Metal Gasket Face Seal Fittings

Transcription

1 Metal Gasket ace Seal ittings Series IOK Group IOK GmbH (Headquarter) Sprendlinger andstr. 5, Offenbach am Main, Germany el.: ax: IOK, Inc North romenade lvd., Suite 750, Stafford, exas 77477, USA el.: ax: IOK Incorporated -4, lock, Zone, Yingtailong lndustrial ark, alang Street, onghua istrict, Shenzhen, 5809, hina el.: ax: IOK Middle ast Oil quipment rading , Makateb ower, Airport Road,.O.ox 8542, eira, ubai, UA el.: ax: info@fitokgroup.com K-I-S-0-N-504

2 Metal Gasket ace Seal ittings ontents - G odies - M, M,, U, U, U, W, RU, RA, R, M, U,, Welded - WG Nuts - N, MN, eatures Metal-to-metal seal provides perfect leak-tight service from critical vacuum to high pressure female threads are silver plated est port at nut for easy leak testing All seal faces and male threads are protected with plastic caps recision manufactured gasket for maximum performance very gland and body is stamped with size, material and heat code Standard surface finish is a roughness average of 0 μin. (0.25 μm) Ra. With 5 μin. (0.3 μm) Ra surface finish is available echnical ata s range from /6" to " and 6 mm to 8 mm. hread Specifications: 3 hread ype Reference Specification lugs - G aps - High-low onnections - G, W, W, U,, N, MN 4 4 N Unified (SA) Working ressure: a. atalog working pressure is calculated in accordance with ANSI/ASM 3.3. o determine working pressure in accordance with ANSI/ASM 3., multiply by b. Working pressure ratings are affected by the gasket material at room temperature. Working emperature: ASM.20., SA AS705 ASM., SA J475 Gaskets - G 5 7 omponent ittings Material 36 stainless steel 36 stainless steel 36 VAR stainless steel Working emperature 000 (538 ) low Restrictors Gaskets 36 stainless steel opper 400 (204 ) 7 Nickel 600 (36 ) Standard Materials of onstruction Material 36 stainless steel 36 stainless steel 36 VAR stainless steel 36 stainless steel opper Nickel ar Stock ASM A276, ASM SA479 SMI 20 itting Material Gasket Material ASM A240 ASM 52 ASM 62 orging ASM SA82, ASM A34 esignator SS 6 6V 6 U NI Materials traceable, certification available upon request

3 2 Metal Gasket ace Seal ittings Metal Gasket ace Seal ittings 3 esting -9 fitting is tested with helium at a maximum leak rate of 4 0 std cm 3 /s. Information imensions are for reference only and are subject to change. ach component should be ordered separately. Add the material designator as a prefix, technology grade as a suffix to the basic ordering number to get the complete ordering number. Standard rocess Specification -0 standard cleaning and packaging, Is applied to all the fittings for general industrial procedure. No suffix is required. xample: 6-G-2-2. Ultrahigh-purity rocess Specification -03 ultrahigh-purity cleaning and packaging, Assembly and packaging in class 00 clean circumstances. Wetted surfaces are finished to 5 μin. (0.3 μm) Ra. add - 3 as a suffix to the basic ordering number. xample: 6V-G Remark: Ultrahigh-purity process is only available for 36 and 36 VAR stainless steel fittings stainless steel and nickel gasket default technology grade is ultrahigh-purity process specification. No suffix is required. xample: 6-G-4. Installation Instructions. Assemble the gland, nut, gasket and male nut as below, finger tighten the nut. Gland to Short ractional ube utt Weld Wall hickness G-2-2-2S -G-4-2-2S -G-4-4-4S -G-4-4-6S -G-4-4-2S -G-8-4-2S -G-8-6-4S -G-8-6-2S -G-8-8-4S -G-8-8-6S -G-8-8-2S Gland to Short Metric ube utt Weld Wall hickness G-4-M6-2S -G-4-M8-2S -G-8-M0-2S -G-8-M2-2S -G-2-M8-2S.08 (27.4).0 (27.9) 0.60 (5.2) 0.72 (8.3).0 (27.9).2 (28.4) 0.62 (5.7).2 (28.4) 0.62 (5.7) 0.74 (8.8).2 (28.4) 29.5 (.6) 29.5 (.6) 29.5 (.6) 29.5 (.6) 3.0 (.22) 6 U NI 0.75 (9.) 0.75 (9.) 0.38 (9.6) 0.75 (9.) 0.75 (9.) 0.75 (9.) 0.38 (9.6) 0.75 (9.) imension, mm 0.06 (.5) 0.06 (.5) 0.8 (4.6) 0.8 (4.6) 0.8 (4.6) 0.8 (4.6) 0.3 (7.9) 0.3 (7.9) 0.40 (0.2) 0.40 (0.2) 0.40 (0.2) 8500 (586) 500 (35) 500 (35) 500 (35) 500 (35) 468 (6800) 337 (4900) 24 (3500) 23 (300) 206 (3000) 6800 (468) 500 (35) 500 (35) 500 (35) 500 (35) 2600 (79) 2600 (79) 372 (5400) 337 (4900) 92 (2800) 65 (2400) 65 (2400) 8500 (586) 500 (35) 500 (35) 500 (35) 500 (35) Working ressure, bar (psig) 6 U NI 9. (0.75) 9. (0.75) 9. (0.75) 9. (0.75) 9. (0.75) 4.0 (0.6) 6.0 (0.24) 8.0 (0.3) 0.0 (0.39) 5.0 (0.59) 468 (6800) 337 (4900) 24 (3500) 23 (300) 206 (3000) 2. or 36 stainless steel and nickel gasket material, tighten the nut turn with a wrench while holding the male nut or body of the fitting steady. ighten the nut turn for copper gasket. autions: Over-tightening will damage the sealing beads and possibly cause system leakage. he old gasket must be replaced by the new gasket for each assembly. ungsten Inert Gas Welding (IG) is recommended. Always use proper thread sealants on tapered pipe threads. o not loosen or tighten fittings when system is pressurized.

4 4 Metal Gasket ace Seal ittings Metal Gasket ace Seal ittings 5 x Gland to ong ractional ube utt Weld Gland to ong Metric ube utt Weld Wall hickness Wall hickness G G G G G G G G G G G G G G-4-M6-2 -G-4-M8-2 -G-8-M0-2 -G-8-M2-2 -G-2-M (36.).20 (30.5).3 (33.3).32 (33.5).70 (43.2).80 (45.7).29 (32.8).79 (45.5).29 (32.8).4 (35.8).79 (45.5) 2.03 (5.6) 2.32 (58.9) 43.2 (.70) 43.2 (.70) 45.5 (.79) 45.5 (.79) 5.6 (2.03) 6 U NI 0.75 (9.) 0.36 (9.) 0.38 (9.6) 0.75 (9.) 0.75 (9.) 0.75 (9.) 0.38 (9.6) 0.75 (9.) 0.75 (9.) 0.75 (9.) imension, mm 6 U NI 9. (0.75) 9. (0.75) 9. (0.75) 9. (0.75) 9. (0.75) 0.06 (.5) 0.8 (4.6) 0.8 (4.6) 0.8 (4.6) 0.8 (4.6) 0.8 (4.6) 0.3 (7.9) 0.3 (7.9) 0.40 (0.2) 0.40 (0.2) 0.40 (0.2) 0.65 (6.5) 0.87 (22.) 4.0 (0.6) 6.0 (0.24) 8.0 (0.3) 0.0 (0.39) 5.0 (0.59) 8500 (586) 500 (35) 500 (35) 500 (35) 500 (35) 2400 (65) 2400 (65) Working ressure, bar (psig) 24 ( 3500) 23 ( 300) 207 ( 3000) 6800 (468) 500 (35) 500 (35) 500 (35) 500 (35) 2600 (79) 2600 (79) 900 (30) 900 (30) 372 ( 5400) 92 ( 2800) 65 ( 2400) 65 ( 2400) 8500 (586) 500 (35) 500 (35) 500 (35) 500 (35) 2400 (65) 2400 (65) 24 ( 3500) 23 ( 300) 207 ( 3000) Short ractional Automatic ube utt Weld Wall hickness Wall hickness -AG-4-4-2S -AG-8-6-2S -AG-8-8-2S Short Metric Automatic ube utt Weld -AG-4-M6-2S -AG-4-M8-2S -AG-8-M0-2S -AG-8-M2-2S x x 6 U NI.2 (28.4).5 (29.2).6 (29.5) 0.75 (9.) 0.75 (9.) 0.75 (9.) 0.02 (0.5) 0.03 (0.8) 0.04 (.0) imension, mm 0.8 (4.6) 0.3 (7.9) 0.40 (0.2) 0.29 (7.4) 0.4 (0.4) 0.55 (4.0) 500 (35) 500 (35) 2600 (79) 500 (35) Working ressure, bar (psig) x 6 U NI 30.0 (.8) 30.2 (.9) 3.0 (.22) 30.5 (.20) 9. (0.75) 9. (0.75) 9. (0.75) 9. (0.75) 0.5 (0.02) 0.8 (0.03) 0.8 (0.03).0 (0.04) 4.0 (0.6) 6.0 (0.24) 8.0 (0.3) 0.0 (0.39) 6.8 (0.27) 8.9 (0.35) 0.9 (0.43) 3.2 (0.52) 24 ( 3500) 23 ( 300) 372 ( 5400) 92 ( 2800) 65 ( 2400) 24 ( 3500) 23 ( 300) he suffix -4, -6, -2 indicate the length of im., eg. SS-G-8-6-4, -4 means im =4/6 "* 25.4=6.4 mm. ong ractional Automatic ube utt Weld Wall hickness -AG AG AG AG AG x 6 U NI.72 (43.7).82 (46.2).82 (46.2).83 (46.5) 2.07 (52.6) 0.75 (9.) 0.75 (9.) 0.75 (9.) 0.75 (9.) 0.75 (9.) 0.02 (0.5) 0.02 (0.5) 0.03 (0.8) 0.04 (.0) 0.04 (.0) 0.8 (4.6) 0.8 (4.6) 0.3 (7.9) 0.40 (0.2) 0.65 (6.5) 0.29 (7.4) 0.29 (7.4) 0.4 (0.4) 0.55 (4.0) 0.80 (20.3) 500 (35) 2400 (65) 500 (35) 500 (35) 2600 (79) 2400 (65) 2400 (65) AG (65.3) 0.96 (24.4) 0.04 (.0) 0.87 (22.).06 (26.9) 2400 (65) 900 (30) 2400 (65) ong Metric Automatic ube utt Weld Wall hickness AG-4-M6-2 -AG-8-M2-2 imension, mm Working ressure, bar (psig) x 6 U NI 43.7 (.72) 46.5 (.83) -AG-2-M (2.07) 9. (0.75) 9. (0.75) 9. (0.75) 0.5 (0.02).0 (0.04).0 (0.04) 4.0 (0.6) 0.0 (0.39) 5.0 (0.59) 6.8 (0.27) 3.2 (0.52) 9.3 (0.76) 23 ( 300) 206 ( 3000) 372 ( 5400) 65 ( 2400) 65 ( 2400) 23 ( 300) 206 ( 3000)

5 6 Metal Gasket ace Seal ittings Metal Gasket ace Seal ittings 7 x Gland to Short ube Socket Weld x 6 U NI -G-4-S G-4-S x 0.50 (2.7) 0.75 (9.) 0.28(7.) 0.28(7.) 0.8(4.6) 0.8(4.6) 0.35(8.9) 0.35(8.9) Gland to Male Weld -G-2-2 -G-4-2 -G-4-4 -G-8-4 -G-8-6 -G-8-8 -G-2-2 -G U NI 0.70 (7.8) 0.28 (7.) 0.06 (.5) 200 (772) 7200 (496) 9000 (620).3 (33.3) 0.28 (7.) 0.06 (.5) 0000 (690) 8000 (55).3 (33.3) 0.4 (0.4) 0.2 (3.0) 0000 (690) 8000 (55).50 (38.) 0.4 (0.4) 0.2 (3.0).50 (38.) 0.4 (0.4) 0.28 (7.).50 (38.) 0.50 (2.7) 0.40 (0.2) 2.00 (50.8) 0.62 (5.7) 0.53 (3.5) 3700 (254) 2400 (65) 3000 (206) 2.22 (56.4) 0.8 (20.6) 0.75 (9.) 3000 (206) 900 (30) 2400 (65) Gland to ube Socket Weld /6 -G-2-S -G-2-S2 -G-4-S4 -G-8-S6 -G-8-S8 -G-2-S2 -G-6-S (7.8) 0.70 (7.8).3 (33.3).50 (38.).50 (38.) 2.00 (50.8) 2.22 (56.4) 0.0 (2.5) 0.05 (.3) 0.0 (2.5) 0.28 (7.) 0.8 (4.6) 0.3 (7.9) 0.28 (7.) 0.40 (0.2) 0.44 (.2) 0.62 (5.7) 0.62 (5.7) 0.87 (22.) x 6 U NI 0.3 (3.3) 9000 (620) 7200 (496) 9000 (620) 0.20 (5.) 700 (489) 700 (489) 700 (489) 0.35 (8.9) 0.60 (5.2) 0.60 (5.2) 3000 (206) 2400 (65) 3000 (206) 0.88 (22.4) 2200 (5).9 (30.2) 3000 (206) 900 (30) 2400 (65) Gland to ube ort -G-4-4 -G-8-6 -G U NI.62 (4.0) 0.64 (6.2) 0.7(4.3) 0000 (690) 8000 (55).8 (46.0) 0.70 (7.8) 0.27(6.9).94 (49.3) 0.96 (24.4) 0.37(9.4) Reducing Socket Weld x Reducing Socket Weld x 6 U NI -G-4-RS2 -G-8-RS4.3 (33.3).50 (38.) 0.0 (2.5) 0.28 (7.) 0.8 (4.6) 0.35 (8.9) 0.60 (5.2) 8000(55) 3500(24) 8000(55) 3500(24) 8000(55) 3500(24) lind Gland -G-2- -G-4- -G-8- -G-2- -G (7.8).3 (33.3).50 (38.) 2.00 (50.8) 2.22 (56.4)

6 8 Metal Gasket ace Seal ittings Metal Gasket ace Seal ittings 9 odies ody to SA/MS hread flat ody to Male N -N /6 -M-2-NS -M-2-NS2 -M-4-NS2 -M-4-NS4 -M-8-NS4 -M-8-NS6 -M-8-NS8 -M-2-NS2 -M-6-NS6 6 U NI.07 (27.2).07 (27.2).3 (33.3).49 (37.8).65 (4.9).65 (4.9).84 (46.7) 2.9 (55.6) 2.47 (62.7) 0.56 (4.2) 0.56 (4.2) 0.56 (4.2) 0.75 (9.) 0.75 (9.) 0.94 (23.9) 0.8 (4.6) 0.8 (4.6) 0.28 (7.) 0.40 (0.2) 0.62 (5.7) 0.87 (22.) (9.5) 7/6 (.) 5/8 (5.9) 5/8 (5.9) 5/6 (23.8) 5/6 (23.8) 5/6 (23.8) 5/6 (33.3) 5/8 (4.3) 9000 (620) 7200 (496) 9000 (620) 7200 (496) 0000 (690) 0000 (690) 3700 (254) 2400 (65) 3000 (206) 900 (30) 9000 (620) 9000 (620) 8000 (55) 8000 (55) 3000 (206) 2400 (65) -SA/MS hread 9/ 6-8 9/ 6-8 ody to SA/MS hread Uniform O-Ring M-4-S9 -M-8-S9 6 U NI ( 9. ) 5/6 ( 23. 8) 4500 (30) 4500 ( 30) 4500 (30) 3500 ( 24) 2800 ( 92) 3500 ( 24) 7/ M-8-S4.66 (42.2) 0.50 (2.7) 0.40 (0.2) 0.28 (7.) 0.59 (5.0) ( 25. 4) 3500 ( 24) 2800 ( 92) 3500 ( 24) luorocarbon KM is standard, other materials are available. odies.33 (33.8).48 (37.6) 0.39 (9.9) 0.39 (9.9) 0.8 (4.6) 0.28 (7.) 0.28 (7.) 0.28 (7.) x - Hex ody to emale N x ody to ulkhead Male onnector -N -M-4-NS4 -M-8-NS4 x x 2.2 (56.) 2.34 (59.4).24 (3.5).24 (3.5) 0.28 (7.) 0.28 (7.) 3/6 (20.6) 5/6 (23.8) -N /6 --2-NS --2-NS2 --4-NS2 --4-NS4 --8-NS6 --8-NS8 --2-NS2 --6-NS6 6 U NI.0 (27.9).9 (30.2).4 (35.8).54 (39.).76 (44.7).99 (50.5) 2.36 (59.9) 2.5 (63.8) 0.39 (9.9) 0.4 (0.4) 0.4 (0.4) 0.59 (5.0) 0.59 (5.0) 0.78 (9.8) 0.8 (20.6).00 (25.4) 0.8 (4.6) 0.8 (4.6) 0.40 (0.2) 0.40 (0.2) 0.62 (5.7) 0.87 (22.) 7/6 (.) 9/6 (4.3) 5/8 (5.9) (9.) 5/6 (23.8) /6 (27.0) 5/6 (33.3) 5/8 (4.3) 6700 ( 46) 6500 (447) 8000 (55) 6600 (454) 3700 (254) 6700 ( 46) 6500 (447) 5200 (358) 2400 (65) 900 (30) 6700 ( 46) 6500 (447) 8000 (55) 6600 (454) 2400 (65) 3/6 (20.6) 3/6 (20.6) Hole in. 2/32 (6.7) Max. hickness in. 6 U NI 8000 (55) 2/32 (6.7) 4370 (30) 8000 (55) ody to ube itting -U-4-2 -U-4-4 -U-8-6 -U U NI.53 (38.9).62 (4.).84 (46.7).95 (49.5) 0.50 (2.7) 0.60 (5.2) 0.66 (6.8) 0.90 (22.9) 0.8 (4.6) 0.28 (7.) 0.40 (0.2) 5/8 (5.9) 5/8 (5.9) 5/6 (23.8) 5/6 (23.8) 0000 ( 690) 0000 (690) 6400 ( 440) 8000 ( 55) 8000 (55) imension is typical finger-tight.

7 0 Metal Gasket ace Seal ittings Metal Gasket ace Seal ittings odies odies x - Hex x ulkhead Union ody ody to ulkhead ube itting Union x Hole in. Max. hickness in. Working ressure, psig (bar) 6 U NI x -U U-4.82 (46.2) 2.23 (56.6) 0.99 (25.).30 (33.3) 0.8 (4.6) 0.8 (4.6) (9.) (9.) Hole rill in. 9/32 (5.0) 9/32 (5.0) Max. hickness in. 6 U NI 0.3 (3.3) 0.44 (.2) 0000 (690) 0000 (690) 8000 (55) 8000 (55) -U-4-4 -U U-8-6 -U (57.2).88(47.8) 2.54(64.5) 2.74(69.6) imension is typical finger-tight. 0.60(5.2) 0.60(5.2) 0.66(6.8) 0.90(22.9).32(33.5).05(26.7).45(36.8).65(4.9) 0.8(4.6) 0.8(4.6) 0.28(7.) 0.40(0.2) 5/8(5.9) 5/8(5.9) 5/6(23.8) 5/6(23.8) 5/8(5.9) 5/8(5.9) (9.) 5/6(23.8) 5/32(.9) 5/32(.9) 9/32(5.0) 25/32(9.8) 0.40(0.2) 0000(690) 0.3(3.3) 0000(690) 0.44(.2) 0.50(2.7) 4300(296) 4300(296) 6400(440) 8000(55) 6400(440) 8000(55) 2800(92) 3500(24) 2800(92) 3500(24) -U U (54.4) 2.57 (65.3). (28.2).48 ( 37.6) 0.40 (0.2) 0.40 (0.2) /6 (27.0) /6 (27.0) 29/32 (23.) 29/32 (23.) 0.3 (3.3) 0.50 (2.7) x Union ody 6 U NI -U-2.3 (28.7) (9.5) 200 (772) 7200 (496) 9000 (620) -U-4.55 (39.4) 0.8 (4.6) 5/8 (5.9) 0000 (690) 8000 (55) -U-8.84 (46.7) 0.40 (0.2) 5/6 (23.8) -U-2 -U (62.0) 2.59 (65.8) 0.62 (5.7) 0.87 (22.) 5/6 (33.3) 5/8 (4.3) 3700 (254) 2400 (65) 900 (30) 2400 (65) ulkhead ody to ube utt Weld -W W-4-4 x.95(49.5) 2.36(59.9) 0.99(25.).30(33.0) emale Reducing Union -RU-4-2 -RU (9.) 0.75(9.).6 (29.5).4 (35.8) 0.8(4.6) 0.8(4.6) 0.22(5.6) 0.22(5.6) 0.75(9.) 0.75(9.) Hole rill in. 9/32(5.) 9/32(5.) Max. hickness in. 0.3(3.3) 0.44(.2) 6 500(35) 500(35) U 500(35) 500(35) 6 U NI 0.3 (3.3) (9.) /6 (27.0) 0000 (690) NI 500(35) 500(35) 8000 (55) Reducing Union -U (34.8) 0.8 (4.6) -U (43.4) 0.8 (4.6) 0.40 (0.2) 5/8 (5.9) 5/6 (23.8) (690) U NI 8000 (55) Reducing Adapter -RA-4-2 -RA-8-4 Reducing ushing.9 (30.2) (9.).4 (35.8) 0.8 (4.6) /6 (27.0) 6 U NI 0000 (690) 8000 (55) 6 U NI -R-4-2 -R (26.9).4 (35.8) 0.3 (3.3) 5/8 (5.9) 5/6 (23.8) 0000 (690) 8000 (55)

8 2 Metal Gasket ace Seal ittings Metal Gasket ace Seal ittings 3 Welded - lat x ody to Male N lbow -N -M-4-NS2 -M-4-NS4 -M-8-NS6 -M-8-NS8.07 (27.2).07 (27.2).45 (36.8).45 (36.8) x 0.87 (22.) 0.38 (9.6) 0.8 (4.6).05 (26.7) 0.56 (4.2) 0.8 (4.6).26 (32.0) 0.56 (4.2) 0.40 (0.2).45 (36.8) 0.75 (9.) 0.40 (0.2) (2.7) (2.7) 3/6 (20.6) 3/6 (20.6) 6 U NI 0000 (690) 8000 (55) 8000 (55) 8000 (55) 8000 (55) Welded Gland to Male N -N -WG-4-NS2 -WG-4-NS4 -WG-8-NS6 -WG-8-NS8.58 (40.).79 (45.5).89 (48.0) 2.09 (53.) 0.56 (4.2) 0.56 (4.2) 0.75 (9.) 0.8 (4.6) 0.8 (4.6) 0.40 (0.2) 0.40 (0.2) (9.) (9.) /6 (27.0) /6 (27.0) 7/6 (.) 9/6 (4.3) /6 (7.5) 7/8 (22.2) G 6 U NI 8000 (55) 8000 (55) 6400 (446) 6400 (446) 8000 (55) 8000 (55) odies ody Union lbow 6 U NI - lat -U-2 -U-4 -U-8 -U-2 -U-6.07 (27.2).45 (36.8).92 (48.8) 2.00 (50.8) 0.8 (4.6) 0.40 (0.2) 0.62 (5.7) 0.87 (22.) 7/6 (.) (2.7) 3/6 (20.6) (3.8) /6 (42.9) 200 (772) 0000 (690) 3700 (254) 7200 (496) 2400 (65) 900 (30) 9000 (620) 8000 (55) 2400 (65) Welded Gland to emale N -N -WG-4-NS4.77 (45.0) 0.59 (5.0) G 0.8 (4.6) (9.) (9.) (454) U NI 5200 (458) 6600 (454) -WG-8-NS6.95 (49.5) 0.59 (5.0) 0.40 (0.2) /6 (27.0) 7/8 (22.2) - lat ody Union ee U NI.07 (27.2).45 (36.8).92 (48.8) 2.00 (50.8) 0.8 (4.6) 0.40 (0.2) 0.62 (5.7) 0.87 (22.) 7/6 (.) (2.7) 3/6 (20.6) (3.8) /6 (42.9) 200 (772) 0000 (690) 3700 (254) 7200 (496) 2400 (65) 900 (30) 9000 (620) 8000 (55) 2400 (65) -WG-8-NS8 2.8 (55.4) 0.78 (9.8) 0.40 (0.2) /6 (27.0) /6 (27.0) Welded Gland to ube itting ody Union ross U NI 0.89(22.6) 0.09(2.3) 7/6 (.) 200 (772) 7200 (496) 9000 (620).07(27.2) 0.8(4.6) (2.7) 0000 (690) 8000 (55) -WG-4-4 -WG-4-6 -WG (49.3).97 (50.0) 2.23 (56.6) G 0.60 (5.2) 0.8 (4.6) (9.) 0.66 (6.8) 0.8 (4.6) (9.) 0.90 (22.9) 0.40 (0.2) /6 (27.0) (2.7) 5/8 (5.9) 3/6 (20.6) 6 U NI 8000 (55) 8000 (55) 6500 (447) 5200 (358) 6500 (447) (36.8) 0.40(0.2) 3/6 (20.6) imension is typical finger-tight. - lat (48.8) 0.62(5.7) (3.8) 3700 (254) 2400 (65) (50.8) 0.87(22.) /6 (42.9) 900 (30) 2400 (65)

9 4 Metal Gasket ace Seal ittings Metal Gasket ace Seal ittings 5 Welded Gland Union G 6 U NI - Nut Hex -WG-4 -WG-8.7 (43.4).84 (46.7) 0.8 (4.6) 0.40 (0.2) (9.) /6 (27.0) 8000 (55) 8000 (55) Short Male Nut oupling emale lbow emale ee ordering number: -WG-4 ordering number: -WG mm 25.4 mm -MN MN or use with short gland 0.54 (3.7) 0.36 (9.) 5/8 (5.9) 0.65 (6.5) 0.36 (9.) 5/8 (5.9) (6.8) 7/6 (.).9 (30.2) (9.).3 (33.3) /6 (27.0).68 (42.7) (38.) (5.8) (44.5) lugs aps Nuts - Nut Hex lug ap -G-2 -G-4 -G (7.3) 0.92 (23.4).08 (27.4) (9.5) 5/8 (5.9) 5/6 (23.8) (6.0) 0.94 (23.9).0 (25.6) G 7/6 (.) (9.) /6 (27.0) emale Nut Male Nut -G-2 -G-6.43 (36.3).52 (38.6) 5/6 (33.3) 5/8 (4.3) (32.8).54 (39.) (38.) (44.5) G -N-2 -N (3.5) 0.8 (20.6) 0.2 (5.3) 0.36 (9.) 7/6 (.) (9.) -MN-2 -MN (2.7) 0.7 (8.0) 0.2 (5.3) 0.36 (9.) (9.5) 5/8 (5.9) lug with anyard ap with anyard 5/8 -N-8 -N-0 -N (22.4) 0.88 (22.4).2 (28.4) 0.6 (5.5) 0.74 (8.8) /6 (27.0) 3/6 (30.2) (38.) 5/8 -MN-8 -MN-0 -MN (20.6) 0.8 (20.6).00 (25.4) 0.6 (5.5) 0.74 (8.8) 5/6 (23.8) /6 (27.0) 5/6 (33.3) anyard material is 304 satinless steel. anyard material is 304 satinless steel. anyard length is 5.2 cm. anyard length is 5.2 cm. -N-6.34 (34.0).20 (30.5) (44.5) -MN-6.9 (30.2).20 (30.5) 5/8 (4.3) Split-Nut Assemblies - Nut Hex - Nut Hex emale Split-Nut Nut Assemblies lug with anyard ap with anyard Split Nut ype emale Male -N-4-SN -MN-4-SN 0.8 ( 20.6) 0.60 (5.2) imension, in. ( mm) 0.36 (9.) 0.36 (9.) (9.) 5/8 (5.9) 0.63 (6.0) -G-4- -G (23.4).08 (27.4) 5/8 (5.9) 5/6 (23.8) (23.9).0 (25.6) G (9.) /6 (27.0)

10 6 Metal Gasket ace Seal ittings Metal Gasket ace Seal ittings 7 High-low onnections "H" ype or uniform flow, use " side-load retainer style gasket. Automatic ube Weld -flat ube utt Weld Wall hickness -G-H G-H G-H (5.2).9 (30.2).3 (33.3) 6 U NI 0.4 (0.4).00 (25.4).2 (28.4) 0.3 (7.9) 0.3 (7.9) 0.3 (7.9) Automatic ube Weld ube -AW-H4-6 6 U NI.7(43.4) 0.75(9.) 0.62(5.7) 0.03(0.8) 0.25(6.4) 0.3(7.9) 5/8(5. 9) 0.4(0.4) 3300(227) 3300(227) 3300(227) Union lbow odies flat - lat -U-H4.07 (27.2) (2.7) 6 U NI (690) 8000 (55) odies ube utt Weld 6 U NI -W-H (42.7) 0.75 (9.) 0.62 (5.7) 0.3 (7.9) 5/8 (5.9) - lat Union ee 6 U NI flat flat --H4.07 (27.2) (2.7) (690) 8000 (55) Nuts - Nut Hex ulkhead connector -W-H4-6 Hole ia Max hickness Hole ia 2.36(59.9) 0.75(9.).30(33.0) 0.3(7.9) 0.25(6.4) (9.) (9.) 9/32(5.0) 0.44(.2) 6 U NI 3300(227) 3300(227) 3300(227) emale -N-H N-H (20.6) 0.8 (20.6) 0.39 (9.9) 0.46 (.7) G (9.) (9.) Male -MN-H4 0.7 (8.0) 0.39 (9.9) 5/8 (5.9)

11 8 Metal Gasket ace Seal ittings Gaskets Nickel and opper gasket retainer assemblies use a 36 stainless steel retainer. opper gaskets are unplated. Side-load retainer style gaskets are not available in copper. lind (undrilled) gaskets are available in nonretained and retainer assembly styles, add- as a suffix to the ordering number. xample: -G-4-U-. Silver lated Unplated (U) annot be used in a gasket retainer assembly. Nonretained Gaskets Retainer Assembly 0.7 x 5/8 -G-2 -G-4 -G-8 -G-0 -G-2 x 0.26 (6.6) 0.47 (.9) 0.22 (5.6) 0.78 (9.8) 0.44 (.2) 0.9 (23.) 0.58 (4.7).4 (29.0) 0.66 (6.8) 0.7 x -G-4-A-U -G-8-A-U -G-2-A-U -G-6-A-U imension, mm x 0.50 (2.7) 0.79 (20.).4 (29.0).40 (35.6) 0.24 (6.) 0.44 (.2) 0.66 (6.8) -G-6.40 (35.6) Retainer and gasket must be used as an assembly. 0.7 x Gasket Retainer Assembly -G-4-A -G-8-A -G-2-A -G-6-A x 0.50 (2.7) 0.79 (20.).4 (29.0).40 (35.6) 0.24 (6.) 0.44 (.2) 0.66 (6.8) low Restrictors Working pressure 0000 psig (690 bar) x /8 in. flat 4.6 Unplated (U) ody to Male N x, in. 0.7 x Side-load retainer -G-4-AS-U -G-8-AS-U x 0.45 (.4) 0.75 (9.) 0.24 (6.) 0.43 (.0) ( 0. 38) ( ) ( ) ( ) ( ) ( ) ( ) 6V-R V-R V-R V-R V-R V-R V-R ( ) 6V-R ( ) 6V-R (. 06) 6V-R Unplated (U) (. 43) (. 270) 6V-R V-R (. 397) 6V-R x Nonretained -G-2-U -G-4-U x 0.26 (6.6) 0.47 (.9) 0.22 (5.6) (. 529) (. 65) (. 778) (. 905) ( ) ( 2. 59) ( ) 6V-R V-R V-R V-R V-R V-R V-R /8 -G-8-U -G-0-U -G-2-U 0.78 (9.8) 0.9 (23.).4 (29.0) 0.44 (.2) 0.58 (4.7) 0.66 (6.8) ( ) ( 2. 43) ( ) 6V-R V-R V-R G-6-U.40 (35.6)