List of Machinery and Equipment for M.M.V.trade (Annexure A)

Transcription

1 List of Machinery and Equipment for M.M.V.trade (Annexure A) S.NO Name and description of article Quantity (in Nos) 1. Steel rule 15 cm inch and metric 21-No s 2. Steel rule 30 cm inch and metric -do- 3. Steel measuring tape 10 meter in a case Try Square 10 cm Blade Calipers outside 15 cm spring Calipers inside 15 cm spring Dividers 15 cm Spring Safety glasses Scriber 15 cm Knife double Blade Electrician Wire insulation Stripper for shinning 21 conductors from 0.4mm to 4mm 12. Electrician testing Pencil (Line / Neon 21 tester) 13. Electrician Screw Driver 250mm Centre punch 10 cm Chisel cold flat 20 mm x 150 mm Hammer ball peen 0.5 kg with handle Screw driver 20cm.x 9mm. Blade Screw driver 30 cm. x 9 mm. Blade Spanner D.E. set of 12 pieces (6mm to 05-sets 32mm) 20. Pliers combination 20 cm Pliers side cutting 15 cm Pliers round nose 15 cm Pliers flat nose 15 cm 24. Hands file 20 cm. Second cut flat Hand file 20 cm. Second cut half-round Hand file 20 cm. smooth triangular Hand file 30 cm. bastard Hand file 30 cm. round bastard File card or cleaner 21 Rate per unit Amount

2 30. Wire cutter and stripper Steel tool box with lock and key (folding type) 400x200x150 mm 15 B. Tool Instruments & general shop outfits 1. -No Outside micrometer 0 to 25 mm 2. Outside micrometer 25 to 50 mm 3. Outside micrometer 50 to 75 mm 4. Outside micrometer 75 to 100 mm 5. Internal micrometer 5 to 30 mm 6. Depth micrometer 0-25mm 7. Thread Micrometer 0-25mm 8. Drift Punch Copper 15 Cm Prick Punch 15 cm Adjustable micrometer sprit level to measure flatness, indication and taper with prismatic measuring base 11. Vernier caliper A 200 with inside and depth measurement 12. Direct reading vernier caliper B 300 (direct reading with dial) 13. Vernier depth Gauge mm 14. Vernier height gauge 500 mm

3 15. Telescope gauge 16. Dial gauge type 1 Gr. A (complete with clamping devices and stand 17. Surface gauge with dial test indicator plunger type i.e. 0. mm 18. Cylinder bore gauge capacity 20 to 160 mm 19. Compression testing gauge suitable for petrol engine. 20. Vacuum gauge to read 0 to 760 mm of Hg Tyre pressure gauge with holding 02 nipple 22. Marking Material (Consumable) 23. Marking out table 90X60X90 cm. 24. CI surface plate 400 x 400 mm with stand and cover 25. Granite surface plate 1600 x 1000 with stand and cover 26. Steel rule 15 cm inch and metric Steel rule 30 cm inch and metric Try Square 10 cm Blade Engineer s square 15 cm. Blade Calipers outside 15 cm spring Caliper inside 15 cm Spring Calipers 15 cm Hermaphrodite Dividers 15 cm Spring Scriber 15 cm Scriber with scribing black universal Chisels cross cut 200 mm X 6mm Chisel 10 cm flat Safety Goggles Hollow Punch set of seven pieces 6mm to 15mm 02-sets each 40. Ball Peen Hammer 0.75 Kg 02

4 41. Hammer copper 1 Kg with handle Hammer Mallet Hammer Plastic Hammer ball peen 0.25 kg with handle Insulated Screw driver 30 cm x 9mm 02 blade 46. Insulated Screw driver 20 cm x 9mm 02 blade 47. Electric testing screw driver Hand vice 37 mm Work bench 250 x 120 x 60 cm with 4 vices 12cm Jaw 50. Magnifying glass 75mm V Block 75 x 38 mm pair with Clamps Clamps C 100mm Clamps C 150mm Clamps C 200mm Spanner, adjustable 15cm Spark plug spanner 14mm x 18mm x 02 Size 57. Adjustable spanner (pipe wrench mm) 58. Spanner T. flocks for screwing up and up-screwing inaccessible positions 59. Spanner Clyburn 15 cm 60. Spirit level 2V 250, 05 metre Angle plate size 200x100x200mm Angle plate adjustable 250x150x Solid Parallels in pairs (Different size) 02 in Metric 64. Pliers combination 20 cm Pliers side cutting 15 cm Pliers round nose 15 cm Pliers flat nose 15 cm Vice grip pliers Circlip pliers Expanding and 02 contracting type 15cm and 20cm each 70. Grip Wrench 200mm 02

5 71. Workshop plain goggles Air impact wrench 73. Air ratchet 74. Air chisel 75. Air blow gun 76. Car Jet washer 77. Pipe flaring tool 78. Pipe cutting tool 79. Cleaning tray 45x30 cm Cleaning tray- Aluminum 45 x 30 cm Stud extractor set of 3 02-sets 82. Stud remover with socket handle 83. Rivets sets snap and dolly combined 02-each 3mm, 4mm, 6mm 84. Chemical compound for fasteners 06 (Consumable) 85. Paraffin pressure Gun Grease Gun Hacksaw frame adjustable cm Hacksaw blade (consumable) Flat File 20 cm & 35 cm bastard 04 each 90. Files assorted sizes and types including 02-sets safe edge file (20 Nos) 91. Drill Twist (assorted) (Consumables) Drill twist 1.5mm to 15mm (various 04 sizes) 0.5mm 93. Drill point angle gauge 94. Set of stock and dies - UNC, UNF and 02-sets metric 95. Taps and wrenches - UNC, UNF and 02-sets metric 96. Taps and Dies complete sets (5 types) set 97. Hand reamers adjustable 10.5 to sets mm, to mm, to mm and to mm 98. Lapping abrasives (consumable) Oil can 0.5/0.25 liter capacity Oil Stone 15 cm x 5 cm x 2.5 cm Different type gasket material

6 (consumable) 102. Different type of oil seal (consumable) 103. Sheet Metal Gauge Straight edge gauge 2 ft Straight edge gauge 4 ft Thread pitch gauge metric, BSX, BSF, MC, MF & SAE 107. Valve Lifter 108. Ladle 150mm Dia 109. Blow Lamp 1 litre Crow bar 910 x25mm Voltmeter 50V/DC Ammeter 300A/ 60A DC with external 05 shunt 113. DC Ohmmeter 0 to 300 Ohms, mid scales at 20 Ohms 114. Electric Soldering Iron 230 V 60 watts 02-each 230 V 25 watts 115. Copper bit soldering iron 0.25 Kg Thimbles of different sizes Wire Gauge (metric) Hand operated crimping tool (i) for 02 crimping up to 4mm and (ii) for crimping up to 10mm 119. Hand rubber gloves tested for 5000 V 05-pairs 120. Holders, lamp teakwood boards, plug sockets, solders, flux wires and cables batteries round consumable blocks and other consumables 121. Multimeter digital Growler 123. Scientific Calculator 124. Hydrometer Spray Gun (Painting) 500ml 126. Techometer 127. Valve Timing Diagram 128. Belt Tensioner Gauge 129. Portable electric drill Machine 130. Spring tension tester

7 131. Carburetor repair kit 132. Hot patch clamp C. General Installation/ Machineries 1. Lathe general purpose all geared height of center 150 mm to below, Gap bed between centers 1000mm with all accessories with all attachment 2. Drilling machine bench to drill up to 12mm dia along with accessories 3. Cut section working model of Single plate clutch assembly. 4. Cut section working model of Diaphragm clutch assembly. 5. Cut section working model of centrifugal clutch assembly. 6. Front axle ( Rzeeppa Joint) with stand for Dismantling and assembly 7. Rear axle with stand for Dismantling and assembly 8. Constant Mesh Gear box with stand for Dismantling and assembly. 9. Sliding mesh Gear box with stand for Dismantling and assembly. 10. Synchronous Gear box with stand for Dismantling and assembly. 11. Transfer case with stand for Dismantling and assembly. 12. Cut section model of synchronous gear box working 13. Cut section model of sliding mesh gearbox working 14. Cut section model of constant mesh gearbox working

8 15. Full floating axle and semi-floating axle assembly 16. Cut section working model of automatic transmission Gear box 17. Working model of fluid fly wheel 18. Working model of torque converter 19. Steering assembly - -each 1.Rack & pinion 2.Worm & roller 3. Recirculating ball 4.Power steering 20. Suspension and steering system trainer 21. Cut section models of shock absorbers 22. Stock absorber testing bench 23. Spring Tension scale kg. 24. Coil spring compressor for suspension spring 25. Turbo charger, variable Turbo charger -each 26. Wheel alignment gauge magnetic type with turn tables 27. Wheel alignment setup instrument 28. Tyre changer 29. Nitrogen Tyre Inflation system 30. Tube vulcanizing machine 31. Tyre vulcanizing machine 32. Camber angle gauge -set 33. Toe-in, toe-out gauge -set 34. Wheel balancing machine with accessory 35. Tubed tyre of cars 02-each 36. Tread wear indicator 37. Tyre & split rim wheel assembly 38. Solid tyre 39. Tubed tyre of car, trucks & motorcycle 40. Tubeless tyre of cars & trucks 41. Cut section of cross ply and radial tyres 42. Disk brake with caliper assembly Drum brake assembly 44. Tandem master cylinder with booster Wheel cylinder 04

9 46. Vacuum assisted hydraulics brake assembly with vacuum booster 47. Air Brake Assembly 48. Brake Lining riveting machine (foot operated) 49. Brake testing equipment (to test efficiency of vehicle where motion after braking is plotted) 50. Mechanical Hoist/Plate Form Type 51. Grinding machine (general purpose) D.E. pedestal with 300 mm dia wheels rough and smooth 52. A.C welding transformer 300 Amps 02-sets with complete accessories 53. Oxy-acetylene welding equipment with 02 complete accessories ( Low & high pressure) 54. Spot welding machine with complete accessories 55. Guillotine shearing Machine foot operation (1mt x 18G Capacity) 56. Fly press / Ball press No.4 single body 57. Pipe Bending Machine (Hydraulic type) 12mm to 30mm 58. Spring tension tester 59. Bench lever shears 250mm Blade x 3mm Capacity 60. Gas Welding Table 1220mm x760mm 61. Hydraulic Trainer Kit Basic along with accessories 62. Pneumatic Trainer Kit- Basic along with accessories 63. Electronic component trainer kit 64. Cylinder Block, CI Engine, Overhead -each camshaft & camshaft in block, air cooled 65. Carburetor Solex, Mikuny for -each dismantling and assembling 66. Carburetor repair tool kit

10 67. Demonstration board of 2W Ignition system, ignition coil 68. Demonstration board of electronic Ignition system, ignition coil 69. Spark Plug cleaning and testing equipment 70. Starter motor axial type, preengagement each type & Coaxial type 71. Distributor Duel advance type, -each reluctance type 72. Tester sparking plug NEON Type 73. Alternator assembly used for LMV Starter motor assembly used for LMV Electronic engine control module 76. Working Condition of Petrol MPFI Engine Assembly with fault simulation board 77. MPFI petrol engine with swiveling stand along with special tools for dismantling and assembling 78. Demonstration board of MPFI system 79. Ultrasonic Injection cleaning equipment 80. Fuel feed pump 81. Multi-point fuel injection pump 82. Petrol nozzle Air conditioning trainer kit 84. Air conditioning service Unit (Car) 85. Working Model of power windows 86. Petrol Engine(2-stroke) Motor Cycle/Scooter along with special tools and accessories 87. Cut model of 4 stroke Petrol engine on stand 88. Cut model of 2 stroke Petrol engine on stand 89. Mechanical Hoist/Plate Form Type 90. Multi scan tool /ECU diagnostics kit 91. Four stroke petrol engine with CNG

11 setup-working condition 92. AC alternator slip ring puller 93. Functional/experiment model of -set different type of sensors. 94. Executive Auto Electrical tool kit 95. Auto Electrical test bench 96. Cut section Model of Mock layout of a -set motor car electrical system working model 97. Car stereo 98. Battery 12V (Lead acid & Alkaline ) Battery charger 6V 24 V Electrical horn ( different types ) Wiper motor assembly Anti theft device Horn and Horn relay Air conditioned MPFI vehicle with accessories Point relays Point relays Air bag simulator 108. Driving Simulator 109. Trolley type portable air compressor single cylinder with 45 liters capacity Air tank, along with accessories & with working pressure 6.5 kg/sq cm 110. Grinding machine (general purpose) D.E. pedestal with 300 mm dia wheels rough and smooth 111. Tyer Changer Machine D. Workshop Furniture 1. Suitable Work Tables with vices Discussion Table 3. Tool Cabinet Fire Extinguishers, first- aid box -each 5. Book shelf (glass panel)

12 6. Storage Rack Storage shelf LCD projector/ LED /LCD TV (big size) 9. Multimedia CD for Automotive application 05-of different softwares 10. Desktop computer and related MS 06 office software 11. Computer Table Computer Chair 13. On Line UPS 2KVA 14. Laser Printer LIST OF TOOLS & Equipments for PLUMBER TRADE 1. Hammer Ball Peen 800 Gms File flate rough 300mm Sprit level wooden 300mm Trovel 125 IS, Wooden malt small I.S Cutting Pliers 200 I S, Steel tape(05 metre) Rule Steel 300mm both in inch and 15 MM 9. Hacksaw frame Adjustable mm 10. Chisel cold flate 20 mm Hammer ball peen 50 grams Travel C-125-is Stillson wranch 200 & 350 mm Cutting Pliers-200-IS

13 Tools, Measuring Instruments, Shop outfit and General Installation 1. Surface Plate 400x400mm grade 2. Scribing block universal 300mm File half round rough 100mm File square rough 250 mm Chisel cold flat 20x300mm Chisel cross cut 6x150mmIS, Chisel round nose 3x150mm IS, Chisel diamond point 6x150mm Punch letter set 3mm 1 set 10. Punch number set 1 set 11. Chase wedge 50mm Dresser lead 350x50mm Stick setting in 350x50mm Saw plumber 300mm Cutter, pipe wheel type 6mm to 25mm Pipe jointer lead universal LIST OF TOOLS & Equipments for PLUMBER TRADE 1. Oil stone 150mmx50mmx25mm Soldering iron, Copper fit fire heated, -each hatched,straight 500gms 3. Try square 200mm Tenon Saw 5. Hand Saw

14 6. Mortice chisel Firmer chisel Mallet medium IS Pipe opener 10. Washer cutter 11. Splash stick Sheet lead knife Chipping knife D.E. spanners set 7x8,10x11,13x7,19x22,24x27 IS: Plumber ladle Plumbers metal melting pot 10kg 17. Tool caulking set of Anvil 50 or 63 Kg, IS: Pipe bender manually operated 20. Hand drill 6mm capacity with drill set 21. Drill twist(straight shank) 3mm to -set 6mm 22. D.E Pedestal grinder with two wheels 175 rough and smooth 23. Bench drilling machine with chuk & key up to 15 mm capacity 24. Double face hammers 25. PVC welding plant 26. Gas welding Set 27. Stillson wranch 450 & 520 mm 02-sets 28. Dormat and spade -each 29. File square smooth 02-Nos 30. File Trangular rough 250mm File flat Rasp 250mm File Trangular smooth 200mm Stove melting solder 34. Googles pair welder 100mm 02-pairs 35. Flat smithy tong Ratchet Brace with drill 6 to 25mm -set 37. Snip Straight 250mm & Snip Bend 02-each LIST OF TOOLS & EQUIPMENT FOR WELDER (Gas& Electric) SHOP OUTFIT (Starting from next page)

15 1. Gas welding Goggles with Colour 13- Glasses 2. Safety boots for welders Arc welding safety Goggles Spindle Key Letter punch 6mm -set 6. Spanner double ended 6mm -32mm -set 7. Clamps 10cm & 15cm Steel Tape(05mtrs) flexible in case -set 9. Gas pressure regulator oxygen double 02 stage 10. Gas pressure regulator acetylene 02 double stage 11. First Aid Box List of Machinery for the welder trade 1. Welding Transformer with all set accessories 400,OCV ,60% duty cycle 2. Welding generator DC rotary set set 300 Amps with all accessories 3. Arc welding Rectifier set with all -set accessories(400 A),OCV V- 60% Duty cycle 4. Pedestal Grinder fitted with coarse and 02(sets) medium grain size, grinding wheel 300 mm Dia 5. Fire extinguisher foam & CO2 type 02(sets) 6. Oxygen & Acetylene cylinders -No each 7. CO2 Arc welding Machine 400A- -set Capacity with Air cooled with regulator, wire coils & Inert Gas 8. A/c, DC TIG welding machine with -set

16 water cooled Torch 300 A, with Inert Gas & all other Accessories 9. Bench Grinder fitted with fine grain -set silicon carbide, grinding wheel 150mm dia 10. Die penetrate testing kit -set 11. Arc welding table with positioners Gas welding Table with suitable gas welding fire bricks 06-sets LIST OF TOOLS & Equipments for Draughtsman Civil TRADE 1. Box drawing instruments containing 17 one 15cm compass with pin point & lengthening bar, one pair spring bows, rotating compass with interchangeable ink & pencil points, drawing pens with plain point & cross point, screw driver & box of leads.(0.2,0.3,0.4mm) 2. Weighting Triangle with tape x900cms 3. Calculator Scientific Print Trimmer Cutting edge 100cms Survey Instruments 1. Land measuring chain 30meters with 10 arrows Steel Tape 30 meters long Ranging Rod wooden fitted Optical Square PWD Pattern 04

17 5. Optical Square box type circular 6. Dumpy Level builder 25cm local length X 23mm.Complete with Box & accessories & stand Levelling Staves 4 meters reading to 5mm telescopic type 1 Telescopic 2 set piece 8. Plain Table with stand & accessories 02 sets 9. Prismatic Compass with Stand. 02 List of Equipment and Furniture for Draughtsman Civil trade 1. Chest Of Drawers (Standard) 04 No.s 2. Personal Computer, Compatibility with No. CAD (single user) with 17 colour monitor 3. CAD software (10 user licensed latest No. version) 4. Server No. 5. Printer (A3 size) No. 6. Plotter A0 (A-Zero) No. 7. UPS 0.5 KVA 05 No. 8. Computer Table 05 No 9. Operator Chair 10 No 10. Printer Table No. 11. Storage Cabnet No. 12. Book Shelf No.

18 LIST of Tools for Allied Trade used in construction Work (D.M Civil) 1. Shovel Pan M.S 25cm dia Farma wooden for measuring aggregates 4. Bucket G.I 35CM DIA O4 5. Masons s Plumb rule with Sprit level Masons Square 30x30 cms Sieve for sand 1mm/100x60 cm 8. Trowel 25cmx10cm Sieve for sand 22mm/100x60 cm 10. Measuring Tape Steel 30 meters Ladder Aluminum 3 meters Pickaxe Hammer 250gms 14. Crowbar 3cm dia.1.5 lag Hand Hammer 1kg Binoculars Latest version Surveyor s Umbrella Light Tracing Board fitted with glass and frame and lamp. 02