π H-5806 TORK AUTOMATIC TOWEL DISPENSER PARTS THE KEY AND OPTIONAL PUSH BUTTON MODE uline.com USING PUSH BUTTON MODE USING THE KEY

Transcription

1 π H-5806 TORK AUTOMATIC TOWEL ISPENSER uline.com TOOLS NEEE rill 6mm rill Bit Phillips Screwdriver PARTS ispenser x 1 ispenser Key x 1 Wall Anchor x 4 Screw x 4 Battery x 3 THE KEY AN OPTIONAL PUSH BUTTON MOE USING THE KEY 1. To open dispenser while keeping it locked, insert key at position A. (See Figure 1) Figure 1 USING PUSH BUTTON MOE 1. Insert key at position A. (See Figure 1) 2. Turn counterclockwise to position B. (See Figure 3) Figure 3 2. Turn and hold key clockwise to open dispenser. (See Figure 2) NOTE: Release key back to position A after closing to lock dispenser. 3. Remove key and push in lock to open dispenser. (See Figure 4) Figure 4 Figure 2 PAGE 1 OF 5

2 MOUNTING INSTRUCTIONS NOTE: Recommended mounting height is 48" from the floor to the bottom of the dispenser. If using template, recommended mounting height is 48" from floor to bottom of piece of paper. (See Figure 5). 1. Tape mounting template to wall at desired height and ensure that template is level. (See Figure 5) Figure 5 NOTE: Ensure that proper mounting hardware is used for appropriate wall composition, as enclosed hardware may not be compatible with your wall surface. 3. Remove template from wall. Insert wall anchors (if necessary) into four previously drilled holes. Hold dispenser up to wall so holes in wall and dispenser match up. Insert screws and ensure dispenser is level before tightening completely. (See Figure 7) Figure 7 2. Using a 6mm drill bit, drill into wall about 1½" at each marked screw location on template. (See Figure 6) Figure 6 x 3 (min.) BATTERY INSTRUCTIONS 1. While dispenser is open, locate battery compartment on bottom of dispenser. Push tab back and then lift up to open compartment. (See Figure 8) 2. Insert three batteries (included) as shown on the battery compartment cover diagram. (See Figure 9) Figure 9 Figure 8-1.5V 3 x PAGE 2 OF 5

3 HI LO HI LO LOAING INSTRUCTIONS NOTE: Paper towel roll should be inserted into the dispenser with the black core insert on the left hand side of the roll. 1. Push right roll holder arm to the right and insert black core into the left holder arm. Release left holder arm slowly to ensure that paper towel core fits properly into right holder arm. (See Figure 10) STUB ROLL FEATURE 1. If Indicator Light is flashing, the main roll is small enough in diameter to be used as a stub roll if desired. To use the low roll as a stub roll, remove the roll from the holder arms and place it on the lower set of holders located just above the battery compartment. (See Figure 13) Figure 10 Tork H1 Figure Feed paper down into the roller so the paper is in front of the roller. (See Figure 11) 2. Feed paper up over the roller and down between the roller and the front of the dispenser. Insert new full roll into main set of holder arms. (See Figure 14) Figure 11 Stub Roll Figure Locate the button on the right side of dispenser and press down until paper feeds all the way through the roller. If the roller is not catching the paper, ensure the paper is fed down in between the roller and the front of the dispenser. (See Figure 12) 3. Feed paper down into the roller as in Step 2 above. There should now be two sheets of paper down by the roller. Press the Button to feed both sheets down through the roller. ispenser will dispense two sheets until stub roll is depleted. (See Figure 15) Figure 12 Sheet Sheet Figure 15 x 2 PAGE 3 OF 5

4 OPERATION AN FEATURES INICATOR LIGHTS The Indicator Light will begin to blink yellow when the roll is thin enough in diameter to be used as a stub roll (if desired). It will continue to blink until the dispenser is loaded with a new roll. (See Figure 16) The Indicator Light will begin to blink red when the battery power is low. Replace the batteries soon if indicator light is blinking. (See Figure 16) Indicator Light Sheet Length Low Battery Tork H1 Button Sheet Length Adjustment Knob MANUAL FEE Use the Button to check for proper battery installation as well as to feed the tail of the paper into the roller. (See Figure 16) SHEET LENGTH Sheet length can be adjusted from a minimum of 8" to a maximum of 24". Turn Sheet Length Adjustment Knob clockwise for a longer sheet and counterclockwise for a shorter sheet. (See Figure 16) HAN SENSOR Figure 16 Indicator Light 5 x 3 8" (20 cm) 24" (60 cm) 8" (20 cm) 24" (60 cm) When the Switch is set to on, the user is required to wave a hand in front of the sensor to dispenser a towel. When switch is set to off, a new sheet will be dispensed automatically once a sheet is taken. (See Figure 17) On Off Figure 17 MAINTENANCE The automatic dispenser should be cleaned any time there is heavy paper dust buildup inside the dispenser. If paper dust is not a problem, approximately every year is a good frequency for cleanings. The following is recommended procedure for cleaning: 1. Open the dispenser and remove the roll of paper. 2. Clean paper dust from the inside of the dispenser. This can be done in several ways, such as vacuuming, blowing out with a can of compressed air (wear safety glasses), wiping out with a damp cloth, etc. 3. Clean the cover with a gentle cloth and water. If necessary, use an all-purpose cleaner that is safe for plastics. NOTE: It is not recommended that paper be used to clean the surface of the dispenser. Paper may scratch the high gloss surface. PAGE 4 OF 5

5 TROUBLESHOOTING OPERATING ISSUE CAUSES RECOMMENATIONS oes not function. Batteries not properly installed. oor not properly/fully closed. Paper jammed in rollers. Out of paper. Ensure batteries installed as illustrated on battery compartment cover. Make sure the cover is completely closed and the lock latched. Open cover and clear any paper jams. Look for yellow flashing light. Open cover and refill dispenser. Towel too long/short. ispenser setting is incorrect. Paper slipping between rollers. Open cover and turn sheet length knob to adjust to desired length. Open cover and make sure product turns freely, core is round and roll not too wide. ispenser is slow. Batteries low. Paper slipping between rollers. Open cover and check Light on the right side of the cassette. If flashing, replace batteries. Open cover and make sure product turns freely, core is round and roll not too wide. ispenses only one sheet. First sheet not torn off. Tear off first sheet. ispenser requires each towel to be torn off before dispensing again. Batteries draining too fast. Product too wide. Core is crushed. Battery quality. Improper installation. Open dispenser and check paper. Roll should be no wider than 7.79". Open dispenser and check the open end of the roll. Make sure it is round. Ensure all three batteries get replaced with new batteries. Use good quality batteries. Make sure all batteries are fully inserted in the correct orientation. Low battery light keeps coming on. Paper jam. Batteries nearly drained. ead battery or batteries. Open cover and clear jam. Replace all three batteries with a fresh new set of good quality batteries. Replace all three batteries with a fresh new set of good quality batteries. Cover does not close properly keeps coming open. Lock is broken. ispenser is mounted on wavy wall. Cover is warped. Replace lock. Make sure dispenser is mounted on a flat surface. Check for warped/damaged cover. Replace if necessary. Paper keeps jamming. Wrong product. Product not made correctly. Core glue not releasing. Use only Tork H1 towel refills S and S Use of any other product may result in dispenser malfunction. Make sure paper is not too wide (7.79" wide or less). Paper stuck to core at end of roll. Remove roll and load new roll. π CHICAGO ATLANTA ALLAS LOS ANGELES MINNEAPOLIS NYC/PHILA SEATTLE MEXICO CANAA PAGE 5 OF uline.com