BRIGGS IRRIGATION Operators Manual & Parts Manual R40 Hosereel Mounted Boom Irrigator

Size: px

Start display at page:

Download "BRIGGS IRRIGATION Operators Manual & Parts Manual R40 Hosereel Mounted Boom Irrigator"

Belinda Lucas
5 years ago
Views:

1 Revised August 2013 Serial Number: BRIGGS IRRIGATION Operators Manual & Parts Manual R40 Hosereel Mounted Boom Irrigator Briggs Irrigation Boyle Road CORBY Northamptonshire NN17 5XU Tel: (0) Fax: (0)

2 EC DECLARATION OF CONFORMITY MANUFACTURER Briggs (UK) Limited Boyle Road Corby Northamptonshire NN17 5XU England Tel: + 44 (0) Fax: + 44 (0) enquiries@briggsirrigation.co.uk Web: HOSE REEL BOOM MODEL: R40 This machine complies to BS EN292 Part (89/392/EEC) Signed on behalf of Briggs (UK) Ltd A M Colwill Director 1

3 List of Contents Page EC Declaration of Conformity 1 Introduction & Specification 3 Pressure Settings 3 Transport 4 Dimensions 4 Assembly & Commissioning 4 Positioning the R40 for Operation 5 Folding the R40 8 Maintenance 8 Risks & Precautions 8 Nelson 10 psi regulated S3000 flow chart 9 Nelson 20 psi regulated S3000 flow chart 10 Nelson 30 psi regulated S3000 flow chart 11 S3000 Spinner 12 Nelson Pressure Regulators 13 Hose Reel wind in speed/application rate chart for R40 (40m) 14 Hose Reel wind in speed/application rate chart for R40 (44m) 14 Hose Reel wind in speed/application rate chart for R40 (48m) 15 Spare Parts 16 Figure 1. R40 Chassis Figure 2. R40 Centre Section Figure 3. R40 First Section Figure 4. R40 Second Section Figure 5. R40 Third Section Figure 6. R40 End Section Figure 7. Nelson Pressure Regulator and S3000 Spray Jet Figure 8. R40 Lift Frame Kit for Briggs Range of Hose Reels This manual covers all variations of the Briggs R40 Hose Reel mounted boom range. 2

4 INTRODUCTION The Briggs R40 Booms have been designed, manufactured and tested for long life and trouble free operation. It is essential to read this manual before operating the Boom and follow the operation and maintenance schedules carefully. SPECIFICATION Regulated Pressure: 0.66 bar (10psi) 1.00 bar (15psi) 1.40 bar (20psi) 2.00 bar (30psi) Minimum Requirements - Pressure Settings 15psi for 10psi regulated spray Boom 20psi for 15psi regulated spray Boom 25psi for 20psi regulated spray Boom 35psi for 30psi regulated spray Boom Nozzle Specifications Nozzle Size No of Nozzles Flow per Nozzle Total Flow Nelson 3000 series 360º Sprayjets / Rotators Nelson 3000 series 180º Sprayjets / Rotators centre Nelson 3000 series 180º Sprayjets / Rotators end Total Flow gpm. m³/hr. 3

5 TRANSPORT It is the responsibility of all boom operators to check the regulations applicable in the country and area the machine is being used regarding width, height, and lights. When transporting on public roads without a width exemption and escort, the second and third section pressure regulators must be removed. The boom sections must be tied together and have wide load safety triangles fitted. Also care must be taken to allow for the Boom overhang when turning. Important Do not exceed 10 km/hr when towing. Excessive speed causes instability due to the Hose Reel rigid chassis design and high centre of gravity. DIMENSIONS TOTAL FOLDED LENGTH FOLDED WIDTH TRACK WIDTH 5.5 metres 3.3 metres metres ASSEMBLY & COMMISSIONING The R40 Hose Reel mounted boom has been fully flushed and pressure tested at the Briggs Irrigation Factory. Some parts are removed to make transportation of the boom from factory to site both safe and legal. All parts which have been removed have been number matched and should be carefully reassembled on site ensuring the numbers are in the correct order. For commissioning, position the Hose Reel and Boom for initial setting up as explained below: 4

6 POSITIONING THE R40 FOR OPERATION 1. Tow the Hose Reel into the position required to start the irrigation run. 2. Turn the hose drum on the turntable (if fitted) to line up with the centre of the irrigation run (see photograph on page 6). 3. Set the wheel track of the boom. This is done manually by loosening the locking bolts and sliding the wheel mounting legs out to the desired position. The locking bolts must be done up tightly to ensure there is no movement during the course of the run. The wheels can be set to span up to a width of 4m. 4. Lower the boom by operating the Hose Reel hydraulic leg/lift frame system. 5. Set Hose Reel for pull out position. 6. Open Boom support bracket on Hose Reel, unfold the first Boom section only and lock securely in position. Note the sections should be supported as they are opened. This process can now be repeated for the opposite side - see page 7, actions 1 (right hand sections) & 2 (left hand sections). Use the boom support handle to open the sections (see below). This enables the operator to hold and support the sections throughout the opening process. Boom support handle 7. Connect the tractor to the towing out bar on the boom and pull out the hose at a constant speed not exceeding 3km/h. 8. Once pulled out, remove the tractor and move at least 6m to provide sufficient clearance for opening the boom sections. 9. Lower the boom support leg on the highest 1 st section (see page 7 and follow actions 3 & 4 or 5 & 6). 10. Open the 1 st section boom support bracket on this side and unfold the second section, locking it in place (action 7 for the RH side of the boom or 10 for the LH side). Again use the boom support handle to support the sections throughout the opening process. Repeat for the third (actions 8 or 10) and end sections (action 9 or 11). 5

11. Repeat for the opposite side of the boom (actions 10, 11, 12 for the LH sections or 7, 8, 9 for the RH sections). 12. Raise the boom support leg and lock in place on the R40 1 st section with the pin and spring clip provided.

If starting a run with the Boom angled to suit a headland, ensure that it is set to the finishing headland in good time so that an end section does not protrude over a road or a track.

7 11. Repeat for the opposite side of the boom (actions 10, 11, 12 for the LH sections or 7, 8, 9 for the RH sections). 12. Raise the boom support leg and lock in place on the R40 1 st section with the pin and spring clip provided. 13. The quadrant locking system allows the Boom to be set at any angle in relation to the direction of the run to suit angled headlands. If starting a run with the Boom angled to suit a headland, ensure that it is set to the finishing headland in good time so that an end section does not protrude over a road or a track. Note the position of the 180º spray jet on the centre section must face away from the Hose Reel to avoid watering in front of the Boom. The boom is now ready for operation. Slowly open the hydrant, Hose Reel valves and start the pump. Engage the Hose Reel drive and set the wind in speed (see pages 13 and 14) for the Hose Reel wind in Speed charts. Setting up for Work Pulling Out R40 Unfolded Ready for Operation 6

8 Unfolding and Folding Procedures for the R40 Right Hand Side (RH) Left Hand Side (LH) RH 1 st Section 1 2 LH 1 st Section RH 2 nd Section 7 RH 3 rd Section 8 RH End Section 9 10,11,12, 7

9 FOLDING THE R40 1. Lower the boom support legs on both first sections (Page 7, actions 3 to 6) 2. Fold the outer section (end section) on the lower side of the Boom (action 9 for the Right Hand side or 12 for Left Hand side) into the third section and lock in the boom support bracket. Note it is important to use the boom support handle to support the section during the folding operation. Repeat for the third (either 8 or 11) and second sections (either 7 or 10) on the same side of the boom. 3. Repeat this on the other side of the irrigator (actions 9, 8, 7 for the Right Hand sections or 12, 11, 10 for the Left). 4. Raise the boom support legs and lock into position on the 1 st sections (actions 3 to 6). 5. If necessary, turn the hose drum on the Hose Reel turntable to line up with the centre of the boom. 6. Fold the first section around the Hose Reel and clamp into the Hose Reel Boom support bracket (action 2). Repeat for opposite side (action 1) 7. Raise the boom using the hydraulic system on the hosereel. 8. If you are moving to another irrigation run, the boom can be transported at 90 degrees to the direction of travel. If you are moving to another field you must rotate the drum so that the hosereel and boom are in the road transport position. MAINTENANCE 1. Grease the turntable weekly. 2. Grease the rear wheel bearings weekly and repack / adjust annually. 3. Grease the front wheel acetyl bushes weekly on both sides, rotate wheel while greasing. 4. Grease front wheel steering king pin weekly. 5. Ensure Boom support brackets are holding the Boom centrally. Adjust if necessary. 6. Boom locking joint tension must be checked regularly and is adjusted by slackening the locking bolt and turning the offset catch cam. Keep regularly greased for ease of operation. RISKS AND PRECAUTIONS Ensure all locking pins are fully closed on the boom support brackets when transporting or pulling out the boom. Always transport the boom with great caution both on the road and in the field. Always secure Booms together with ropes or straps, together with the turntable pin when moving on public roads. Watch out for turning clearance of the Boom section when manoeuvring around vehicles or any other objects. When operating with obstacles in the field (poles etc) ensure the operator is present to rotate the Boom around the obstacle. If starting a run with the Boom angled to suit a headland, ensure it is set to the finishing headland angle in good time so an end section does not protrude over a road or track. 8

10 10psi Spray Head Performance Chart IMP GPM (M³/hr) 3TN Nozzle Sizes (Revised 29/04/99) Base psi #24 #25 #26 #27 #28 #29 #30 #31 #32 #33 #34 Colour red red white white blue blue dark brown dark brown orange orange dark green (0.72) 2.86 (0.78) 3.1 (0.85) 3.34 (0.91) 3.58 (0.98) 3.84 (1.05) 4.11 (1.12) 4.38 (1.2) 4.66 (1.27) 4.96 (1.35) 5.25 (1.43) 9 Base psi #35 #36 #37 #38 #40 #42 #44 #46 #48 #50 Colour dark green purple purple black dark turquoise mustard maroon cream dark blue copper (1.52) 5.88 (1.61) 6.2 (1.7) 6.53 (1.78) 7.23 (1.97) 7.93 (2.17) 8.7 (2.4) 9.4 (2.57) 10.3 (2.81) (3.04) 9

11 20psi Spray Head Performance Chart IMP GPM (M³/hr) 3TN Nozzle Sizes (Revised 29/04/99) Base psi #24 #25 #26 #27 #28 #29 #30 #31 #32 #33 #34 Colour red red white white blue blue dark brown dark brown orange orange dark green (1.01) 4.0 (1.1) 4.4 (1.19) 4.7 (1.28) 5.1 (1.39) 5.4 (1.48) 5.8 (1.59) 6.2 (1.83) 6.6 (1.81) 7.1 (1.93) 7.5 (2.05) 10 Base psi #35 #36 #37 #38 #40 #42 #44 #46 #48 #50 Colour dark green purple purple black dark turquoise mustard maroon cream dark blue copper (2.16) 8.3 (2.27) 8.9 (2.42) 9.4 (2.56) 10.4 (2.84) 11.6 (3.15) 12.7 (3.45) 13.9 (3.78) 15.2 (4.13) 16.4 (4.74) 10

12 30 PSi Spray Head Performance Chart IMP GPM (M³/hr) 3TN Nozzle Sizes (Revised 29/04/99) Base psi #24 #25 #26 #27 #28 #29 #30 #31 #32 #33 #34 Colour red red white white blue blue dark brown dark brown orange orange dark green (1.24) 4.9 (1.34) 5.3 (1.46) 5.7 (1.56) 6.2 (1.7) 6.7 (1.82) 7.1 (1.94) 7.6 (2.06) 8.1 (2.22) 8.7 (2.36) 9.2 (2.51) 11 Base psi #35 #36 #37 #38 #40 #42 #44 #46 #48 #50 Colour dark green purple purple black dark turquoise mustard maroon cream dark blue copper (2.65) 10.2 (2.78) 10.9 (2.97) 11.5 (3.14) 12.8 (3.49) 14.2 (3.86) 15.5 (4.23) 17.0 (4.63) 18.6 (5.06) 20.1 (5.47) 11

13 S3000 Spinner Gentle, rain-like droplets - ideal for sensitive soils and crops. Very low pressure operation Excellent uniformity Good wind-fighting capability 3/4 adapter 3TN Nozzle FASTER, EASIER NOZZLE CLEANING AND CHANGING: A quick change adapter allows removal of the sprinkler for easy cleaning of a plugged nozzle without tools and without shutting down the system NEW USER FRIENDLY PACKAGING SYSTEM: Nelson 3000 Series sprinklers and 3TN nozzles are packaged for faster, easier and more accurate installation in the field. Spinner Body NOZZLE SIZE (128 th inch increments) (eg 27/128 th inch orifice size) Spinner Plates Spinner Cap Assembly COLOUR STRIPE (odd numbered nozzles have a colour stripe of the next size) 12

14 13 FEATURES: NELSON BLUE TOP PRESSURE REGULATORS Precision Accuracy in tough field environments PATENTED DAMPING SYSTEM BLUE TOP The patented O-Ring Dampening System of Colour-Coded Identification all Nelson Pressure Regulators handles severe pressure surges, without creating flow Patented Internal restrictions under working pressures. Dampening System EXTENDED FLOW RANGE - Retards Vibration The Nelson Lo-Flo Pressure Regulator extends - Withstands to 10 gpm, providing economical precision. - Water Hammer EXTENDED ACCURACY Vented for Below Ground Use Precision components coupled with an internally lubricated o-ring minimize frictional drag and Chemically Resistant Materials hysteresis. PLUG RESISTANT DESIGN Internally Lubricated O-Ring An open seat design prevents hair-pinning, for Precision Accuracy debris hangup and plugging of the pressure regulator. Plug Resistant Seat Design PRECISION MANUFACTURED Made of the toughest chemically resistant Materials. 100% water tested for accuracy. Application Notes Performance Tables. Design Considerations Contact the Nelson factory for detailed Maintain a 3 psi threshold Performance information. above the normal spray rated pressure. Statement of Expected Performance. CAUTION! Nelson Pressure Regulators are accurate to 6% Pressure regulators should due to variance of coefficient in manufacturing. be installed downstream from all shut off valves. HI FLO PSI BAR GPM M³/HR

15 Hose Reel wind in Speed Charts for Application rate range. APPLICATION RATE Chart Showing Wind In Speeds For Required Application Rate (metres per hour) R40 Boom Water Flow - imperial gpm + m³/hr Lane Spacing 40m imperial gpm M³/hr mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm APPLICATION RATE Chart Showing Wind In Speeds For Required Application Rate (metres per hour) R40 Boom Water Flow - imperial gpm + m³/hr Lane Spacing 44m imperial gpm M³/hr mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm

16 APPLICATION RATE Hose Reel wind in Speed Charts for Application rate range. (cont.) Chart Showing Wind In Speeds For Required Application Rate (metres per hour) R40 Boom Water Flow - imperial gpm + m³/hr Lane Spacing - 48m imperial gpm M³/hr mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm

Revised August BRIGGS IRRIGATION Spare Parts Manual for R18, R24, R30 Hosereel Mounted Boom Irrigators

Revised August BRIGGS IRRIGATION Spare Parts Manual for R18, R24, R30 Hosereel Mounted Boom Irrigators Revised August 2013 BRIGGS IRRIGATION Spare Parts Manual for R18, R24, R30 Hosereel Mounted Boom Irrigators 16 Figure 1. Chassis (R18, R24, R30) 17 Figure 1. Chassis (R18, R24, R30) Item Description Part