FLT-Appendix E. Vendor Item 2017 Tandem Axle Combination Vacuum- Record Specification/ State Alternative

Transcription

1 1.00 Engine Yes No H.P. water cooled 4 cycle diesel 2016 OBD EPA CARB GHG 17 compliant 1.02 Minimum 1550 lb./ft. at 975 RPM torque 1.03 Warranty - State coverage for engine offered 1.04 Air cleaner c/w air restriction indicator 1.05 Hand throttle, electronic control at instrument panel 1.06 Fan clutch, on/off air 1.07 Engine Compression brake c/w selector and on/off switch 1.08 Starter, 12 Volt 1.09 Electric engine shutdown control 1.10 Engine Protection- engine Integral warning System 1.11 Horizontal exhaust after treatment mounted on right side under cab and vertical pipe on right hand cab side 1.12 Coolant filter (spin on) c/w additive 1.13 Fuel filters cartridge style 1.14 Oil filters (spin on) 1.15 Oil cooler integral 1.16 Heavy duty radiator c/w level sight glass to be determined by GVW Silicone hoses where possible 1.18 Engine coolant, equivalent to - 40 C Watt immersed engine block heater 2.00 Electrical Yes No volt system volt starter (state type) 2.03 Minimum 150 amp alternator 2.04 Three (3) 12V batteries capacity, min total 2500 cca 2.05 Battery box mounted disconnect master switch 2.06 Covered battery box with jump start stud Automatic reset circuit breakers 2.08 Two way radio prewire with mirror mounted antenna 2.09 Backup alarm min 97DBA 2.10 Minimum two 12V cab power points 2.11 Remote Jump Start Studs 2.12 Four (4) sets of keys with FOB s 2.13 Electric horn in engine compartment 3.00 Transmission Yes No 3.01 Allison 4500 RDS, Automatic c/w PTO provision speed, close ratio 3.03 Electronic push button dash mounted, transmission selector 3.04 Oil level sensor 3.05 Torque converter to suit application 3.06 H.D. external transmission cooler 3.07 NOTE: Required "SCANN" drive train compatibility summary to be provided with bid 3.08 NOTE: A maximum 110 km/hr road speed required 3.09 State Warranty and provide detail with Tender 4.00 Axles and Drives Yes No 4.01 Meritor MFS A Wide track 20,000 lb. or equivalent 4.02 State turning radius 4.03 Power steering type (state) preference is dual box ,000 lb. multi-leaf springs 4.05 Front axle shock absorbers 4.06 Synthetic oil filled front hubs 4.07 Front hub visible oil level cap 4.08 Front brake 16.5 x 7 outboard mounted iron drum 1 OF 10

2 4.09 Front brake "Q+" series 16.5 x 7" non- asbestos 4.10 Automatic slack adjusters same brand all positions 4.11 Front brake dust shields 4.12 Meritor RT46-160P (46,000 lb.) " axle spacing c/w fore / Aft control rods 4.14 Steel walking beams, Bronze centre bushing 4.15 Rear suspension, Hendrickson RTE ,000 lb. capacity iron carrier housing 4.17 Rear axle ratio to be determined by Allison Performance SCANN to achieve optimum fuel economy and performance 4.18 Driver controlled differential lock for both axles 4.19 Inter-axle differential lock 4.20 Rear axle 16.5 x 7 outboard mounted cast drums 4.21 Q+ 16.5x7 brake shoes 4.22 Automatic slack adjusters 4.23 Four (4) #30 spring brake chambers 4.24 Brak Chek brand safety system 2 stroke indicators 4.25 Rear brake dust shield 5.01 Air System Yes No 5.02 Minimum 19CFM air compressor 5.03 Wabco SS 1200 air dryer 5.04 Drain petcocks on all tanks 5.05 Auto drain valves 5.06 Air tanks to be mounted inside frame rails 6.01 Tires Yes No 6.02 Two (2) Front; 22.5 x 12.25, 10 hole Accuride, Hub Piloted Disk, Inset for maximum steer angle (tubeless) 6.03 Eight (8) Rear; 22.5 x 8.25, 10 hole Accuride, Hub Piloted Disk (tubeless) 6.04 Two (2) Front tires; sufficient size and rating to meet maximum British Columbia GVW license specifications of final weight 6.05 Eight (8) Rear tires: 11R 22.5, Winter Deep Bridgestone VSS or equivalent. Sufficient load rating to achieve British Columbia GVW license specifications of final weight 7.00 Fuel Tank Yes No 7.01 One (1) Aluminium 80 gal. (min) driver side fuel tank 7.02 Steps to be anti-slip protected 8.00 Cab / Frame Yes No 8.01 Factory full length, double channel steel 8.02 Heat treated alloy steel frame rails with outer C channel 8.03 Two (2) front and two (2) rear tow hooks, frame mounted 8.04 H.D. front bumper 8.05 State Model and Year 8.06 State Make 8.07 Wheelbase 240" approx C.T. Approximately 160" 8.09 Conventional Cab, 110, BBC approximately 8.10 O.A.L. (state) 8.11 Scales to be installed on all axles with display in cab 8.12 Front axle G.V.W.R. 20,000 lb Rear axle G.V.W.R. 46,000 lb Total G.V.W.R. 66,000 lb Driveline Yes No Series half round main driveline Series half round inter-axle driveline 2 OF 10

3 10.00 Cab Conventional Yes No Steel or aluminium construction cab, deluxe noise suppression interior Tilt hood, one piece, sloping for good driver visibility Rubber front fender extensions Inner removable front fender liner Two (2) 7½ x 16 lighted/heated, power, mirror, west coast style " convex mirror, mounted on driver and passenger side Tinted glass all around Climate controlled cab, A/C Heavy duty floor mat High back drivers and passenger seat c/w H.D. cloth, full air ride, fully adjustable including lumbar support Driver control panel switch for passenger side door window Dual sun visor AM/FM, Bluetooth, stereo radio c/w 2 speakers Two (2) retractable seat belts Dual air horn speed, intermittent electric wipers c/w electric washer Power locks Power windows Interior cab light Video Camera Monitor in cab c/w four cameras positioned at operator station, drivers and passenger side door and one camera facing rear of Adjustable steering column Front and rear operators camera s Cruise control Driver and passenger Grab handles Instrumentation Yes No Electronic speedometer, trip odometer Tachometer Engine hour meter Engine temp gauge Engine oil pressure Warning light/buzzer low air pressure Fuel level gauge Ammeter/Voltmeter Transmission temp. gauge Primary, Secondary and Application air pressure gauges Low oil pressure/high temp. warning system c/w light and buzzer for engine Lights Yes No All lights to meet B.C. D.O.T. requirements LED Amber cab mounted marker lamps Rear signal light, stop, tail light, sealed LED lights Mid-body mounted signal lights, sealed LED lights Backup lamp, sealed LED lights Clearance lights; red and amber, sealed LED lights Licence plate lamp (rear) Self-cancelling signal light switch Traffic directional arrow boards front and rear Turn signals (fender mounted) All necessary reflectors & markers Paint Yes No Body white Basecoat, Clear coat Chassis painted black 3 OF 10

4 13.03 Wheels white Miscellaneous Yes No One (1) Parts and Maintenance Manual for Truck Chassis Two (2) Operators Manual for truck chassis Warranty Yes No Provide warranty information for truck chassis, engine, transmission and any other components related to the truck manufacturer s chassis Combination Vacuum High Pressure Sewer Cleaner Yes No Debris Tank Debris body to have a useable capacity of 10 cu.yds. or greater Debris body to have a ¼ hard surface coat of epoxy or equivalent Corrosion resistant Built to withstand 360" of water column vacuum Body to be constructed of ¼" abrasive resistant high strength steel, or approved equivalent (state) Full diameter, top hinged, hydraulically opened debris body tail gate Tail gate/rear door seal to be self compensating Neoprene and body to have splash apron/shield Rear door to have hydraulically operated, over centre tailgate latches Rear door hydraulic controls to be on drivers side, located away from rear of unit to avoid splash of contaminants when dumping waste Rear door mounted 6" knife valve connected to a high rise standpipe to drain liquids. Valve to have quick lock clamps for ease of hose removal A 6"x25' lay flat hose shall be attached to valve and be secured to door during transit Drain hose and butterfly valve to be equipped with quick lock clamps for ease of removal A second 6" knife valve with locking lever to be located at lowest point of rear door to allow for decanting of excess fluids Debris body dumping "to be raise to dump" via a 2 stage, telescopic double acting cylinder. Vacuum hose and boom must not dump with debris State Debris body minimum dump angle Tailgate to have adequate ground clearance while open and body in dumping mode (state clearance) All pivot pins to be greaseable with threaded zerks Debris tank to have exterior visible liquid level gauge Debris tank to have internal flushing system A manual debris tank safety prop, permanently mounted and hinged to frame to be supplied to support debris tank in raised position Tailgate to have permanently attached and hinged safety prop to support tailgate in open position Stainless steel check ball to be provided for vacuum system shut-off when debris tank full of liquids Hydraulic de-cant pump off system at rear tail gate plumbed to front and rear bumper with control at operator station Hydraulically operated "flapper/breaker valve" to be provided allowing the operator to pull a momentary vacuum in the debris tank in order to lift heavier material Water Storage Tank Minimum capacity of 1,300 US gals., multi-cell tanks Water tanks to be non-corrosive, repairable, polyethylene or aluminium Bottom of polyethylene tanks to be protected by ¼" steel plate Water tanks to be baffled and interconnected All water tanks to have easy access ports on top of each tank, 10" minimum 4 OF 10

5 17.06 Minimum 4" air gap on fill tube to prevent siphoning of water tank back to source Water tanks should not dump with the debris tank Water level sight glass/tube shall be installed in a location visible from operator station Low level water level alarm to be installed with light at operator station The water supply to the pump shall allow operation of water pump while debris body is in dump mode Tank shut-off valve and stainless steel removable "Y" strainer at tank filler Winter re-circulating package capable of pumping water through system including hose reel while machine in motion " connection between water tanks Low point drain valves to drain tanks completely Air purge system utilizing chassis air system Lifetime warranty against corrosion and cracking of water tanks, provide supporting certification Vacuum System (8') Yes No Vacuum pump to be positive displacement Roots type blower Model 824RCS 16 or equivalent Integrated wireless controls for all functions Drive gear reservoir to have visible oil level sight glass Vacuum pump to be driven by chassis engine Vacuum pump to be engaged via air shift or electric controls (not cable) Vacuum pump or power source not to require daily greasing Air flow through pump to be vertical to eliminate moisture trapping and/or freezing Unit to be equipped with high efficiency silencer with discharge above cab c/w protective rain cap Truck odometer not to operate when vacuum pump or water pump operating to eliminate false odometer readings Tapered cyclonic separator with debris collector box complete with cleanout door, base sloped for ease of cleaning and draining Vacuum pump to be driven by matched set of Kevlar belts, or direct driveshaft drive Unit shall be protected by two (2) vacuum relief valves, fully adjustable Cleanable/reusable pleated stainless steel cylindrical final air filter located between debris body and vacuum pump Filter screen cleaning shall not require entry into the debris body There shall be one connection between the debris body and vacuum system. This connection shall be a self aligning H.D. rubber seal Vacuum pump control switch to activate hour meter to register hours of vacuum pump use. Hour meter to be installed in cab instrument panel and labelled High Pressure Flushing Pump Yes No A triplex reciprocating plunger water pump to be provided, or single piston double acting water pump or equivalent Continuous rating of 80 GPM at 2500 psi Pressure regulator set at 2500 psi with relief to water tank Pump designed capable of operating without water for a short period without damage to pump Pump to provide continuous smooth water flow & pressure Engagement and disengagement of pump to be done from operator station State working RPM of water pump - if applicable State make and model Pump to be mounted in an easily accessible location for ease of maintenance Two (2) 2 way 1½" ball valves for sewer flushing operation. Mounted at operator control on hose reel One (1) 2 way 1½" ball valve for hose reel bypass 5 OF 10

6 19.12 Ball valves to be completely serviceable Pump shall remain flooded at all times to eliminate pump cavitation Water pump control switch to activate hour meter to register hours of water pump use. Hour meter to be installed in cab instrument panel and labelled Hand Gun/Manhole Wash Down System Yes No Unit to have a quick connect at hose reel with a relief valve set at 800 psi Operator station to have a, retractable hose reel with 50' of ½" hose, mounted to front driver side of bumper ½" hose - hose reel to be spring loaded retractable c/w detent A spray gun with adjustable/interchangeable nozzles to be provided An extra 25 reel and isolation ball valve at passenger side rear of body location to be provided c/w quick connect and be protected by 800 psi relief valve for wash down The handgun circuit control valve to be located at the operator station Ball valve to be located at wash down gun reel on front driver side of bumper Hose Reel Yes No Manufactured of ¼" spun steel, requiring no internal or external reinforcement Minimum storage of hose to be 600' of 1" sewer hose Front mounted hose reel shall telescope or tilt down to allow access to engine compartment for tilt type engine hood Reel telescope or tilt circuit to be hydraulically actuated c/w secondary manual system to operate circuit if main engine power source becomes inoperative Reel to have positive lock system on reel rotation Reel rotation to be 180 minimum Reel to never extend beyond width of truck on drivers side of unit Reel to be hydraulically driven Variable speed control for reel rotation 0-50 RPM Reel to have electronic hose footage counter Auto level wind on front hose reel Reel to have dual roller level wind gauge Unit to be supplied with 600' x 1" sewer/flush hose with 2500 psi working pressure and 6500 burst pressure Hose to come with 20' x 1" leader hose Hydraulic control valve for reel to be located at operator station Integrated wireless control for all functions water shut off valve to hose reel located at operators station V roller guides for 1 hose, hinged for guiding hose Access Panels Yes No All enclosures with hinged fully opening doors Hinged doors to have H.D. hinges and keyed alike locks Warning labels to be visible on doors warning of danger due to vacuum and water pump operation Provide storage compartments on curb side for tool storage. Compartments to be constructed with aluminum with rope lights in tool box All tool storage boxes to be vented to reduce moisture condensation on tools Ladders, steps, platforms must all be anti-slip and configured with grab handles to allow three point contact at all times for the purpose of maintaining the unit Additional heated storage cabinet configured and suitable for storing rain gear Long handle tool storage (i.e. pipe poles, rock pickers) Power Boom & Vacuum Hose Yes No 6 OF 10

7 Power boom & vacuum hose must be mounted independently of debris body and must not dump with debris body. All hoses and boom to be 8" dia The power boom shall have 180 min. rotation Boom operated by an electric over hydraulic system with hydraulics run off body manufacturer s hydraulic system All boom functions to be hydraulically actuated State boom rotation system Boom extension, rotation and lift/lower controls to be at operator station as well as on remote pendant A boom rest platform for transport to be directly mounted to body sub frame State boom vertical lift height and weight limits State boom reach from centre of pivot point Boom to be true telescoping with 8' extension Debris vacuum hose shall be supported in a cradle and attached to the steel telescopic boom tube via travis clamp connection to enable the hose to be rotated for wear Boom to be capable of lifting catch basin/manhole covers, lifting capacity in pounds Boom lift capacity to be approx. 700 lb. with identifying labels Two (2) boom mounted spot light wired to retractable cable reel for boom extension Boom control pendant functions to operate: - boom up/down - boom left/right - boom extend/retract - open/close vacuum flapper/breaker - boom flood light on/off - emergency shut down power to boom Any connection between debris body and vacuum system to be self aligning pressure fitting type Supply the following aluminium tubes with travis type clamp connections: - One (1) 4'x8" tube (extension) - Two (2) 8'x8" tube (extension) - One (1) 6'x8" tube (extension) - One (1) 6'x8" catch basin cleaner tube c/w steel tip - One (1) 8 to 6 adaptor - One (1) 8 to 4" adaptor - One (1) hydro-excavating tube Integrated wireless controls for all station functions Operator Control Centre to have the following controls: Yes No Vacuum on/off switch Water pump on/off switch Hose reel direction and speed control Reel rotation control and lock Engine electric throttle control switch Engine tachometer Emergency engine kill switch Water pressure gauge, non-freezing winter operation Vacuum gauge Water tank low level alarm/light Boom up/down rotate and telescope control Control panel to be illuminated Control for flapper/vacuum breaker valve Digital display package with diagnostic capability Electrical Systems Yes No Entire electrical system to be weather and water proof 7 OF 10

8 25.02 Two (2) rear tailgate mounted flood lights c/w cab switch to illuminate rear of unit Front and rear mounted amber beacon lights with brush guards and c/w cab mounted switch & indicator light Two (2) boom mounted spot lights c/w switch at operator station and wiring connection for hand held light One (1) flashing arrow board to be mounted at rear of unit with control panel in cab, L.E.D. lights (approx. 23 x 48 ) One (1) flashing arrow board to be mounted behind cab facing forward with control panel in cab, L.E.D. lights Rope lights to be installed in tool boxes, switch in cab High visibility LED strobe lights on fenders and bumpers Hydraulics Yes No Hydraulic drive pump: State Make: State Model: State GPM: Hydraulic reel drive motor: State Make: State Model: State GPM: State hydraulic reservoir capacity Hydraulic tank to have spin-on return filter Sufficient isolation valves to allow servicing without significant oil loss Hydraulic tank to have oil sight level glass Hydraulic control valve for reel direction to be open centre directional control with adjustable flow divider and adjustable relief Vacuum Tube Storage Yes No Pipe storage to be easily accessible Provide storage brackets to hold a minimum of six (6) tubes Tubes to be held with clamping method (state) Painting Yes No All metal surfaces shall be shot or sandblasted and primed prior to painting Cab and body and all components to be painted white Hydro Excavation Package Yes No Minimum 2300 PSI Hydro excavation handgun Handgun extensions 4 to Hydro excavation reel to be located behind cab on passenger side Lateral line reel ½ lateral line high pressure reel mounted beside hydro excavation reel Accessories Yes No One (1) hand held spotlight c/w 50' retractable cord reel mounted at operator station to front bumper One (1) tiger tail hose guide c/w 30' cord Mud flaps to be provided forward and rear of rear drive wheels Optional Equipment/Services Offered Yes No Stainless steel debris tank Digital hose reel counter Hydraulic fold down tube rack mounted on tail gate to hold 6 (six) tubes with locking device, bungee straps not acceptable Passenger side door lower window 8 OF 10

9 31.05 Three (3) days of Comprehensive Operator and Technician Training on the correct operation of Sewer Vacuum Combination unit. Training to be provided by Factory Training Personnel. Training will be for up to 8 operators Additional storage tool boxes Nozzles, Buzz bombs, etc Root cutters Auto lube system for chassis and all add on accessories Hydraulic tool circuit and reel Warranty Yes No Minimum one (1) year on sewer/catch basin cleaner on defects in material and workmanship State warranty on water tanks State warranty on debris tank State warranty on water pump State warranty on vacuum pump Provide detailed drawings indicating location of debris body, water tanks, reel, boom etc Provide details of location of tool boxes and sizes Parts, Maintenance and Operator Manuals Yes No One (1) Parts and Maintenance Manual for Combination Vacuum Flusher Body Body manufacturer to provide an operator training video or CD for the correct and safe operation of the unit as ordered Two (2) operators manuals DVD etc Delivery Date Yes No Earliest delivery from point of order Latest delivery from point of order Specifications Yes No Specifications for one (1) combination catch basin/sewer and high pressure cleaner (8" suction) Warranty Complete description of warranties to machine and attached components/equipment bidder to provide copy of warranty(s) Training Successful bidder shall provide onsite operator and maintenance staff training and cost for such training to be absorbed by bidder. Training is to be conducted by a factory representative, or a factory trained representative, for a minimum of 1 day at the time of delivery. This training shall cover all operations this machine is to perform on a daily basis. Additional training is to be provided for the equipment maintenance staff for preventative maintenance Repair Parts and Service Since the continuous operation of this equipment is of the utmost importance and sometimes of an emergency nature, it is necessary that the successful bidder be in a position to render prompt parts and service. Said parts inventory shall be of sufficient size and variety to offer a level of parts availability of 95% within 48 hours from the time of order by the customer. Availability of normal maintenance items such as filters, V belts, hydraulic lines and hoses shall not exceed 24 hours. Bidder shall attach his proposed program for parts and service availability for evaluation. Review of the bidder s ability to provide prompt parts and service could be used in determining low, qualified bidder. 9 OF 10

10 39.00 Demonstration The vendor or manufacturer of the equipment which is seriously considered for award shall, at the request of the customer, demonstrate his equipment at the location chosen by the customer and in the presence of authorized customer representatives to prove out any features which may be in question. Failure of the demonstration to meet customer requirements may be adjudged as non-conformance to these specifications. 10 OF 10