Troubleshooting Guide: 255 LED Light

Size: px
Start display at page:

Download "Troubleshooting Guide: 255 LED Light"

Transcription

1 Troubleshooting Guide: 255 LED Light Note Use only factory replacement lights (refer to parts list for order number). Caution Carefully handle parts near membranes and wire harnesses. Allow the light to cool before removing. Carefully move the light away from the exam site to prevent contaminants from falling into the area. Warning Always disconnect power before removing covers. Failure to do so may result in personal injury. Contents Description Refer To: Troubleshooting - Troubleshooting Charts LED Lighthead Replacing the LED Light Module LED Lighthead Removal / Installation Fuse(s) Replacing the Fuse (Ceiling) Replacing the Fuses (Wall) Replacing the Fuse (Mobile) Adjustments / Repair Procedures LED Driver Board LED Driver Board Removal / Installation Power Supply Power Supply Removal / Installation Cross Tube Cross Tube Counterbalance Adjustment Cross Tube Removal / Installation Down Tube (Ceiling) Down Tube Removal / Installation Pivot Stops Pivot Stop Index Voltage Measurements - Overview Light Module Driver Board Keypad / Button Power Supply Vertical / Down Tube English [Revised: 7/7/16]

2 Quick Reference for 255 LED Light Illumination (also refer to 255 Troubleshooting Chart section): If below information does not resolve the issue, then contact technical service at MIDMARK ( ). Connect power to LED light then confirm power cord connection. Do the indicator lights flash ON and OFF? Note Take all measurements on the driver board. Light intensity will gradually dim during driver board issues and be instantly dim during lighthead issues. No Check the circuit breaker/ power source. No Check fuses. No Check wiring in vertical / down tube. Is the reading 24 VDC? No Check power supply. Reading 24 VDC (Pin 2 (-)/Pin 3 (+) on 4-Pin connector on power supply PCB)? No Replace power supply. Yes Yes Yes Press the power button. Does the LED light illuminate? No Confirm approx. 12 VDC voltage at LED light module. No Replace driver board. Check lighthead switch membrane connections. Reading 5 VDC (Pin 10 (-)/ Pin 1 (+) on membrane harness? No Replace wiring in vertical / down tube Yes Yes Replace LED light module. Check driver board. Reading 24 VDC (Pin 3 (-)/ Pin 4 (+) on J1)? No Repair wiring in cross tube/lighthead. Is the intensity dim/lower/less than expected? Yes Check lighthead. SEE NEXT PAGE Test Points Red Lead (+) Black Lead (-) Pin 3 Pin 2 Pin 4 Pin 1 Pin 5 Pin 8 Yes Confirm 12 VDC at LED light module. Yes No Replace driver board. Pin 6 Pin 7 Replace LED light module English [Revised: 7/7/16]

3 Quick Reference for 255 LED Lighthead (also refer to 255 Troubleshooting Chart section): If below information does not resolve the issue, then contact technical service at MIDMARK ( ). Note Light intensity will gradually dim during driver board issues and be instantly dim during lighthead issues. Check lighthead. Is faceplate in bad condition? No Check intensity controls. Set incorrectly? No Check LED Light module. Reading 12 VDC? No Replace LED light module. Yes Yes Replace faceplate. At highest intensity, reading is 11 VDC? Yes Replace driver board. English [Revised: mo/dd/yr]

4 Troubleshooting Chart Problem Symptom Probable Cause Check Solution Light will not illuminate. Arm assemblies can be rotated farther than specified (and/ or make noise, do not move freely, drift when released) Arm assemblies or lighthead does not rotate freely, or drifts when released. Mobile Lights only: Brake caster(s) will not lock. Light does not function when light is ON. Light does not function, or functions intermittently when lighthead or arm assemblies are moved. Cross tube (at ball pivot) can be rotated more than 580 in one direction. Mobile light cross tube can be rotated more than 540 in one direction. Lighthead can be rotated more than 180 in one direction. Ceiling Mtd Lights only: Down tube can be rotated more than 580 in one direction. Wall Mtd Lights only: Fixed arm can be rotated more than 170 (collides with wall). Cross tube rotates (at ball pivot joint) too tightly, or drifts when released. Lighthead does not rotate freely (at cross tube), or drifts when released. Ceiling Mtd Lights only: Down tube does not rotate, or drifts when released. If ceiling plate is not level, readjust as necessary. If there is excessive flexing, support ceiling structure as necessary (Refer to installation guide). Base moves when casters are set. Facility circuit breaker is tripped. Check facility circuit breaker. Reset circuit breaker. Line fuse(s) blown. Inspect fuses. Replace fuse(s). Ceiling Mounted Lights Wall Mtd. Lights Mobile Lights Fuse holder malfunctioning. Perform continuity check on fuse holder. Replace fuse holder. Switch membrane malfunctioning. Perform continuity check on switch. Replace switch membrane. Power supply malfunctioning. Check connections and voltage. If proper voltage is not present, replace power supply. Driver board malfunctioning. Check connections and voltage. If proper voltage is not present, replace driver board. LED light module malfunctioning. Check connections and voltage. If proper voltage is not present, replace LED light module. Damaged / disconnected wiring in the arm assemblies. Damaged / disconnected wiring in the arm assemblies. Perform continuity check on wiring from transformer to lighthead. Perform continuity check on wiring from transformer to lighthead. Repair / replace any damaged or disconnected wiring. (Refer to Wiring Diagrams) Repair / replace any damaged or disconnected wiring. (Refer to Wiring Diagrams) Ball pivot stop is broken. Inspect ball pivot stop. Replace ball pivot stop. Ball pivot stop is broken. Inspect ball pivot stop stop. Replace ball pivot stop. Lighthead pivot stop is broken. Inspect lighthead pivot. Replace lighthead pivot stop. Main pivot stop is broken. Inspect main pivot stop. Replace main pivot stop. Stop screw is missing / broken. Inspect fixed arm stop screw. Replace stop screw. Cross tube counterbalance out of adjustment. Lighthead tension out of adjustment. Improper installation of ceiling plate. (Plate deflecting too much, or not level) Improper installation of wall mount plate, or fixed arm not level. Base casters are worn or malfunctioning. Release tension from ball pivot joint and observe to see if the cross tube counterbalances correctly. Lighthead tension out of adjustment. Improper installation of ceiling plate. (Plate deflecting too much, or not level) Improper installation of wall mount plate, or fixed arm not level. Inspect base casters. Release tension from ball pivot joint and observe to see if the cross tube counterbalances correctly. Lighthead adjustment If ceiling plate is not level, readjust as necessary. If there is excessive flexing, support ceiling structure as necessary. (Refer to installation guide) Adjust fixed arm leveling screws as necessary (Refer to installation guide). Replace base caster(s) as necessary. English [Revised: mo/dd/yr]

5 Replacing the LED Light Module Caution Carefully handle parts near membranes and wire harnesses. Allow the light to cool before removing. Do not touch any non-black colored part of the LED light module. Carefully move the light away from the exam site to prevent contaminants from falling into the area. Warning Always disconnect power cord and allow time for light to cool before replacing. Do not touch the cone section of the LED light or reflector in light housing. LED Light Module To install light... A) Turn light OFF ( O I ). B) Turn OFF facility power breaker so there is no power in customer supplied wiring. C) Remove screws and screw caps from reflector. D) Separate front ring and faceplate from reflector. E) Disconnect LED light module connector from LED light module. F) Remove screws from LED light module. G) Peel film paper off new LED light module then install into previous place holding LED light module with a clean cloth. H) Complete steps B through F in reverse order. I) Connect power and verify operation. Reflector LED Light Module Screw * NOTE: Use only factory replacement lights (refer to parts list for order number). Sterilizable Handle Front Ring Faceplate Screw/Cap English [Revised: mo/dd/yr]

6 Lighthead Removal / Installation WARNING Disconnect power to the light before performing the following procedure. Failure to comply may result in electric shock. Step 1: Remove lighthead. A) Disconnect power to light. B) Remove screws and yoke assembly cover set. C) Remove two shoulder screws. D) Remove two pivot stops and washers. E) Separate yoke from lighthead and disconnect two wires. Shoulder Screw Note the order of all the washers and reassemble in their original positions. Correctly position pivot stops as shown into matching groove in yoke. Yoke Cover Matching Groove In Yoke Lighthead Washers *short width side Pivot Stop *long width side Screw Cover Pivot Stops Washers Shoulder Screw WARNING Mounting hardware on the lighthead must installed properly. Failure to do so may allow lighthead to fall, resulting in injury. Step 2: Install lighthead. A) Lubricate washers and shoulder screws. B) Place yoke. C) Install pivot stops, washers and shoulder screws to yoke as shown. D) Install lighthead and secure with two shoulder screws. Torque shoulder screws to 75 in-lb. E) Connect two wires. F) Install cover set. G) Install screws to cover set. H) Connect power and check for proper operation. Lighthead English [Revised: mo/dd/yr]

7 Replacing the Fuses: Ceiling Mounted Lights To replace fuses... A) Turn light OFF ( O I ). B) Turn OFF facility power breaker so there is no power in customer supplied wiring. C) Remove screws, then lower ceiling cover. D) Using a flat-bladed screwdriver, rotate fuse cap counter-clockwise 1/4 turn, while pushing upward. E) Remove fuse from fuse cap and inspect. F) Insert fuse into fuse cap. G) Using a flat-bladed screwdriver, rotate fuse cap clockwise 1/4 turn, while pushing into fuse socket. H) Install ceiling cover. I) Connect power and verify operation. Note: Inspect the fuse to determine whether it is faulty. There are two fuses on the double light and one fuse on the single light. Replacing the Fuses: Wall Mounted Lights To replace fuses... A) Turn light OFF ( O I ). B) Turn OFF facility power breaker so there is no power in customer supplied wiring. C) Remove screws, then bracket cover. D) Using a flat-bladed screwdriver, rotate fuse cap counter-clockwise 1/4 turn, while pushing upward. E) Remove fuse from fuse cap and inspect. F) Insert fuse into fuse cap. G) Using a flat-bladed screwdriver, rotate fuse cap clockwise 1/4 turn, while pushing into fuse socket. H) Install bracket cover. I) Connect power and verify operation. Note: Inspect the fuse to determine whether it is faulty. Bracket Cover Fuse Fuse Cap Fuse CRAFTSMAN Ceiling Cover CRAFTSMAN Fuse Cap MA8474i English [Revised: mo/dd/yr]

8 Replacing the Fuses: Mobile Lights Driver Board Removal / Installation: To replace fuses... A) Turn light OFF ( O I ). B) Disconnect power from light. C) Using a flat-bladed screwdriver, push in on locking tab, then pull fuse drawer out. D) Pull fuses out of fuse drawer to inspect. E) Insert fuses into fuse drawer. F) Insert fuse drawer into AC inlet (push in until you hear a clicking sound). G) Connect power and verify operation. Note: Inspect the fuse to determine whether it is faulty. Harnesses Do not damage harnesses when removing cover. Step 1: Access driver board. A) Turn light OFF and disconnect power. B) Remove cover and components from back of lighthead assembly shown. Driver Board Location Cover Fuses MA8475i Fuse Holder Lighthead Assembly English [Revised: mo/dd/yr]

9 Driver Board Removal / Installation (continued): Step 2: Remove driver board. A) Disconnect wire harnesses. B) Remove screws from cover shown. C) Carefully remove driver board off cover using a flat head screwdriver. Screw Locations Harnesses Screw Locations Step 3: Install new driver board. A) Peel off film from driver board back and align driver board before placing. B) Complete Steps 1 through 2 in reverse order. C) Connect power and verify operation. English [Revised: mo/dd/yr]

10 Power Supply Removal / Installation: Step 1: Removing existing power supply. A) Disconnect wire harnesses. B) Use needle nose pliers to release power supply. Power Supply Power Supply Base Power Supply Bottom Plate Weldment Wall Mounted Light Ceiling Mounted Light Mobile Light Wire Harnesses Power Supply Power Supply Step 2: Install new power supply. A) Secure power supply. B) Install components (reverse Step 1) as needed. C) Connect power and verify operation. English [Revised: 2/1/16]

11 Cross Tube Removal / Installation (Ceiling) Ball Pivot Sleeve WARNING Disconnect power to the light before performing the following procedure. Failure to comply may result in electric shock. The cross tube / lighthead is very heavy. To prevent injury, use an assistant for the following procedure. To remove cross tube... A) Disconnect power to light. B) Remove screw, then slide pivot sleeve up. C) While supporting cross tube / lighthead, remove two screws, then separate cross tube from down tube. D) Disconnect wire harnesses and remove cross tube. Phillips Head Screw Down Tube Cross Tube Assembly Wire Harnesses Button Head Screws WARNING Screws securing cross tube must be installed properly. Failure to do so may allow lighthead to fall, resulting in injury. To install cross tube... A) Slide ball pivot sleeve onto down tube making sure screw hole in sleeve is towards the bottom. B) With ball pivot sleeve positioned as high as possible on down tube, pull wire harness through top window of down tube. C) Align three screw holes; then insert pivot shaft of cross tube assembly into down tube. Secure cross tube assembly in position with two #10-24 x 3/8 button head screws. D) Feed wire harness through top window of down tube. E) Connect wire harnesses. Push harness into top window. F) Slide ball pivot sleeve down into position and secure with one #10-24 x 3/8 (New Units Only) phillips head screw. G) Refer to Ball Pivot Tension Adjustment if necessary. H) Slide pivot sleeve down, secure with screw. Note Male connector is power. Connectors are small size so use small probes to measure voltage. English [Revised: mo/dd/yr]

12 Cross Tube Removal / Installation (Mobile) Align three screw holes on the vertical tube with holes in ball pivot housing of the counterbalance assembly before installing any screws. Failure to comply may result in damage to screws. Install counterbalance assembly. A) Align three screw holes, then insert cross tube into vertical tube. B) Install two screws into the holes at the top of the vertical tube. C) Pull two wires from cross tube through bottom access hole. D) Connect wires from cross tube to corresponding wires from vertical tube, then push wires into tube. E) Slide sleeve into position, then secure with screw. Sleeve English [Revised: mo/dd/yr]

13 Ball Pivot Tension Adjustment / Cross Tube Counterbalance Adjustment To adjust ball pivot tension... A) Remove screw, then slide sleeve down. B) Insert screwdriver into adjustment hole. C) Move the screwdriver LEFT / RIGHT to adjust tension setting (LEFT: decreases tension / RIGHT: increases tension) D) Remove screwdriver, and check for desired tension. Repeat until desired tension is achieved. E) Slide ball pivot sleeve up, then install screw. To adjust cross tube counterbalance... A) Release tension. B) Remove cap from counterbalance. C) Loosen / tighten the adjustment screw until the cross tube balances in horizontal position. D) Install cap onto counterbalance. E) Set tension. Note: Turning the adjustment screw clockwise will lower the lighthead. Turning the adjustment screw counterclockwise will raise the lighthead. Adjustment Hole Housing Cap CRAFTSMAN Adjustment Screw Sleeve MA8517i English [Revised: mo/dd/yr]

14 Down Tube Removal / Installation (Ceiling Light) Step 1: Remove cross tube / lighthead. Refer to: Cross Tube Removal / Installation. Step 2: Remove down tube. A) Remove four screws and ceiling cover. B) Remove two screws, then separate down tube. C) Route wire harness up through down tube. WARNING Screws securing down tube must be installed properly. Failure to do so may allow lighthead to fall, resulting in injury. Step 3: To install down tube / ceiling cover... A) Install down tube, then secure with two screws. B) Position ceiling cover, then secure with four screws. Step 4: Install cross tube / lighthead. Refer to: Cross Tube Removal / Installation. English [Revised: mo/dd/yr]

15 Pivot Stop Index (Replacements / Repair / Adjustments) Stop Screw Leveling Screws Wall Tube Leveling Screws Ball Pivot Adjustment Down Tube (Ceiling) Ball Pivot Repair Yoke/Cross Tube Ball Pivot (Mobile) Ball Pivot Lighthead/Yoke English [Revised: mo/dd/yr]

16 Down Tube (Ceiling) Pivot Replacement Step 1: Remove cross tube / lighthead. Refer to: Cross Tube Removal / Installation. Step 2: Remove down tube. Refer to: Down Tube Removal / Installation. Place groove pin next to the wire harness, so wiring does not get pinched when pin is installed. Step 3: Replace main pivot stop. A) Remove groove pin. B) Remove washer, pivot housing, and pivot stop. C) Inspect two stop pins. Replace pin(s) if damaged. D) Install main pivot stop, pivot housing, and washer onto shaft. E) Install groove pin. Shaft Main Pivot Stop A Stop Pins Step 4: Install down tube. Refer to: Down Tube Removal / Installation. Step 5: Install cross tube / lighthead. Refer to: Cross Tube Removal / Installation. Washer A Groove Pin English [Revised: mo/dd/yr]

17 Ball Pivot Repair Step 1: Remove cross tube / lighthead. Refer to: Cross Tube Removal / Installation. Note the order of all the washers and reassemble in their original positions. Ball pivot must be supported when removing/installing groove pin to avoid damage to four screws. Step 2: Remove ball pivot assembly. A) Place screwdriver into adjustment hole. B) Move the screwdriver LEFT until tension is fully released. C) Carefully pull harness wires up. D) Remove groove pin using a punch tool. Adjustment Hole Washers Thrust Washer Washer (Large) Pivot Bearing (teflon side UP) Bearing Retaining Ring Washer (Large) Cam CRAFTSMAN Wave Washer Washers Step 3: Disassemble the ball pivot. A) Remove retaining ring and washers from ball pivot shaft. B) Using a punch, remove groove pin. C) Disassemble ball pivot components from shaft / housing. D) Inspect pivot bearing for excessive wear. Replace if necessary. Note: Groove pin has serrations on one end. Do not drive serrations through ball pivot shaft. Step 4: Assemble the ball pivot. A) Install pivot bearing, washers, and cam as shown. B) Install groove pin. C) Install washer, then secure with retaining ring. Groove Pin Ball Pivot Step 5: Install cross tube / lighthead. Refer to: Cross Tube Removal / Installation. Ball Pivot Brake Shaft Note Ceiling/wall shown. Wave Washer English [Revised: mo/dd/yr]

18 Ball Pivot Stop Replacement Pivot Stop Step 1: Remove the ball pivot. Refer to: Ball Pivot Repair. Stop Pin (replace if damaged) Step 2: Replace ball pivot stop. A) Remove two flange bearings from shaft. B) Disassemble shaft / housing components. C) Inspect groove pin. Replace if necessary. D) Install pivot stop (with raised portion facing UP), housing, and brake to shaft. E) Install two flange bearings to shaft. Note: Groove pin has serrations on one end. Do not drive serrations through shaft. Step 3: Assemble the ball pivot. Refer to: Ball Pivot Repair. Shaft Groove Pin Flange Bearings English [Revised: mo/dd/yr]

19 Lighthead Pivot Stop Replacement Note the order of all the washers and reassemble in their original positions. Step 1: Remove pivot stop. A) Remove screws from cover set. B) Remove cover set. C) Remove pivot stop and washers from shoulder screw. D) Remove shoulder screw from yoke. Correctly position pivot stops as shown into matching groove in yoke. Yoke Cover Set Matching Groove In Yoke Shoulder Screw Washers *short width side Pivot Stop *long width side Cover Set A Pivot Stops Washers Screws WARNING Mounting hardware must be installed properly. Failure to do so may allow lighthead to fall, resulting in injury. A Step 2: Install pivot stop. A) Install previously removed washers and shoulder screw to yoke. B) Install pivot stop to shoulder screw. Torque shoulder screw to 75 in-lb. C) Install covers. D) Install screws to cover set. Shoulder Screw Lighthead English [Revised: mo/dd/yr]

20 Yoke Pivot Replacement Step 1: Disassemble yoke. A) Remove screws from cover set. B) Remove cover set. C) Remove nut from the top of the assembly. D) Remove screw and insert from pivot bearing. E) Remove washers, shaft and pivot from yoke. F) Inspect pivot for excessive wear. Replace if necessary. G) Inspect mount on yoke. Replace if necessary. See Lighthead Pivot Stop Replacement to remove / install yoke. Note the order of all the washers and reassemble in their original positions. Washers Nut Pivot Insert WARNING Mounting hardware must be installed properly. Failure to do so may allow lighthead to fall, resulting in injury. Yoke Screw Step 2: Resassemble yoke. A) Install yoke and/or pivot (if needed). B) Lubricate washers then install washers, shaft and pivot to yoke. Ensure shaft end matches correctly in yoke hole. C) Install screw and insert to pivot. D) Install nut to the top of the pivot assembly. Torque nut to 75 in-lb. E) Install cover set. F) Install screws to cover set. Washers Mount Yoke Weldment Hole Shaft Cover Set Screws Shaft End English [Revised: mo/dd/yr]

21 Voltage Measurements Overview Driver Board Power Connector Measuring Side (For Multi-meter) 6 Warning Always disconnect power before removing covers. Failure to do so may result in personal injury. Refer to Adjustments / Repair Procedures. Ensure the PC Board does not touch the metal weldment under it. 10 Light Module Connector MA10054 Keypad/Button Connector Power Supply With Connector Removed 16 MA10053 English [Revised: 7/7/16]

22 Voltage Measurements - Light Module WARNING Insert multimeter probes carefully. To measure... A) Set light at brightest setting available B) Using multimeter, check LED lights by row on capacitors as shown. C) Measure voltage. Reading should be 12 VDC in each of the four rows. Pin to Capacitor + / - 3 C59-4 C58-5 C C C C C57-10 C56 - Ensure the PC Board does not touch the metal weldment under it. Measuring Side (For Multi-meter) Light Module Connector 10 LED Row 1 LED Row 2 LED Row 3 3 LED Row 4 English [Revised: 7/7/16]

23 Voltage Measurements - Driver Board WARNING Insert multimeter probes carefully. To measure... A) Set light at brightest setting available. B) Using multimeter, check pin 3 (-) and pin 4 (+) on connector as shown. C) Measure voltage. Reading should be 24 VDC. Ensure the PC Board does not touch the metal weldment under it. 1 Pin 3 (-) Pin 4 (+) 6 MA10056 English [Revised: 7/7/16]

24 Voltage Measurements - Keypad / Button WARNING Insert multimeter probes carefully. To measure... A) Set light at brightest setting available. B) Using multimeter, check pin 12 (-) and pin 16 (+) on connector as shown. C) Measure voltage. Reading should be 5 VDC. Ensure the PC Board does not touch the metal weldment under it. Do not let the pins touch each other. 1 Pin 12 (-) Pin 16 (+) MA10057 English [Revised: 7/7/16]

25 Voltage Measurements - Power Supply WARNING Do not touch pins or other components outside PCB protective barrier. Insert multimeter probes carefully. To measure... A) Remove connector as shown. B) Measure voltage on Pin 2 (-) and Pin 3 (+) Reading should be 24 VDC. Ensure the PC Board does not touch the metal weldment under it. Connector Pin 2 (-) Pin 3 (+) 1 4 MA10059 English [Revised: 7/7/16]

26 Voltage Measurement - Vertical / Down Tube WARNING Disconnect power to the light before performing the following procedure. Failure to comply may result in electric shock. Insert multimeter probes carefully. To measure harnes... A) Turn light OFF ( O I ) then disconnect power to light. B) Remove screw, then slide pivot sleeve up. C) Feed wire harness connectors through tube window. D) Disconnect wire harnesses. E) Connect power and turn light ON. F) Measure voltage with small sized multimeter. Reading should be 24 VDC. G) Position pivot sleeve then secure with screw. Note Male connector is power. Connectors are small size so use small probes to measure voltage. Ball Pivot Sleeve Screw Wire Harnesses Tube English [Revised: 7/7/16]

Troubleshooting Guide: 355 Lights (24V)

Troubleshooting Guide: 355 Lights (24V) Troubleshooting Guide: 355 Lights (24V) Contents Description Refer To: Troubleshooting - Troubleshooting Chart Adjustments / Repair Procedures Bulb Replacing the Bulb Fuse(s) Replacing the Fuse (Ceiling)

More information

Troubleshooting Guide: 355 Lights (12V)

Troubleshooting Guide: 355 Lights (12V) Troubleshooting Guide: 355 Lights (12V) Contents Description Refer To: Troubleshooting - Troubleshooting Chart Adjustments / Repair Procedures Bulb Replacing the Bulb Fuse(s) Replacing the Fuse (Ceiling)

More information

LED Exam Light. Service and Parts Manual. Model Numbers: FOR USE BY MIDMARK TRAINED TECHNICIANS ONLY Rev. (1/23/18)

LED Exam Light. Service and Parts Manual. Model Numbers: FOR USE BY MIDMARK TRAINED TECHNICIANS ONLY Rev. (1/23/18) LED Exam Light Model Numbers: 253 Service and Parts Manual FOR USE BY MIDMARK TRAINED TECHNICIANS ONLY 004-0779-00 Rev. (1/23/18) Table of Contents Section C Section B Section A General Info GENERAL INFORMATIOn

More information

Table of Contents. Timer Identification Timer ID BLU-U Features: 1K 6K BLU-U Features 1K 6K

Table of Contents. Timer Identification Timer ID BLU-U Features: 1K 6K BLU-U Features 1K 6K DUSA Pharmaceuticals, Inc. Table of Contents Go to Chart # Timer Identification Timer ID BLU-U Features: 1K 6K BLU-U Features 1K 6K BLU-U Features: 10K BLU-U Features 10K BLU-U Symptom Fans Running, Timer

More information

Midmark Cabinet / Wall Light Installation

Midmark Cabinet / Wall Light Installation Midmark Cabinet / Wall Light Installation [Full size template is available: 003-1289-00] warning Equipment is not suitable for use in the presence of a flammable anesthetic mixture. Equipment Alert Before

More information

Some service parts may not be available for this product!

Some service parts may not be available for this product! -00 thru -00 Power Examination Table Service and Parts Manual Serial Number Prefixes: FA, FB NO LONGER IN PRODUCTION Some service parts may not be available for this product! -00 thru -00 FOR USE BY MIDMARK

More information

Service and Parts Manual. NO LONGER IN PRODUCTION Some service parts may not be available for this product. Otolaryngology Chair.

Service and Parts Manual. NO LONGER IN PRODUCTION Some service parts may not be available for this product. Otolaryngology Chair. thru 391-001 -002 Otolaryngology Chair Serial Number Prefixes: EN, PD & V Service and Parts Manual NO LONGER IN PRODUCTION Some service parts may not be available for this product. 391-001 thru -002 NOTE:

More information

Installation Manual. 355 Lighting System MA326100

Installation Manual. 355 Lighting System MA326100 Installation Manual 355 Lighting System MA326100 Owner's Product Identification (information that you'll need to provide for servicing - key information is highlighted) Date of Purchase Serial Number(s)

More information

Maintenance Information

Maintenance Information Form 16575334 Edition 1 April 2005 Electric Screwdrivers EL, EP and ET 34V DC Series Maintenance Information Save These Instructions WARNING Maintenance procedures have the potential for severe shock hazard

More information

Service and Parts Manual

Service and Parts Manual -00 thru -00 Power Female Procedure Examination Chair Service and Parts Manual Serial Number Prefixes: BK, V, DT & FH -00 thru -00 FOR USE BY MIDMARK TRAINED TECHNICIANS ONLY SF- Part No. 00-000-00 Rev.

More information

Operation Manual. 355 Lighting System. Safety 2. Features 4. Component Overview 5. Controls & Indicators 6. Operation 7.

Operation Manual. 355 Lighting System. Safety 2. Features 4. Component Overview 5. Controls & Indicators 6. Operation 7. Operation Manual 355 Lighting System Safety 2 Features 4 Component Overview 5 Controls & Indicators 6 Operation 7 Troubleshooting 7 Operator Maintenance 8 Calling for Service 14 Specifications 15 MA326100

More information

Operation Manual. 354 / 355 Combination Lighting System MA475900

Operation Manual. 354 / 355 Combination Lighting System MA475900 Operation Manual 354 / 355 Combination Lighting System MA475900 Important! - Please Read First This manual consists of two documents: a 354 Operation Manual, and a 355 Operation Manual. Please use the

More information

Maintenance Information

Maintenance Information 45530136 Edition 1 July 2008 Electric Screwdrivers EL 24V DC Series Maintenance Information Save These Instructions WARNING Always wear eye protection when operating or performing maintenance on this tool.

More information

NO LONGER IN PRODUCTION Some service parts may not be available for this production

NO LONGER IN PRODUCTION Some service parts may not be available for this production UP TILT UP DOWN BACK UP TILT DOWN UP BACK DOWN DOWN -0 thru -0 Service and Parts Manual Power Examination Table Serial Number Prefixes: GT, GV, HY, JX, JY & LS NO LONGER IN PRODUCTION Some service parts

More information

354 Mobile Lighting System

354 Mobile Lighting System Important Information Page 2 Installation and Operation Manual 354 Mobile Lighting System Installation Page 3 Description Page 12 Components Overview Page 13 Controls & Indicators Page 14 Operation Page

More information

P-600. Technical Manual. Troubleshooting Repairs Replacements

P-600. Technical Manual. Troubleshooting Repairs Replacements P-600 Technical Manual Troubleshooting Repairs Replacements Table of Contents P-600 Lift Symptoms and Problems Finding the Problem Before Getting Inside 3 Pneumatic Systems 4 Electrical Systems 5 Mechanical

More information

VHM-P (Non-Locking) and VHM-PL (Locking) Variable Height Arm with Slide-In Mounting Plate

VHM-P (Non-Locking) and VHM-PL (Locking) Variable Height Arm with Slide-In Mounting Plate 3875 Cypress Drive Petaluma, CA 94954 800.228.2555 +1.707.773.1100 Fax 707.773.1180 www.gcx.com VHM-P (Non-Locking) and VHM-PL (Locking) Variable Height Arm with Slide-In Mounting Plate (Refer to qualified

More information

TECUMSEH/PEERLESS LTH Model Transaxle Supplement

TECUMSEH/PEERLESS LTH Model Transaxle Supplement TECUMSEH/PEERLESS LTH Model Transaxle Supplement This supplemental repair manual has been created to provide service information for the LTH model transaxle. This information will be incorporated into

More information

3875 Cypress Drive Petaluma, CA Fax

3875 Cypress Drive Petaluma, CA Fax 3875 Cypress Drive Petaluma, CA 94954 800.228.2555 +1.707.773.1100 Fax 707.773.1180 www.gcx.com VHM-P (Non-Locking) Variable Height Arm with Fixed Angle Front End for Flat Panel / Keyboard Bracket (L Brackets

More information

Midmark Light Install: L/R mounted on Ultra Chair

Midmark Light Install: L/R mounted on Ultra Chair Midmark Install: L/R mounted on Ultra Chair warning Equipment is not suitable for use in the presence of a flammable anesthetic mixture. Applies to Models: 153914 (-002) 153915 (-002) Language of origin:

More information

VHM-P (Non-Locking) Variable Height Arm with VESA Mounting Plate for 75 x 75mm or 100 x 100mm applications

VHM-P (Non-Locking) Variable Height Arm with VESA Mounting Plate for 75 x 75mm or 100 x 100mm applications 3875 Cypress Drive Petaluma, CA 94954 800.228.2555 +1.707.773.1100 Fax 707.773.1180 www.gcx.com VHM-P (Non-Locking) Variable Height Arm with VESA Mounting Plate for 75 x 75mm or 100 x 100mm applications

More information

Installation Manual. 354 / 355 Combination Lighting System MA475900

Installation Manual. 354 / 355 Combination Lighting System MA475900 Installation Manual 354 / 355 Combination Lighting System MA475900 Important! - Please Read First This document is broken down into three parts: This page, which provides additional information for installing

More information

Installation Instructions COMPETITION/PLUS SHIFTER Ford Mustang MT82 6-Speed Manual Transmission Catalog#

Installation Instructions COMPETITION/PLUS SHIFTER Ford Mustang MT82 6-Speed Manual Transmission Catalog# Installation Instructions COMPETITION/PLUS SHIFTER 2015-2017 Ford Mustang MT82 6-Speed Manual Transmission Catalog# 3916037 Rev. 00 WORK SAFELY! For maximum safety, perform this installation on a clean,

More information

Installation Manual. 355 Lighting System

Installation Manual. 355 Lighting System Installation Manual 355 Lighting System Owner's Product Identification (information that you'll need to provide for servicing - key information is highlighted) Date of Purchase Serial Number(s) - Dual

More information

GENUINE FOG LIGHT INSTALLATION AND USER S INSTRUCTIONS

GENUINE FOG LIGHT INSTALLATION AND USER S INSTRUCTIONS GENUINE FOG LIGHT INSTALLATION AND USER S INSTRUCTIONS Thank you for purchasing a genuine Mazda accessory. Before removal and installation, be sure to thoroughly read these instructions. Please read the

More information

FE 35, 40, 55, EC Every time you open the housing, clean the motor with a soft brush.

FE 35, 40, 55, EC Every time you open the housing, clean the motor with a soft brush. FE 35, 40, 55, EC 70 1 Service Manual FE 35, FE 40, FE 55 Electric Trimmers, EC 70 Electric Edger As the design concept of the FE 35 and FE 40 trimmers is almost identical, the descriptions and servicing

More information

Safe-T-element Installation Instructions

Safe-T-element Installation Instructions Safe-T-element Installation Instructions For: PTI STEZA (2x2 Burner Configuration) & PTI STEZB (3x1 Burner Configuration) Revision K (May. 3 2012) TABLE OF CONTENTS 1. PREPARATION... 3 1.1 General Safety

More information

TOYOTA TUNDRA TVIP V4 Preparation

TOYOTA TUNDRA TVIP V4 Preparation Preparation Part Number: PT398-00100 PT398-00100-AA Conflicts Do not install into vehicles without RKE system. Recommended Sequence of Application Item # Accessory 1 TVIP/RES Any TVIP or RES system 2 XM

More information

BOLT-ON AND WELD-ON FLUSH FLOOR SLIDEOUT SYSTEMS OPERATION AND SERVICE MANUAL

BOLT-ON AND WELD-ON FLUSH FLOOR SLIDEOUT SYSTEMS OPERATION AND SERVICE MANUAL BOLT-ON AND WELD-ON FLUSH FLOOR SLIDEOUT SYSTEMS OPERATION AND SERVICE MANUAL TABLE OF CONTENTS SYSTEM...... Warning........ Description...... Prior to Operation OPERATION... Main Components... Mechanical...

More information

Maintenance Information

Maintenance Information 16575219 Edition 4 October 2013 Air Screwdrivers QP1P, QP1S and QP1T Series Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings,

More information

Section 7 - Troubleshooting Guide

Section 7 - Troubleshooting Guide Section 7 - Troubleshooting Guide Section 7 - Troubleshooting Guide IMPORTANT While this troubleshooting guide provides information to aid in troubleshooting problems with the range, it does not contain

More information

3M Overhaul Service Kit

3M Overhaul Service Kit SERVICE INSTRUCTIONS FOR 3M 12,000 RPM 3 in. (77 mm) RANDOM ORBITAL SANDERS 3M Overhaul Service Kit The part number 20346, 3M Overhaul Service Kit, contains all the replacement parts that naturally wear

More information

* * APPLICABLE MODELS: 2014 > Mazda 3

* * APPLICABLE MODELS: 2014 > Mazda 3 PART NUMBER: 0000 8C L48 (DIO) / 0000 89 L84 (PIO) GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS Rev. AAA *550-0700-000* APPLICABLE MODELS: 2014 > Mazda 3 REQUIRED COMPONENTS: ITEM QTY DESCRIPTION Usage

More information

Sofa Slideout Assembly OWNER'S MANUAL. Rev: Page 1 Sofa Slideout Owners Manual

Sofa Slideout Assembly OWNER'S MANUAL. Rev: Page 1 Sofa Slideout Owners Manual Sofa Slideout Assembly OWNER'S MANUAL Rev: 06.14.2016 Page 1 Sofa Slideout Owners Manual TABLE OF CONTENTS Warning, Safety, and System Requirement Information 3 Product Information 3 Prior to Operation

More information

UOW Series Repair Manual UOW-11 & UOW-T60 Series

UOW Series Repair Manual UOW-11 & UOW-T60 Series UOW Series Repair Manual UOW-11 & UOW-T60 Series 100000 SE Pine St., Portland, OR 97216 800-852-1368 503-254-6600 www.aimco-global.com Contents Page 1. Tools Needed for Repair 2 2. Disassembly and Reassembly

More information

630 (-010 thru -013, -020 thru -023)

630 (-010 thru -013, -020 thru -023) 60 (-00 thru -0, -00 thru -0) Headrests Actuators: Back Tilt Foot Upholstery: Premium UltraPremium Controls: Corded Hand Ctrl Corded Foot Ctrl Wireless Fuses Product Overview Headlock Components Seat Section

More information

VECTRIX VX-2 SERVICE MANUAL. Version 1.0/May 2011 VECTRIX, LLC

VECTRIX VX-2 SERVICE MANUAL.   Version 1.0/May 2011 VECTRIX, LLC www.vectrix.com CONTENTS SECTION A: Tools 1 Tools Needed SECTION B: Mechanical Parts 1 Front Fairing 2 Front Console Cover 3 Speedometer Cover 4 Front Vertical Panel Cover-Lower 5 Front Vertical Panel

More information

Embedded Rack Slide-out System

Embedded Rack Slide-out System Embedded Rack Slide-out System SERVICE MANUAL Rev: 02.16.2017 Page 1 Electric Embedded Rack Slide-out System TABLE OF CONTENTS Safety Information 3 Product Information 3 Operation 4 Extending Slide-Out

More information

255 LED Light Dual Conversion Installation [9A584001]

255 LED Light Dual Conversion Installation [9A584001] 255 LED Light Dual Conversion Installation [9A584001] Note Two single ceiling lights are needed. The ceiling must be capable of supporting the double light system. Weight (max.): 118 lb (53.6 kg); Torque

More information

ANDCO Eagle Actuator Instruction Manual

ANDCO Eagle Actuator Instruction Manual ANDCO Actuators ANDCO Eagle Actuator Instruction Manual The information contained in this manual is essential to safe, successful, long term operation of your Andco Eagle Linear Actuator. Read and follow

More information

Installation Manual 354 / 355 Combination Lighting System

Installation Manual 354 / 355 Combination Lighting System Installation Manual 354 / 355 Combination Lighting System MA551601 180 Height of Lighthead Assembly Adjustable from 50.0 in. (127.0 cm) to 74.0 in. (188 cm) above floor Based on 8' units with 8' Ceiling

More information

NOTE: Visit our website at for video repair procedures, under the Tools section.

NOTE: Visit our website at   for video repair procedures, under the Tools section. Repair Instructions Hypro Repair Tools: Tool Box No. 3010-0168 1/4" Allen Wrench No. 3020-0008 Support Bars (2) No. 3010-0064 Port Brush No. 3010-0066 1/16" Allen Wrench No. 3020-0009 Brush Holder No.

More information

Auger System - Troubleshooting Guide

Auger System - Troubleshooting Guide Haas Technical Documentation Auger System - Troubleshooting Guide Scan code to get the latest version of this document Translation Available 1. Multi Auger 2. Single Auger Electrical Diagram Copyright

More information

SX1000 Service Manual SALES: CUSTOMER SERVICE:

SX1000 Service Manual SALES: CUSTOMER SERVICE: SX1000 Service Manual SALES: 800-278-3933 CUSTOMER SERVICE: 800-745-1373 Revision: August 1999 Table of Contents Section Page I. Overview 2 II. Troubleshooting Tables 3 III. Maintenance Procedures Procedure

More information

LEXUS RC 350/RC-F ILLUMINATED DOOR SILLS Preparation

LEXUS RC 350/RC-F ILLUMINATED DOOR SILLS Preparation Preparation Part Number: PT944-24150 Kit Contents Item # Quantity Reqd. Description 1 2 Inner LED Scuff 2 2 Outer Scuff 3 1 Hardware Bag Hardware Bag Contents Item # Quantity Reqd. Description 1 15 20

More information

Dental Chair Midmark UltraComfort & UltraTrim Dental Chair

Dental Chair Midmark UltraComfort & UltraTrim Dental Chair Dental Chair Midmark UltraComfort & UltraTrim Dental Chair Service and Parts Manual Serial Number Prefixes: NT, NZ & V Dental Chair (UltraComfort shown) FOR USE BY MIDMARK TRAINED TECHNICIANS ONLY SF-1620

More information

Loose Components. VetPro 5000 Wall / Cabinet Mount Installation. Applies to Models:

Loose Components. VetPro 5000 Wall / Cabinet Mount Installation. Applies to Models: VetPro 5000 Wall / Cabinet Mount Installation warning Equipment not suitable for use in the presence of a flammable anesthetic mixture. Applies to Models: 8001-001 8001-002 8001-005 8001-006 Loose Components

More information

491 Harness Installation Kit

491 Harness Installation Kit 491 Harness Kit 002-0759-00 Kit Components: Qty Harness Assy... 1 Wire Clip... 2 Wire Tie (7 1/2 )... 5 Wire Tie (7 1/4 )... 4 Instruction... 1 Remove Back Cover Warning Disconnect Power before removing

More information

Model 2300JL Installation Guide

Model 2300JL Installation Guide Model 2300JL Installation Guide POWER ACCESS CORPORATION 4 HERSHEY DRIVE, DOCK 4 ANSONIA, CT 06401 800-344-0088 WEBSITE: www.power-access.com EMAIL: salesinfo@power-access.com 1 STANDARD PARTS MODEL 2300JL

More information

Midmark Dental Lightheads

Midmark Dental Lightheads Midmark Dental Lightheads Halogen Lighthead (short neck) LED Lightheads Halogen Lighthead (long neck) Index: Halogen / LED 004-0815-00 [Revised: 11/5/12] Pictorial Index: Halogen Lightheads (short neck)

More information

INSTALLATION INSTRUCTIONS FOR DSP9600/9100 WHEEL BALANCER

INSTALLATION INSTRUCTIONS FOR DSP9600/9100 WHEEL BALANCER Form 5063T, 06-05 Supersedes Form 5063T, 02-04 INSTALLATION INSTRUCTIONS FOR DSP9600/9100 WHEEL BALANCER This document provides the information needed to install the DSP9600/9100 Wheel Balancer. NOTE:

More information

Model 2300DL Installation Guide

Model 2300DL Installation Guide Model 2300DL Installation Guide POWER ACCESS CORPORATION 4 HERSHEY DRIVE, DOCK 4 ANSONIA, CT 06401 800-344-0088 WEBSITE: www.power-access.com EMAIL: salesinfo@power-access.com 1 STANDARD PARTS MODEL 2300DL

More information

* * APPLICABLE MODELS: 2014 > Mazda 6

* * APPLICABLE MODELS: 2014 > Mazda 6 PART NUMBER: 0000 8C H02(DIO) / 0000 89 H18(PIO) GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS Rev. AAA *550-0694-000* APPLICABLE MODELS: 2014 > Mazda 6 REQUIRED COMPONENTS: ITEM QTY DESCRIPTION Usage

More information

REAR AXLE <FWD> GROUP 27A 27A-1 CONTENTS GENERAL INFORMATION... 27A-2 SPECIAL TOOLS... 27A-4 ON-VEHICLE SERVICE... 27A-5 SPECIFICATIONS...

REAR AXLE <FWD> GROUP 27A 27A-1 CONTENTS GENERAL INFORMATION... 27A-2 SPECIAL TOOLS... 27A-4 ON-VEHICLE SERVICE... 27A-5 SPECIFICATIONS... 27A-1 GROUP 27A CONTENTS GENERAL INFORMATION........ 27A-2 SPECIFICATIONS............... 27A-2 SERVICE SPECIFICATIONS........... 27A-2 REAR AXLE DIAGNOSIS......... 27A-3 INTRODUCTION TO REAR AXLE DIAGNOSIS........................

More information

GEARBOX AND 4X4 COUPLING UNIT SERVICE TOOLS SERVICE TOOLS OTHER SUPPLIER SERVICE PRODUCTS

GEARBOX AND 4X4 COUPLING UNIT SERVICE TOOLS SERVICE TOOLS OTHER SUPPLIER SERVICE PRODUCTS GEARBOX AND 4X4 COUPLING UNIT SERVICE TOOLS Description Part Number Page BLIND HOLE BEARING PULLER SET... 529 036 117... 199 COUNTERSHAFT OIL SEAL PUSHER... 529 036 222... 192 ECM ADAPTER TOOL... 529 036

More information

* * APPLICABLE MODELS: 2017 > CX-5

* * APPLICABLE MODELS: 2017 > CX-5 PART NUMBER: 0000 8C R06(DIO) / 0000 89 R28(PIO) GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS Rev. AAA *550-0681-000* APPLICABLE MODELS: 2017 > CX-5 REQUIRED COMPONENTS: ITEM QTY DESCRIPTION Usage Chart

More information

CHAINGUARD REGAL ST COLOR

CHAINGUARD REGAL ST COLOR DESOTO/ REGAL HAULER PARTS LIST Item Part # Description QTY Item Part # Description QTY 1 11871 REFLECTOR KIT TRIKE 1 32 11764 FENDER BRACE 24" MWT 1 2 12199 SCREW #14 x 3/4 4 33 12176 NUT5/16-24 HEX 2

More information

ISO1000R Service Manual SALES: CUSTOMER SERVICE:

ISO1000R Service Manual SALES: CUSTOMER SERVICE: ISO1000R Service Manual SALES: 800-278-3933 CUSTOMER SERVICE: 800-745-1373 Revision: August 1999 Table of Contents Section Page I. Overview 2 II. Troubleshooting Tables 3 III. Maintenance Procedures Procedure

More information

LAMPS 8L - 1 LAMPS CONTENTS

LAMPS 8L - 1 LAMPS CONTENTS TJ LAMPS 8L - 1 LAMPS CONTENTS BULB APPLICATION... 16 HEADLAMP ALIGNMENT... 5 LAMP BULB SERVICE... 8 LAMP DIAGNOSIS... 1 LAMP SERVICE... 11 LAMP SYSTEMS... 15 LAMP DIAGNOSIS INDEX GENERAL INFORMATION GENERAL

More information

(Refer to qualified personnel)

(Refer to qualified personnel) 3875 Cypress Drive Petaluma, CA 94954 800.228.2555 +1.707.773.1100 Fax 707.773.1180 www.gcx.com Installation Guide VHM-P (Non-Locking) and VHM-PL (Locking) Variable Height Arm (Slide-Above-Arm Configuration)

More information

OPERATION AND MAINTENANCE MANUAL

OPERATION AND MAINTENANCE MANUAL WREN IBT SERIES HYDRAULIC TORQUE WRENCHES IBT SQUARE DRIVE SERIES OPERATION AND MAINTENANCE MANUAL FOR WREN Products: POINT 75, 1IBT, 3IBT, 5IBT, 8IBT, 10IBT, 20IBT, 25IBT, 35IBT, 50IBT SQUARE DRIVE HYDRAULIC

More information

GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS. ITEM QTY DESCRIPTION Usage Chart Service Part Number. 1 1 Mirror Assembly w/ Compass 1

GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS. ITEM QTY DESCRIPTION Usage Chart Service Part Number. 1 1 Mirror Assembly w/ Compass 1 AUTO PART NUMBER: 0000 8C P4 (DIO)/ 0000 89 P25 (PIO) REQUIRED COMPONENTS: INSTALLATION KIT: 2 SA Harness - 2 Conductor 3 0 Wire Ties 4 Wire Cover 5 A-Pillar Tether Clip (D09W-6862) 6 3 Foam Tape 7 3 Electro-Tap(wire

More information

Cylinder and Valve: AirHawk II Air Mask

Cylinder and Valve: AirHawk II Air Mask Cylinder and Valve: AirHawk II Air Mask MAINTENANCE AND REPAIR MSA 011 (L) Rev. 0 MSA 2010 Prnt. Spec. 10000005389(I) Mat. 10104218 Doc. 10104218 Parts List Cylinder Replacement Kits Item P/N Description

More information

CHAINGUARD REGAL ST COLOR

CHAINGUARD REGAL ST COLOR DESOTO/ REGAL HAULER PARTS LIST Item Part # Description QTY Item Part # Description QTY 1 11871 REFLECTOR KIT TRIKE 1 32 11762 FENDER BRACE 20" MWT 1 2 12199 SCREW #14 x 3/4 4 11764 FENDER BRACE 24" MWT

More information

Maintenance Information

Maintenance Information 16572679 Edition 2 May 2014 Air Drill QP Series Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings, and to avoid these potentially

More information

Z TECHNICAL INSTRUCTIONS

Z TECHNICAL INSTRUCTIONS ÍNDICE: Z40 2.0 TECHNICAL INSTRUCTIONS 1.- Error list 2.- Replace the control board 3.- Opening the machine 4.- Replace the power board 5.- Dismantling motor and gear box 6.- Assembly of gear box 7.- Pushing

More information

Midmark Track Light Installation

Midmark Track Light Installation Midmark Track Light Installation [Full size ceiling template is available: 003-1287-00] Applies to Models: 153910 (-002) 153656 (-001) Language of origin: English Physical Requirements warning Equipment

More information

If technical support is required, please contact Advent Technical Support at

If technical support is required, please contact Advent Technical Support at Document 128-9015A Created 12/12/11 Kit Contents: Item # Qty. Component Description 1 2 Headrest Assembly 2 2 Cables # 3 3 1 Power Cord # 9 4 1 FM Antenna 5 1 Control Box 6 2 IR Headphones 7 2 Remote Control

More information

The POWER. In PRESENTATION PRODUCTS. Instruction Book for COSMOPOLITAN ELECTROL For Sizes Up To 9'x12' DA-LITE SCREEN COMPANY, INC.

The POWER. In PRESENTATION PRODUCTS. Instruction Book for COSMOPOLITAN ELECTROL For Sizes Up To 9'x12' DA-LITE SCREEN COMPANY, INC. The POWER In PRESENTATION PRODUCTS Instruction Book for COSMOPOLITAN ELECTROL For Sizes Up To 9'x12' DA-LITE SCREEN COMPANY, INC. 3100 North Detroit Street Post Office Box 137 Warsaw, Indiana 46581-0137

More information

Body Electrical System

Body Electrical System Body Electrical System GENERAL....BE -2 MULTI FUNCTION SWITCH...BE -8 HORN...BE -11 FUSES AND RELAYS...BE -12 INDICATORS AND GAUGES...BE -19 LIGHTING SYSTEM...BE -24 DAYTIME RUNNING LIGHTS...BE -30 BE-2

More information

Maintenance Information

Maintenance Information 80234313 Edition 1 June 2006 Air Grinder, Die Grinder, Sander and Belt Sander Series G1 (Angle) Maintenance Information Save These Instructions WARNING Always wear eye protection when operating or performing

More information

Wall / Casework Mounted Delivery Systems (Procenter)

Wall / Casework Mounted Delivery Systems (Procenter) 20 20 0 0 40 40 2 3 0 4 60 60 5 6 7 80 80 00 00 2 3 4 Wall / Casework Mounted Delivery Systems (Procenter) Common Components...004-0859-99 2:00 / FTC Delivery Systems Side Delivery Systems... 004-0886-99

More information

Installation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3

Installation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3 Page 1 Installation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3 Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage

More information

TABLE OF CONTENTS. Ram Assembly

TABLE OF CONTENTS. Ram Assembly TABLE OF CONTENTS DUC Cover------------------------------------------------------------------------------------ 00 Table of Contents----------------------------------------------------------------------------

More information

NIGHT-LITE PRO II. Electrical System Troubleshooting Guide and Procedures

NIGHT-LITE PRO II. Electrical System Troubleshooting Guide and Procedures NIGHT-LITE PRO II Electrical System Troubleshooting Guide and Procedures Allmand Bros. Inc. PO Box 888 1502 W. 4 th Ave. Holdrege NE 68949 USA 308-995-4495 Phone 800-562-1373 Toll-Free www.allmand.com

More information

Service Manual. LT-5 Lawn Tractor

Service Manual. LT-5 Lawn Tractor Service Manual LT-5 Lawn Tractor NOTE: These materials are for use by trained technicians who are experienced in the service and repair of outdoor power equipment of the kind described in this publication,

More information

3M Overhaul Service Kit

3M Overhaul Service Kit SERVICE INSTRUCTIONS FOR 3M 12,000 RPM 5 in. (127 mm) and 6 in. (150 mm) RANDOM ORBITAL SANDERS 3M Overhaul Service Kit The part number 20347, 3M Overhaul Service Kit, contains all the replacement parts

More information

CHAPTER 14 PARKING BRAKE

CHAPTER 14 PARKING BRAKE 1 page INDEX1 PARKING BRAKE 14-1 14-143E-05 CHAPTER 14 PARKING BRAKE 1Models FA and FB with LF05S TROUBLESHOOTING...14-2 SPECIAL TOOLS...14-3 INSPECTION AND ADJUSTMENT...14-4 PARKING BRAKE...14-7 14 PARKING

More information

TOYOTA TACOMA EC REARVIEW MIRROR Preparation

TOYOTA TACOMA EC REARVIEW MIRROR Preparation Preparation Part Number: PT374-35052 Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description 1 1 T-tap Connectors,

More information

CAUTION CAUTION CAUTION

CAUTION CAUTION CAUTION 7. Inspect the brass commutator end of the armature for any discolored spots or damage. If the commutator is slightly discolored or damaged, the armature must be replaced. This is a molded commutator and

More information

MAINTENANCE MANUAL DI 16

MAINTENANCE MANUAL DI 16 MAINTENANCE MANUAL DI 16 0.2-1.6% Press Ctrl + L for full screen 1 STANDARD INSTALLATION Inlet Outlet Optional accessories: Pressure regulator Solenoid valves Water meter Flow restrictor 200 Mesh/ 80 micron

More information

Solstice Electric Fryers SE Series Service Manual

Solstice Electric Fryers SE Series Service Manual Solstice Electric Fryers SE Series Service Manual L22-330 R1 (10/12) Notice In the event of problems or questions about your order, contact the Pitco Frialator factory at (603) 225-6684. In the event of

More information

Quickie S-11 Service Manual

Quickie S-11 Service Manual Quickie S-11 Service Manual 05 Sunrise Medical Inc. 100740 Rev A Quickie S-11 Troubleshooting Guide INTRODUCTION... 0.1 Specifications VSI Controller... 0.2 Plugs/Connectors... 0.3 Main Wiring Diagram/

More information

UAN Series Pneumatic Nutrunner Repair Manual

UAN Series Pneumatic Nutrunner Repair Manual UAN Series Pneumatic Nutrunner Repair Manual PO Box 16460, Portland, OR 97292-0460 503-254-6600 Fax 503-255-2615 www.aimco-global.com Contents Page 1. Tools Needed for Repair of UAN Series Pneumatic Nutrunner

More information

Marsh Shipping Supply Co. LLC. Marsh TD2100 Electric Taper Technical Manual

Marsh Shipping Supply Co. LLC. Marsh TD2100 Electric Taper Technical Manual Marsh Shipping Supply Co. LLC Marsh TD2100 Electric Taper Technical Manual 2 A wall-socket must be close to the product and readily accessible. The overall system is protected against overload by the branch

More information

TS93 EMF T/PT/TDE. Surface applied door closer

TS93 EMF T/PT/TDE. Surface applied door closer TS9 EMF T/PT/TDE Surface applied door closer Installation instructions: Pull side track mount door closer (no smoke detector) (EMF T) Push side track mount closer (no smoke detector) (EMF PT) Double egress

More information

* * APPLICABLE MODELS: 2016 > CX-3

* * APPLICABLE MODELS: 2016 > CX-3 PART NUMBER: 0000 8C S01(DIO) / 0000 89 S07(PIO) GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS Rev. AAA *550-0688-000* APPLICABLE MODELS: 2016 > CX-3 REQUIRED COMPONENTS: ITEM QTY DESCRIPTION Usage Chart

More information

Heavy Duty Miniature Quick-Change Applicator (End-Feed Type) with Mechanical or Air-Feed Systems

Heavy Duty Miniature Quick-Change Applicator (End-Feed Type) with Mechanical or Air-Feed Systems Heavy Duty Miniature Quick-Change Applicator (End-Feed Type) with Mechanical or Air-Feed Systems Instruction Sheet 408-8039 02 JUN 16 Rev G Ram Post Wire Disc Insulation Disc Insulation Crimper Stripper

More information

OLYMPIAN MODEL 740 Operation and Service Manual

OLYMPIAN MODEL 740 Operation and Service Manual OLYMPIAN MODEL 740 Operation and Service Manual P/N 133911-102 FCI MANUAL P/N 133865-001 Data herein has been verified and validated and believed adequate for the intended use. If the machine or procedures

More information

Service Tools. Service and Repair Manual Model 900/950/990 ITEM PART NO. DESCRIPTION ITEM PART NO. DESCRIPTION ITEM PART NO.

Service Tools. Service and Repair Manual Model 900/950/990 ITEM PART NO. DESCRIPTION ITEM PART NO. DESCRIPTION ITEM PART NO. 12 1 3 2 4 5 8 10 6 7 9 11 14 24 12 13 17 22 29 18 23 25 19 26 15 20 27 21 16 22 33 37 38 32 31 36 30 34 35 40 41 42 43 ITEM PART NO. DESCRIPTION 1 9170 0231 30 LONG ALLEN KEY 2 9170 0737 20 3/32 PIN PUNCH

More information

Troubleshooting Guide: Elevance Delivery Systems

Troubleshooting Guide: Elevance Delivery Systems Troubleshooting Guide: Elevance Delivery Systems FOR USE BY MIDMARK TRAINED TECHNICIANS Contents Description / Links Troubleshooting Charts ICM Screens Assistant s Unit Instruments (Elevance & European)

More information

MANUAL TRANSMISSION SECTION MT CONTENTS TRANSMISSION/TRANSAXLE MT-1 SERVICE INFORMATION POSITION SWITCH...13 Checking...13

MANUAL TRANSMISSION SECTION MT CONTENTS TRANSMISSION/TRANSAXLE MT-1 SERVICE INFORMATION POSITION SWITCH...13 Checking...13 TRANSMISSION/TRANSAXLE SECTION MT A B MANUAL TRANSMISSION MT D CONTENTS E SERVICE INFORMATION... 2 PRECAUTIONS... 2 Service Notice or Precaution...2 PREPARATION... 3 Special Service Tool...3 Commercial

More information

Type 1051 and 1052 Size 33 Diaphragm Rotary Actuator

Type 1051 and 1052 Size 33 Diaphragm Rotary Actuator Instruction Manual Type 1051 and 1052 Size 33 Diaphragm Rotary Actuator 1051 & 1052 Actuator Contents Introduction............................. 1 Scope of Manual........................... 1 Description................................

More information

TECHNICAL INFORMATION

TECHNICAL INFORMATION TECHNICAL INFORMATION Model No. Description SP6000 Plunge Cut Circular Saw 165mm (6-1/2") CONCEPT AND MAIN APPLICATIONS Model SP6000 is the first Makita plunge cut saw. Features great conveniences such

More information

HURST COMP/PLUS SHIFTER 2015 Ford Mustang (Getrag MT82 six-speed manual transmission) Catalog # by Hurst Performance

HURST COMP/PLUS SHIFTER 2015 Ford Mustang (Getrag MT82 six-speed manual transmission) Catalog # by Hurst Performance FORM 159 0205 07/15 HURST COMP/PLUS SHIFTER 2015 Ford Mustang (Getrag MT82 six-speed manual transmission) Catalog #391 0205 2015 by Hurst Performance Thank you for purchasing the Hurst Comp/Plus Shifter.

More information

Introduction. Exploded View. Conveyor System - Troubleshooting Guide LAST UPDATED: 09/19/2018

Introduction. Exploded View. Conveyor System - Troubleshooting Guide LAST UPDATED: 09/19/2018 LAST UPDATED: 09/19/2018 Introduction 1. 2. 3. 4. Conveyor Drive Motor Power Cord Conveyor Drive Shaft /Sprockets 5. Belt 6. Belt Tensioning Screws Exploded View 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12.

More information

Monitor Support Arms. Service and Parts Manual Part / Kit Numbers:

Monitor Support Arms. Service and Parts Manual Part / Kit Numbers: Monitor Support Arms Part / Kit Numbers: 153698 153699 153705 002-1836-00 153762 153763 153798 153823 153824 Service and Parts Manual FOR USE BY MIDMARK TRAINED TECHNICIANS ONLY 004-0806-00 (7/30/15) Table

More information

FlexJet - Flex Cable Replacement

FlexJet - Flex Cable Replacement P/N: 109515R0 14140 NE 200th St. Woodinville, WA. 98072 PH: (425) 398-8282 FX: (425) 398-8383 FlexJet - Flex Cable Replacement Notices: Warning! Ensure that all AC power cables are removed from the printer

More information

SCION tc 2005 LEATHER STEERING WHEEL Preparation. Part Number: (Silver/Dark Gray)

SCION tc 2005 LEATHER STEERING WHEEL Preparation. Part Number: (Silver/Dark Gray) Preparation Part Number: 08460 21810 (Silver/Dark Gray) NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents Item # Quantity Reqd. Description 1 1 Steering Wheel

More information

Operating Manual & Safety Instructions ProTorc Hydraulic Torque Wrench Model # PTLC - Please read in full before operating ProTorc Torque Wrench -

Operating Manual & Safety Instructions ProTorc Hydraulic Torque Wrench Model # PTLC - Please read in full before operating ProTorc Torque Wrench - Operating Manual & Safety Instructions ProTorc Hydraulic Torque Wrench Model # PTLC - Please read in full before operating ProTorc Torque Wrench - ProTorc Important Safety Instructions READ ALL INSTRUCTIONS

More information