Installation Instructions
|
|
- Priscilla Weaver
- 5 years ago
- Views:
Transcription
1 Description The following pages show the steps required to assemble and fit the antenna mount to a vertical tower pipe of diameter 48 to 115 mm (1.9 to 4.5"). This mount provides ±20 azimuth or ±15 elevation adjustment. Notice The installation, maintenance, or removal of antenna systems requires qualified, experienced personnel. Andrew installation instructions have been written for such personnel. Antenna systems should be inspected once a year by qualified personnel to verify proper installation, maintenance, and condition of equipment. Andrew disclaims any liability or responsibility for the results of improper or unsafe installation practices.! Warning: Use protective wear to avoid skin contact with the pre-applied conductive grease on threads. Keep away from mouth. Wash thoroughly after use with liberal amounts of liquid soap and rinse with water. Do not store open near food or food sources. Dispose of empty or partially filled containers according to governmental regulations for petroleum products. Contents: oil, clay, and zinc dust. FULLY ASSEMBLED ANTENNAS 3 A Q T 1 2 I MATERIAL CHECK Unpack all materials and inspect for any shipment damage. * = Part of accessory kit. TABLE 1- ANTENNA PARTS LIST Item Qty. Description A 1 REFLECTOR ASSY D 3 U-BOLT* E 2 BRACKET* G 1 PANNING FRAME ASSY H 1 AZIMUTH ADJUSTER* I 1 ELEVATION ADJUSTER* N 11 M12x35mm HEX HEAD BOLT* 19 FLAT WASHER* 11 SPRING WASHER* 11 M12 NUT* Q 1 MOUNTING ANGLE* R 1 CLAMP ASSY* S 1 STRUT PIPE T 1 FINE ADJUSTER ANGLE BRACKET* TIGHTENING OF HARDWARE It is recommended that all hardware is tightened to the torques specified in table 2. The intergety of the mount depends on all fasteners being properly tightened. TABLE 2- FASTENER TORQUE SPECIFICATIONS Fastener Torque values in Nm (lb.ft) Material Fastener size - M5 M6 M8 M10 M12 M16 Stainless Steel (3.3) (5.7) (13.8) (28.9) (48) (18.7) Galvanized put barcode here (2.0) (3.3) H page 1 of 7 (8.1) (16.2) (28) (70.1) N G D E S R Visit our Web site at or contact your local representative for more information. is a trademark of CommScope. All trademarks identified by or are registered trademarks or trademarks, specifications or warranties relating to products or services.
2 4 MOUNT POSITION RHS/LHS the antenna may be assembled with the mounts on the right or the left side of the poles as shown. The image shown can vary from product to product. Specific views will be display showing appropriate sections page 2 of 7 Mount Assembled on Right Hand Side Mount Assembled on Left Hand Side ONLY THE LEFT SIDE ASSEMBLY IS DESCRIBED THE RIGHT SIDE ASSEMBLY IS IDENTICAL AND IS SHOWN TO THE RIGHT OF EACH IMAGE FOR REFERENCE. Visit our Web site at or contact your local representative for more information. is a trademark of CommScope. All trademarks identified by or are registered trademarks or trademarks, specifications or warranties relating to products or services.
3 5 ATTACH SAFETY BRACKET. page 3 of 7 TORQUE TO 95Nm 6 ATTACH PANNING FRAME ASSEMBLY. TORQUE TO 95Nm Visit our Web site at or contact your local representative for more information. is a trademark of CommScope. All trademarks identified by or are registered trademarks or trademarks, specifications or warranties relating to products or services.
4 7 ATTACH AZIMUTH & ELEVATION ADJUSTERS. page 4 of 7 ELEVATION ADJUSTER (ENSURE ELEVATION ADJUSTER IS ATTACHED AT TOP OF MOUNT AS SHOWN.) APPLY CONDUCTIVE GREASE TO THREADS OF ELEVATION & AZIMUTH ADJUSTERS. AZIMUTH ADJUSTER 8 ATTACH REFLECTOR ASSEMBLY. Visit our Web site at or contact your local representative for more information. is a trademark of CommScope. All trademarks identified by or are registered trademarks or trademarks, specifications or warranties relating to products or services.
5 9 ATTACH STRUT PIPE NOTE. STRUT TO LOOSELY FITTED UNTIL ALIGNMENT IS COMPLETE THEN TIGHTEN ALL FIXINGS TO TORQUE SPECIFIED. page 5 of 7 STRUT TO BE ATTACHED TO CENTRE HOLE ONLY Visit our Web site at or contact your local representative for more information. is a trademark of CommScope. All trademarks identified by or are registered trademarks or trademarks, specifications or warranties relating to products or services.
6 page 6 of 7 10 AZIMUTH & ELEVATION ENSURE THESE NUTS HAVE BEEN LOOSENED BEFORE ADJUSTING AZIMUTH (ONCE IS COMPLETE RE-TORQUE TO 95Nm) APPLY CONDUCTIVE GREASE TO THREADS OF ELEVATION & AZIMUTH ADJUSTERS. ELEVATION ±15 ENSURE THESE NUTS HAVE BEEN LOOSENED BEFORE ADJUSTING ELEVATION (ONCE IS COMPLETE RE-TORQUE TO 38Nm) ENSURE NUT IS LOOSENED BEFORE ELEVATION RE- AZIMUTH ±20 ENSURE THESE NUTS HAVE BEEN LOOSENED BEFORE ADJUSTING AZIMUTH (ONCE IS COMPLETE RE-TORQUE TO 95Nm) NOTE- LOOSEN NUTS ON STRUT PIPE BRACKET BEFORE ADJUSTING, RE- ONCE COMPLETE. ENSURE SAFETY BRACKET IS SECURELY FITTED AT ALL TIMES ENSURE NUT IS LOOSENED BEFORE ELEVATION RE- Visit our Web site at or contact your local representative for more information. is a trademark of CommScope. All trademarks identified by or are registered trademarks or trademarks, specifications or warranties relating to products or services.
7 page 7 of 7 11 ATTACH STRUT PIPE ASSY BRACKET. M16x50 TORQUE TO 95Nm APPROVED STRUCTURAL SUPPORT ENSURE BRACKETS AND NUTS ARE BOLTED RIGIDLY TOGETER AS SHOWN (VIEWED FROM TOPSIDE FOR CLARITY) BRACKETS APPROVED STRUCTURAL SUPPORT 12 STRUT PIPE POSITIONAL RANGE. LIMITS OF STRUT POSITION FOR ATTACHMENT TO APPROVED STRUCTURAL SUPPORT 15 DEPENDING ON RADIO INTEGRATION, STRUT ENVELOPE MAY BE RESTRICTED Visit our Web site at or contact your local representative for more information. is a trademark of CommScope. All trademarks identified by or are registered trademarks or trademarks, specifications or warranties relating to products or services.
Installation Instructions
put barcode here page 1 of 13 Description The following pages show the steps required to assemble and fit the antenna mount to a vertical tower pipe of diameter 48 to 115 mm (1.9 to 4.5"). This mount provides
More informationInstallation Instructions
page 1 of 9 Description The mount is designed to attach the antenna to a vertical tower pipe of diameter 115mm. The mount also provides adjustment ranges of ±15 fine elevation and ±180 ( ±12 fine) azimuth.
More informationInstallation Instructions
page 1 of 7 Description These feeds are designed for installation in shielded standard types of parabolic antennas. The feed is designed for positive metal-to-metal contact between the feed and the reflector,
More informationRevision B. Mar 2017 Side-By-Side Mounting Kit
-1 Revision B. Mar 2017 Side-By-Side Mounting Kit BSAMNT-SBS-2-2 GENERAL INFORMATION The BSAMNT-SBS-2-2 Mounting Kit allows mounting either two 350mm wide or two 457mm wide antennas with 2 mount points
More informationRevision C, June 2016 Pipe Kit for Mounting 1 to 3 Antennas 800PIPEKIT-X GENERAL INFORMATION
Revision C, June 2016 Pipe Kit for Mounting 1 to 3 Antennas 800PIPEKIT-X GENERAL INFORMATION The 800PIPEKIT-X is used for mounting one to three Commscope base station antennas to an existing pole measuring
More informationInstallation Instructions ValuLine 4ft Antennas
Rev: J Installation Instructions ValuLine 4ft Antennas 4ft (1.2m) Bulletin Version 08 page 2 of 27 Status RE Rev J Model Version 01 StatusRE Rev B This document is for the following: VHLP(X)4-*** 1.2m
More informationInstallation Instructions
Description Instructions given in this bulletin apply to either a standard, unshielded or high-performance, shielded antenna. The antenna consists of a two-piece reflector, braced by a back structure;
More information457 mm (18.0") WIDE ANTENNAS
Revision D, January 201 Side-By-Side Mounting Kit BSAMNT-SBS-2- GENERAL INFORMATION The BSAMNT-SBS-2- Mounting Kit allows mounting either two 0mm wide or two 7mm wide antennas with mount points side by
More informationInstallation Guide for HP3 & HP4 ANTENNAS
Installation Guide for HP3 & HP4 ANTENNAS with Cast Mount 495R Billerica Ave. North Billerica, MA 01862 USA Tel (978)459-8800 fax (978)459-3310 / 8814 email; sales@radiowaves.com www.radiowaves.com IMPORTANT!
More informationIMPORTANT! BEFORE UNPACKING AND ASSEMBLING THE ANTENNA MANUAL FULLY INSTRUCTIONS READ THIS INSTALLATION Rev: H
Rev: H IMPORTANT! INSTALLATION READ THIS MANUAL FULLY BEFORE UNPACKING AND ASSEMBLING THE ANTENNA Videos provide supplementary information- the instructions contained witin this bulletin must always be
More informationInstallation Instructions 6 ft Antennas Adv. Backring (with T-Mount) PA, PAL, PAD, SP, PAX, PADX, SPX DA, UA, SU, SD, SDF, DAX, UDA, UXA, SDX, SUX
Installation Instructions 6 ft Antennas Adv. Backring (with T-Mount) PA, PAL, PAD, SP, PAX, PADX, SPX DA, UA, SU, SD, SDF, DAX, UDA, UXA, SDX, SUX NMT 628-00(e) DA, UA, SU, SD, SDF DAX, UDA, UXA, SDX,
More information100A Series Low Power FM Antenna
Installation Instructions 100A Series Low Power FM Antenna Types 100A-1M, 100A-2F, 100A-2F-HW 20100326001_AEN Revision 03 Notice The installation, maintenance, or removal of antenna systems requires qualified,
More informationThese Installation Instructions are valid for antennas in the following version :
Installation Instructions 8 ft Antennas PA, PAL, PAD, PAX, PADX DA, UA, DAX, UDA, UXA HTT 81.221-15 (e) These installation instructions have been written for qualified, skilled personnel. The antenna shall
More informationThese Installation Instructions are valid for antennas in the following version :
Installation Instructions 8 ft Antennas PA, PAL, PAD, PAX, PADX DA, UA, DAX, UDA, UXA HTT 81.221-12(e) These installation instructions have been written for qualified, skilled personnel. The antenna shall
More informationThese Installation Instructions are valid for antennas in the following version :
Installation Instructions 10 ft Antennas PA, PAL, PAD, PAX, PADX DA, UA, DAX, UDA, UXA HTT 81.222-11(e) These installation instructions have been written for qualified, skilled personnel. The antenna shall
More information2005 ODU Assembly Job Aid
Summary This Job Aid covers: Verify AZ/EL Assembly Alignment Antenna Back Bracket Assembly Antenna Boom Arm Assembly Antenna TRIA Attachment Mounting the Antenna Base-Assembly Installing the Antenna Elliptical
More information2007 Shelby GT500 Long Tube Headers Installation
2007 Shelby GT500 Long Tube Headers Installation Precision manufactured using aircraft quality T-304 stainless steel; this system is designed to endure years of heavy use. Installing a Borla Performance
More informationFollowing symbols can be found next to text outlining important information.
Revision J, October 2016 641 mm Profile Panel Antennas General This instruction manual contains all necessary information required to assist in the correct installation of Panel Antennas of 641 mm (25.2
More informationUTV Universal Stronghold Auto- Latch Double Boot Mount
UTV Universal Stronghold Auto- Latch Double Boot Mount Product Instructions Part No: 0000 3 3 This Kit includes: Item Qty Part Description Bracket, Stronghold Adjustment Bracket, Bed Side Mount 3 Tube,
More informationCANVAS DOOR KIT P/N , APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Verify accessory fitment at Polaris.com.
CANVAS DOOR KIT P/N 2882902, 2882903 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain
More informationInstallation Instructions
Installation Instructions ANT, Mounting Kit, For Metrocell ANTS Mounting Kits Bulletin 6330 Revision C Dec 2015 Page 1 of GENERAL INFMATION Top of pole mounting option Fits round members 3.4" to 7.7" (6
More information3PC TONNEAU COVER INSTALLATION INSTRUCTIONS. Ford Ranger/Mazda BT-50 (without bedliner)
3PC TONNEAU COVER INSTALLATION INSTRUCTIONS Ford Ranger/Mazda BT-50 (without bedliner) Care Instructions: Clean Tonneau Cover with a mild detergent and water solution. Do not use abrasive cleaners or solvents.
More information3PC TONNEAU COVER WITH SPORTS BAR INSTALLATION INSTRUCTIONS
3PC TONNEAU COVER WITH SPORTS BAR INSTALLATION INSTRUCTIONS TC00d / Vehicle Description: NISSAN NAVARA D0 DUAL CAB 3-PIECE TONNEAU COVER PARTS LIST NO. PART NAME QTY. NO. PART NAME QTY. NO. PART NAME QTY.
More information3.5 Oval Bull Bar. Part No. B1508S/B READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION
` 3.5 Oval Bull Bar Part No. B1508S/B Fits: 2005-2014 Toyota Tacoma REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. 60-180 min Cutting Not Required Drilling Not Required support@trailfx.com READ
More information05 12 TOYOTA TACOMA 2WD
MAXTRAC SUSPENSION 4030 E LEAVERTON CT ANAHEIM, CA 92807 714 630 0363 WWW.MAXTRACSUSPENSION.COM SALES@MAXTRACSUSPENSION.COM PRODUCT: PARTS LIST K756864 6" LIFT KIT 05 12 TOYOTA TACOMA 2WD QTY SPINDLE,
More informationPRO STREET-S INSTALLATION INSTRUCTIONS
PARTS & HARDWARE LIST Part Number Description Qty Part Number Description Qty A 1534.8100 DAMPER ASSY FRONT 2 B 1534.8200 DAMPER ASSY REAR 2 C PDK4.TOOL 4mm ADJUSTMENT TOOL 1 D PDK6.TOOL 6mm ADJUSTMENT
More informationTop-of-Pole Mount for 4 Modules (TPM4) For Module Types D, E, F, & G
Module Type Width Length D 31-33 60-67 E 38-40 51-53 F 38-42 58-61 G 37-42 61-67 Top-of-Pole Mount for 4 Modules (TPM4) For Module Types D, E, F, & G ASSEMBLY INSTRUCTIONS step-by-step assembly and installation
More informationINSTALLATION INSTRUCTIONS PART NUMBER:
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-547 2003-2006 NISSAN 350Z V6-3.5L C.A.R.B. E.O. # D-670 * NOTE: Legal in California only for racing vehicles
More informationInstallation, Operation and Maintenance
Installation, Operation and Maintenance Type ES93( ) 9.3-Meter ESA Bulletin OM93 Revision D 9.3-Meter Earth Station Antenna Andrew Corporation 10500 West 153rd Street Orland Park, IL U.S.A. 60462 Telephone:
More informationTop-of-Pole Mount for 6 Modules (TPM6) For Module Type D
Top-of-Pole Mount for 6 Modules (TPM6) For Module Type D ASSEMBLY INSTRUCTIONS step-by-step assembly and installation Version 2, Rev D PCN 121712-29 Top-of-Pole Mount for 6 Modules (TPM6) For Module Type
More information2-1/4 Gallon Sprayer
2-/4 Gallon Sprayer 94008 ASSEMBLY AND OPERATING INSTRUCTIONS 349 Mission Oaks Blvd., Camarillo, CA 930 Visit our Web site at http://www.harborfreight.com Copyright 2005 by Harbor Freight Tools. All rights
More informationEffective June 2016 New Issue
Voltage Regulators MN225035EN Effective June 2016 New Issue COOPER POWER SERIES QD8 Quik-Drive Tap-Changer Switch Assembly Kit 5740785B13 and Switch Neutral Stationary Assembly Kit 5791646A48 Installation
More informationINSTALLATION INSTRUCTIONS PART NUMBER:
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 22-547 2003-2006 NISSAN 350Z V6-3.5L C.A.R.B. E.O. # D-670 * NOTE: Legal in California only for racing vehicles
More informationBMS MP40. Shock absorber Kit for BMW M3/M4 (F80/F82) - front. Mounting Instructions
Pos nr Description Part nr Qty 1 Spacer 469-15.1 Shock absorber BMS 1P40 (L) 1. Shock absorber BMS P40 (R) 1 Dust boot 1016-01 4 Spring 5 Upper spring seat 5618-10 6 Spacer Washer 469-15 8 Lock nut M1
More informationP3066 INSTALLATION MANUAL
P3066 INSTALLATION MANUAL Parts List 1 Grille guard 1 Driver / left frame bracket Level of Difficulty Moderate Scan for helpful install tips 1 Passenger / right frame bracket 1 Driver / left top bracket
More informationINSTALLATION INSTRUCTIONS Dodge Ram Crew / Mega 2500/3500 2/4WD NOTE: (tow hooks will not be re-attached) PART # P5056
INSTALLATION INSTRUCTIONS 2010-14 Dodge Ram Crew / Mega 2500/3500 2/4WD NOTE: (tow hooks will not be re-attached) PART # P5056 PARTS LIST: Qty Description Qty Description 1 Grill Guard Bar 6 12mm x 30mm
More informationHot Dog Roller Grills Instruction Manual Model #8023, Model #8024 and Model #8025 Model #8023SL, Model #8024SL and Model #8025SL
Part No. 87630 Revised November 2007 Hot Dog Roller Grills Instruction Manual Model #8023, Model #8024 and Model #8025 Model #8023SL, Model #8024SL and Model #8025SL Model #8023 shown Cincinnati, OH 45241-4807
More informationRunning Board. Part No. RBV05B. PARTS LIST: Qty Part Description Qty Part Description
` Running Board Part No. RBV05B Fits: 2014 - Current Dodge Ram Promaster 136 /159 wheel base REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. 60-180 min Cutting May be Required Drilling Required
More informationINSTALLATION INSTRUCTION PART NUMBER:
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTION PART NUMBER: 24-6003 1994-2001 ACURA Integra L4-1.8L Manual Trans. C.A.R.B. E.O. # D-670 Non VTEC models ONLY AEM bypass valves
More informationMX/MC Model Bracket. Installation Guide. Instructions for Four-, Six-, and Eight-Foot Antennas P/N JMA Wireless World Headquarters
Rev. Description EC number 01 Initial release 02 Format change 73380 MX/MC Model Bracket Instructions for Four-, Six-, and Eight-Foot Antennas P/N 81900507 JMA Wireless World Headquarters 10 7645 Henry
More informationBanks Ram-Air Intake System
Banks Ram-Air Intake System 1997-2006 Jeep 4.0L THIS MANUAL IS FOR USE WITH KITS 41816 General Installation Practices 1. For ease of installation of your Banks Ram-air intake system, familiarize yourself
More informationTop-of-Pole Mount for 6 Modules (TPM6) For Module Types A, B, & C
Top-of-Pole Mount for 6 Modules (TPM6) For Module Types A, B, & C ASSEMBLY INSTRUCTIONS step-by-step assembly and installation YOUR DISTRIBUTOR SOLIGENT 800-967-6917 www.soligent.net Version 2, Rev D PCN
More informationSpring-Engaged/Hydraulically-Released BD Caliper Brake. (i) MTY (81) QRO (442) MEX (55)
Spring-Engaged/Hydraulically-Released BD Caliper Brake (i) FORM NO. L-07-E-0300 In accordance with Nexen s established policy of constant product improvement, the specifications contained in this manual
More informationM-3000-ZX3 SVT Focus Suspension Kit INSTALLATION INSTRUCTIONS
Please contact the Tech Hot Line for the most current instruction information (586) 468-1356!!! PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION!!! INTRODUCTION: The components in
More informationInstruction Manual For The WildBlue 65cm x 75cm Elliptical Ka Antenna
Raven 2009ODU Manual Instruction Manual For The WildBlue 65cm x 75cm Elliptical Ka Antenna 1035-09-004-A Caution This instruction leaflet will assist you in the correct installation of the product. Read
More informationSafety Message to Installers and Service Personnel of Emergency Vehicle Safety Equipment
25500237 Rev. B1 0516 Safety Message to Installers and Service Personnel of Emergency Vehicle Safety Equipment Installation Instructions for the Top-Channel for IMPAXX or MicroPulse Lights on the PBX Police
More informationModel AS-RC3260 TV Cart. Rolling Cart for Audio Mount System & Flat Panel TVs
Model AS-RC3260 TV Cart Rolling Cart for Audio Mount System & Flat Panel TVs GETTING STARTED Introduction Congratulations on the purchase of your new Helios AS-RC3260 Rolling Cart. For maximum benefit,
More information4" Oval Nerf Bar. Part No. A1003S/B. PARTS LIST: Qty Part Description Qty Part Description
` 4" Oval Nerf Bar Part No. A1003S/B Fits: 2007 - Current Chevrolet Silverado 1500/2500/3500 Crew Cab 2007 - Current GMC Sierra 1500/2500/3500 Crew Cab REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT.
More informationTop-of-Pole Mount for 6 Modules (TPM6) For Module Types A, B, & C ASSEMBLY INSTRUCTIONS. step-by-step assembly and installation
Top-of-Pole Mount for 6 Modules (TPM6) For Module Types A, B, & C ASSEMBLY INSTRUCTIONS step-by-step assembly and installation Version 2, Rev D SP3311-1 PCN 121712-28 Top-of-Pole Mount for 6 Modules (TPM6)
More informationThank you for purchasing a Borla Performance Stainless Steel Header.
Thank you for purchasing a Borla Performance Stainless Steel Header. Precision manufactured using aircraft quality T-304 stainless steel; these headers are designed to endure years of heavy use. Installing
More informationVOLKSWAGEN AMAROK 3 PIECE HARD TONNEAU COVER INSTALLATION INSTRUCTIONS
VOLKSWAGEN AMAROK 3 PIECE HARD TONNEAU COVER INSTALLATION INSTRUCTIONS Care Instructions: Clean Tonneau Cover with a mild detergent and water solution. Do not use abrasive cleaners or solvents. Place these
More informationPlease take time to read and understand the following
Thank you for purchasing a Borla Performance Down Pipe. This Down Pipe has been designed for use only with a Borla Performance Cat-Back exhaust system. Replacement down-pipes are designed exclusively for
More informationInstalling the PBX04 Push Bumper on the 2015 Chevrolet Suburban/Tahoe
25500241 Rev. A0 0915 Safety Message to Installers and Service Personnel of Emergency Vehicle Safety Equipment Installing the PBX04 Push Bumper on the 2015 Chevrolet Suburban/Tahoe The lives of people
More informationCincinnati, OH USA
Part No. 87630PE Revised November 2007 Hot Dog Roller Grills Non-Stick Instruction Manual Model #8023PE, Model #8024PE and Model #8025PE Model #8023SLPE, Model #8024SLPE and Model #8025SLPE Model #8023PE
More informationInstallation, Operation and Maintenance
Installation, Operation and Maintenance Type ES45P, MP, MPJ 4.5-Meter ESA Bulletin OM45P Revision F 4.5-Meter Earth Station Antenna Andrew Corporation 10500 West 153rd Street Orland Park, IL U.S.A. 60462
More informationLong Tube Header Installation For Ford Mustang GT
Long Tube Header Installation For 2005-2008 Ford Mustang GT Precision manufactured using aircraft quality T-304 stainless steel; this system is designed to endure years of heavy use. Installing a Borla
More informationInstallation Instructions
Installation Instructions Mounting Kit, For Metro Cell Antennas Mounting Kit Bulletin 28393 201 GENERAL INFORMATION Page 1 of CommScope Infrastructure Academy offers installation training. PRE-INSTALLATION
More informationOE STYLE RUNNING BOARD FOR FORD ECOSPORT Before Installation
OE STYLE RUNNING BOARD FOR FORD ECOSPORT Before Installation Please carefully read the instructions for easy installation, which will help to prevent any damage to your vehicle. The information shown here
More informationLong Tube Header Installation For Dodge Challenger SRT-8 & R/T, Charger SRT-8 & R/T, Magnum SRT-8 & R/T & Chrysler 300 SRT-8 & 300C
Long Tube Header Installation For 2005-2008 Dodge Challenger SRT-8 & R/T, Charger SRT-8 & R/T, Magnum SRT-8 & R/T & Chrysler 300 SRT-8 & 300C Precision manufactured using high quality austenitic stainless
More information3.5" Oval Bull Bar. Part No. B1519S/B. PARTS LIST: Qty Part Description Qty Part Description
` 3.5" Oval Bull Bar Part No. B1519S/B Fits: 2017 Ford F250/350/450/550 Super Duty THE BULL BAR MAY INTERFERES WITH PARKING SENSORS, PROXIMITY SENSORS AND CRUISE CONTROL SENSORS. REMOVE CONTENTS FROM BOX.
More informationINSTALLATION INSTRUCTIONS PART NUMBER:
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 24-6004 1994-2001 ACURA Integra GSR L4-1.8L C.A.R.B. E.O. # D-670 AEM bypass valves are not compatible with this
More informationBanks Ram-Air Intake System
Banks Ram-Air Intake System 1997-2006 Jeep 4.0L THIS MANUAL IS FOR USE WITH KITS 41816 Gale Banks Engineering 546 Duggan Avenue Azusa, CA 91702 (626) 969-9600 Fax (626) 334-1743 Product Information & Sales:
More informationBy installing your Borla Performance Exhaust System, you indicate that you have read this document and you agree with the terms stated below.
Thank you for purchasing a Borla Performance Cat-back Exhaust System. Precision manufactured using aircraft quality T-304 stainless steel; this system is designed to endure years of heavy use. Installing
More informationInstallation, Operation & Maintenance Manual
IH106 Installation, Operation & Maintenance Manual ZV200 Bypass Valve Model ZV200 Bypass Valve Warning: (1) Periodic inspection and maintenance of Corken products is essential. (2) Inspection, maintenance
More informationThank you for purchasing a Borla Performance Cat-Back Exhaust System.
Thank you for purchasing a Borla Performance Cat-Back Exhaust System. Precision manufactured using aircraft quality T-304 stainless steel; this system is designed to endure years of heavy use. Installing
More informationINSTALLATION INSTRUCTIONS PART NUMBER: HONDA Civic EX L4-1.7L C.A.R.B. E.O. # D-670
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 24-6100 2001-2005 HONDA Civic EX L4-1.7L C.A.R.B. E.O. # D-670 * NOTE: Legal in California only for racing vehicles
More informationThank you for purchasing a Borla Performance Cat-Back Exhaust System.
Thank you for purchasing a Borla Performance Cat-Back Exhaust System. Precision manufactured using aircraft quality T-304 stainless steel; this system is designed to endure years of heavy use. Installing
More informationModel AS-FM64 Wall Mount. Full Motion Television Wall Mount
Model AS-FM64 Wall Mount Full Motion Television Wall Mount Getting Started Introduction Congratulations on the purchase of your new Audio Solutions AS-FM64 Television Wall Mount. For maximum benefit, please
More informationWHEEL KIT FOR 13 HP GENERATOR
WHEEL KIT FOR 13 HP GENERATOR 94192 ASSEMBLY AND OPERATING INSTRUCTIONS Due to continuing improvements, actual product may differ slightly from the product described herein. 3491 Mission Oaks Blvd., Camarillo,
More informationIMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION To reduce the risk of death, personal injury or property damage from
More information5713 / 5714 JK HEAVY DUTY GAS TANK SKID PLATE Version 1.1
SYNERGY MFG. 870 INDUSTRIAL WAY, SAN LUIS OBISPO, CA (805) 242-0397 5713 / 5714 JK HEAVY DUTY GAS TANK SKID PLATE Version 1.1 GENERAL NOTES: These instructions are also available on our website; www.synergymfg.com.
More informationTop-of-Pole Mount for 1 Module (TPM1) For Module Type H ASSEMBLY INSTRUCTIONS. step-by-step assembly and installation
Top-of-Pole Mount for 1 Module (TPM1) For Module Type H ASSEMBLY INSTRUCTIONS step-by-step assembly and installation Version 2, Rev D SP3290-2 PCN 121712-2 Top-of-Pole Mount for 1 Module (TPM1) For Module
More informationINSTALLATION INSTRUCTIONS FORD SUPER DUTY NOTE: (Vehicle Retains Tow Hook) PART # P3064
INSTALLATION INSTRUCTIONS 2011-14 FORD SUPER DUTY 250-550 NOTE: (Vehicle Retains Tow Hook) PART # P3064 PARTS LIST: Qty Description Qty Description 1 Grill Guard 2 10mm x mm Hex Bolts 1 Driver/Left Lower
More informationThank you for purchasing a Borla Performance Cat-Back Exhaust System.
Thank you for purchasing a Borla Performance Cat-Back Exhaust System. Precision manufactured using aircraft quality T-304 stainless steel; this system is designed to endure years of heavy use. Installing
More informationAKRAPOVIC CARBON-FIBER PARTS for the SUZUKI B-KING (2008)
Installation instructions: *502102* AKRAPOVIC CARBON-FIBER PARTS for the SUZUKI B-KING (2008) Congratulations on purchasing an Akrapovic carbon-fiber part. Please read these installation instructions carefully.
More informationINSTALLATION INSTRUCTIONS
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 22-544 2002-2006 NISSAN Sentra SE-R Spec-V L4-2.5L C.A.R.B. E.O. # D-670 * NOTE: Legal in California only for racing
More informationPARTS LIST: VIEWPOINT RUNNING BOARD NISSAN MURANO EXCLUDES 2dr CROSSCABRIOLET CONVERTIBLE
PARTS LIST: VIEWPOINT RUNNING BOARD Qty Description Qty Description 1 Driver/Left Running Board 14 10-1.5mm x 35mm Bolt Plates 1 Passenger/Right Running Board 6 10-1.50mm x 30mm Hex Bolt 1 Driver/Left
More informationPredator Medium Floodlight Wet Location
Predator Medium Floodlight Wet Location Installation and Maintenance Manual AFTER INSTALLATION DELIVER THIS MANUAL TO OWNER IMPORTANT SAFETY INSTRUCTIONS -READ THESE INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING
More informationCOOPER POWER SERIES. KA662R tank-lifting windlass assembly and installation instructions. Recloser Mountings MN280071EN
Recloser Mountings MN280071EN Effective May 2017 Supersedes February 1997 (S280-85-5) KA662R tank-lifting windlass assembly and installation instructions COOPER POWER SERIES DISCLAIMER OF WARRANTIES AND
More information1PC TONNEAU COVER INSTALLATION INSTRUCTIONS. Ford Ranger (with bedliner)
PC TONNEAU COVER INSTALLATION INSTRUCTIONS Ford Ranger (with bedliner) Care Instructions: Clean Tonneau Cover with a mild detergent and water solution. Do not use abrasive cleaners or solvents. Place these
More informationPREMIUM SINGLE RACK ASSEMBLY, INSTALLATION AND USE MANUAL WRITTEN BY SCOTT NOBLE NOBLE HARDWARE LLC COPYWRIGHT 2014, ALL RIGHTS RESERVED
PREMIUM SINGLE RACK ASSEMBLY, INSTALLATION AND USE MANUAL WRITTEN BY SCOTT NOBLE NOBLE HARDWARE LLC COPYWRIGHT 2014, ALL RIGHTS RESERVED INTRODUCTION THANK YOU FOR PURCHASING A SCULLING ROOF RACK FROM
More informationINSTALLATION INSTRUCTIONS PART NUMBER
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER 21-750 2013-16 Audi A4 2.0T C.A.R.B. E.O. # D-670-23 2014-16 Audi A5 2.0T C.A.R.B. E.O. # D-670-23 ITEM NO. PART
More informationThank you for purchasing a Borla Performance Cat-Back Exhaust System.
Thank you for purchasing a Borla Performance Cat-Back Exhaust System. Precision manufactured using aircraft quality T-304 stainless steel; this system is designed to endure years of heavy use. Installing
More informationRT1 SLIP-ON EXHAUST HONDA CBR600RR REV. A
08-50-43733 REV. A PARTS INCLUDED Ref. Part Number Description Qty 1) 00-200-00064 Slip-on S-bend Assembly 1 2) 00-200-00088 RT1 Aluminum Muffler Assembly 1 3) 03-46-43058 Muffler Mounting Strap 1 4) 07-27-42566
More informationThrough-Shaft Clutch-Brake LSCB-32HT, LSCB-32HT, LSCB-44, LSCB-44HT, LSCB-54HT FORM NO. L D-0606 MEX (55) QRO (442)
Through-Shaft Clutch-Brake LSCB-HT, LSCB-HT, LSCB-, LSCB-HT, LSCB-5HT In accordance with Nexen s established policy of constant product improvement, the specifications contained in this manual are subject
More informationINSTALLATION INSTRUCTIONS
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER:21-8011 1996-1999 Chevrolet C1500 V8-5.0L C.A.R.B. E.O. # D-392-19 1996-1999 Chevrolet C1500 V8-5.7L C.A.R.B. E.O.
More informationTOYOTA FJ CRUISER PERFORMANCE SHOCKS Preparation Adjustable Pole Jack
Preparation Part Number: Adjustable Pole Jack PTR13-35100/Front PTR13-35101/Rear Kit Contents: Item # Quantity Reqd. Description 1 1 Front or Rear TRD Off-Road Shock Assy (w/ Dust Cover) 2 1 Cotter Pin
More informationINSTALLATION INSTRUCTIONS
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-9024 2006-2007 CHEVROLET Silverado 2500 HD Classic V8-6.6L DSL C.A.R.B. E.O. # D-670 2006-2007 CHEVROLET Silverado
More informationHYDRAULIC SPRING COMPRESSOR SET
HYDRAULIC SPRING COMPRESSOR SET Model 47890 ASSEMBLY and OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at http://www.harborfreight.com Copyright 2002 by Harbor
More information4" Oval Nerf Bar. Part No. A1535S/B. PARTS LIST: Qty Part Description Qty Part Description
` 4" Oval Nerf Bar Part No. A1535S/B Fits: 2009-2015 Dodge Ram 1500 Reg Cab 2010-2015 Dodge Ram 2500/3500/4500/5500 Reg.Cab REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. 60-180 min Cutting Not
More informationPART NUMBER:
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-8020 2006 PONTIAC GTO V8-6.0L SEE * NOTE 2005 PONTIAC GTO V8-6.0L C.A.R.B. E.O. # D-670-2 * NOTE: Legal in California
More informationThank you for purchasing a Borla Performance Cat-Back Exhaust System.
Thank you for purchasing a Borla Performance Cat-Back Exhaust System. Precision manufactured using aircraft quality T-304 stainless steel; this system is designed to endure years of heavy use. Installing
More informationUniversal Anchoring. Serrated Double Bolt Jaw Users Manual. April 2016 by Vehicle Service Group. All rights reserved. CO9722.1
Universal Anchoring Serrated Double Bolt Jaw Users Manual April 2016 by Vehicle Service Group. All rights reserved. CO9722.1 IN20780 Rev. - 4/27/2016 CHIEF'S LIMITED ONE-YEAR WARRANTY & LIABILITY Chief
More informationCarbon Fiber Overlay for Patient Positioning for GE Healthcare Global Tables 1700, 2000, and PET/CT. Installation and Setup Manual
Carbon Fiber Overlay for Patient Positioning for GE Healthcare Global Tables 1700, 2000, and PET/CT Installation and Setup Manual DIACOR, INC. 2550 DECKER LAKE BLVD., SUITE 26, WEST VALLY CITY, UTAH 84119
More informationBMW E9x M3 Skid Plate Installation Instructions
BMW E9x M3 Skid Plate Installation Instructions Introducing the new Turner E9x M3 Skid Plate! The Turner engineering team set out to design a no-compromise belly pan replacement which requires no modification
More informationThank you for purchasing a Borla Performance Cat-Back Exhaust System.
Thank you for purchasing a Borla Performance Cat-Back Exhaust System. Precision manufactured using aircraft quality T-304 stainless steel; this system is designed to endure years of heavy use. Installing
More informationOwner s Manual. Banks Ram-Air Intake System Ford 6.8L V-10, 30-valve Class-A Motorhome. with Installation Instructions
with Installation Instructions Owner s Manual Banks Ram-Air Intake System 06-08 Ford 6.8L V-10, 30-valve Class-A Motorhome THIS MANUAL IS FOR USE WITH KIT 49191 Gale Banks Engineering 546 Duggan Avenue
More informationFord Mustang GT Long Tube Header Installation
2005-2006 Ford Mustang GT Long Tube Header Installation Precision manufactured using aircraft quality T-304 stainless steel; this system is designed to endure years of heavy use. Installing a Borla Performance
More informationOwner smanual. Banks Ram-Air Intake System Chevrolet 6.6L (LMM) Duramax Turbo-Diesel Pickups. with Installation Instructions
with Installation Instructions Owner smanual Banks Ram-Air Intake System 07-10 Chevrolet 6.6L (LMM) Duramax Turbo-Diesel Pickups THIS MANUAL IS FOR USE WITH KIT 42172 General Installation Practices 1.
More informationS Voltage Regulators PRODUCT INFORMATION GENERAL. Contents. Acceptance and Initial Inspection. Handling and Storage
Voltage Regulators QD3T350 Reversing Stationary Contact Assembly Instructions Kit 5791822A02 Service Information S225-50-43 Contents General..................................... 1 Parts Supplied...............................
More information