twice green times UNLOCK comma received. TRUNK comma received. If it does not flash, e bypass module did not receive e signal. Verify e connections between e bypass a e remote arter module. green x6 green 6 times AUX comma received.
Platform: DBALL/DBALL Firmware: GM Limited One Year Consumer Warranty Rev.: 050 Page 9 For a period of ONE YEAR from e date of purchase of a Directed Electronics remote art or security product, Directed Electronics. ( DIRECTED ) promises to e original purchaser, to repair or replace wi a comparable recoitioned piece, e security or remote art accessory piece (hereinafter e Part ), which proves to be defective in workmanship or material uer normal use, provided e following coitions are met: e Part was purchased from an auorized DIRECTED dealer; a e Part is returned to DIRECTED, poage prepaid, along wi a clear, legible copy of e receipt or bill of sale bearing e following information: consumer s name, address, telephone number, e auorized licensed dealer s name a complete product a Part description. This warranty is nontransferable a is automatically void if e Part has been modified or used in a manner contrary to its inteed purpose or e Part has been damaged by accident, unreasonable use, neglect, improper service, inallation or oer causes not arising out of defect in materials or conruction. TO THE MAXIMUM EXTENT ALLOWED BY LAW, EXCEPT AS STATED ABOVE, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NONINFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING DEALERS OR INSTALLERS. DIRECTED IS NOT OFFERING A GUARANTEE OR INSURANCE AGAINST VANDALISM, DAMAGE, OR THEFT OF THE AUTOMOBILE, ITS PARTS OR CONTENTS, AND DIRECTED HEREBY DISCLAIMS ANY LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE, OR VANDALISM. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER S PURCHASE PRICE OF THE PART. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR AT DIRECTED S OPTION THE PART AS DESCRIBED ABOVE. This warranty only covers Parts sold wiin e United States of America a Canada. Parts sold outside of e United States of America or Canada are sold AS-IS a shall have NO WARRANTY, express or implied. Some ates do not allow limitations on how long an implied warranty will la or e exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights a you may also have oer rights at vary from State to State. DIRECTED does not a has not auorized any person or entity to create for it any oer obligation, promise, duty or obligation in connection wi is Part. For furer details relating to warranty information of Directed products, please visit e support section of DIRECTED s website at: www.directed.com 90-00-0 0-07 This Interface kit / Data Bus Interface part has been teed on e lied vehicles. Oer vehicles will be added to e select vehicle li upon completion of compatibility teing. Visit website for late vehicle application guide. DISCLAIMER: Uer no circumances shall e manufacturer or e diributors of e bypass kit / data bus interface part(s) be held liable for any consequential damages suained in connection wi e part(s) inallation. The manufacturer a it s diributors will not, nor will ey auorize any representative or any oer iividual to assume obligation or liability in relation to e interface kit / data bus interface part(s) oer an its replacement. N.B.: Uer no circumances shall e manufacturer a diributors of is product be liable for consequential damages suained in connection wi is product a neier assumes nor auorizes any representative or oer person to assume for it any obligation or liability oer an e replacement of is product only. Protected by U.S. Patents: 5,79,55; 6,0,60 B *; 6,,00 B; 6,9,6 B; 6,75,7 B; 6,97,7 B; 6,6,876 B; 6,9,5 B; 6,59, B; 6,696,97 B; 6,756,885 B; 6,756,886 B; 6,77,67 B; 6,8,89 B; 6,9,750 B; 7,00,0 B; 7,05,80 B; 7,0,86 B; 7,06,6 B; 7,06,7 B; 7,068,5 B; 7,05,679 B; Cdn. Patent:,0,8;,,99;,5,0;,5,0;,5,07;,5,08;,5,0;,0,97;,6,670;,5,089; European Patent:,05,8; Pat. Peing:,9,06. Made in Canada.
Quick Reference Guide DBALL/DBALL-GM Li of Available Commas Notes Note at e information below is for Viper, Cliffo a Pyon models. Icons a commas may differ depeing on e remote bra a model purchased. Refer to your auorized inallation center for more information. Button(s) Actions Press & hold for seco to lock. Press & hold for seco to unlock. Press & hold for seco to remote art. Press & hold for 5 secos to activate e trunk release (optional). x + x + x + Press once, en to activate e rear hatch/tail glass release (optional).* Press times, en to activate e panic mode. Press once, en to reset e remote arter runtime. * This output is configurable. see your auorized inallation center for more information.