CABLE PULLERS CABLEGLIDER. CableGlider STD Typical Applications

Transcription

1 CableGlider STD Cable Puller The Condux CableGlider STD Cable Puller offers portability and ease of set-up in a completely self-contained unit to adapt to a variety of pulling situations. It comes equipped with a two-speed removable power pack, providing up to 6,500 pounds (28,912 N) of pulling force at low speed. Speed changes are no problem with just a turn of a dial. Design features include a self-tailing capstan for added stability, a pivoting arm and a foot switch for operator convenience and safety. Accepts all diameter rope (self-tailing capstan accepts 5 8" (16 mm) to 7 8" (22 mm) rope only). CableGlider STD includes the following items: Puller Foot switch Retaining Fork Conduit Adapters - 2" (51 mm), 3" (76 mm), 3 1 2" (89 mm), 4" (102 mm) Tool box for the accessories CableGlider STD Typical Applications ft (2 m) PIVOTING ARM VERTICAL (UP) PULL FROM FLOOR VERTICAL (DOWN) PULL FROM BOX 82 TOLL-FREE (US & Canada) TEL FAX

2 CableGlider STD Volt Standard Cable Puller* S 110 Volt Standard Cable Puller Split* *(International orders must specify plug type) WARNING: CableGlider Cable Pullers are not to be used as a hoist or for lifting, supporting or transporting people or loads. Complete Pulling Packages For CableGlider STD Condux pulling packages offer cost savings and ordering convenience. Part No. Description CableGlider STD (Package 1) S CableGlider STD (Package 1) Split 110 Volt Puller with accessories (above) Standard Extension Frame (pg. 90) 600 ft. (183 m) of 5 8" (16 mm) double-braided rope (pg. 43) Floor/Conduit/Pole Mount Frame (pg. 89) 5" (127 mm) & 6" (152 mm) adapters w/retaining fork (pg. 91) Running Line Tensiometer with Chart Recorder (pg. 92) CableGlider STD (Package 2) S CableGlider STD (Package 2) Split All items in package 1 with: Amp-type Tensiometer (pg. 91) (replaces RLT) Transformer Volt Converter 4000 Watt Used only with the STD and Plus CableGliders. Features: 4000 Watt Heavy-Duty Continuous use Transformer One grounded outlet in front of unit (accepts 3 or 2 prong US and Euro plugs) Converts 220/240 Volts down to 110/120 Volts Built-In Fuse Protection Hard-Wire with European Shucko Plug also good for Asian Outlets Transformer Volt Converter 4000 Watt CableGlider STD Package 1 SPECIFICATIONS Low Speed High Speed PULLING FORCE lbs kn lbs kn Maximum 6, , Continuous 4, , PULLING SPEED ft/min m/min ft/min m/min No Load At 2,000 lbs (8.9 kn) At 4,000 lbs (17.8 kn) At 6,000 lbs (26.7 kn) Power Requirements Amps Min. PEAK POWER 1.9 HP (1.42 kw) GENERATOR 4000 Watt Recommended* *NOTE: Use of less than the recommended wattage generator may effect the pulling specifications listed above. CableGlider STD Typical Applications HORIZONTAL PULL HORIZONTAL VAULT PULL VERTICAL PULL WITH 45 ELBOW TOLL-FREE (US & Canada) TEL FAX

3 CableGlider Plus Cable Puller This model comes equipped with the same removable two-speed, 6,500 lbs (28,912 N) power pack and accessories as our STD model, but features a heavy-duty frame with an extra pivoting arm for added performance and versatility. In addition, the front frame height can easily be adjusted with pins. Like all CableGlider models, the Plus is portable, sets up quickly and comes completely self-contained, ready to work. As with the STD model, the CableGlider Plus features a self-tailing capstan for added stability, a pivoting arm and a foot switch for operator convenience and safety. Accepts all diameter rope (self-tailing capstan accepts 5 8" (16 mm) to 7 8" (22 mm) rope only). CableGlider Plus includes the following items: Puller Foot switch Retaining Fork Conduit Adapters - 2" (51 mm), 3" (76 mm), 3 1 2" (89 mm), 4" (102 mm) Tool box for the accessories CableGlider Plus CableGlider Plus Typical Applications TRANSPORT POSITION FIRST PIVOTING ARM SECOND PIVOTING ARM 84 TOLL-FREE (US & Canada) TEL FAX

4 CableGlider Plus Volt Plus Cable Puller* S 110 Volt Plus Cable Puller Split* *(International orders must specify plug type) WARNING: CableGlider Cable Pullers are not to be used as a hoist or for lifting, supporting or transporting people or loads. Complete Pulling Packages For CableGlider Plus Condux pulling packages offer cost savings and ordering convenience. Part No. Description CableGlider Plus (Package 1) S CableGlider Plus (Package 1) Split 110 Volt Puller with accessories (above) HD Extension Frame (pg. 90) 600 ft. (183 m) of 5 8" (16 mm) double-braided rope (pg. 43) Floor/Conduit/Pole Mount Frame (pg. 89) 5" (127 mm) & 6" (152 mm) adapters w/retaining fork (pg. 91) Running Line Tensiometer w/data recorder (pg. 93) CableGlider Plus (Package 2) S CableGlider Plus (Package 2) Split All items in package 1 with: Amp-type Tensiometer (pg. 91) (replaces RLT) CableGlider Plus Package 1 SPECIFICATIONS Low Speed High Speed PULLING FORCE lbs kn lbs kn Maximum 6, , Continuous 4, , PULLING SPEED ft/min m/min ft/min m/min No Load At 2,000 lbs (8.9 kn) At 4,000 lbs (17.8 kn) At 6,000 lbs (26.7 kn) Power Requirements Amps Min. PEAK POWER 1.9 HP (1.42 kw) GENERATOR 4000 Watt Recommended* *NOTE: Use of less than the recommended wattage generator may effect the pulling specifications listed above. CableGlider Plus Typical Applications 10 ft (3 10 m) ft (3 m) VERTICAL OVERHEAD PULL HORIZONTAL PULL OVER OBSTRUCTION HORIZONTAL VAULT PULL TOLL-FREE (US & Canada) TEL FAX

5 CableGlider HD Cable Puller The Condux CableGlider HD is specially designed to provide maximum pulling power for longer runs in a completely self-contained unit. It offers fast set-up, portability and is easily adaptable for a variety of pulling situations. The removable power pack delivers up to 12,000 pounds (53,375 N) of pulling force at low speed over 80% more than our STD puller. The two-speed motor pulls up to 30 feet per minute at high speed and up to 15 feet per minute at low speed. The CableGlider HD comes with a heavy-duty frame and extra pivoting arm. The front frame height can easily be adjusted with pins. CableGlider HD includes the following items: Puller Foot switch Retaining Fork Conduit Adapters - 2" (51 mm), 3" (76 mm), 3 1 2" (89 mm), 4" (102 mm) Tool box for the accessories CableGlider HD Typical Applications TRANSPORT POSITION FIRST PIVOTING ARM SECOND PIVOTING ARM 86 TOLL-FREE (US & Canada) TEL FAX

6 CableGlider HD Volt HD Cable Puller with 20 amp twist plug* S 110 Volt HD Cable Puller with 20 amp twist plug Split* *(International orders must specify plug type) WARNING: CableGlider Cable Pullers are not to be used as a hoist or for lifting, supporting or transporting people or loads. Complete Pulling Packages For CableGlider HD Condux pulling packages offer cost savings and ordering convenience. Part No. Description CableGlider HD (Package 1) S CableGlider HD (Package 1) Split 110 Volt Puller with accessories (above) HD Extension Frame (pg. 90) 600 ft. (183 m) of 7 8" (22 mm) double-braided rope (pg. 43) Floor/Conduit/Pole Mount Frame (pg. 89) 5" (127 mm) & 6" (152 mm) adapters w/retaining fork (pg. 91) Running Line Tensiometer w/data recorder (pg. 93) CableGlider HD (Package 2) S CableGlider HD (Package 2) Split All items in package 1 with: Amp-type Tensiometer (pg. 91 ) (replaces RLT) CableGlider HD Package 1 SPECIFICATIONS Low Speed High Speed PULLING FORCE lbs kn lbs kn Maximum 12, , Continuous 6, , PULLING SPEED ft/min m/min ft/min m/min No Load At 4,000 lbs (17.8 kn) At 6,000 lbs (26.7 kn) At 10,000 lbs (44.5 kn) Power Requirements Amps Min. PEAK POWER 4.7 HP (3.50 kw) GENERATOR 8000 Watt Recommended* *NOTE: Use of less than the recommended wattage generator may effect the pulling specifications listed above. CableGlider HD Typical Applications 10 ft (3 m) VERTICAL OVERHEAD PULL HORIZONTAL PULL OVER OBSTRUCTION HORIZONTAL VAULT PULL TOLL-FREE (US & Canada) TEL FAX