ENGLISH P17921E FEBRUARY 2012 OPERATORS MANUAL & PARTS LIST UNIPRESS

Transcription

1 ENGLISH P17921E FEBRUARY 2012 OPERATORS MANUAL & PARTS LIST UNIPRESS

2 ENG If you require a copy of this document in your native language please contact your dealer or Simba Great Plains. CZE Požadujete-li kopii tohoto dokumentu ve svém rodném jazyce, obraťte se prosím na svého prodejce nebo na společnost Simba Great Plains. HUN Ha szeretné ezt a leírást magyarul is megkapni, kérjük, értesítse a forgalmazóját vagy a Simba Great Plains-t. FRA Pour obtenir un exemplaire du présent document dans la langue de votre choix, veuillez contacter votre représentant ou Simba Great Plains. LIT Jei prireiktų šio dokumento kopijos Jūsų gimtąja kalba, kreipkitės į savo platintoją arba į Simba Great Plains. BUL Ако ви е необходимо копие на този документ на родния ви език, моля да се обърнете към вашия дилър или към Simba Great Plains. RUM Dacă aveţi nevoie de o copie a acestui document în limba dumneavoastră natală vă rugăm să vă contactaţi dealerul sau Simba Great Plains. RUS Чтобы получить копию данного документа на вашем родном языке, обратитесь к своему дилеру или в компанию «Simba Great Plains» GER Wenn Sie ein Exemplar dieses Dokuments in Ihrer Muttersprache brauchen, dann wenden Sie sich bitte an Ihren Händler oder an die Simba Great Plains.

3 Declaration of Conformity DECLARATION OF CONFORMITY Simba International Limited hereby declare that the Simba Great Plains, as defined by the Serial Number attached to the Machine Chassis, conforms with the following Directives and Regulations, and has been certified accordingly. EC Machinery Directive 2006/42/EC. The Supply of Machinery (Safety) Regulations The Provision and Use of Work Equipment Regulations Specifically related harmonised standards are: EN ISO : 2003 (Safety of Machinery). EN ISO : 2003 (Safety of Machinery). EN ISO : 2009 (Agricultural machinery - Safety - General Requirements). THE MANUFACTURER: Simba International Limited Woodbridge Road SLEAFORD Lincolnshire NG34 7EW England Telephone (+44) (0) CERTIFIED ON BEHALF OF SIMBA INTERNATIONAL LIMITED: Colin Adams Managing Director 3

4 Warranty WARRANTY TERMS AND CONDITIONS In this warranty Simba International Ltd., is referred to as the Company. 1. Subject to the provisions of this warranty the Company warrants each new machine sold by it to be sold free from any defect in material or workmanship for a period of 12 months from date of installation with the end-user. Some specific items have additional warranty over and above the standard 12 months. Details of these can be obtained upon request directly from the distributor or Simba International Ltd. 2. If the machine or part thereof supplied by the Company is not in accordance with the warranty given in clause 1 the Company will at its option: (a) (b) (c) make good the machine or part thereof at the Company s expense, or make an allowance to the purchaser against the purchase price of the machine or part thereof, or accept the return of the machine and at the buyers option either: I) repay or allow the buyer the invoice price of the machine or part thereof, or II) replace the machine or part thereof as is reasonably practical. 3. This warranty shall not oblige the Company to make any payment in respect of loss of profit or other consequential loss or contingent liability of the Purchaser alleged to arise from any defect in the machine or impose any liability on the Company other than that contained in clause Any claim under this warranty must be notified to the Company in writing specifying the matters complained of within 14 days from the date of repair. 5. Any claim under this warranty must be made by the original purchaser of the machine and is not assignable to any third party. 6. If the purchaser hires out the machine to any third party the warranty shall apply only to matters notified to the Company in writing within 90 days of the date of delivery and clause 1 shall be read as if the period of 90 days were substituted for the period of 12 months. 7. The warranty will cease to apply if: (a) (b) (c) (d) (e) (f) (g) (h) any parts not made, supplied or approved in writing by the Company are fitted to the machine or any repair is carried out to the machine other than by or with the express written approval of the Company or any alterations not expressly authorized by the Company in writing are made to the machine or the machine is damaged by accident or the machine is abused or overloaded or used for a purpose or load beyond its design capabilities, or used in conjunction with a tractor whose power output capability exceeds the stated implement power requirement by more than 40%. For the purpose of these terms and conditions, stated implement power requirement refers to wheeled tractors unless specifically stated. These power requirements should be reduced by 20% when used in conjunction with tracked tractors. the machine is operated as part of a cultivation train where more than one implement is being towed, without the express written approval of Simba International Ltd. any maintenance is not carried out in accordance with the service schedules in the operator s manual. the Installation and Warranty Registration Certificate is not received by Simba International Ltd., Service Dept., Woodbridge Road, Sleaford, Lincolnshire, England, NG34 7EW, within 7 days of installing a new machine. 4

5 Machine Identification Machine Identification Enter the relevant data in the following list upon acceptance of the machine: Serial Number Type of Machine Machine Width Year of Construction Delivery Date First Operation Accessories /Spare Parts List: February 2012 Dealer Address: Name: Street: Place: Tel.: Dealer s Customer No.: Simba Great Plains Address: Simba Great Plains Woodbridge Road Ind. Est. Sleaford Lincolnshire NG34 7EW Tel.: +44 (0) Fax: +44 (0) simba.international@simba.co.uk Simba Great Plains Customer No.: 5

6 Contents Contents Machine Identification...5 Introduction...8 Foreword...8 Warranty Guidelines Safety Data Safety Symbols Use for the Intended Purpose Operational Safety No Liability for Consequential Damage Road Traffic Safety Accident Prevention Hitching-up the machine On the Hydraulic System Changing Equipment During Operation Servicing & Maintenance Operating Areas Authorised Operators Protective Equipment Transportation and Installation Delivery Transportation Installation Hitching Up Hitching up a Tractor to the / Preparing for Transport Folding and Unfolding Unfolding into the Work Position Folding into the Transport Position Air Brake Coupling Procedure When Coupling When De-coupling Preceding and Trailing Implements Hitching a Disc Cultivator to the Transporting a Towed Behind a Disc Cultivator Changing from Work to Road Transport (Disc Cultivator Behind a ) Setting the Rear Drawbar Hitching a Rear Roll to the When driving on the road Parking the machine Technical Data

7 Contents 4. Adjustment/Operation Description Pro-Active (Sprung)Tines Levelling Boards Double Disc Roller Work Settings Levelling Boards Pitch Control Using Shims Work Instructions Checks Servicing and Maintenance Servicing Cleaning Double Disc Axles Hydraulics Tines Levelling Boards Preparation for Storage Operator Support Brakes & Wheel Hubs Maintenance Intervals To Adjust the System Pressure Maintenance Overview Lubricating the Machine Handling of Lubricants Lubricants & Hydraulic Oil Faults and Remedies Parts & Assembly

8 Introduction Introduction Foreword Make sure you have read and follow the carefully before using the machine. By doing so, you will avoid accidents, reduce repair costs and downtime and increase the reliability and service life of your machine. Pay attention to the safety instructions! Simba Great Plains will not accept any responsibility for any damage or malfunctions resulting from failure to comply with the. These will assist you in getting to know your machine and in using it correctly for its intended purposes. First, you are given general instructions in handling the machine. This is followed by sections on servicing, maintenance and the action to be taken should a malfunction occur. We reserve the right to alter illustrations as well as technical data and weights contained in these for the purpose of improving the machine. Warranty Guidelines The period of liability for material defects (warranty) relating to our products is 12 months. In the case of written deviations from the statutory provisions, these agreements shall apply. They shall become effective upon installation of the machine with the end customer. All wear parts are excluded from the warranty. All warranty claims must be submitted to Simba Great Plains via your dealer. These operating instructions are to be read and followed by all persons working on or with the machine, e.g.: Operation (including preparation, remedying of faults in the operating sequence and servicing). Maintenance (maintenance and inspection) Transportation. Together with the, you receive a Spare Parts List and a Machine Registration form. Field service technicians will instruct you in the operation and servicing of your machine. Following this, the Machine Registration form is to be returned to your dealer. This confirms your formal acceptance of the machine. The warranty period begins on the date of delivery. 8

9 1. Safety Data 1. Safety Data The following warnings and safety instructions apply to all sections of these Operating Instructions. Parts may fly off during operation. Keep a safe distance away from the machine! 1.1 Safety Symbols On the machine Read and observe the Operating Instructions before using the machine! Keep clear of the working range of foldable machine components! Watch out for escaping pressurised fluids! Follow the instructions in the Operating Instructions! No passengers are allowed on the machine! Never reach into areas where there is a danger of being crushed by moving parts! Never reach into any revolving parts! 9

10 1. Safety Data R e f e r t o O p e r a t i n g I n s t r u c t i o n s b e f o r e attempting maintenance. : The distinguish between three different types of warning and safety instructions. The following graphic symbols are used: Important! Risk of injury! Risk of fatal and serious injuries! It is important that all the safety instructions contained in these and all the warning signs on the machine are read carefully. Ensure that the warning signs are legible. Replace any signs that are missing or damaged. These instructions must be followed in order to prevent accidents. Inform other users of the warnings and safety instructions. Do not carry out any operations which may affect safe use of the machine. All references to left and right in this manual are made from the rear of the machine, facing the direction of travel (unless otherwise stated). 10

11 1. Safety Data 1.2 Use for the Intended Purpose The Simba Great Plains is built using the latest technology and in accordance with the relevant recognised safety regulations. However, risks of injury for the operator or third parties and impairment of the machine or other tangible assets can arise during use. The machine is only to be operated when in a technically perfect condition and for the intended purpose, taking into consideration safety and risks and following the Operating Instructions. In particular, faults that can impair safety are to be remedied immediately. Original parts and accessories from Simba Great Plains have been specially designed for this machine. Spare parts and accessories not supplied by us have not been tested or authorised. Installation or use of non-original Simba Great Plains products may have a detrimental effect on specific design features of the machine and affect the safety of machine operators and the machine itself. Simba Great Plains will accept no liability for damage resulting from the use of non-original parts or accessories. The Simba Great Plains is designed solely as a cultivation implement. Use for any other purpose, e.g., as a means of transport, will be deemed to be improper use. Simba Great Plains will accept no liability for damage resulting from improper use. The risk will be borne solely by the operator. Use of the behind high power tractors (in excess of 40% above the maximum recommended) can lead to high loads and stresses which can cause long term structural damage to the chassis and key components. Such overloading can compromise safety and is to be avoided. 1.3 Operational Safety The machine is to be put in operation only after instruction has been provided by an employee of the authorised dealer or an employee of Simba Great Plains. The Machine Registration form is to be completed and returned to your dealer. All protective and safety equipment, such as removable protective equipment, must be in place and functioning reliably before the machine is put in use. Check screws and bolts regularly for tightness and retighten if necessary. In the event of malfunctions, stop and secure the machine immediately. Ensure that any faults are remedied immediately. 1.4 No Liability for Consequential Damage The has been manufactured with great care. However, problems may still occur when it is used for the intended purpose. These may include: Worn wearing parts. Damage caused by external factors. Incorrect driving speeds. Incorrect setting of the unit (incorrect attachment, non-adherence to the Setting instructions). Therefore, it is crucial to always check your machine before and during operation for correct operation and adequate application accuracy. Compensation claims for damage which has not occurred to the machine is excluded. This includes any consequential damage resulting from incorrect operation. 11

12 1. Safety Data 1.5 Road Traffic Safety When driving on public roads, tracks and areas, it is important to observe the relevant road traffic laws as well as the specific regulations relating to this machine. Pay attention to the permitted axle loads, tyre carrying capacity, and total weight in order to maintain adequate braking and steerability (these figures are shown on the serial plate). Passengers on the machine are strictly forbidden! Max. road transport speed 16mph (25km/h). 1.6 Accident Prevention In addition to the, it is important to observe the accident prevention regulations specified by agricultural trade associations. It is the Operator s responsibility to ensure that all other persons are excluded from the danger zones surrounding or on the machine during its operation. It is the Owner s responsibility to ensure: the Operator is trained and competent to use the machine & tractor, the tractor is suitable for the machine adequate Risk and COSHH assessments have been undertaken regarding the machine s use. Specifically, these include issues concerning contact with the soil, dust, crop residues, chemicals, lubricants and other compounds during operation or maintenance, and the possibility of stones being ejected at high speed during work. Beware of trapping hazards when manipulating the parking stands or other moving parts. Ensure any heavy components are fully supported when removing pins / bolts Hitching-up the machine There is a risk of injury when hitching/ unhitching the machine. Observe the following: Secure the machine against rolling. Take special care when reversing the tractor! There is a risk of being crushed between the machine and the tractor! Park the machine on firm, level ground On the Hydraulic System Do not connect the hydraulic lines to the tractor until both hydraulic systems (machine and tractor) are depressurised. Any hydraulic system containing an accumulator can remain under pressure permanently (even after following manual depressurisation procedures with a tractor / implement combination). It is therefore important to check all lines, pipes, and screw connections regularly for leaks and any recognisable external damage. The hydraulic circuit contains specialised fittings which should not be tampered with under any circumstances. Do not attempt to modify hose routings or hose clamping arrangements, doing so my cause serious damage to the machine and/or injury. 12

13 1. Safety Data Only use appropriate aids when checking for leaks. Repair any damage immediately. Spurting oil can cause injuries and fires! In case of injury, contact a doctor immediately. The socket and plugs for the hydraulic connections between the tractor and the machine should be colour-coded in order to avoid incorrect use. Do not stand on the machine while it is in operation! Operators must have a valid driving licence in order to drive on public roads. In the operating area, the operator is responsible for third parties. The person in charge must: provide the operator with a copy of the, and ensure that the operator has read and understood the instructions. Fig. 1.01: HydraulicTaps Changing Equipment Secure the machine to prevent it from accidentally rolling away! Use suitable supports to secure any raised frame sections suspended above you! Caution! Risk of injury due to projecting parts! Never climb on to rotating parts such as the roll unit. These parts may rotate causing you to slip and suffer serious injury! Removing components during maintenance may affect the stability of the machine. Ensure it is fully supported in case of unexpected weight shifts During Operation Ensure that the working range and the area around the machine are clear (children!) before operating the machine. Always ensure adequate visibility! make sure that the operator is aware of the specific regulations relating to the machine when driving on public roads. 1.7 Servicing & Maintenance Ensure that regular checks and inspections are always carried out within the periods required by law or specified in these. When carrying out service and maintenance work always: switch off the tractor engine and remove the ignition key. wait until all the machine parts have stopped moving. depressurise the hydraulic system. Many hydraulic circuits contain lock or overcentre valves which can retain pressure in the lines even after depressurising the tractor side of these circuits. If in doubt, consult trained personnel (such as your local Simba Great Plains Dealer) to ensure such valves are depressurised to the correct procedure before removing or servicing any parts connected downstream of these valves. 13

14 1. Safety Data Check all hydraulic lines for leaks, loose connections, chafe marks and damage. Remedy any deficiencies immediately! Pay particular attention to hose renewal intervals as outlined in the specific sections which follow. ALL hydraulic hoses have a safe maximum working life of 6 (SIX) years from date of installation, provided they remain in a safe condition. Hoses which exceed 6 years of age should be replaced, or inspected and certified by a suitably qualified person to have an extended life period which should be recorded. Pay particular attention to those items which require specialist service tools or training to be carried out by qualified personnel. Do not attempt to service these items yourself! These include items retaining pressure (e.g. accumulator circuits), or force (e.g. spring tines), and DD Rolls of any type. Prior to performing maintenance and servicing work, ensure that the machine is positioned on solid, level ground and is secured to prevent it rolling away. Do not use any parts to climb on to the machine unless they are specifically designed for this purpose. Before cleaning the machine with water, steam jets (high-pressure cleaning apparatus) or other cleaning agents, cover all openings into which, for reasons of safety or operation, no water, steam or cleaning agents are to penetrate (bearings, for instance). Lubricate all the lubricating points to force out any trapped water. When carrying out servicing and maintenance work, retighten any loose screw connections. On a new machine tighten all nuts and bolts after 5 hours work and again after 15 hours. This also applies to parts that have been moved or replaced. After the initial 15 hours of work a once a week check should be sufficient depending on daily work rates. 1.8 Operating Areas The operating areas include the drawbar, hydraulic connections and depth adjustment equipment as well as all operating points requiring maintenance. All operating areas will be specified and described in detail in the following chapters on servicing and maintenance. Observe all safety regulations included in the section dealing with Safety, and in the subsequent sections. 1.9 Authorised Operators Only those persons who have been authorised and instructed by the operator may operate the machine. The operator must be at least 16 years of age Protective Equipment For operation and maintenance, you require: Tight fitting clothing. Strong protective gloves (to provide protection against sharp-edged machine components). Protective goggles (to stop dirt getting into your eyes). When servicing the machine take precautions against soil, dust, seed coatings, oil or any other hazardous substances that you might encounter. 14

15 2. Transportation / Installation 2. Transportation and Installation Transportation and initial installation of the machine are described in this chapter. 2.1 Delivery The machine is normally delivered fully assembled. The machine can be lifted off with a crane or other suitable lifting equipment. The machine should be hitched to a tractor and driven off a low-loader. 2.2 Transportation The can be transported on public roads by hitching it up to a tractor or on a low-loader. It is important to observe the permitted d i m e n s i o n s a n d w e i g h t s w h e n transporting the machine. If the machine is transported on a trailer or a low-loader, it must be secured using straps or other devices. 2.3 Installation When carrying out installation and maintenance work there is a higher risk of injury. It is important that you familiarise yourself with the machine and read the beforehand. Operator instruction and initial installation of the machine are carried out by our service technicians or authorised distributors. The machine must not be used in any way beforehand! The machine can only be released for operation after instructions have been provided by our service technicians or authorised distributors. If any modules or parts have been removed for transportation, these shall be mounted by our service technicians/ authorised dealers before the instruction takes place. Check all important screw connections! Lubricate all nipples and joints! Check all hydraulic connections and lines for damage. Before transporting the machine on public roads, it must be adjusted to its transportation position and the stipulations relating to road transportation fulfilled. The maximum permissible speed is 25 km/h. 15

16 2. Transportation / Installation 2.4 Hitching Up When hitching-up the machine, ensure that no-one is between the tractor and the machine. When the is parked for extended periods of time it should ideally be left in the unfolded, i.e. work, position for stability, safety and ease of access for maintenance. However, parking the in the folded position (using the parking stands provided) is acceptable in the normal course of operation. Tractor Oil Flow Adjustment: As a general rule the tractor oil flow rate should be set in the lowest setting before starting. This can then be increased to allow the desired rate of operation as applicable. This will minimise excessive oil flow and consequent power usage and heat generation. Do not open taps while tractor hydraulics are in float. The hoses in the lift circuit have a maximum rated pressure of 415bar, and should be replaced every 6 years. Other components in this locking circuit have a maximum rated pressure of at least 350bar Hitching up a Tractor to the / Preparing for Transport 1. Couple the six hydraulic hoses to the tractor ensuring that the two wing hoses are together, the two drawbar cylinder hoses are together and the two levelling board hoses are together. 2. Connect the tractor to the drawbar using the hydraulics to raise or lower the height of the shackle. Do not use the tractor pick-up hitch to attach the machine to the tractor. 3. Carefully operate the hydraulics to lower the drawbar and tilt the onto the road transport wheels. Fully extend the drawbar cylinder. 4. This allows the levelling boards to be fully raised so that when the is folded the levelling boards do not protrude beyond the 3m transport width. Fully raise the levelling boards. 5. Operate the hydraulics to fold the wings. 6. Ensure that the wing strap is fitted to tie the two wing sections together. 7. Ensure that parking stands are locked in the transport position, ie. fully raised. 16

17 2. Transportation / Installation 2.5 Folding and Unfolding Check for exposed persons when lowering / unfolding the machine. Do not climb on the machine to fit or remove the transport strap, this should be done from the ground Unfolding into the Work Position 1. Ensure that the parking stands are in the fully raised position. 2. Remove the transport strap from the rear wing cylinders. Stow the transport strap on the lights as shown in Fig Folding into the Transport Position 1. Fully raise the levelling boards so that they do not protrude beyond the 3m transport width. 2. Raise the machine onto the transport wheels. 3. Operate the hydraulics to fully fold the wings. 4. Fit the transport strap across the pins on the rear wing cylinders for transport safety. 5. Close the taps on the hosemast. 6. Lower the parking stands if the is to be unhitched from the tractor in the folded position. 3. Open the taps on the hosemast. Beware of sudden or uncontrolled movements if the taps are opened with the hydraulics in float. Do not open taps with the tractor hydraulics in float. Fig. 2.01: Transport Strap Stowage in Work 4. Operate the hydraulics to fully unfold the wings. 5. Lower the machine to the ground until the chassis is level front to rear or the drawbar cylinders touch the depth stops. 17

18 2. Transportation / Installation 2.6 Air Brake Coupling Procedure Please refer to the following procedure when coupling or decoupling any item of Simba Great Plains machinery fitted with an AIR brake or AIR and HYDRAULIC brake system. Please note that this procedure does not apply to any machines fitted with a HYDRAULIC system ONLY. 4. Continue de-coupling the machine until it is fully disconnected. By following the above instructions you will see that at NO point in the coupling or decoupling process has the red line been left in the tractor on its own. This is intentional and should be considered the rule to coupling the hoses When Coupling 1. Reverse up to the machine and connect the machine to the tractor as instructed to in Section With the machine connected couple the air lines. When coupling ensure the yellow line is attached first followed by the red line. 3. Your brake hoses are now attached and are ready for operation. 4. Continue with the coupling process as instructed in Section When De-coupling 1. Bring the machine to the parking position as instructed to in Section With the machine still connected to the tractor remove the red brake line followed by the yellow line. 3. Your brakes will now be ON and will hold, ensuring they have been adjusted and maintained correctly, the machine in position. (note: if the machine s tank is drained of air once all lines have been detached the brakes will come off (same situation as pushing the shunt valve). 18

19 2. Transportation / Installation 2.7 Preceding & Trailing Implements Adding a preceding or trailing implement to the will affect the stability and handling of the machine both in transport and work Hitching a Disc Cultivator Ahead of the 1. Remove the transport straps from the disc cultivator, exercise great CARE when extending the axle cylinder. 2. Reverse the disc cultivator up to the drawbar ensuring that the two drawbars are aligned allowing a slight clearance to enable the machines to be coupled together. 3. Lower the disc cultivator to the ground. 4. Connect the hydraulic hoses from the into the disc cultivator rear outlets ensuring that the wing hoses are together and the drawbar cylinder hoses are together. Ensure that the folding circuits and lift drawbar circuits are coupled correctly. 8. Operate the hydraulics to lower the rear axle and drawbar, tilting the onto the road transport wheels. Fully extend the drawbar cylinders. 9. Fully raise the levelling boards. 10. Operate the hydraulics to fold the wings. 11. Operate the hydraulics to lift the disc cultivator into the transport position. 12. Fit the disc cultivator transport straps. 13. Fit the wing transport strap to tie the two wing sections together. 14. Ensure that parking stands are locked up in their work position. With both machines in the transport position i.e. raised and folded, the chassis of the disc cultivator should be slightly nose down or horizontal even when the downward load from the is applied to the drawbar of the disc cultivator. The frame may be levelled by altering the rearward tilt of the to increase or reduce the loading on the disc rear drawbar. 5. Raise the drawbar above the disc drawbar (200mm approx.). Depth control shims may need to be removed. 6. Raise the disc cultivator to the same height as the drawbar then reverse the disc cultivator to couple the two machines together. 7. Fit the drawbar pin. 19

20 2. Transportation / Installation Transporting a Towed Behind a Disc Cultivator With both machines in the transport position i.e. raised and folded, the chassis of the disc cultivator should be slightly nose down or horizontal even when the downward load from the is applied to the drawbar of the disc cultivator. The chassis should NEVER be tail low in transport as this will give a high negative loading on the tractor which could lead to loss of traction to the rear wheels. Extreme caution must be taken when the is transported up steep gradients and across side slopes. Higher drawbar loading can be achieved by shortening the drawbar cylinder. Shortening the drawbar cylinder will increase the loading on the rear of the disc cultivator frame. If necessary this can be used to level the chassis for road transport Rear Drawbar Setting To prepare the rear drawbar for use: 1. Open the tap on the rear drawbar cylinder. 2. Retract the cylinder and insert pin. 3. Close the tap to secure its position. STOWAGE HOLE Prior to leaving the field to travel on a public highway ensure that any clods of soil are removed from the machine to prevent them from fouling the road. TAP (SHOWN OPEN) PIN MAXIMUM ROAD TRANSPORT SPEED 16 MPH (25 km/h) Changing from Work to Road Transport ( Towed Behind a Disc Cultivator) 1. Operate the hydraulics to raise the disc and. 2. Operate the hydraulics to fold the wings on both the disc cultivator and the. Fig. 2.02: Rear Drawbar position when in use To change back to road transport / 'not in use' position: 1. Open the tap on the rear drawbar cylinder. 2. Remove the pin and stow in the hole shown. 3. Extend the cylinder and close the tap to secure its position. 3. Fit the transport straps to both machines. It may be necessary to shorten the drawbar cylinder of the disc cultivator until the chassis is horizontal or slightly nose down before moving the machines. Fig. 2.03: Rear Drawbar position when not in use 20

21 2. Transportation / Installation Hitching a Rear Roll to the Follow procedure 2.4 (page 16) to couple a tractor to the. Once the tractor is safely connected to the implement and in its folded setting, raise the machine fully clear of the ground. Maximum rear drawbar vertical loading = 650kg 1. Reverse the up to the roller. 2. Align the and roller drawbars, lower the to the ground and depressurise the lift hydraulics. 3. Raise / lower the axle as required to align the respective machines drawbars and couple together. 4. Couple the rear roll to the lift circuit of the, ensuring that the hoses are connected to the corresponding circuit on the trailing machine. 2.9 Parking the machine In order to avoid damage as a result of moisture, the machine should be parked, if possible, indoors or under cover. When manoeuvring the machine, pay attention to your surroundings. Ensure that nobody is in the manoeuvring area (watch for children!). Park the machine on level and solid ground. Fit wheel chocks. With the machine raised move the parking stands into position. Lower the machine onto the parking stands ensuring that it is stable. Remove the drawbar pin and drive forward slowly until hitch is clear of tractor drawbar. Lower the drawbar to the ground. Switch off the tractor. Disconnect hydraulic lines from the tractor. If parking on uneven or sloping ground chock the machine and unfold / lower first to avoid instability. 5. Couple the rear roll wing (fold) circuit to the wing (fold) circuit of the. 6. Fully raise the and the roll clear of the ground. 7. Check that all transport straps / devices are fitted or closed. 2.8 When driving on the road When driving on the road the machine must be converted to the transportation position. Fig Wheel chocks When driving on the road, raise the machine completely to prevent the working elements dragging on the ground. 21

22 2. Transportation / Installation 22

23 3. Technical Data 3. Technical Data 4.6m 5.5m 6.6m 7.2m 8.2m Working Width 4600mm 5500mm 6600mm 7200mm 8200mm Transport Width 2950mm 2950mm 2950mm 2950mm 2950mm Transport Height 2820mm 3145mm 3925mm 3970mm 4417mm Transport Length 5125mm 5180mm 5125mm 5350mm 5500mm Weight 4246Kg 4775Kg 5276Kg 6135Kg 6638Kg Tractor Power Req.(Hp)* Drawbar Load ** 1150Kg 1233Kg 1235Kg 1433Kg 1492Kg Axle Load 3096Kg 3542Kg 4041Kg 4702Kg 5146Kg * It is important to correctly match your implement to your tractor for optimum performance. ** Varies with lift, tilt and options. 23

24 4. Adjustment / Operation 4. Adjustment/Operation 4.1 Description Fig. 4.01: 4 1. Drawbar 2. Shim Stowage 3. Parking Stands 4. Tines 5. Levelling Board 6. DD700 Roll 7. Transport Wheels 8. Wheel Chocks 9. Rear Drawbar (if fitted) 10. Hydraulic Hose Stowage 3 The Simba Great Plains is a versatile implement designed to perform an excellent shallow cultivation combined with effective consolidation. The may be towed on its own or in tandem behind another implement e.g. disc cultivator. It can be used in reduced tillage systems behind a disc cultivator to incorporate stubble or to work down ploughing on medium to heavy soil types. Like all Simba Great Plains machines it features the latest innovations which combine to give an efficient, well-built unit with unrivalled reliability. 2 1 The consists of two rows of sprung tines followed by a hydraulically operated levelling board then a row of press rings. The levelling board consists of a series of sprung leaves with each leaf set between each roll ring. The levelling board carries soil ahead of the rings to fill low areas. The sprung leaves crush clods as they pass under the levelling board and align clods with the press rings. The use of the in tandem with a disc cultivator for straw incorporation, is to consolidate the straw soil mix through the soil profile ensuring maximum straw soil contact to increase the breakdown process, minimise slug problems and to leave a firm weatherproof finish. 24

25 4. Adjustment / Operation 4.2 Pro-Active (Sprung) Tines The Pro-Active tines are designed to move soil and shatter clods to a greater degree than traditional rigid leading tines. The ability to move in all directions (upwards and sideways) allows them to clear stones and other obstructions. They feature simple, pinned tine depth adjustment for easy depth variation. 4.3 Levelling Boards The action of the sprung leaf type levelling boards is to carry and drop soil to level in front of the press rings, to rub clod against clod for additional soil breakdown, to force clods down into the soil profile and to present remaining clods passing between the leaves into the row of press rings. Fig. 4.03: Levelling Boards Fig. 4.02: Pro-Active (Sprung) Tines 25

26 4. Adjustment / Operation 4.4 Double Disc Roller The standard DD700 roller is made up of individual Double Disc (patented) Ring segments. The DD rings are designed to consolidate the soil whilst cutting and crushing any clods. Even in heavy, wet soils it can easily be operated with minimal blockages occurring. The DD roller carries a proportion of the machine s weight to ensure consolidation. The corrugated surface left by the roller is weatherproof both for wet or dry situations. 4.5 Work Settings In work the wing cylinders should be fully extended. The gangs are able to float over any undulations on the ground due to their floating frames. Optimum performance has been found to be achieved when the press roll rings have worn away the painted finish leaving a smooth shiny surface. When the press roll rings are new or rusty, soil may tend to pick up on the surface and blockage may occur, this will reduce when the rings are shiny again. The should be run with the chassis level front to rear by extending the drawbar cylinders to the necessary position. The cylinders should not be over extended as this will remove the load on the rings which could lead to reduced drive and hence blockage of the axles. It is not necessary to tilt the onto the transport wheels during headland turns whether the machine is used independently or in tandem with a disc cultivator. Normally, the should be tilted sufficiently onto the roll for the tines and levelling boards to clear the ground (at which point the rear axle wheels will still be clear of ground contact). Fig. 4.04: Double Disc Roller Levelling Boards The levelling boards are set using shims in the levelling board cylinders. During work, these cylinders should be retracted onto the shims but can be extended to release any soil / trash build up. With the chassis set level add shims until the levelling boards are carrying soil. The levelling boards will need to be set higher during 1st pass operations especially on ploughed land where large clods may not be able to pass under or between the sprung leaves. 26

27 4. Adjustment / Operation The boards need to carry a certain amount of soil to effect a levelling operation and also to give a clod to clod crushing action. When reversing the into corners when working headlands ensure that the levelling boards are fully raised and the machine tilted onto the roll rings far enough to allow the lower ends of the sprung leaves to clear the ground. General Rules when Setting the Run slightly tail low to give increased clod cutting and consolidation in harder conditions. In trashy conditions the use of the levelling board may be limited due to raking trash. Increase the rake angle of the levelling board in spring time operation to carry more soil for levelling. Reduce rake angle on levelling board to hold soil and rub clod against clod in harder conditions. This will also align clods with the DD rings facilitating better cutting. 4.6 Pitch Control Pitch control on the is governed by the quantity of shims fitted to the depth stops attached to the drawbar cylinders. Increasing the number of shims will lift the front of the chassis when lowered into the work position. Running the level allows the press rings to give an even consolidation and clod crushing action, with the sprung leaves of the levelling board aiding the clod crushing action, aligning the clods for the roll rings. Running the machine significantly nose down or raised will reduce the load on the rear axle leading to loss of drive of the axle and then blockage, together with a reduced consolidation effect. If any roll axle starts to block regularly, this is generally an indication that the roll axle is not tight. Failure to keep the axles tight results in loss of drive between each pair of rings allowing rings to turn individually on the axle. Should this occur the axle must be tightened immediately to prevent any damage occurring to the axle shaft. If the roll axles start to block regularly this may also be an indication that the ground conditions are too wet for the to be effective. In practice it is possible to use the on ground conditions that are unsuitable to achieve the desired effect, and it is usually possible to operate the machine without regular blockage under such unsuitable conditions, assuming that the axles are tight and rings smooth. As such, especially under wet conditions, it is advisable to check on the cultivation effect of the. Often the use of the press hours after the disc or longer following the plough gives a far superior surface consolidation effect. 27

28 4. Adjustment / Operation When the is used tilted onto the rings the loading on the disc cultivator or tractor drawbar is increased. This will cause the rear of the disc to dig deeper moving the rear gang to the right. Shortening the disc cultivator levelling springs should allow the disc cultivator to pull straight again. Equally, increased tractor drawbar loadings will deepen wheelings requiring more effort to eradicate these. It is not necessary to tilt the onto the transport wheels during headland turns whether the machine is used independently or in tandem with a disc cultivator. Fully extending the drawbar cylinder and then reversing into the headland furrow could lead to damage of the cylinder. 4.7 Using Shims Before using shims to alter machine settings ensure the machine is stationary and the tractor is turned off with the keys out. Ensure that all operators are clear of the machine and that no load is being held on any existing shims in the cylinder. To fit the shims hold them by the handle and, using a firm action, clip them onto the rod as shown in Fig They are removed by using a finger to pull firmly on the handle. Check the cylinders for damage and debris before fitting shims. Only attempt to add or remove shims using the handle. Trying to manipulate shims using the jaws could result in injury. When changing machine settings ensure both sides of the machine mirror each other. The left hand cylinder should contain the same amount of shims as the right, for example. Failure to do this could result in damage to the machine. Fig. 4.05: Shims 28

29 4. Adjustment / Operation 4.8 Work Instructions Driving speed The can be driven at speeds of up to 12 km/h. This depends on the field conditions (type of soil, surface trash, etc.). Drive more slowly if the conditions are difficult or a firmer finish is required. Beware of stones being thrown by the spring action of tines returning from their stressed state in work. Parking the Machine In order to avoid damage as a result of moisture, the machine should be parked, if possible, indoors or under cover. When manoeuvring the machine, pay attention to your surroundings. Ensure that nobody (children!) is in the manoeuvring area. Park the machine on level and solid ground. Fit wheel chocks. With the machine raised move the parking stands into position. Lower the machine onto the parking stands ensuring that it is stable. Remove the drawbar pin and drive forward slowly until hitch is clear of tractor drawbar. Lower the drawbar to the ground. Switch off the tractor. Disconnect hydraulic lines from the tractor. 4.9 Checks The working quality depends on the adjustments and checks made prior to and during work, as well as on regular servicing and maintenance of the machine. Before beginning work it is therefore important to carry out any necessary servicing and to lubricate the machine as required. Checks prior to, and during work: Is the machine correctly hitched up and the coupling device locked? Have the hydraulic and electric lines been connected according to the colour coding? Is the machine in a level operating position and the working depth set correctly? Regularly inspect the machine for damage and signs of overloading (stress cracks on welded joints, frame distortion) Working Elements Are the double disc rings and other cultivation tools in a serviceable condition? Are the scrapers still operable, so that the rolls do not jam? If parking on uneven or sloping ground chock the machine and unfold / lower first to avoid instability. 29

30 5. Servicing and Maintenance 5. Servicing and Maintenance Follow the safety instructions for servicing and maintenance. Maintenance work should only be undertaken with the machine unfolded and lowered or on stands with the hydraulic taps shut. When working under the machine ensure that the tractor handbrake is on. 5.1 Servicing Your machine has been designed and constructed for maximum performance, operational efficiency and operator friendliness under a wide variety of operating conditions. Prior to delivery, your machine has been checked at the factory and by your authorised dealer to ensure that you receive a machine in optimum condition. To ensure trouble-free operation, it is important that servicing and maintenance work is performed at the recommended intervals. 5.2 Cleaning In order to ensure that the machine is always in operating condition and to achieve optimum performance, perform the cleaning and servicing work at regular intervals. Avoid cleaning the roll bearings with a high-pressure hose or a direct water jet. The housing, screwed connections and ball bearings are not watertight. 5.3 Double Disc Axles The axles on this roller are tensioned by the main axle through the centre of the rings and bearings. Specialist equipment is required for the disassembly of Double Disc axles. Please consult your dealer under any circumstances that require disassembly of these axles. Maintenance of these rollers is limited to daily greasing of the bearings to flush out dirt, and regular inspection to ensure the assemblies are tight, and scrapers are correctly set. The axles can be tightened provided the bearing pillar U bolts are loosened to avoid preloading the bearings as they move sideways to each other. Ensure the bearing pillars are re-tightened to the mainframe after this. 5.4 Hydraulics A low oil flow should be used, i.e., tractor tickover or low flow selected. The wing circuit is controlled by an overcentre valve contained within the manifold block which positively locks oil flow until pressurised by the tractor. System pressure can be retained in the circuit even after depressurisation of the tractor quick release couplings. Exercise extreme care when checking the valve or circuits, and under no circumstances attempt to adjust or loosen fittings without prior reference to your authorised Simba Great Plains dealer, and detailed maintenance instructions. 30

31 5. Servicing and Maintenance 5.5 Tines When performing maintenance work on tines extreme care should be taken. Wear goggles and gloves at at all times when maintaining tines. Safely support unfolded machine in raised position using taps and stands before attempting maintenance work on tines. Do not attempt to assist fitting tine points with a steel headed hammer, this can lead to splintering of the metal due to its hardness, which can cause injury. If tine fitting requires assistance, a copper/ hide or plastic mallet should be used. ENGAGE POINT REMOVAL TOOL STRIKE WITH MALLET 5.6 Levelling Boards Safely support the unfolded machine in a raised position using taps and stands before attempting maintenance work on the levelling boards. 5.7 Preparation for Storage If you need to store the machine for a longer period, observe the following points: Park the machine undercover if possible. Protect the roll against rust. If you need to spray the implements with oil, use light biologically degradable oils, e.g. rape oil. Cover any rubber sections before using oil sprays. These sections must not be oiled. Remove any traces of oil with a suitable cleaning agent. 5.8 Operator Support If you have a problem, please contact your dealer. They will endeavour to solve any problems which may occur and provide you with support at all times. In order to enable your dealer to deal with problems as quickly as possible, it helps if you can provide them with the following data. Always state the: Customer Number Name and Address Machine Model Serial Number of Machine Date of Purchase and Operating Hours Type of Problem Fig. 5.01: Knock-on Tine Point Removal Tool 31

32 5. Servicing and Maintenance 5.9 Brakes & Wheel Hubs The brakes should be tested before using for the first time and after the first laden journey. Check that the road and parking brakes operate and release correctly before using the machine. Check for hydraulic fluid and air leaks. Brake and hub maintenance and servicing should be carried out by an authorised dealer Maintenance Intervals Apart from daily maintenance, the maintenance intervals are based on the number of operating hours and time data. Keep a record of your operating hours to ensure that the specified maintenance intervals are adhered to as closely as possible. Never use a machine that is due for maintenance. Ensure that all deficiencies found during regular checks are remedied immediately. Avoid sharp-edged and pointed parts (disc blades, etc.) when working on the machine. Place the machine on suitable s u p p o r t s w h e n w o r k i n g underneath! Do not work under a machine which is not supported! On a new machine tighten all nuts and bolts after 5 hours work and again after 15 hours. This also applies to parts that have been moved or replaced. After the initial 15 hours of work a once a week check should be sufficient depending on daily work rates To Adjust the System Pressure A low oil flow should be used, i.e., tractor tickover or low flow selected. The wing circuit is controlled by an overcentre valve contained within the manifold block which positively locks oil flow until pressurised by the tractor. System pressure can be retained in the circuit even after depressurisation of the tractor quick release couplings. Exercise extreme care when checking the valve or circuits, and under no circumstances attempt to adjust or loosen fittings without prior reference to your authorised dealer, and detailed maintenance instructions. It is normal to operate at bar. This can be increased to bar max, or reduced to 5 bar as conditions determine. Higher pressure will cause the wing tips to dig in causing the centre of the machine to lift it out. Too little pressure will cause the wing tips to lift out & the centre of the machine to dig in. When towing another implement behind the, the pressure may need increasing to compensate. In all cases the normal adjustment method is to minimise system pressure and then increase by adjusting the pressure valve until the desired pressure is achieved. In all cases, regardless of tractor make, adjustment should start from zero (minimum pressure) and gradually increase up to desired pressure value. 32

33 5. Servicing and Maintenance With the machine off the ground, 1. Pressurise the wings to unfold. As the unfolding begins the pressure reading on the gauge will drop. When the wings have fully unfolded the pressure reading will start to climb. Keep pressurising the wings until the gauge has stabilised at the pre-set pressure. The standard factory setting is 15 bar. 2. If the system needs adjusting:- Partially fold the wings & hold them in this position. To adjust the pressure utilise valve 3 (shown in Fig. 5.03). Unscrew the adjusting screw until no resistance can be felt (almost fully unscrewed position). Unfold the wings fully as before, checking the gauge reading. Maintain hydraulic pressure unfolding wings & adjust the screw whilst pressurising. Turning adjuster clockwise increases pressure. Turning adjuster anti-clockwise decreases pressure. Once the desired pressure is achieved lock the valve. As a check, partially fold the wings, stop, and then unfold again maintaining pressure until the gauge stabilises at your desired setting. Fig. 5.03: Manifold Block 33

34 5. Servicing and Maintenance 5.12 Maintenance Overview Key Inspect Grease Lights Before Each Use L L Wheel Nut Torque: 270Nm Tyres: 400/ Ply 500/ Ply Max Tyre Pressure: 50psi / 3.5bar Before Each Use Transport Strap Before Each Use L Tines DD Roll Lev. Board 10 Hours L All Hydraulics Wing Pivots 50 Hours Parking Stands L Before Each Use Drawbar Pivots 50 Hours Before Each Use L DD Axles Scrapers Hubs Hubs / Brakes 10 Hours 10 Hours L 600 Hours Before Each Use L 34

35 5. Servicing and Maintenance 5.13 Lubricating the Machine Please read the section below carefully before lubricating the machine. The machine must be lubricated regularly in order for it to remain serviceable. Regular lubrication also contributes towards extending the service life of your machine. The recommended lubricating intervals are specified in Maintenance Overview. After it has been washed using a highpressure hose or steam cleaned, the machine should always be lubricated using a grease gun Handling of Lubricants Please ensure that you read the following instructions as well as the relevant information. This also applies to any of your employees who handle lubricants. Hygiene Lubricants do not present a health hazard provided they are used for their specified purpose. In the case of prolonged skin contact, lubricants, especially low-viscosity oils, may remove the natural layer of fat contained in the skin, resulting in dryness and possible irritation. It is important to take extreme care when handling waste oil as it may contain other irritants. Vapours given off by cleaning agents and oils are also a potential health hazard. You should therefore not carry any oily cloths around. Change soiled work clothing as soon as possible. Always exercise extreme care and observe the recommended hygiene rules when handling mineral oil products. Details of these handling regulations can be found in information provided by the health authorities. Storage and Handling Always store lubricants where they cannot be accessed by children. Never store lubricants in open or unlabelled containers. Fresh Oil Apart from taking the usual care and observing hygiene rules, there is no need to take any special precautions when handling fresh oil. Waste Oil Waste oil can contain harmful contaminants which may cause skin cancer, allergies and other illnesses. Attention! Oil is a toxic substance. Should you swallow any oil, do not try to vomit. Contact a doctor immediately. Protect your hands with barrier cream or wear gloves to avoid contact with the skin. Wash off any traces of oil thoroughly with soap and hot water. Wash your skin thoroughly with soap and water. Use special cleaning agents to clean any dirt off your hands. Never wash oil residue from your skin with petrol, diesel fuel or paraffin. Avoid skin contact with any oily clothing. Do not keep any oily rags in your pockets. Wash soiled clothing before wearing it again. Ensure that any oily footwear is disposed of in the proper manner. 35

36 5. Servicing and Maintenance Measures in case of injury through oil Eyes: Should any oil be splashed into your eyes, rinse with water for 15 minutes. If the eye is still irritated, contact a doctor immediately If oil is swallowed If oil is swallowed, it is important not to induce vomiting. Contact a doctor immediately. Skin irritation caused by oil In case of prolonged skin contact, wash off the oil with soap and water Lubricants & Hydraulic Oil Hydraulic System The hydraulic fluid from the tractor is mixed with the hydraulic fluid from the machine. The supplied machine hydraulic system contains Total AZOLLA ZS 32 oil. Lubricants All lubricating points on the machine can be lubricated with multigrade lubricating grease as specified in DIN KP/2K Oil Spills Use either sand or a suitable granular absorbent to soak up any spilt oil. Dispose of the oil-contaminated absorbent in the proper manner. Oil Fires Never use water to extinguish an oil fire. The oil will float on the water causing the fire to spread. Burning oil-lubricant must be extinguished using a carbon dioxide powder or foam extinguisher. Always wear respiratory equipment when dealing with fires of this type. Waste Oil Disposal Oil-contaminated waste and used oil must be disposed of in accordance with current legislation. Waste oil must be collected and disposed of in accordance with local regulations. Never pour used oil into unsealed sewage systems or drains or onto the ground. 36

37 6. Faults and Remedies 6. Faults and Remedies Troubleshooting Fault Possible Cause Remedy Roll axle starts to block regularly. Machine running too tail low. Lengthen work drawbar cylinder until chassis is horizontal or just tail low. Increase quantity of shims in depth stop unit. Roll axle is not tight. Tighten axle. Ground conditions too wet. Wait for more suitable ground conditions. Roll scrapers incorrectly adjusted. Set scrapers to run just clear of rings and centrally between each ring. 37

38 7. Parts & Assembly General Assembly m Complete m Complete m Complete m Complete m Complete m-6.6m Drawbar Assembly m-8.2m Drawbar Assembly m+8.2m Drawbar Assembly (FG Option) m Chassis Assembly m Chassis Assembly Front Light Kit Rear Light Bracket Wiring Loom Assembly Stud Hub Assembly Rear Drawbar Assembly Wings m Wing Assembly RH m Wing Assembly LH m Wing Assembly RH m Wing Assembly LH m Wing Assembly RH m Wing Assembly LH m Wing Assembly RH m Wing Assembly LH m Wing Assembly RH m Wing Assembly LH Tines & Tine Frames m Pro-Active Tine Frame RH m Pro-Active Tine Frame LH m Pro-Active Tine Frame RH m Pro-Active Tine Frame LH m Pro-Active Tine Frame RH m Pro-Active Tine Frame LH m Pro-Active Tine Frame RH m Pro-Active Tine Frame LH m Pro-Active Tine Frame RH m Pro-Active Tine Frame LH Pro-Active Tine Assembly Tine Assembly - Straight Tine Tine Assembly - Cranked Tine, 220mm Sweep Tine Assembly - Cranked Tine, 320mm Sweep Levelling Boards m Levelling Board Assembly RH m Levelling Board Assembly LH m Levelling Board Assembly RH m Levelling Board Assembly LH

39 6.6m Levelling Board Assembly RH m Levelling Board Assembly LH m Levelling Board Assembly RH (Inner) m Levelling Board Assembly LH (Inner) m Levelling Board Assembly RH (Outer) m Levelling Board Assembly LH (Outer) m Levelling Board Assembly RH (Inner) m Levelling Board Assembly LH (Inner) m Levelling Board Assembly RH (Outer) m Levelling Board Assembly LH (Outer) DD700 Roll Assembly m DD700 Roll Assembly RH m DD700 Roll Assembly LH m DD700 Roll Assembly RH m DD700 Roll Assembly LH m DD700 Roll Assembly RH m DD700 Roll Assembly LH m DD700 Roll Assembly RH m DD700 Roll Assembly LH m DD700 Roll Assembly RH m DD700 Roll Assembly LH DD Axle Assembly - 5 Ring DD Axle Assembly - 7 Ring DD Axle Assembly - 8 Ring DD Axle Assembly - 9 Ring DD Axle Assembly - 10 Ring Double Disc Pillar Assembly Brakes Air Brake Circuit Layout Hydraulic Brake Circuit Layout Hydraulics m-8.2m Lift Circuit m-5.5m Wing Circuit m-8.2m Wing Circuit m-5.5m Levelling Board Circuit m Levelling Board Circuit m-8.2m Levelling Board Circuit Rear Drawbar Circuit (Lift) Rear Drawbar Circuit (Wings) Stickers m Stickers m Stickers m Stickers m Stickers m Stickers

40 40

41 AS3732 GENERAL ASSEMBLY - 4.6m ITEM PART NO DESCRIPTION QTY COMMENTS 1 AS3008 WING ASSEMBLY RH - 4.6m 1 2 AS3009 WING ASSEMBLY LH - 4.6m 1 3 AS3308 LEVELLING BOARD ASSEMBLY 4.6m LH 1 4 AS3309 LEVELLING BOARD ASSEMBLY 4.6m RH 1 5 AS3707 REAR DRAWBAR ASSEMBLY 1 6 AS3709 DRAWBAR ASSEMBLY m 1 7 AS3711 LIGHT KIT FRONT 1 OPTION 8 AS3712 REAR LIGHT BRACKETS 1 9 AS3713 CHASSIS ASSEMBLY - 4.6m - 6.6m 1 10 AS3743 UNIPRESS STICKER LAYOUT 4.6M 1 11 AS4163 WING ASSEMBLY RH - 4.6m 1 12 AS4164 WING ASSEMBLY LH - 4.6m 1 13 AS4181 TINE FRAME ASSEMBLY RH - 4.6m 1 14 AS4182 TINE FRAME ASSEMBLY LH - 4.6m 1 15 P17921 MANUAL - UNIPRESS

42 42

43 AS4152 GENERAL ASSEMBLY - UNIPRESS 5.5m ITEM PART NO DESCRIPTION QTY COMMENTS 1 AS3010 WING ASSEMBLY RH - 5.5m 1 2 AS3011 WING ASSEMBLY LH AS3306 LEVELLING BOARD ASSEMBLY 5.5m LH 1 4 AS3307 LEVELLING BOARD ASSEMBLY - 5.5m RH 1 5 AS3707 REAR DRAWBAR ASSEMBLY 1 6 AS3709 DRAWBAR ASSEMBLY AS3711 LIGHT KIT FRONT 1 OPTION 8 AS3712 REAR LIGHT BRACKETS 1 9 AS3713 CHASSIS ASSEMBLY - 4.6m - 6.6m 1 10 AS4011 UNIPRESS STICKER LAYOUT 5.5m 1 11 AS4165 DD700 ROLL ASSEMBLY RH - 5.5m 1 12 AS4166 DD700 ROLL ASSEMBLY LH AS4183 TINE FRAME ASSEMBLY RH - 5.5m 1 14 AS4184 TINE FRAME ASSEMBLY LH - 5.5m 1 15 P17921 MANUAL - UNIPRESS

44 44

45 AS4154 GENERAL ASSEMBLY - UNIPRESS 6.6m ITEM PART NO DESCRIPTION QTY COMMENTS 1 AS3014 WING ASSEMBLY RH - 6.6m 1 2 AS3015 WING ASSEMBLY LH - 6.6m 1 3 AS3302 LEVELLING BOARD ASSEMBLY 6.6m LH 1 4 AS3303 LEVELLING BOARD ASSEMBLY 6.6m RH 1 5 AS3707 REAR DRAWBAR ASSEMBLY 1 6 AS3709 DRAWBAR ASSEMBLY m 1 7 AS3711 LIGHT KIT FRONT 1 OPTION 8 AS3712 REAR LIGHT BRACKETS 1 9 AS3713 CHASSIS ASSEMBLY - 4.6m AS4013 UNIPRESS STICKER LAYOUT 6.6m 1 P AS4169 DD700 ROLL ASSEMBLY RH - 6.6m 1 12 AS4170 DD700 ROLL ASSEMBLY LH - 6.6m 1 13 AS4187 TINE FRAME ASSEMBLY RH - 6.6m 1 14 AS4188 TINE FRAME ASSEMBLY LH - 6.6m 1 15 P17921 MANUAL - UNIPRESS

46 46

47 AS4155 GENERAL ASSEMBLY - UNIPRESS 7.2m ITEM PART NO DESCRIPTION QTY COMMENTS 1 AS3511 WING ASSEMBLY RH - 7.2m 1 2 AS3512 WING ASSEMBLY LH - 7.2m 1 3 AS3513 LEVELLING BOARD ASSEMBLY RH INNER 1 4 AS3514 LEVELLING BOARD ASSEMBLY LH INNER 1 5 AS3515 LEVELLING BOARD ASSEMBLY LH OUTER 1 6 AS3516 LEVELLING BOARD ASSEMBLY RH OUTER 1 7 AS3707 REAR DRAWBAR ASSEMBLY 1 8 AS3711 LIGHT KIT FRONT 1 9 AS3712 REAR LIGHT BRACKETS 1 OPTION 10 AS4014 UNIPRESS STICKER LAYOUT 7.2m 1 11 AS4158 CHASSIS ASSEMBLY HD 1 12 AS4160 DRAWBAR ASSEMBLY HD 1 13 AS4171 DD700 ROLL ASSEMBLY RH - 7.2m 1 14 AS4172 DD700 ROLL ASSEMBLY LH - 7.2m 1 15 AS4189 TINE FRAME ASSEMBLY RH - 7.6m 1 16 AS4190 TINE FRAME ASSEMBLY LH - 7.6m 1 17 P17921 MANUAL - UNIPRESS

48 48

49 AS4156 GENERAL ASSEMBLY - UNIPRESS 8.2m ITEM PART NO DESCRIPTION QTY COMMENTS 1 AS2829 LEVELLING BOARD ASSEMBLY RH INNER 1 2 AS2830 LEVELLING BOARD ASSEMBLY RH OUTER 1 3 AS2831 LEVELLING BOARD ASSEMBLY LH INNER 1 4 AS2832 LEVELLING BOARD ASSEMBLY LH OUTER 1 5 AS3018 WING ASSEMBLY RH - 8.2m 1 6 AS3019 WING ASSEMBLY LH - 8.2m 1 7 AS3707 REAR DRAWBAR ASSEMBLY 1 8 AS3711 LIGHT KIT FRONT 1 OPTION 9 AS3712 REAR LIGHT BRACKETS 1 10 AS4016 UNIPRESS STICKER LAYOUT 8.2m 1 11 AS4158 CHASSIS ASSEMBLY HD 1 12 AS4160 DRAWBAR ASSEMBLY HD 1 13 AS4173 DD700 ROLL ASSEMBLY RH - 8.2m 1 14 AS4174 DD700 ROLL ASSEMBLY LH - 8.2m 1 15 AS4191 TINE FRAME ASSEMBLY RH - 8.2m 1 16 AS4192 TINE FRAME ASSEMBLY LH - 8.2m 1 17 P17921 MANUAL - UNIPRESS

50 ITEM DESCRIPTION:- DRAWBAR ASSEMBLY m PART NO ISSUE DESCRIPTION P00045 A BOLT M36x200 GR MATERIAL Steel, High Strength MACHINE:- UNIPRESS TITLE QTY SIMBA COMMENTS B 22 DRAWN:- DATE:- KSL 20/06/2009 CATEGORY PART NO. FROM SERIAL NO. TO SERIAL NO. COST MASS Kg ASSEMBLY ISSUE AS3709 B COMPANY 50

51 AS3709 DRAWBAR ASSEMBLY m ITEM PART NO DESCRIPTION QTY COMMENTS 1 P00045 BOLT M36x200 GR P00389 PIN Ø30x P01646 BUSH SPRUNG - Ø40xØ32x P02007 NUT LOCK M P02012 NUT LOCK M P02484 LYNCH PIN CAT P02600 WASHER FLAT M P02604 WASHER FLAT M24 Ø P02609 WASHER FLAT M P03088 BOLT M12x60 GR P05492 NUT LOCK 1" UNF 2 12 P05534 NUT LOCK M P08548 BOLT 1" UNFx7" GR. V 2 14 P09092 HOSE STOWAGE PLATE 1 15 P09112 CLAMP ½" BSP PAIR 6 16 P09113 CLAMP - TOP PLATE 2 17 P09252 HOSE MAST 1 18 P09516 HITCH - FRONT 1 19 P10049 BOLT M8x25 STAUFF STACK 4 20 P10234 LOCK CLIP 4 21 P10278 BOLT M8x45 GR P11156 SHIM KIT FOR Ø60mm ROD 1 23 P12690 BOLT M10x30 GR P16360 CAT3-CAT2 BUSH INSERT 1 25 P17122 UNIPRESS F/W DRAWBAR

52 ITEM DESCRIPTION:- DRAWBAR ASSEMBLY 7.2m - 8.2m PART NO ISSUE DESCRIPTION P00045 A BOLT M36x200 GR MATERIAL Steel, High Strength MACHINE:- UNIPRESS TITLE QTY SIMBA COMMENTS 2009 B DRAWN:- DATE:- 22 KSL 07/10/2010 CATEGORY PART NO. FROM SERIAL NO. TO SERIAL NO. COST MASS Kg ASSEMBLY ISSUE AS4160 B COMPANY 52

53 AS4160 DRAWBAR ASSEMBLY m ITEM PART NO DESCRIPTION QTY COMMENTS 1 P00045 BOLT M36x200 GR P00389 PIN Ø30x P01646 BUSH SPRUNG - Ø40xØ32x P02007 NUT LOCK M P02012 NUT LOCK M P02484 LYNCH PIN CAT P02600 WASHER FLAT M P02604 WASHER FLAT M24 Ø P02609 WASHER FLAT M P03088 BOLT M12x60 GR P05492 NUT LOCK 1" UNF 2 12 P05534 NUT LOCK M P08548 BOLT 1" UNFx7" GR. V 2 14 P09092 HOSE STOWAGE PLATE 1 15 P09112 CLAMP ½" BSP PAIR 6 16 P09113 CLAMP - TOP PLATE 2 17 P09252 HOSE MAST 1 18 P09516 HITCH - FRONT 1 19 P10049 BOLT M8x25 STAUFF STACK 4 20 P10234 LOCK CLIP 4 21 P10278 BOLT M8x45 GR P11156 SHIM KIT FOR Ø60mm ROD 1 23 P12690 BOLT M10x30 GR P16360 CAT3-CAT2 BUSH INSERT 1 25 P17946 DRAWBAR HD

54 54

55 AS3061 FG DRAWBAR ASSEMBLY m ITEM PART NO DESCRIPTION QTY COMMENTS 1 P00045 BOLT M36x200 GR P00389 PIN Ø30x P01646 BUSH SPRUNG - Ø40xØ32x P02007 NUT LOCK M P02012 NUT LOCK M P02483 LYNCH PIN CAT P02484 LYNCH PIN CAT P02600 WASHER FLAT M P02605 WASHER FLAT M24 Ø P02609 WASHER FLAT M P03088 BOLT M12x60 GR P05492 NUT LOCK 1" UNF 2 13 P05534 NUT LOCK M P08548 BOLT 1" UNFx7" GR. V 2 15 P08802 SHIM KIT 7 PIECE 2 16 P09092 HOSE STOWAGE PLATE 1 17 P09112 CLAMP ½" BSP PAIR 6 18 P09113 CLAMP - TOP PLATE 2 19 P09252 HOSE MAST 1 20 P09516 HITCH - FRONT 1 21 P10049 BOLT M8x25 STAUFF STACK 4 22 P10139 DRAWBAR - TELESCOPIC BASE 1 23 P10140 DRAWBAR - TELESCOPIC 1 24 P10278 BOLT M8x45 GR P12690 BOLT M10x30 GR P14028 PIN Ø30x P16360 CAT3-CAT2 BUSH INSERT

56 56

57 AS3713 MAIN CHASSIS - 4.6m - 6.6m ITEM PART NO DESCRIPTION QTY COMMENTS 1 P00047 BOLT M36x240 GR P00071 NIPPLE - GREASE 2 3 P00389 PIN Ø30x P01054 PIN Ø25x P01055 CYLINDER - Ø5"x P01274 PIN Ø25x P01281 BOLT M12x100 GR P01645 BUSH SPRUNG - Ø32xØ26x P01646 BUSH SPRUNG - Ø40xØ32x P01647 BUSH SPRUNG - Ø45xØ36x P01709 NUT STAYTIGHT M P02007 NUT LOCK M P02012 NUT LOCK M P02484 LYNCH PIN CAT P02541 WASHER FLAT M P02602 WASHER FLAT M P02649 BOLT M16x90 GR P02789 BOLT M8x20 GR P04128 WHEEL ASSY 400/60x STUD 2 20 P04233 SPANNER - M P04754 NUT LOCK M P05122 SERIAL PLATE 1 23 P05361 RATCHET STRAP 1 24 P05400 WASHER FLAT M P05535 WASHER FLAT M P07543 PLASTIC END CAP 40x P07546 PLASTIC END CAP 80x P08918 SHIM COLLAR 2 1/2" ROD 1 29 P10293 BOLT M6x20 GR P11689 BOLT M8x110 GR P12056 DOC + PR RED. MANIFOLD 1 32 P12358 CAPSCREW M8x60 GR P14024 BACK PLATE 3 34 P15189 BRAKED AXLE 6 STUD 1 35 P17111 MAINFRAME - U/PRESS 1 36 P17369 UNIPRESS PARKING STAND P17386 CHOCK TYPE UK46St 2 38 P17387 CHOCK CARRIER UK46ST 2 39 P17815 MANUAL HOLDER - COMPLETE 1 40 P17954 WHEEL CHOCK MOUNT LH 1 41 P17955 WHEEL CHOCK MOUNT RH

58 58

59 AS4158 CHASSIS HD ASSEMBLY (7.2m-8.2m) ITEM PART NO DESCRIPTION QTY COMMENTS 1 P00047 BOLT M36x240 GR P00071 NIPPLE - GREASE 2 3 P00389 PIN Ø30x P01054 PIN Ø25x P01055 CYLINDER - Ø5"x P01274 PIN Ø25x P01281 BOLT M12x100 GR P01645 BUSH SPRUNG - Ø32xØ26x P01646 BUSH SPRUNG - Ø40xØ32x P01647 BUSH SPRUNG - Ø45xØ36x P01709 NUT STAYTIGHT M P02007 NUT LOCK M P02012 NUT LOCK M P02484 LYNCH PIN CAT P02541 WASHER FLAT M P02602 WASHER FLAT M P02649 BOLT M16x90 GR P02789 BOLT M8x20 GR P03788 WHEEL ASSEMBLY - 500/ P04233 SPANNER - M P04754 NUT LOCK M P05122 SERIAL PLATE 1 23 P05361 RATCHET STRAP 1 24 P05400 WASHER FLAT M P05535 WASHER FLAT M P07543 PLASTIC END CAP 40x P07546 PLASTIC END CAP 80x P08918 SHIM COLLAR 2 1/2" ROD 1 29 P10293 BOLT M6x20 GR P11689 BOLT M8x110 GR P12056 DOC + PR RED. MANIFOLD 1 32 P12358 CAPSCREW M8x60 GR P14024 BACK PLATE 3 34 P15189 BRAKED AXLE 6 STUD 1 35 P17369 UNIPRESS PARKING STAND P17386 CHOCK TYPE UK46St 2 37 P17387 CHOCK CARRIER UK46ST 2 38 P17815 MANUAL HOLDER - COMPLETE 1 39 P17922 CHASSIS HD 1 40 P17954 WHEEL CHOCK MOUNT LH 1 41 P17955 WHEEL CHOCK MOUNT RH

60 ITEM CULTIPRESS (2700) DESCRIPTION:- LIGHT KIT FRONT PART P15561 P15560 P07543 P05535 P14973 P04754 P02601 P09597 P02007 P00002 NO ISSUE A C LIGHT WASHER PLASTIC NUT BOLT LOCK M8x25 U BOARD BEAM M12 END DESCRIPTION FLAT M8 M12 GR8.8 GR. CAP FLH FRH M8 M x40 70x54 ABS Welded Low Steel, Alloy Plastic - High MATERIAL EN 43C Steel 8 Strength Mild 8 UNIPRESS (2700) DATE:- MACHINE:- UNI/CULTIPRESS SIMBA 2009 DRAWN:- KSL 14/05/2009 PART NO. FROM SERIAL NO. TO SERIAL NO. ASSEMBLY AS3711 ISSUE A QTY TITLE USE P05213 COMMENTS B F CATEGORY COST MASS Kg COMPANY 60

61 AS3711 FRONT LIGHT KIT ITEM PART NO DESCRIPTION QTY COMMENTS 1 P00002 BOLT U M12 GR8.8 70x P02007 NUT LOCK M P02601 WASHER FLAT M P04754 NUT LOCK M8 8 5 P05535 WASHER FLAT M P07543 PLASTIC END CAP 40x P09597 BOLT M8x25 GR P14973 LIGHT BEAM 1 9 P15560 LIGHT BOARD FRH 1 10 P15561 LIGHT BOARD FLH

62 DESCRIPTION:- REAR LIGHT BRACKETS PART P15563 P15562 P09597 P04754 P07981 P02602 P07980 P02008 P17128 P07543 P17127 P01901 P15567 P05535 P05400 NO ISSUE C A BOLT NUT CAPSCREW LIGHT PLASTIC FLASHING WASHER LOCK M8x25 M16x80 BOARD BRACKET END DESCRIPTION FLAT BEACON M8 M6 M16 M6x40 GR. CAP RLH RRH M16 M8 'TYPE 8.8 RH x40 GR10.9 T' Low Steel, ABS EN 50B Alloy Plastic - High MATERIAL EN / S355JR 8 16T Strength DATE:- MACHINE:- UNI/CULTIPRESS SIMBA 2009 DRAWN:- KSL 30/07/2009 PART NO. FROM SERIAL NO. TO SERIAL NO. ASSEMBLY AS3712 QTY TITLE COMPLETE USE UMBRACO DIN 985 P05213 COMMENTS F B CATEGORY COST MASS Kg COMPANY 10 ISSUE A 62 ITEM

63 AS3712 REAR LIGHT BRACKETS ITEM PART NO DESCRIPTION QTY COMMENTS 1 P01901 BOLT M16x80 GR P02008 NUT LOCK M16 'TYPE T' 4 3 P02602 WASHER FLAT M P04754 NUT LOCK M8 8 5 P05400 WASHER FLAT M6 3 6 P05535 WASHER FLAT M P07543 PLASTIC END CAP 40x P07980 CAPSCREW M6x40 GR P07981 NUT LOCK M P09597 BOLT M8x25 GR P15562 LIGHT BOARD RRH 1 12 P15563 LIGHT BOARD RLH 1 13 P15567 FLASHING BEACON 1 14 P17127 LIGHT BRACKET LH 1 15 P17128 LIGHT BRACKET RH

64 4 5 UNIPRESS WIRING LOOM LAYOUT 3 DATE:- MACHINE:- UNIPRESS 4 SIMBA DESCRIPTION:- DRAWN:- KSL 25/05/2009 PART NO. FROM SERIAL NO. TO SERIAL NO. 2 ASSEMBLY ISSUE AS3729 B 64

65 AS3729 UNIPRESS WIRING LOOM LAYOUT ITEM PART NO DESCRIPTION QTY COMMENTS 1 P17195 CHASSIS LOOM 1 2 P17197 FRONT DRAWBAR LOOM 1 3 P17199 REAR DRAWBAR LOOM 1 4 P18115 REAR LIGHTS LOOM 2 5 P18116 BEACON EXTENSION LEAD

66 DESCRIPTION:- HUB ASSEMBLY 6 STUD COMPLETE MACHINE:- SIMBA SL SIMBA DRAWN:- DATE:- 2 4 ARH 04/10/ PART NO. FROM SERIAL NO. TO SERIAL NO. P ASSEMBLY ISSUE AS3374 A 66

67 AS3374 BRAKED HUB ASSEMBLY 6 STUD HUB ITEM PART NO DESCRIPTION QTY COMMENTS 1 P13034 HUB 6 STUD 2 2 P13035 SHIM WASHER Ø120xØ P13037 GREASE SEAL Ø120xØ P13038 SHIM WASHER Ø80xØ P13041 NUT CASTLE M39x P16269 WHEEL STUD M18x1.5x P13044 WHEEL NUT M18x P13040 SPRING CLIP Ø4x P13042 DUST CAP 6 STUD 2 10 P13036 BEARING Ø120xØ P13039 BEARING Ø90xØ P16084 BRAKE DRUM - 6 STUD 2 13 P16073 BRAKE SHOE 60x P16075 ACTUATOR CAM 645mm 2 15 P16079 LOCATION SPIGOT 2 16 P16080 WASHER SHAKEPROOF M P16077 SHIELD 2 18 P16095 BACKPLATE 2 19 P01358 NUT PLAIN M P14007 BOTTOM AXLE 1 21 P13829 BRAKE LEVER 2 22 P16097 CIRCLIP DIN x P16096 CIRCLIP DIN471-24x P16074 TENSION SPRING YELLOW 2 25 P16076 TENSION SPRING GREY

68 68

69 AS3707 REAR DRAWBAR ASSEMBLY ITEM PART NO DESCRIPTION QTY COMMENTS 1 P00160 CYLINDER - Ø3¾"x9" P00200 BANJO BLOCK ½" BSP 2 3 P00201 BANJO BOLT ½" BSP 2 4 P00203 ADAPTOR MALE-MALE ½" BSP 5 5 P00206 ADAPTOR MALE-FEM ½" BSP 1 6 P00774 SHUT OFF TAP ½" BSP 5 7 P01274 PIN Ø25x P01645 BUSH SPRUNG - Ø32xØ26x P02007 NUT LOCK M P02011 NUT LOCK M P02263 DOWTY SEAL ½" BSP P02484 LYNCH PIN CAT P02486 R CLIP Ø7x P02601 WASHER FLAT M P02608 WASHER FLAT M P02730 QUICK RELEASE FEM. ½" BSP 4 17 P02735 BULKHEAD ½" BSP 4 18 P02793 BOLT M30x220 GR P03219 PIN Ø36x P04418 PIN Ø25x230 TYPE B 1 21 P08564 TRAILER SOCKET FEMALE 12N KIT 1 22 P10073 DRAWBAR CLEVIS 1 23 P10870 BOLT M12x30 GR P12425 SOCKET 12N - BOOT 1 25 P12426 SOCKET 12N - INSTALL KIT 1 26 P15835 BULK HEAD PLATE 1 27 P17135 REAR DRAWBAR

70 70

71 AS3008 WING ASSEMBLY RH - 4.6m ITEM PART NO DESCRIPTION QTY COMMENTS 1 P00071 NIPPLE - GREASE 2 2 P00166 CYLINDER - Ø75x P01274 PIN Ø25x P01645 BUSH SPRUNG - Ø32xØ26x P02484 LYNCH PIN CAT P06155 RATCHET STRAP MOUNT 1 7 P09112 CLAMP ½" BSP PAIR 2 8 P09113 CLAMP - TOP PLATE 2 9 P09355 WING FRAME RH - 4.6m 1 10 P10278 BOLT M8x45 GR

72 72

73 AS3009 WING ASSEMBLY LH - 4.6m ITEM PART NO DESCRIPTION QTY COMMENTS 1 P00071 NIPPLE - GREASE 2 2 P00166 CYLINDER - Ø75x P01274 PIN Ø25x P01645 BUSH SPRUNG - Ø32xØ26x P02484 LYNCH PIN CAT P06155 RATCHET STRAP MOUNT 1 7 P09112 CLAMP ½" BSP PAIR 2 8 P09113 CLAMP - TOP PLATE 2 9 P09356 WING FRAME LH - 4.6m 1 10 P10278 BOLT M8x45 GR

74 74

75 AS3010 WING ASSEMBLY RH - 5.5m ITEM PART NO DESCRIPTION QTY COMMENTS 1 P00071 NIPPLE - GREASE 2 2 P00166 CYLINDER - Ø75x P01274 PIN Ø25x P01645 BUSH SPRUNG - Ø32xØ26x P02484 LYNCH PIN CAT P06155 RATCHET STRAP MOUNT 1 7 P09112 CLAMP ½" BSP PAIR 2 8 P09113 CLAMP - TOP PLATE 2 9 P09357 WING FRAME RH - 5.5m 1 10 P10278 BOLT M8x45 GR

76 76

77 AS3011 WING ASSEMBLY LH - 5.5m ITEM PART NO DESCRIPTION QTY COMMENTS 1 P00071 NIPPLE - GREASE 2 2 P00166 CYLINDER - Ø75x P01274 PIN Ø25x P01645 BUSH SPRUNG - Ø32xØ26x P02484 LYNCH PIN CAT P06155 RATCHET STRAP MOUNT 1 7 P09112 CLAMP ½" BSP PAIR 2 8 P09113 CLAMP - TOP PLATE 2 9 P09358 WING FRAME LH - 5.5m 1 10 P10278 BOLT M8x45 GR

78 78

79 AS3014 WING ASSEMBLY RH - 6.6m ITEM PART NO DESCRIPTION QTY COMMENTS 1 P00071 NIPPLE - GREASE 2 2 P00164 CYLINDER - Ø3¾"x P01274 PIN Ø25x P01645 BUSH SPRUNG - Ø32xØ26x P02484 LYNCH PIN CAT P06155 RATCHET STRAP MOUNT 1 7 P09112 CLAMP ½" BSP PAIR 2 8 P09113 CLAMP - TOP PLATE 2 9 P09361 WING FRAME RH - 6.6m 1 10 P10278 BOLT M8x45 GR

80 80

81 AS3015 WING ASSEMBLY - UNIPRESS 6.6m ITEM PART NO DESCRIPTION QTY COMMENTS 1 P00071 NIPPLE - GREASE 2 2 P00164 CYLINDER - Ø3¾"x P01274 PIN Ø25x P01645 BUSH SPRUNG - Ø32xØ26x P02484 LYNCH PIN CAT P06155 RATCHET STRAP MOUNT 1 7 P09112 CLAMP ½" BSP PAIR 2 8 P09113 CLAMP - TOP PLATE 2 9 P09362 WING FRAME LH - 6.6m 1 10 P10278 BOLT M8x45 GR

82 82

83 AS3511 WING ASSEMBLY RH - 7.2m ITEM PART NO DESCRIPTION QTY COMMENTS 1 P00071 NIPPLE - GREASE 2 2 P00164 CYLINDER - Ø3¾"x P01274 PIN Ø25x P01645 BUSH SPRUNG - Ø32xØ26x P02484 LYNCH PIN CAT P06155 RATCHET STRAP MOUNT 1 7 P09112 CLAMP ½" BSP PAIR 3 8 P09113 CLAMP - TOP PLATE 3 9 P09363 WING FRAME RH - 7.6m 1 10 P10278 BOLT M8x45 GR

84 84

85 AS3512 WING ASSEMBLY LH - 7.2m ITEM PART NO DESCRIPTION QTY COMMENTS 1 P00071 NIPPLE - GREASE 2 2 P00164 CYLINDER - Ø3¾"x P01274 PIN Ø25x P01645 BUSH SPRUNG - Ø32xØ26x P02484 LYNCH PIN CAT P06155 RATCHET STRAP MOUNT 1 7 P09112 CLAMP ½" BSP PAIR 3 8 P09113 CLAMP - TOP PLATE 3 9 P09364 WING FRAME LH - 7.6m 1 10 P10278 BOLT M8x45 GR

86 86

87 AS3018 WING ASSEMBLY RH - 8.2m ITEM PART NO DESCRIPTION QTY COMMENTS 1 P00071 NIPPLE - GREASE 2 2 P00164 CYLINDER - Ø3¾"x P01274 PIN Ø25x P01645 BUSH SPRUNG - Ø32xØ26x P02484 LYNCH PIN CAT P06155 RATCHET STRAP MOUNT 1 7 P09112 CLAMP ½" BSP PAIR 3 8 P09113 CLAMP - TOP PLATE 3 9 P09365 WING FRAME RH - 8.2m 1 10 P10278 BOLT M8x45 GR

88 88

89 AS3019 WING ASSEMBLY LH - 8.2m ITEM PART NO DESCRIPTION QTY COMMENTS 1 P00071 NIPPLE - GREASE 2 2 P00164 CYLINDER - Ø3¾"x P01274 PIN Ø25x P01645 BUSH SPRUNG - Ø32xØ26x P02484 LYNCH PIN CAT P06155 RATCHET STRAP MOUNT 1 7 P09112 CLAMP ½" BSP PAIR 3 8 P09113 CLAMP - TOP PLATE 3 9 P09366 WING FRAME LH - 8.2m 1 10 P10278 BOLT M8x45 GR

90 90

91 AS4181 TINE FRAME ASSEMBLY RH - 4.6M ITEM PART NO DESCRIPTION QTY COMMENTS 1 AS4175 PROACTIVE TINE ASSEMBLY - SPRING ONLY 7 2 AS4176 TINE ASSEMBLY - STRAIGHT TINE 7 3 P02009 NUT LOCK M P02603 WASHER FLAT M P02655 BOLT M20x240 GR P09432 RETAINING PLATE 120x120x4 2 7 P12115 TINE FRAME RH - 4.6m

92 92

93 AS4182 TINE FRAME ASSEMBLY LH - 4.6M ITEM PART NO DESCRIPTION QTY COMMENTS 1 AS4175 PROACTIVE TINE ASSEMBLY - SPRING ONLY 8 2 AS4176 TINE ASSEMBLY - STRAIGHT TINE 8 3 P02009 NUT LOCK M P02603 WASHER FLAT M P02655 BOLT M20x240 GR P04053 CLAMP PLATE 2x122x P09432 RETAINING PLATE 120x120x4 1 8 P12114 TINE FRAME LH - 4.6m

94 94

95 AS4183 TINE FRAME ASSEMBLY RH - 5.5m ITEM PART NO DESCRIPTION QTY COMMENTS 1 AS4175 PROACTIVE TINE ASSEMBLY - SPRING ONLY 8 2 AS4176 TINE ASSEMBLY - STRAIGHT TINE 8 3 P02009 NUT LOCK M P02603 WASHER FLAT M P02655 BOLT M20x240 GR P09432 RETAINING PLATE 120x120x4 2 7 P12119 TINE FRAME RH m

96 96

97 AS4184 TINE FRAME ASSEMBLY LH - 5.5m ITEM PART NO DESCRIPTION QTY COMMENTS 1 AS4175 PROACTIVE TINE ASSEMBLY - SPRING ONLY 9 2 AS4176 TINE ASSEMBLY - STRAIGHT TINE 9 3 P02009 NUT LOCK M P02603 WASHER FLAT M P02655 BOLT M20x240 GR P04053 CLAMP PLATE 2x122x P09432 RETAINING PLATE 120x120x4 1 8 P12118 TINE FRAME LH m

98 98

99 AS4187 TINE FRAME ASSEMBLY RH - 6.6m ITEM PART NO DESCRIPTION QTY COMMENTS 1 AS4175 PROACTIVE TINE ASSEMBLY - SPRING ONLY 10 2 AS4176 TINE ASSEMBLY - STRAIGHT TINE 10 3 P02009 NUT LOCK M P02603 WASHER FLAT M P02655 BOLT M20x240 GR P09432 RETAINING PLATE 120x120x4 2 7 P12121 TINE FRAME RH - 6.6m

100 100

101 AS4188 TINE FRAME ASSEMBLY LH - 6.6m ITEM PART NO DESCRIPTION QTY COMMENTS 1 AS4175 PROACTIVE TINE ASSEMBLY - SPRING ONLY 11 2 AS4176 TINE ASSEMBLY - STRAIGHT TINE 11 3 P02009 NUT LOCK M P02603 WASHER FLAT M P02655 BOLT M20x240 GR P04053 CLAMP PLATE 2x122x P09432 RETAINING PLATE 120x120x4 1 8 P12120 TINE FRAME LH - 6.6m

102 102

103 AS4189 TINE FRAME ASSEMBLY RH - 7.2m ITEM PART NO DESCRIPTION QTY COMMENTS 1 AS4175 PROACTIVE TINE ASSEMBLY - SPRING ONLY 11 2 AS4176 TINE ASSEMBLY - STRAIGHT TINE 11 3 P02009 NUT LOCK M P02603 WASHER FLAT M P02655 BOLT M20x240 GR P09432 RETAINING PLATE 120x120x4 3 7 P12123 TINE FRAME RH - 7.6m

104 104

105 AS4190 TINE FRAME ASSEMBLY LH - 7.2m ITEM PART NO DESCRIPTION QTY COMMENTS 1 AS4175 PROACTIVE TINE ASSEMBLY - SPRING ONLY 12 2 AS4176 TINE ASSEMBLY - STRAIGHT TINE 12 3 P02009 NUT LOCK M P02603 WASHER FLAT M P02655 BOLT M20x240 GR P04053 CLAMP PLATE 2x122x P09432 RETAINING PLATE 120x120x4 2 8 P12122 TINE FRAME LH -7.6m

106 106

107 AS4191 TINE FRAME ASSEMBLY RH - 8.2m ITEM PART NO DESCRIPTION QTY COMMENTS 1 AS4175 PROACTIVE TINE ASSEMBLY - SPRING ONLY 13 2 AS4176 TINE ASSEMBLY - STRAIGHT TINE 13 3 P02009 NUT LOCK M P02603 WASHER FLAT M P02655 BOLT M20x240 GR P09432 RETAINING PLATE 120x120x4 3 7 P12125 TINE FRAME RH - 8.2m

108 108

109 AS4192 TINE FRAME ASSEMBLY LH - 8.2m ITEM PART NO DESCRIPTION QTY COMMENTS 1 AS4175 PROACTIVE TINE ASSEMBLY - SPRING ONLY 14 2 AS4176 TINE ASSEMBLY - STRAIGHT TINE 14 3 P02009 NUT LOCK M P02603 WASHER FLAT M P02655 BOLT M20x240 GR P04053 CLAMP PLATE 2x122x P09432 RETAINING PLATE 120x120x4 2 8 P12124 TINE FRAME LH - 8.2m

110 14 3 DESCRIPTION:- PROACTIVE TINE ASSEMBLY - SPRING ONLY MACHINE:- 1 SIMBA DRAWN:- DATE: EH 13/10/2010 PART NO. FROM SERIAL NO. TO SERIAL NO. ASSEMBLY ISSUE AS4175 B 110

111 AS4175 PRO-ACTIVE TINE ASSEMBLY - SPRING ONLY ITEM PART NO DESCRIPTION QTY COMMENTS 1 P01102 BOLT M16x70 GR P01704 BOLT M16x50 GR P02008 NUT LOCK M16 'TYPE T' 6 DIN P02602 WASHER FLAT M P05207 PIN Ø16x P09280 BOLT M16x45 GR P12524 TINE CLAMP UNIT 1 8 P12525 BUSH Ø25xØ16.5x P12574 BOLT U M16 130/ GR P12575 RETAINING PLATE 1 11 P16788 CIRCLE COTTER 52X P17425 PROACTIVE TINE 150X P17431 NUT LOCK M16 PHILIDAS 3 14 P17927 SPRING HELPER

112 112

113 AS4176 TINE ASSEMBLY - STRAIGHT TINE ITEM PART NO DESCRIPTION QTY COMMENTS 1 P03017 POINT 1½" REVERSIBLE 1 2 P07131 NUT LOCK 7/16"UNF 2 3 P12628 TINE 2x1 SHORT 1 4 P17855 BOLT 7/16" UNFx

114 114

115 AS4177 CRANKED TINE 220mm SWEEP ITEM PART NO DESCRIPTION QTY COMMENTS 1 P12588 TINE - SWEEP TYPE 1 2 P12711 WEDGE COMPLETE 1 3 P12713 POINT KNOCK ON 220mm 1 4 P14913 BOLT 1/2" UNCx3" CSK SQ. 2 5 P14914 NUT LOCK 1/2" UNC

116 116

117 AS4178 CRANKED TINE 320mm SWEEP ITEM PART NO DESCRIPTION QTY COMMENTS 1 P12588 TINE - SWEEP TYPE 1 2 P12711 WEDGE COMPLETE 1 3 P12712 POINT KNOCK ON 320mm 1 4 P14913 BOLT 1/2" UNCx3" CSK SQ. 2 5 P14914 NUT LOCK 1/2" UNC

118 118

119 AS3309 LEVELLING BOARD ASSEMBLY - 4.6m RH ITEM PART NO DESCRIPTION QTY COMMENTS 1 P01224 BOLT M20x180 GR P01281 BOLT M12x100 GR P01619 BOLT U M20 GR x P02007 NUT LOCK M P02009 NUT LOCK M P02483 LYNCH PIN CAT P02601 WASHER FLAT M P02603 WASHER FLAT M P03088 BOLT M12x60 GR P04126 BUSH SPRUNG - Ø32xØ26x P07545 PLASTIC END CAP 60x P07724 PIN Ø25x P08013 CYLINDER - Ø63x P08802 SHIM KIT 7 PIECE 1 15 P09400 SHIM KIT PLATE Ø1¼" ROD 1 16 P12675 UPPER RAM POINT 1 17 P12677 LEVELLING BOARD PILLAR 2 18 P13402 LEAF CLAMP 60x60 RHS 9 19 P13406 BOLT M10x35 DOME SQ P13407 NUT TOOTHED M P13416 SPRUNG LEAF 80x P13417 WEAR PLATE 80mm 9 23 P15230 PILLAR DISC - SQUARE 1 24 P15231 LOCKING COLLAR 2 25 P15232 CYLINDER PLATE SQUARE 2 26 P16050 LEVELLING BEAM 2010mm

120 120

121 AS3308 LEVELLING BOARD ASSEMBLY - 4.6m LH ITEM PART NO DESCRIPTION QTY COMMENTS 1 P01224 BOLT M20x180 GR P01281 BOLT M12x100 GR P01619 BOLT U M20 GR x P02007 NUT LOCK M P02009 NUT LOCK M P02483 LYNCH PIN CAT P02601 WASHER FLAT M P02603 WASHER FLAT M P03088 BOLT M12x60 GR P04126 BUSH SPRUNG - Ø32xØ26x P07545 PLASTIC END CAP 60x P07724 PIN Ø25x P08013 CYLINDER - Ø63x P08802 SHIM KIT 7 PIECE 1 15 P09400 SHIM KIT PLATE Ø1¼" ROD 1 16 P12675 UPPER RAM POINT 1 17 P12677 LEVELLING BOARD PILLAR 2 18 P13402 LEAF CLAMP 60x60 RHS P13406 BOLT M10x35 DOME SQ P13407 NUT TOOTHED M P13416 SPRUNG LEAF 80x P13417 WEAR PLATE 80mm P15230 PILLAR DISC - SQUARE 1 24 P15231 LOCKING COLLAR 2 25 P15232 CYLINDER PLATE SQUARE 2 26 P16049 LEVELLING BEAM 2250mm

122 122

123 AS3307 LEVELLING BOARD ASSEMBLY - 5.5m RH ITEM PART NO DESCRIPTION QTY COMMENTS 1 P01224 BOLT M20x180 GR P01281 BOLT M12x100 GR P01619 BOLT U M20 GR x P02007 NUT LOCK M P02009 NUT LOCK M P02483 LYNCH PIN CAT P02601 WASHER FLAT M P02603 WASHER FLAT M P03088 BOLT M12x60 GR P04126 BUSH SPRUNG - Ø32xØ26x P07545 PLASTIC END CAP 60x P07724 PIN Ø25x P08013 CYLINDER - Ø63x P08802 SHIM KIT 7 PIECE 1 15 P09400 SHIM KIT PLATE Ø1¼" ROD 1 16 P12675 UPPER RAM POINT 1 17 P12677 LEVELLING BOARD PILLAR 3 18 P13402 LEAF CLAMP 60x60 RHS P13406 BOLT M10x35 DOME SQ P13407 NUT TOOTHED M P13416 SPRUNG LEAF 80x P13417 WEAR PLATE 80mm P15230 PILLAR DISC - SQUARE 2 24 P15231 LOCKING COLLAR 4 25 P15232 CYLINDER PLATE SQUARE 2 26 P16048 LEVELLING BEAM 2700mm

124 124

125 AS3306 LEVELLING BOARD ASSEMBLY 5.5m LH ITEM PART NO DESCRIPTION QTY COMMENTS 1 P01224 BOLT M20x180 GR P01281 BOLT M12x100 GR P01619 BOLT U M20 GR x P02007 NUT LOCK M P02009 NUT LOCK M P02483 LYNCH PIN CAT P02601 WASHER FLAT M P02603 WASHER FLAT M P03088 BOLT M12x60 GR P04126 BUSH SPRUNG - Ø32xØ26x P07545 PLASTIC END CAP 60x P07724 PIN Ø25x P08013 CYLINDER - Ø63x P08802 SHIM KIT 7 PIECE 1 15 P09400 SHIM KIT PLATE Ø1¼" ROD 1 16 P12675 UPPER RAM POINT 1 17 P12677 LEVELLING BOARD PILLAR 3 18 P13402 LEAF CLAMP 60x60 RHS P13406 BOLT M10x35 DOME SQ P13407 NUT TOOTHED M P13416 SPRUNG LEAF 80x P13417 WEAR PLATE 80mm P15230 PILLAR DISC - SQUARE 2 24 P15231 LOCKING COLLAR 4 25 P15232 CYLINDER PLATE SQUARE 2 26 P16046 LEVELLING BEAM 2720mm

126 126

127 AS3303 LEVELLING BOARD ASSEMBLY - 6.6m RH ITEM PART NO DESCRIPTION QTY COMMENTS 1 P01224 BOLT M20x180 GR P01281 BOLT M12x100 GR P01619 BOLT U M20 GR x P02007 NUT LOCK M P02009 NUT LOCK M P02483 LYNCH PIN CAT P02601 WASHER FLAT M P02603 WASHER FLAT M P03088 BOLT M12x60 GR P04126 BUSH SPRUNG - Ø32xØ26x P07545 PLASTIC END CAP 60x P07724 PIN Ø25x P08013 CYLINDER - Ø63x P08802 SHIM KIT 7 PIECE 1 15 P09400 SHIM KIT PLATE Ø1¼" ROD 1 16 P12675 UPPER RAM POINT 1 17 P12677 LEVELLING BOARD PILLAR 3 18 P13402 LEAF CLAMP 60x60 RHS P13406 BOLT M10x35 DOME SQ P13407 NUT TOOTHED M P13416 SPRUNG LEAF 80x P13417 WEAR PLATE 80mm P15230 PILLAR DISC - SQUARE 2 24 P15231 LOCKING COLLAR 4 25 P15232 CYLINDER PLATE SQUARE 2 26 P16038 LEVELLING BEAM 2930mm

128 ITEM DESCRIPTION:- LEVELLING BOARD ASSEMBLY 6.6m LH PART NO ISSUE DESCRIPTION P01224 A BOLT M20x180 GR MATERIAL Steel, High Strength Low Alloy MACHINE:- UNIPRESS QTY TITLE SIMBA COMMENTS B DRAWN:- DATE:- PJG 26/11/2007 CATEGORY VIEW FROM REAR OF MACHINE (410) PART NO. FROM SERIAL NO. TO SERIAL NO. ASSEMBLY ISSUE AS3302 A COST MASS Kg COMPANY

129 AS3302 LEVELLING BOARD ASSEMBLY 6.6m LH ITEM PART NO DESCRIPTION QTY COMMENTS 1 P01224 BOLT M20x180 GR P01281 BOLT M12x100 GR P01619 BOLT U M20 GR x P02007 NUT LOCK M P02009 NUT LOCK M P02483 LYNCH PIN CAT P02601 WASHER FLAT M P02603 WASHER FLAT M P03088 BOLT M12x60 GR P04126 BUSH SPRUNG - Ø32xØ26x P07545 PLASTIC END CAP 60x P07724 PIN Ø25x P08013 CYLINDER - Ø63x P08802 SHIM KIT 7 PIECE 1 15 P09400 SHIM KIT PLATE Ø1¼" ROD 1 16 P12675 UPPER RAM POINT 1 17 P12677 LEVELLING BOARD PILLAR 3 18 P13402 LEAF CLAMP 60x60 RHS P13406 BOLT M10x35 DOME SQ P13407 NUT TOOTHED M P13416 SPRUNG LEAF 80x P13417 WEAR PLATE 80mm P15230 PILLAR DISC - SQUARE 2 24 P15231 LOCKING COLLAR 4 25 P15232 CYLINDER PLATE SQUARE 2 26 P16037 LEVELLING BEAM 3180mm

130 130

131 AS3513 LEVELLING BOARD - 7.2m RH INNER ITEM PART NO DESCRIPTION QTY COMMENTS 1 P00006 BOLT M12x80 GR P01281 BOLT M12x100 GR P01619 BOLT U M20 GR x P02007 NUT LOCK M P02008 NUT LOCK M16 'TYPE T' 4 6 P02009 NUT LOCK M P02483 LYNCH PIN CAT P02601 WASHER FLAT M P02602 WASHER FLAT M P02603 WASHER FLAT M P03088 BOLT M12x60 GR P04126 BUSH SPRUNG - Ø32xØ26x P06802 BOLT U M16 GR x P07545 PLASTIC END CAP 60x P07724 PIN Ø25x P08013 CYLINDER - Ø63x P08802 SHIM KIT 7 PIECE 1 18 P09400 SHIM KIT PLATE Ø1¼" ROD 1 19 P12677 LEVELLING BOARD PILLAR 2 20 P13402 LEAF CLAMP 60x60 RHS 9 21 P13406 BOLT M10x35 DOME SQ P13407 NUT TOOTHED M P13416 SPRUNG LEAF 80x P13417 WEAR PLATE 80mm 9 25 P15230 PILLAR DISC - SQUARE 1 26 P15231 LOCKING COLLAR 2 27 P15232 CYLINDER PLATE SQUARE 2 28 P15233 RAM POINT - UPPER 1 29 P16053 LEVELLING BEAM 2070mm 1 30 P16348 LEVELLING BOARD TIE

132 2310 (1690) LEVELLING BOARD ASSEMBLY LH INNER DATE:- MACHINE:- UNIPRESS 7.6m SIMBA 2008 DESCRIPTION:- DRAWN:- PJG 26/11/2007 PART NO. FROM SERIAL NO. TO SERIAL NO. ASSEMBLY ISSUE AS3514 A ITEM PART P12677 P15233 P15232 P09400 P15231 P03088 P15230 P08802 P13417 P02007 P02603 P08013 P13416 P02602 P13407 P01619 P07724 P02601 P07545 P13406 P02483 P02009 P06802 P13402 P01281 P16348 P16052 P04126 P00006 P02008 NO ISSUE C A B RAM CYLINDER SHIM LOCKING PILLAR WASHER WEAR SPRUNG NUT PIN LYNCH PLASTIC BOLT LEVELLING LEAF BUSH Ø25x100 TOOTHED POINT KIT CLAMP M12x60 M10x35 M12x100 U M12x80 SPRUNG PLATE PIN DISC M20 M16 END DESCRIPTION LEAF 7 FLAT COLLAR PLATE M16 - M20 PIECE CAT BOARD BEAM - Ø63x130 GR8.8 - UPPER 60x60 GR. 80mm DOME CAP SQUARE 80x10 M20 M16 M12 M10 'TYPE - 1 Ø1¼" Ø32xØ26x20 SQUARE mm 60x60 145x x RHS PILLAR TIE SQ. - T' ROD Low Steel, Abro EN ABS 45 50B Alloy Plastic High MATERIAL / 43C EN CrBo 251A58 / S355JR 8 Strength QTY TITLE C/W DIN J M8x60 COMMENTS + LOCK NUT P B H F CATEGORY COST MASS Kg KN HENDRY FARM PRODUCTS POWER COMPANY 132

133 AS3514 LEVELLING BOARD - 7.2m LH INNER ITEM PART NO DESCRIPTION QTY COMMENTS 1 P00006 BOLT M12x80 GR P01281 BOLT M12x100 GR P01619 BOLT U M20 GR x P02007 NUT LOCK M P02008 NUT LOCK M16 'TYPE T' 4 6 P02009 NUT LOCK M P02483 LYNCH PIN CAT P02601 WASHER FLAT M P02602 WASHER FLAT M P02603 WASHER FLAT M P03088 BOLT M12x60 GR P04126 BUSH SPRUNG - Ø32xØ26x P06802 BOLT U M16 GR x P07545 PLASTIC END CAP 60x P07724 PIN Ø25x P08013 CYLINDER - Ø63x P08802 SHIM KIT 7 PIECE 1 18 P09400 SHIM KIT PLATE Ø1¼" ROD 1 19 P12677 LEVELLING BOARD PILLAR 2 20 P13402 LEAF CLAMP 60x60 RHS P13406 BOLT M10x35 DOME SQ P13407 NUT TOOTHED M P13416 SPRUNG LEAF 80x P13417 WEAR PLATE 80mm P15230 PILLAR DISC - SQUARE 1 26 P15231 LOCKING COLLAR 2 27 P15232 CYLINDER PLATE SQUARE 2 28 P15233 RAM POINT - UPPER 1 29 P16052 LEVELLING BEAM 2310mm 1 30 P16348 LEVELLING BOARD TIE

134 134

135 AS3516 LEVELLING BOARD - 7.2m RH OUTER ITEM PART NO DESCRIPTION QTY COMMENTS 1 P00006 BOLT M12x80 GR P01224 BOLT M20x180 GR P01281 BOLT M12x100 GR P01619 BOLT U M20 GR x P02007 NUT LOCK M P02009 NUT LOCK M P02483 LYNCH PIN CAT P02601 WASHER FLAT M P02603 WASHER FLAT M P03088 BOLT M12x60 GR P04126 BUSH SPRUNG - Ø32xØ26x P07545 PLASTIC END CAP 60x P07724 PIN Ø25x P08013 CYLINDER - Ø63x P08802 SHIM KIT 7 PIECE 1 16 P09400 SHIM KIT PLATE Ø1¼" ROD 1 17 P12675 UPPER RAM POINT 1 18 P12677 LEVELLING BOARD PILLAR 2 19 P13402 LEAF CLAMP 60x60 RHS 6 20 P13406 BOLT M10x35 DOME SQ P13407 NUT TOOTHED M P13416 SPRUNG LEAF 80x P13417 WEAR PLATE 80mm 6 24 P15230 PILLAR DISC - SQUARE 1 25 P15231 LOCKING COLLAR 2 26 P15232 CYLINDER PLATE SQUARE 2 27 P16035 LEVELLING BEAM 1320mm

136 (170) ASSEMBLY ISSUE A AS3515 PART NO. FROM SERIAL NO. TO SERIAL NO. PJG 29/07/ SIMBA DATE:- MACHINE:- DESCRIPTION:- DRAWN:- UNIPRESS 7.2m LEVELLING BOARD ASSEMBLY LH OUTER ITEM PART P13406 P13402 P02007 P04126 P12677 P03088 P12675 P09400 P01619 P16659 P02603 P15232 P01281 P15231 P02601 P08802 P15230 P02483 P08013 P01224 P13417 P13416 P02009 P07724 P13407 P00006 P07545 NO ISSUE C B A BOLT PLASTIC BUSH LEAF UPPER WASHER SHIM LEVELLING CYLINDER LOCKING PILLAR LYNCH WEAR SPRUNG PIN NUT Ø25x100 TOOTHED CLAMP KIT M10x35 M12x60 U M12x100 M20x180 M12x80 SPRUNG PLATE PIN RAM DISC END DESCRIPTION LEAF 7 FLAT COLLAR PLATE - PIECE CAT BOARD BEAM Ø63x130 GR8.8 POINT - 60x60 DOME GR. 80mm CAP SQUARE 80x10 M20 M12 M10-1 Ø1¼" Ø32xØ26x SQUARE 1080mm 60x60 145x RHS PILLAR SQ. - ROD ABS Low Steel, Abro EN 50B 45 Alloy Plastic High MATERIAL / EN CrBo 43C 251A58 / S355JR 8 Strength QTY TITLE J C/W M8x60 COMMENTS + LOCK NUT F P H B CATEGORY COST MASS Kg KN HENDRY FARM PRODUCTS POWER COMPANY

137 AS3515 LEVELLING BOARD - 7.2m LH OUTER ITEM PART NO DESCRIPTION QTY COMMENTS 1 P00006 BOLT M12x80 GR P01224 BOLT M20x180 GR P01281 BOLT M12x100 GR P01619 BOLT U M20 GR x P02007 NUT LOCK M P02009 NUT LOCK M P02483 LYNCH PIN CAT P02601 WASHER FLAT M P02603 WASHER FLAT M P03088 BOLT M12x60 GR P04126 BUSH SPRUNG - Ø32xØ26x P07545 PLASTIC END CAP 60x P07724 PIN Ø25x P08013 CYLINDER - Ø63x P08802 SHIM KIT 7 PIECE 1 16 P09400 SHIM KIT PLATE Ø1¼" ROD 1 17 P12675 UPPER RAM POINT 1 18 P12677 LEVELLING BOARD PILLAR 2 19 P13402 LEAF CLAMP 60x60 RHS 5 20 P13406 BOLT M10x35 DOME SQ P13407 NUT TOOTHED M P13416 SPRUNG LEAF 80x P13417 WEAR PLATE 80mm 5 24 P15230 PILLAR DISC - SQUARE 1 25 P15231 LOCKING COLLAR 2 26 P15232 CYLINDER PLATE SQUARE 2 27 P16659 LEVELLING BEAM 1080mm

138 138

139 AS2829 LEVELLING BOARD ASSEMBLY RH INNER UNIPRESS 8.2m ITEM PART NO DESCRIPTION QTY COMMENTS 1 P00006 BOLT M12x80 GR P01281 BOLT M12x100 GR P01619 BOLT U M20 GR x P02007 NUT LOCK M P02008 NUT LOCK M P02009 NUT LOCK M P02483 LYNCH PIN CAT P02601 WASHER FLAT M P02602 WASHER FLAT M P02603 WASHER FLAT M P03088 BOLT M12x60 GR P04126 BUSH SPRUNG - Ø32xØ26x P06802 BOLT U M16 GR x P07545 PLASTIC END CAP 60x P07724 PIN Ø25x P08013 CYLINDER - Ø63x P08802 SHIM KIT 7 PIECE 1 18 P09400 SHIM KIT PLATE Ø1¼" ROD 1 19 P12677 LEVELLING BOARD PILLAR 2 20 P13402 LEAF CLAMP 60x60 RHS 8 21 P13406 BOLT M10x35 DOME SQ P13407 NUT TOOTHED M P13416 SPRUNG LEAF 80x P13417 WEAR PLATE 80mm 8 25 P15230 PILLAR DISC - SQUARE 1 26 P15231 LOCKING COLLAR 2 27 P15232 CYLINDER PLATE SQUARE 2 28 P15233 RAM POINT - UPPER 1 29 P15261 LEVELLING BEAM 1850mm

140 140

141 AS2831 LEVELLING BOARD ASSEMBLY LH INNER UNIPRESS 8.2m ITEM PART NO DESCRIPTION QTY COMMENTS 1 P00006 BOLT M12x80 GR P01281 BOLT M12x100 GR P01619 BOLT U M20 GR x P02007 NUT LOCK M P02008 NUT LOCK M P02009 NUT LOCK M P02483 LYNCH PIN CAT P02601 WASHER FLAT M P02602 WASHER FLAT M P02603 WASHER FLAT M P03088 BOLT M12x60 GR P04126 BUSH SPRUNG - Ø32xØ26x P06802 BOLT U M16 GR x P07545 PLASTIC END CAP 60x P07724 PIN Ø25x P08013 CYLINDER - Ø63x P08802 SHIM KIT 7 PIECE 1 18 P09400 SHIM KIT PLATE Ø1¼" ROD 1 19 P12677 LEVELLING BOARD PILLAR 2 20 P13402 LEAF CLAMP 60x60 RHS 9 21 P13406 BOLT M10x35 DOME SQ P13407 NUT TOOTHED M P13416 SPRUNG LEAF 80x P13417 WEAR PLATE 80mm 9 25 P15230 PILLAR DISC - SQUARE 1 26 P15231 LOCKING COLLAR 2 27 P15232 CYLINDER PLATE SQUARE 2 28 P15233 RAM POINT - UPPER 1 29 P15234 LEVELLING BEAM 2080mm

142 ISSUE A A DESCRIPTION:- LEVELLING BOARD ASSEMBLY RH OUTER DESCRIPTION MATERIAL BOLT M12x80 GR. 8.8 Steel, High Strength Low Alloy BOLT M12x100 GR. 8.8 Steel, High Strength Low Alloy TITLE MACHINE:- UNIPRESS 8.2m QTY SIMBA 2007 COMMENTS 28 9 DRAWN:- DATE: (1805) ARH 08/12/2006 PART NO. FROM SERIAL NO. TO SERIAL NO. CATEGORY COST MASS Kg COMPANY B ASSEMBLY ISSUE AS2830 B B 142 PART NO P00006 P01281

143 AS2830 LEVELLING BOARD ASSEMBLY RH OUTER UNIPRESS 8.2m ITEM PART NO DESCRIPTION QTY COMMENTS 1 P00006 BOLT M12x80 GR P01281 BOLT M12x100 GR P01619 BOLT U M20 GR x P02007 NUT LOCK M P02008 NUT LOCK M P02009 NUT LOCK M P02483 LYNCH PIN CAT P02601 WASHER FLAT M P02602 WASHER FLAT M P02603 WASHER FLAT M P03088 BOLT M12x60 GR P04126 BUSH SPRUNG - Ø32xØ26x P06802 BOLT U M16 GR x P07545 PLASTIC END CAP 60x P07724 PIN Ø25x P08013 CYLINDER - Ø63x P08802 SHIM KIT 7 PIECE 1 18 P09400 SHIM KIT PLATE Ø1¼" ROD 1 19 P12677 LEVELLING BOARD PILLAR 2 20 P13402 LEAF CLAMP 60x60 RHS 9 21 P13406 BOLT M10x35 DOME SQ P13407 NUT TOOTHED M P13416 SPRUNG LEAF 80x P13417 WEAR PLATE 80mm 9 25 P15230 PILLAR DISC - SQUARE 1 26 P15231 LOCKING COLLAR 2 27 P15232 CYLINDER PLATE SQUARE 2 28 P15233 RAM POINT - UPPER 1 29 P15235 LEVELLING BEAM 2000mm 1 30 P16348 LEVELLING BOARD TIE

144 144

145 AS2832 LEVELLING BOARD ASSEMBLY LH OUTER UNIPRESS 8.2m ITEM PART NO DESCRIPTION QTY COMMENTS 1 P00006 BOLT M12x80 GR P01281 BOLT M12x100 GR P01619 BOLT U M20 GR x P02007 NUT LOCK M P02008 NUT LOCK M P02009 NUT LOCK M P02483 LYNCH PIN CAT P02601 WASHER FLAT M P02602 WASHER FLAT M P02603 WASHER FLAT M P03088 BOLT M12x60 GR P04126 BUSH SPRUNG - Ø32xØ26x P06802 BOLT U M16 GR x P07545 PLASTIC END CAP 60x P07724 PIN Ø25x P08013 CYLINDER - Ø63x P08802 SHIM KIT 7 PIECE 1 18 P09400 SHIM KIT PLATE Ø1¼" ROD 1 19 P12677 LEVELLING BOARD PILLAR 2 20 P13402 LEAF CLAMP 60x60 RHS 9 21 P13406 BOLT M10x35 DOME SQ P13407 NUT TOOTHED M P13416 SPRUNG LEAF 80x P13417 WEAR PLATE 80mm 9 25 P15230 PILLAR DISC - SQUARE 1 26 P15231 LOCKING COLLAR 2 27 P15232 CYLINDER PLATE SQUARE 2 28 P15233 RAM POINT - UPPER 1 29 P15235 LEVELLING BEAM 2000mm 1 30 P16348 LEVELLING BOARD TIE

146 146

147 AS4163 DD700 ROLL ASSEMBLY RH - 4.6m ITEM PART NO DESCRIPTION QTY COMMENTS 1 AS1217 AXLE ASSEMBLY - DD RINGS 1 2 P02008 NUT LOCK M16 'TYPE T' 14 3 P02037 WASHER SPRING M P02602 WASHER FLAT M P04179 WASHER FLAT M12 Ø P06802 BOLT U M16 GR x P09558 SCRAPER PLATE 7 8 P09559 SCRAPER STEM RH 1 9 P09560 SCRAPER STEM LH 6 10 P10029 SCRAPER 1 1/ P10870 BOLT M12x30 GR

148 148

149 AS4164 DD700 ROLL ASSEMBLY LH - 4.6m ITEM PART NO DESCRIPTION QTY COMMENTS 1 AS1217 AXLE ASSEMBLY - DD RINGS 1 2 P02008 NUT LOCK M16 'TYPE T' 14 3 P02037 WASHER SPRING M P02602 WASHER FLAT M P04179 WASHER FLAT M12 Ø P06802 BOLT U M16 GR x P09558 SCRAPER PLATE 7 8 P09559 SCRAPER STEM RH 6 9 P09560 SCRAPER STEM LH 1 10 P10029 SCRAPER 1 1/ P10870 BOLT M12x30 GR

150 150

151 AS4165 DD700 ROLL ASSEMBLY RH - 5.5m ITEM PART NO DESCRIPTION QTY COMMENTS 1 AS0643 AXLE ASSEMBLY - DD700 7 RINGS 1 2 AS0775 AXLE ASSEMBLY - DD700 5 RINGS 1 3 P02008 NUT LOCK M16 'TYPE T' 14 4 P02037 WASHER SPRING M P02602 WASHER FLAT M P04179 WASHER FLAT M12 Ø P06802 BOLT U M16 GR x P09558 SCRAPER PLATE 9 9 P09559 SCRAPER STEM RH 1 10 P09560 SCRAPER STEM LH 6 11 P10029 SCRAPER 1 1/ P10870 BOLT M12x30 GR

152 152

153 AS4166 DD700 ROLL ASSEMBLY LH - 5.5m ITEM PART NO DESCRIPTION QTY COMMENTS 1 AS0643 AXLE ASSEMBLY - DD700 7 RINGS 1 2 AS0775 AXLE ASSEMBLY - DD700 5 RINGS 1 3 P02008 NUT LOCK M16 'TYPE T' 14 4 P02037 WASHER SPRING M P02602 WASHER FLAT M P04179 WASHER FLAT M12 Ø P06802 BOLT U M16 GR x P09558 SCRAPER PLATE 9 9 P09559 SCRAPER STEM RH 6 10 P09560 SCRAPER STEM LH 1 11 P10029 SCRAPER 1 1/ P10870 BOLT M12x30 GR

154 154

155 AS4169 DD700 ROLL ASSEMBLY RH - 6.6m ITEM PART NO DESCRIPTION QTY COMMENTS 1 AS0643 AXLE ASSEMBLY - DD700 7 RINGS 2 2 P02008 NUT LOCK M16 'TYPE T' 18 3 P02037 WASHER SPRING M P02602 WASHER FLAT M P04179 WASHER FLAT M12 Ø P06802 BOLT U M16 GR x P09558 SCRAPER PLATE 11 8 P09559 SCRAPER STEM RH 1 9 P09560 SCRAPER STEM LH 8 10 P10029 SCRAPER 1 1/ P10870 BOLT M12x30 GR

156 156

157 AS4170 DD700 ROLL ASSEMBLY LH - 6.6m ITEM PART NO DESCRIPTION QTY COMMENTS 1 AS0643 AXLE ASSEMBLY - DD700 7 RINGS 2 2 P02008 NUT LOCK M16 'TYPE T' 18 3 P02037 WASHER SPRING M P02602 WASHER FLAT M P04179 WASHER FLAT M12 Ø P06802 BOLT U M16 GR x P09558 SCRAPER PLATE 11 8 P09559 SCRAPER STEM RH 8 9 P09560 SCRAPER STEM LH 1 10 P10029 SCRAPER 1 1/ P10870 BOLT M12x30 GR

158 158

159 AS4171 DD700 ROLL ASSEMBLY RH - 7.2m ITEM PART NO DESCRIPTION QTY COMMENTS 1 AS0953 AXLE ASSEMBLY - DD700 8 RINGS 2 2 P02008 NUT LOCK M16 'TYPE T' 22 3 P02037 WASHER SPRING M P02602 WASHER FLAT M P04179 WASHER FLAT M12 Ø P06802 BOLT U M16 GR x P09558 SCRAPER PLATE 13 8 P09559 SCRAPER STEM RH 1 9 P09560 SCRAPER STEM LH P10029 SCRAPER 1 1/ P10870 BOLT M12x30 GR

160 160

161 AS4172 DD700 ROLL ASSEMBLY LH - 7.2m ITEM PART NO DESCRIPTION QTY COMMENTS 1 AS0643 AXLE ASSEMBLY - DD700 7 RINGS 1 2 AS0953 AXLE ASSEMBLY - DD700 8 RINGS 1 3 P02008 NUT LOCK M16 'TYPE T' 20 4 P02037 WASHER SPRING M P02602 WASHER FLAT M P04179 WASHER FLAT M12 Ø P06802 BOLT U M16 GR x P09558 SCRAPER PLATE 12 9 P09559 SCRAPER STEM RH 9 10 P09560 SCRAPER STEM LH 1 11 P10029 SCRAPER 1 1/ P10870 BOLT M12x30 GR

162 162

163 AS4173 DD700 ROLL ASSEMBLY RH - 8.2m ITEM PART NO DESCRIPTION QTY COMMENTS 1 AS1208 AXLE ASSEMBLY - DD700 9 RINGS 2 2 P02008 NUT LOCK M16 'TYPE T' 26 3 P02037 WASHER SPRING M P02602 WASHER FLAT M P04179 WASHER FLAT M12 Ø P06802 BOLT U M16 GR x P09558 SCRAPER PLATE 15 8 P09559 SCRAPER STEM RH 2 9 P09560 SCRAPER STEM LH P10029 SCRAPER 1 1/ P10870 BOLT M12x30 GR

164 164

165 AS4174 DD700 ROLL ASSEMBLY LH - 8.2m ITEM PART NO DESCRIPTION QTY COMMENTS 1 AS1208 AXLE ASSEMBLY - DD700 9 RINGS 2 2 P02008 NUT LOCK M16 'TYPE T' 26 3 P02037 WASHER SPRING M P02602 WASHER FLAT M P04179 WASHER FLAT M12 Ø P06802 BOLT U M16 GR x P09558 SCRAPER PLATE 15 8 P09559 SCRAPER STEM RH 11 9 P09560 SCRAPER STEM LH 2 10 P10029 SCRAPER 1 1/ P10870 BOLT M12x30 GR

166 166

167 AS0775 AXLE ASSEMBLY DD700 5 RINGS ITEM PART NO DESCRIPTION QTY COMMENTS 1 AS0658 PILLAR ASSEMBLY DD P07727 AXLE Ø60x P08190 DD NUT SPOOL 2 4 P08994 DD RING Ø P08191 DD INTERNAL SPACER 5 6 P08189 DD BEARING SPOOL 4 7 P08188 DD SPOOL 2 8 P02489 PIN SPLIT Ø10x P01698 NUT CASTLE M

168 168

169 AS0643 AXLE ASSEMBLY DD700 7 RINGS ITEM PART NO DESCRIPTION QTY COMMENTS 1 AS0658 PILLAR ASSEMBLY DD P07729 AXLE Ø60x P08190 DD NUT SPOOL 2 4 P08994 DD RING Ø P08191 DD INTERNAL SPACER 7 6 P08189 DD BEARING SPOOL 4 7 P08188 DD SPOOL 4 8 P02489 PIN SPLIT Ø10x P01698 NUT CASTLE M

170 170

171 AS0953 AXLE ASSEMBLY DD700 8 RINGS ITEM PART NO DESCRIPTION QTY COMMENTS 1 AS0658 PILLAR ASSEMBLY DD P07730 AXLE Ø60x P08190 DD NUT SPOOL 2 4 P08994 DD RING Ø P08191 DD INTERNAL SPACER 8 6 P08189 DD BEARING SPOOL 4 7 P08188 DD SPOOL 5 8 P02489 PIN SPLIT Ø10x P01698 NUT CASTLE M

172 172

173 AS1208 AXLE ASSEMBLY DD700 9 RINGS ITEM PART NO DESCRIPTION QTY COMMENTS 1 AS0658 PILLAR ASSEMBLY DD P07731 AXLE Ø60x P08190 DD NUT SPOOL 2 4 P08994 DD RING Ø P08191 DD INTERNAL SPACER 9 6 P08189 DD BEARING SPOOL 4 7 P08188 DD SPOOL 6 8 P02489 PIN SPLIT Ø10x P01698 NUT CASTLE M

174 174

175 AS1217 AXLE ASSEMBLY DD RINGS ITEM PART NO DESCRIPTION QTY COMMENTS 1 AS0658 PILLAR ASSEMBLY DD P10349 AXLE Ø60x P08190 DD NUT SPOOL 2 4 P08994 DD RING Ø P08191 DD INTERNAL SPACER 10 6 P08189 DD BEARING SPOOL 4 7 P08188 DD SPOOL 7 8 P02489 PIN SPLIT Ø10x P01698 NUT CASTLE M

176 176

177 AS0658 PILLAR ASSEMBLY DD ITEM PART NO DESCRIPTION QTY COMMENTS 1 P07696 PRESS ROLL PILLAR 1 2 P05431 BEARING - PRESSED STEEL 1 3 P08276 GREASE PIPE 1 4 P08450 BEARING GUARD 1 5 P08298 SPACER 10mm 2 6 P00057 BOLT M16x60 GR P02602 WASHER FLAT M P02008 NUT LOCK M P01704 BOLT M16x50 GR P02603 WASHER FLAT M P02009 NUT LOCK M P01619 BOLT U M20 GR x

178 178

179 AS3708 AIR BRAKE CIRCUIT LAYOUT ITEM PART NO DESCRIPTION QTY COMMENTS 1 P01709 NUT STAYTIGHT M P02035 WASHER SPRING M P02600 WASHER FLAT M P02602 WASHER FLAT M P05400 WASHER FLAT M6 4 6 P05534 NUT LOCK M P05535 WASHER FLAT M8 4 8 P06403 BOLT M10x20 GR P09597 BOLT M8x25 GR P12349 BOLT M6x P12690 BOLT M10x30 GR P13248 BRAKE CHAMBER OIL/AIR 2 13 P13563 NUT PLAIN M P13733 BLANKING CAP 3/8" 2 15 P14497 AIR TANK 20L 1 16 P14540 DUST CAP 1 17 P14542 AIR TANK DRAIN 1 18 P14544 AIR HOSE FITTING M P14547 AIR HOSE FITTING M P15209 PALM COUPLER STOWAGE 2 21 P15210 INLINE AIR FILTER 2 22 P15214 RELAY-EMERGENCY VALVE 1 23 P15222 YELLOW AIR LINE 1 24 P15223 RED AIR LINE 1 25 P15224 SHUNT VALVE 1 26 P15225 PALM COUPLING 2 27 P15503 BLANKING PLUG - M P15506 STR FITTING - M P15533 M/F REDUCER - M22-M P15540 TEST POINT M P15874 AIR VALVE TOP PLATE 1 32 P17055 AIR TANK BRACKET 2 33 P17186 CHAMBER HOSE 806mm 1 34 P17187 CHAMBER HOSE 1373mm

180 DESCRIPTION:- UNIPRESS HYDRAULIC BRAKES CIRCUIT LAYOUT MACHINE:- UNIPRESS 3 SIMBA 2009 DRAWN:- DATE:- 10 KSL 25/05/ PART NO. FROM SERIAL NO. TO SERIAL NO ASSEMBLY ISSUE AS3717 B 180

181 AS3717 HYDRAULIC BRAKES CIRCUIT LAYOUT ITEM PART NO DESCRIPTION QTY COMMENTS 1 P02263 DOWTY SEAL ½" BSP 1 2 P04513 ADAPTOR MALE-MALE ½" BSP 1 3 P /8" BSP BULKHEAD 1 4 P09318 T ADAPTOR 3/8" BSP 1 5 P09544 CAP FEMALE - BLUE 1 6 P10128 ISO BRAKE COUPLING - FEM 1 7 P10293 BOLT M6x20 GR P13248 BRAKE CHAMBER OIL/AIR 2 9 P15503 BLANKING PLUG - M P15925 BRAKE QRC STOWAGE 1 11 P17189 HA 3/8"X380 F/F P17190 HA 3/8"X2300 F/F 1 13 P18114 HA 3/8"X5050 F/F

182 182

183 AS3051 DRAWBAR CIRCUIT - 4.6m - 8.2m ITEM PART NO DESCRIPTION QTY COMMENTS 1 P01055 CYLINDER - Ø5"x P00179 HA 1/2"x P00181 HA 1/2"x P00200 BANJO BLOCK ½" BSP 2 5 P00201 BANJO BOLT ½" BSP 2 6 P00203 ADAPTOR MALE-MALE ½" BSP 4 7 P00205 QUICK RELEASE MALE - ½" BSP 2 8 P00206 ADAPTOR MALE-FEM ½" BSP 2 9 P00774 SHUT OFF TAP ½" BSP 2 10 P02263 DOWTY SEAL ½" BSP P02735 BULKHEAD ½" BSP 2 12 P07947 HA 1/2"x P09539 CAP FOR MALE - RED

184 184

185 AS3053 WING CIRCUIT HYDRAULICS - 4.6m & 5.5m ITEM PART NO DESCRIPTION QTY COMMENTS 1 P00166 CYLINDER - Ø75x P00181 HA 1/2"x P00183 HA 1/2"x P00200 BANJO BLOCK ½" BSP 8 5 P00201 BANJO BOLT ½" BSP 8 6 P00202 ADAPTOR FEM - FEM ½" BSP 4 7 P00203 ADAPTOR MALE-MALE ½" BSP 7 8 P00205 QUICK RELEASE MALE - ½" BSP 2 9 P00209 ADAPTOR 4 WAY ½" BSP 4 10 P02263 DOWTY SEAL ½" BSP P02733 ELBOW 1/2" BSP - F-F 1 12 P02735 BULKHEAD ½" BSP 6 13 P02741 DOWTY SEAL ¼" BSP 1 14 P03687 DOWTY SEAL 3/8" BSP 3 15 P05910 BLANKING PLUG 1/4" BSP 1 16 P06219 BLANKING PLUG ½" BSP 1 17 P07977 BLANKING PLUG 3/8" BSP 3 18 P08516 GAUGE ADAPTOR ¼" BSP 1 19 P08838 ACCUMULATOR 1.4L DIAPHRAGM 10b 1 20 P09537 CAP FOR MALE - YELLOW 2 21 P09968 HA 1/2"x P09970 HA 1/2"x P10328 HA 1/2"x P11767 HA 1/2"x P11785 ACCUMULATOR 0.7L 10 BAR 1 26 P12017 PRESSURE GAUGE 0-100BAR 1 27 P12056 DOC + PR RED. MANIFOLD 1 28 P12937 HA 1/2"x

186 186

187 AS3054 WING CIRCUIT HYDRAULICS - 6.1m-8.2m ITEM PART NO DESCRIPTION QTY COMMENTS 1 P00181 HA 1/2"x P00183 HA 1/2"x P00200 BANJO BLOCK ½" BSP 8 4 P00201 BANJO BOLT ½" BSP 8 5 P00202 ADAPTOR FEM - FEM ½" BSP 4 6 P00203 ADAPTOR MALE-MALE ½" BSP 7 7 P00205 QUICK RELEASE MALE - ½" BSP 2 8 P00209 ADAPTOR 4 WAY ½" BSP 4 9 P02263 DOWTY SEAL ½" BSP P02733 ELBOW 1/2" BSP - F-F 1 11 P02735 BULKHEAD ½" BSP 6 12 P02741 DOWTY SEAL ¼" BSP 1 13 P03687 DOWTY SEAL 3/8" BSP 3 14 P05910 BLANKING PLUG 1/4" BSP 1 15 P06219 BLANKING PLUG ½" BSP 1 16 P07977 BLANKING PLUG 3/8" BSP 3 17 P08516 GAUGE ADAPTOR ¼" BSP 1 18 P08838 ACCUMULATOR 1.4L DIAPHRAGM 10b 1 19 P09537 CAP FOR MALE - YELLOW 2 20 P09968 HA 1/2"x P09970 HA 1/2"x P10328 HA 1/2"x P11767 HA 1/2"x P11785 ACCUMULATOR 0.7L 10 BAR 1 25 P12017 PRESSURE GAUGE 0-100BAR 1 26 P12056 DOC + PR RED. MANIFOLD 1 27 P12937 HA 1/2"x P00164 CYLINDER - Ø3¾"x

188 188

189 AS3056 LEVELLING BOARD HYDRAULIC CIRCUIT - 4.6m & 5.5m ITEM PART NO DESCRIPTION QTY COMMENTS 1 P00181 HA 1/2"x P00183 HA 1/2"x P00203 ADAPTOR MALE-MALE ½" BSP 2 4 P00205 QUICK RELEASE MALE - ½" BSP 2 5 P02263 DOWTY SEAL ½" BSP 2 6 P02735 BULKHEAD ½" BSP 4 7 P03687 DOWTY SEAL 3/8" BSP 11 8 P08013 CYLINDER - Ø63x P08362 BANJO BLOCK 3/8" COMPLETE 4 10 P09314 MALE - MALE ADAPTOR 3/8" BSP 5 11 P /8" BSP BULKHEAD 6 12 P09317 HA 3/8x P09318 T ADAPTOR 3/8" BSP 1 14 P09319 HA 3/8x P09422 VALVE FDC VDFR /8" 1 16 P09423 COUNTERBALANCE VALVE 2 17 P09545 CAP FOR MALE - ORANGE 2 18 P09972 HA 3/8"-1/2"x P10862 HA 3/8x

190 190

191 AS3055 LEVELLING BOARD HYDRAULIC CIRCUIT 6.6m ITEM PART NO DESCRIPTION QTY COMMENTS 1 P00181 HA 1/2"x P00183 HA 1/2"x P00203 ADAPTOR MALE-MALE ½" BSP 2 4 P00205 QUICK RELEASE MALE - ½" BSP 2 5 P02263 DOWTY SEAL ½" BSP 2 6 P02735 BULKHEAD ½" BSP 4 7 P03687 DOWTY SEAL 3/8" BSP 11 8 P08013 CYLINDER - Ø63x P08362 BANJO BLOCK 3/8" COMPLETE 4 10 P09314 MALE - MALE ADAPTOR 3/8" BSP 5 11 P /8" BSP BULKHEAD 6 12 P09317 HA 3/8x P09318 T ADAPTOR 3/8" BSP 1 14 P09319 HA 3/8x P09422 VALVE FDC VDFR /8" 1 16 P09423 COUNTERBALANCE VALVE 2 17 P09545 CAP FOR MALE - ORANGE 2 18 P10862 HA 3/8x P17537 HA 3/8"-1/2"x1050 F/F 1 20 P17538 HA 3/8"-1/2"x1310 F/F

192 192

193 AS3312 LEVELLING BOARD HYDRAULIC CIRCUIT UNIPRESS 7.2m & 8.2m ITEM PART NO DESCRIPTION QTY COMMENTS 1 P00181 HA 1/2"x P00183 HA 1/2"x P00203 ADAPTOR MALE-MALE ½" BSP 2 4 P00205 QUICK RELEASE MALE - ½" BSP 2 5 P02263 DOWTY SEAL ½" BSP 2 6 P02735 BULKHEAD ½" BSP 4 7 P03687 DOWTY SEAL 3/8" BSP 27 8 P08013 CYLINDER - Ø63x P08362 BANJO BLOCK 3/8" COMPLETE 4 10 P09314 MALE - MALE ADAPTOR 3/8" BSP 5 11 P /8" BSP BULKHEAD 6 12 P09317 HA 3/8x P09318 T ADAPTOR 3/8" BSP 5 14 P09319 HA 3/8x P09422 VALVE FDC VDFR /8" 1 16 P09423 COUNTERBALANCE VALVE 2 17 P09545 CAP FOR MALE - ORANGE 2 18 P11043 HA 3/8"-1/2"x P13685 HA 3/8x m ONLY 20 P13690 HA 3/8x m ONLY 21 P16054 HA 3/8x

194 194

195 AS3058 REAR DRAWBAR LIFT CIRCUIT 4.2m - 8.2m ITEM PART NO DESCRIPTION QTY COMMENTS 1 P00160 CYLINDER - Ø3¾"x9" P00176 HA 1/2"x P00177 HA 1/2"x P00185 HA 1/2"x P00187 HA 1/2"x P00200 BANJO BLOCK ½" BSP 2 7 P00201 BANJO BOLT ½" BSP 2 8 P00203 ADAPTOR MALE-MALE ½" BSP 4 9 P00206 ADAPTOR MALE-FEM ½" BSP 2 10 P00774 SHUT OFF TAP ½" BSP 4 11 P02263 DOWTY SEAL ½" BSP P02730 QUICK RELEASE FEM. ½" BSP 2 13 P02734 ELBOW MALE-FEM COMPACT ½" BSP 4 14 P02735 BULKHEAD ½" BSP 2 15 P06216 ADAPTOR T SFOR ½" BSP 4 16 P09540 CAP FEMALE - RED

196 196

197 AS3059 REAR DRAWBAR WING CIRCUIT ITEM PART NO DESCRIPTION QTY COMMENTS 1 P00182 HA 1/2"x P00203 ADAPTOR MALE-MALE ½" BSP 2 3 P00774 SHUT OFF TAP ½" BSP 2 4 P02263 DOWTY SEAL ½" BSP 4 5 P02730 QUICK RELEASE FEM. ½" BSP 2 6 P02734 ELBOW MALE-FEM COMPACT ½" BSP 2 7 P02735 BULKHEAD ½" BSP 2 8 P06216 ADAPTOR T SFOR ½" BSP 2 9 P09538 CAP FEMALE - YELLOW

198 198

199 AS3743 STICKER KIT - UNIPRESS 4.6m ITEM PART NO DESCRIPTION QTY COMMENTS 1 P08923 DECAL - DD SMALL 2 2 P11643 DECAL - FALLING WINGS 2 3 P11645 DECAL - HAND TRAP 6 4 P11694 DECAL - GREASE 10 HOURS 4 5 P11695 DECAL - GREASE 50 HOURS 6 6 P11700 DECAL - MADE GREAT 2 7 P12558 DECAL - AXLE TENSION 2 8 P15266 DECAL - 4.6m 2 9 P16755 DECAL-SIMBA GP 130X P17235 DECAL - HAND TRAP SMALL 2 11 P17237 DECAL-UNIPRESS 2 12 P17238 DECAL-SIMBA DASH GP 2 13 P17239 DECAL-DASH SIMBA GP 2 14 P17241 DECAL-GROUP WARNING

200 200

201 AS4011 STICKER KIT - UNIPRESS 5.5m ITEM PART NO DESCRIPTION QTY COMMENTS 1 P08923 DECAL - DD SMALL 2 2 P11643 DECAL - FALLING WINGS 2 3 P11645 DECAL - HAND TRAP 6 4 P11694 DECAL - GREASE 10 HOURS 8 5 P11695 DECAL - GREASE 50 HOURS 6 6 P11700 DECAL - MADE GREAT 2 7 P12558 DECAL - AXLE TENSION 2 8 P15267 DECAL - 5.5m 2 9 P16755 DECAL-SIMBA GP 130X P17235 DECAL - HAND TRAP SMALL 2 11 P17237 DECAL-UNIPRESS 2 12 P17238 DECAL-SIMBA DASH GP 2 13 P17239 DECAL-DASH SIMBA GP 2 14 P17241 DECAL-GROUP WARNING

202 202

203 AS4013 STICKER KIT - UNIPRESS 6.6m ITEM PART NO DESCRIPTION QTY COMMENTS 1 P08923 DECAL - DD SMALL 2 2 P11643 DECAL - FALLING WINGS 2 3 P11645 DECAL - HAND TRAP 6 4 P11694 DECAL - GREASE 10 HOURS 8 5 P11695 DECAL - GREASE 50 HOURS 6 6 P11700 DECAL - MADE GREAT 2 7 P12558 DECAL - AXLE TENSION 2 8 P15268 DECAL - 6.6m 2 9 P16755 DECAL-SIMBA GP 130X P17235 DECAL - HAND TRAP SMALL 2 11 P17237 DECAL-UNIPRESS 2 12 P17238 DECAL-SIMBA DASH GP 2 13 P17239 DECAL-DASH SIMBA GP 2 14 P17241 DECAL-GROUP WARNING

204 204

205 AS4014 STICKER KIT - UNIPRESS 7.2m ITEM PART NO DESCRIPTION QTY COMMENTS 1 P08923 DECAL - DD SMALL 2 2 P11643 DECAL - FALLING WINGS 2 3 P11645 DECAL - HAND TRAP 6 4 P11694 DECAL - GREASE 10 HOURS 8 5 P11695 DECAL - GREASE 50 HOURS 6 6 P11700 DECAL - MADE GREAT 2 7 P12558 DECAL - AXLE TENSION 2 8 P16755 DECAL-SIMBA GP 130X P17235 DECAL - HAND TRAP SMALL 2 10 P17237 DECAL-UNIPRESS 2 11 P17238 DECAL-SIMBA DASH GP 2 12 P17239 DECAL-DASH SIMBA GP 2 13 P17264 DECAL - GROUP OF 6 WARNING 1 14 P17504 DECAL - 7.2m

206 206

207 AS4016 STICKER KITS - UNIPRESS 8.2m ITEM PART NO DESCRIPTION QTY COMMENTS 1 P08923 DECAL - DD SMALL 2 2 P11643 DECAL - FALLING WINGS 2 3 P11645 DECAL - HAND TRAP 6 4 P11694 DECAL - GREASE 10 HOURS 8 5 P11695 DECAL - GREASE 50 HOURS 6 6 P11700 DECAL - MADE GREAT 2 7 P12328 DECAL - 8.2m 2 8 P12558 DECAL - AXLE TENSION 2 9 P16755 DECAL-SIMBA GP 130X P17235 DECAL - HAND TRAP SMALL 2 11 P17237 DECAL-UNIPRESS 2 12 P17238 DECAL-SIMBA DASH GP 2 13 P17239 DECAL-DASH SIMBA GP 2 14 P17264 DECAL - GROUP OF 6 WARNING

208 208

209

210 Woodbridge Road, Sleaford Lincolnshire, NG34 7EW T F E simba.international@simba.co.uk W