AAA TECHNOLOGY & SPECIALTIES CO., INC

Transcription

1 TRI*CORE SINGLE INTERNAL/EXTERNAL OR DOUBLE-WALLED COMPOSITE "PATENT PENDING" AAA TECHNOLOGY & SPECIALTIES CO., INC Celerating 9 Years of Service to Industry Since 97

2

3 Introduction to TRI*CORE TRI*CORE is another premier Composite Insulation Shield exclusive from AAA TECHNOLGY & SPECIALTIES CO., INC. This product designed as a composite reinforced material can be up to 0 times stiffer and at least 0 times stronger than Polyurethane Insulation alone, depending on thickness and selected densities. It is used for areas that will be exposed to rubbing, vibration or small impact loadings while dramatically increasing strength. It replaces the need for a vapor barriers, internal shieldings and the use of mastics. TRI*CORE acts as a second skin protection, reinforcing the contact surface. The Fiberglass reinforced materials bonded to the Polyurethane Foam core acts as a continuous multi-directional "I-Beam", which is proportionally stronger and stiffer depending on the thickness and density of the insulation. Made from molded Fiberglass reinforced Vinyl Ester and Epoxy resins bonded to Polyurethane Foam, TRI*CORE Insulation provides a non-conductive surface that enhances the compressive strength of the Polyurethane. It further can be glued directly to the pipe using epoxy adhesives. Being non-metallic this product not only insulates but also prevents surface induced corrosion by keeping out moisture while also isolating from electrical continuity and has a superior chemical resistance. Our TRI*CORE Pipe Supports insulates from induced electrical currents that may filter from the ground acting as a barrier that can cause localized corrosion to your pipeline while also inhibiting electrical shock. It further is lighter and more transportable, speeding up installations and reducing transportation costs. These combined materials provide greater bearing strengths while at the same time acting as a corrosion, electrical and insulation barrier. TRI*CORE is available as an Internal/External or Double-Walled Composite Polyurethane sandwiched material. When used as a single composite over/under the Polyurethane Insulation the contact surface acts as a wear pad, capable of handling some friction and protecting the foam component internally or externally, while adding additional strength as a "T-Beam". The double-walled version protects the insulation both internally and externally and acts as a continuous "I- Beam", for enhanced strength and rigidity. Light Duty TRI*CORE composites insulation is typically used with a single composite internal or external pad bonded to the Polyurethane which is made of 2 lb/in² to lb/in² density insulation. UV mastic coating can be added to any exposed surfaces. Medium Duty TRI*CORE composites is used with a medium density foam of 8 lb/in² to lb/in² with either an internal or external composite surface. In medium duty applications, double-walled surfaces can be added for internal and external support where enhanced strength characteristics where needed. Heavy Duty TRI*CORE composites is used with lb/in² to 20 lb/in² density foam with either an internal or external composite surface. The composite component can also be thicker to increase strength and is used preferably for heavy load applications as double-walled high density Polyurethane foam core. TRI*CORE Pipe supports can be used with our standard galvanized or painted steel pipe supports or our exclusive TRI*COMPOSITE Pipe Supports, please refer to our Composite Catalog for additional details. Our Pipe Supports are optionally available with our TRI*SLIDE Low Friction Slide Bearings that allow axial movement that can be guided or directionally constrained. Please refer to our TRI*SLIDE catalog for types, capacities and sizing for your slide bearing needs. These are stainless over stainless or PTFE over stainless and even Graphite over stainless as described in our TRI*SLIDE guides.

4 TABLE OF CONTENTS Polyurethane Properties...,, 5 Testing and Scope of Work Shipping & Handling Correspondence Model Numbers and Description....9 Single Outer Reinforced Insulation Double-Walled Reinforced Insualtion Shoe Support Type..... Graphical Selection Guide...., SWP DWP SWP DWP SWP - 80MS DWP - 80MS SWP - 0BC DWP - 0BC.... SWP - 80MS - FB....2 DWP - 80MS - FB..... SWP - 0BC - FB DWP - 0BC- FB....2 SWP - 0BC - DW

5 TABLE OF CONTENTS DWP - 0BC - DW SWP - 0BC - DW - GC 29 DWP - 0BC - DW - GC... 0 SWP - 0BC - DW - BG... DWP - 0BC - DW - BG. 2 SWP - 0BC - DW - AG... DWP - 0BC - DW - AG. SWP - 0BC - DW - ST.. 5 DWP - 0BC - DW - ST.. SWP - 0BC - DW - ST & AG... 7 DWP - 0BC - DW - ST & AG. 8 SWP HCV... 9 DWP HCV. 0 SWP HC. DWP HC. 2 SWP FS... DWP FS. SWP FS.. 5 DWP FS... SWP FS DWP FS

6 TRI*CORE High Density Polyurethane Pipe Supports For Low Temperature Applications This specification has been prepared to set forth the requirements for the design, the manufacturing, the proper selection and the use of low temperature, load bearing, insulated pipe supports. This specification covers low temperature, load bearing, insulated pipe supports for use with piping systems operating at temperatures between -25 F (-25 C) to F (5 C). General Requirements. All low temperature, insulated piping shall be supported using insulated pipe supports. 2. All insulated pipe supports shall comply with the latest editions of the following piping codes and Manufacturer'sStandards: a. ANSI/ASME B. Power Piping Code b. ANSI/ASME B. Refinery and Chemical Plant Piping Code c. ANSI/ASME B. Liquid Petroleum Piping Code d. ANSI/ASME B.5 Refrigeration Piping Code e. ANSI/ASME B.8 Gas Transmission and Distribution Piping Code f. Manufacturer's Standardization Society MSS SP-58 g. Manufacturer's Standardization Society MSS SP-9 h. Manufacturer's Standardization Society MSS SP-89 i. Federal Specification WW-H-7D. The selection of all low temperature, load bearing, insulated pipe supports shall be based upon the following considerations: a. Maximum design loads that will be applied to the pipe support along the vertical, axial and lateral axes from the primary and secondary loadings. b. Maximum test loads that will be applied to the pipe support along the vertical, axial, lateral axes. c. Maximum design load that may be applied to the pipe support along the vertical, axial and lateral axes from occasional loading such as water hammer, seismic or impact type loads. d. Maximum deflection and rotations along the vertical, axial and lateral axes that are expected to occur and in what condition normal operating, testing, upset, seismic, water hammer, etc. e. Lowest possible temperature expected to occur in the piping system. f. Highest possible temperature expected to occur in the piping system. g. Highest and lowest possible ambient temperature expected to be experienced. h. Any dimensional clearances that may require during installation, testing or operating piping system. i. Any localized welds or lug that is to be covered properly by low temperature, load bearing.

7 TRI*CORE High Density Polyurethane Pipe Supports For Low Temperature Applications. At the request of the Owner, design calculations and supporting data shall be made available. 5. At the request of the Owner, piping stress analysis calculations shall be made available as well as Calculations indicating the stresses in the pipe wall at any attachment/lug juncture.. At the request of the Owner, material test reports or certified mill test reports may be requested. TRI*FOAM High Density Polyurethane Properties. High density polyurethane shall have the following properties: a. lb/ft³ foam i. Thermal Conductivity =. BTU-in/ft³ - hr deg F (Imperial), 0.0 W/meter*K (SI) ii. Thermal Resistance =. hr deg F - ft³ / BTU (Imperial),. m² - K/W (SI) iii. Density = lbs/ft³ (Imperial), 9. Kg/M³ (SI) (+/- 5%) iv. Ninety-five percent of the cells are closed v. Water absorption =.05 lbs/ft³ (Imperial),.8055 Kg/m³ b. 0lb/ft³ foam i. Thermal Conductivity =.7 BTU-in/ft³ - hr deg F (Imperial), 0.0 W/meter*K (SI) ii. Thermal Resistance = 5.9 hr deg F - ft³ / BTU (Imperial),.0 m² - K/W (SI) iii. Density = 0 lbs/ft³ (Imperial), 0. Kg/M³ (SI) (+/- 5%) iv. Ninety-five percent of the cells are closed v. Water absorption =.05 lbs/ft³ (Imperial),.8055 Kg/m³ c. 5lb/ft³ foam i. Thermal Conductivity =.9 BTU-in/ft³ - hr deg F (Imperial), W/meter*K (SI) ii. Thermal Resistance = 5. hr deg F - ft³ / BTU (Imperial), 0.90 m² - K/W (SI) iii. Density = 5 lbs/ft³ (Imperial), Kg/M³ (SI) (+/- 5%) iv. Ninety-five percent of the cells are closed v. Water absorption =.05 lbs/ft³ (Imperial),.8055 Kg/m³ d. 20lb/ft³ foam i. Thermal Conductivity =.25 BTU-in/ft³ - hr deg F (Imperial), 0.05 W/meter*K (SI) ii. Thermal Resistance =.2 hr deg F - ft³ / BTU (Imperial), 0.7 m² - K/W (SI) iii. Density = 20 lbs/ft³ (Imperial), 20.9 Kg/M³ (SI) (+/- 5%) iv. Ninety-five percent of the cells are closed v. Water absorption =.05 lbs/ft³ (Imperial),.8055 Kg/m³ 2. No CFC's shall be used in the fabrication process and no CFC's shall be contained in the high density polyurethane pipe supports to be supplied.

8 TRI*CORE High Density Polyurethane Pipe Supports For Low Temperature Applications TRI*FOAM High Density Polyurethane Saddle Properties. The high density polyurethane saddle shall have the following properties: a. The insulation I.D. and the dimensions shall be manufactured in accordance with the ASTM Specification C 5 unless otherwise specified. b. The saddle shall be provided fully assembled with sufficient high density polyurethane insulation extending beyond the support outer metal jacket in order to enable the insulator to make standard butt joints. c. The exposed polyurethane surfaces shall be coated with mastic to protect the foam from ultraviolet light degradation and moisture. Mastic used shall have a minimum perm rating of.02 in accordance with ASTM E-9. d. A vapor barrier shall be provided between the jacket and the high density polyurethane insulation with amaximum perm rating of.02. e. The high density polyurethane pipe support assembly shall be designed to provide for a sufficient clamping force on the pipe to assure that the pipe support assembly will move axially with the pipe. The axial loading conditions shall not exceed the design loads for which the pipe support assembly has been designed. TRI*FOAM Saddle Properties- Others. The saddle shall have the following properties for components other than the Polyurethane Saddle: a. All structural shapes and plate shall be of ASTM A-, unless otherwise specified. b. All bolts/studs greater than ¼" in diameter shall be of ASTM A-9, Grade B7, unless otherwise specified. c. All bolts and nuts less or equal to ¼" in diameter shall be ASTM A-07, unless otherwise specified. d. All Nuts greater than ¼" in diameter shall be ASTM A-9, Grade B7, unless otherwise specified. e. All high density polyurethane pipe support assemblies selected with a low friction slide plate assembly shall have two slide plate surfaces at each support point. Each slide plate assembly shall consist of a mating slide plates as follows: i. Top - / thick glass filled reinforced PTFE bonded to a 0 ga. Carbon steel backing plate; Bottom - / thick glass filled reinforced PTFE bonded to a 0 ga. Carbon steel backing plate. ii. Top - /" thick stainless steel plate welded to 0 ga. Carbon steel backing plate; Bottom - / thick glass filled reinforced PTFE bonded to a 0 ga. Carbon steel backing plate. iii. Top - /" thick stainless steel plate welded to 0 ga. Carbon steel backing plate; Bottom - ¼" thick polyurethane slide bearing box restrained on a 0 ga. Carbon steel backing plate. iv. For slide bearing assembly details, see the TRI*SLIDE literature published by AAA Technology and Specialties Co., Inc. 5

9 TRI*CORE High Density Polyurethane Pipe Supports For Low Temperature Applications Testing Standards for TRI*FOAM High Density Polyurethane Saddle. At the request of the owner, supplier shall provide compressive strength and thermal testing results of high densitypolyurethane saddles conducted by an independent testing laboratory in accordance to MSS SP-89. Testing of high density polyurethane samples shall take place at a temperature of -250 F (-5 C). 2. All tests performed to determine the load bearing capabilities of high density polyurethane saddles shall be conducted in accordance with ASTM D, Standard Test Method for Compressive Properties of Rigid Cellular Plastics.. A safety factor of 5.0 shall be used in determining maximum loads to be resisted by the high density polyurethane pipe supports at the design temperature.. All tests performed to determine the thermal conductivity of high density polyurethane saddles shall be conducted in accordance with ASTM C 77-, Steady State Heat Flux Measurements and Thermal Transmission Properties by means of the Guarded Hot Plate Apparatus. Scope of Work. All high density polyurethane pipe support assemblies shall include: a. The high density polyurethane saddle(s), b. The vapor barrier, c. The metal jacket, d. The fabricated steel casing, e. The low friction slide bearings, if specified by owner, f. The guide and line stops, if specified by owner, g. Tagging, and h. Any associated pipe hanger hardware or structural members, if specified by owner. 2. All pipes are the responsibility of the purchaser.. All non-load bearing insulation is not the responsibility of the purchaser.. All items not clearly identified as being required from the pipe support manufacturer shall be the responsibility of the purchaser.

10 TRI*CORE High Density Polyurethane Pipe Supports For Low Temperature Applications Shipping and Handling. Each high density polyurethane pipe support assembly shall be clearly and permanently marked with the support Identification number as specified by the owner. The marking shall be permanent in nature and shall withstand water and fading when exposed to sunlight for a minimum period of five (5) years. 2. The mark shall be placed on the high density polyurethane pipe support assembly in a location that is visible and readable to an observer from ten (0) feet away from the pipe support assembly.. Each high density polyurethane pipe support shall be shipped on a pallet with reinforced cardboard protection for all exposed polyurethane surfaces or in a reinforced cardboard box strong enough to prevent damage while assembly is in transit. Care shall be taken when packaging the high density polyurethane pipe support assemblies so that damage shall not occur when individual pipe support assemblies shift during shipment. All high density polyurethane pipes support assemblies shall be individually wrapped in plastic.. Each container shall be clearly marked with a unique number and each container shall have an individual packing list in the container as well as attached to the outside of the container. 5. Prior to installation in the Owner's plant, the high density polyurethane pipe support assemblies shall be stored in a dry covered area to avoid exposure to rain, moisture and sunlight.. At the time of the shipment, the supplier shall furnish installation instructions necessary for the proper installation of each style of high density polyurethane pipe support assemblies being provided. Quotations. All quotations for the pipe supports defined herein shall be submitted to. 2. All quotations for the pipe supports defined herein shall be for all components defined herein. In the event that you wish to submit a quotation for an alternate item, you must first define your price for the item and then define your alternate, its costs and the advantage of your alternate offers.. The manufacturer of all pipe supports defined herein shall be AAA Technology and Specialties Co., Inc., 29 Brittmoore Road, Houston, Texas or an approved equal. AAA Technology may be contacted by at info@aaatech.com or by telephone at (7) 89- or by Fax at (7) All quotations must include unit and extended pricing for each pipe support assembly. In addition, a total price for all items proposed are to be supplied. 7

11 TRI*CORE High Density Polyurethane Pipe Supports For Low Temperature Applications Correspondence. All correspondence, drawings and other data must have the inquiry number or the order number marked on it prominently. 2. All correspondence relating to the design or any engineering data for the pipe supports covered under this inquiry shall be sent to:.. All correspondence relating to any shipping information including weights and dimensions, and changes orders or specification not covered by formal Change Order to the Purchase Order shall be sent to:. Delivery. All pipe supports are to be delivered to the job site by. 2. The job site is located at:. 8

12 Model Numbers and Description TRI*CORE Reinforced Polyurethane Pipe Supports Pipe Size Cold Shoe are Code with Type, Size, Dimension and Material as Follow: Example: - SWP0BC - "x " - DW/S/GP - "Ins. - AG/HD Mean Single Wear Pad 0 and Type Saddle BOP and Length Insulation Thick Pipe Shoe Type Slot Option and Gusset Plate Support and Duty TYPE Model Numbers and Description of Code Type Description of Slot Option Type Description of Supprot S Expansion Slot FB Flat Bottom S2 Insulation Band Slot BG Beam Guide S Expanison Slot & Insulation Band Slot CG Clip Guide GP Gusset Plate AG Angle Guide RIB Rib Plate ST Line Stop AG& ST Angle Guide & Line Stop Type Description of Saddle FS Foam Support HDC Hold Down CLamp HC Hanger Clamp HCV Hanger Clevis Type Description of Pipe Shoe BC Body Clamp T Tee MS Metal Saddle DW Double Web 9

13 Detail of 80 deg. and 0 deg. TRI*CORE Reinforced Polyurethane Pipe Supports SINGLE WEAR PAD 80 degree one layer If Insulation is thicker than, two layers shall be used. 80 degree double layer 80 degree one layer 80 degree double layer WEAR PAD. WEAR PAD " TYP. TYP. Detail of one layer with saddle Detail of two layer with Saddle 0

14 Detail of 80 deg. and 0 deg. TRI*CORE Reinforced Polyurethane Pipe Supports DOUBLE WEAR PAD 80 degree one layer If Insulation is thicker than, two layers shall be used. 80 degree double layer 80 degree one layer 80 degree double layer WEAR PAD. WEAR PAD WEAR PAD. WEAR PAD. " TYP. TYP. Detail of one layer with saddle Detail of two layer with Saddle

15 Slot Option Detail TRI*CORE High Density Pipe Shoe Support TYPE S TYPE S2 Expansion Slot Insulation Band Slot TYPE S TYPE GP Insulation Band & Expansion Slot Gusset Plate

16 SWP -80 DWP - 80 PAGE 5 PAGE SWP - 0 DWP - 0 PAGE 7 PAGE 8 SWP - 80MS DWP - 80MS SWP - 0BC DWP - 0BC PAGE 0 PAGE 20 PAGE 2 PAGE SWP - 80MS - FB DWP - 80MS - FB SWP - 0BC - FB DWP - 0BC - FB PAGE 2 PAGE PAGE 25 PAGE 2 SWP - 0BC - DW DWP - 0BC - DW PAGE 27 PAGE 28 SWP - 0BC - DW - GC DWP - 0BC- DW- GC PAGE 29 PAGE 0 SWP - 0BC - DW - BG DWP - 0BC - DW - BG PAGE PAGE 2 SWP - 0BC - DW - AG DWP - 0BC- DW- AG PAGE PAGE

17 SWP - 0BC - DW - ST DWP - 0BC - DW - ST SWP - 0BC - DW - ST & AG DWP - 0BC - DW - ST & AG PAGE 5 PAGE PAGE 7 PAGE 8 SWP HCV PAGE 9 DWP HCV PAGE 0 SWP HC DWP HC PAGE PAGE 2 SWP FS DWP FS PAGE PAGE SWP FS DWP FS PAGE 5 PAGE SWP FS PAGE 7 DWP FS PAGE 8

18 SWP - 80 SINGLE WEAR PAD. " TYP. "F" * Temperature Range : -25 Degree * Exposted Polyurethane Surface are coated with * (-25 Degrees C ) to Degrees F (5 Degrees C) Monolar Mastic. * Light or Medium Load Capacity * Support Saddles are constructed in accordance * Design Load are Based on a Safety Factor of 5 with the MSS - SP58 and the ASME B Piping * Support Saddle are constructed on High Density * Technical Specification: AAAT - CS * Support Saddle restrains - Y movement. 5 5 /" 2 " 5 55 /" 2 " " 2 " " 0" " " " " LIGHT PAD THK. /" /" /" /" /" /" /" /" /" /" /" /" /" /" /" /" / / / 2 " " " / " " " " " 5 THICKNESS - / 2 " " 8 2- / 2 " 8 " 8 - / 2 " " 8 " 8 " 8 " 8 " " " " " " 7" 9" " " " 7" " 0 " " " 9" 2 29" 0 " 0 " " 7" 9" " 8 0 " 0 " " " " " 2 " 8 0 " 0 " " " " " " 7" 9" "

19 DWP - 80 DOUBLE WEAR PAD " TYP. "F" * Temperature Range : -25 Degree * Exposted Polyurethane Surface are coated with * (-25 Degrees C ) to Degrees F (5 Degrees C) Monolar Mastic. * Light or Medium Load Capacity * Support Saddles are constructed in accordance * Design Load are Based on a Safety Factor of 5 with the MSS - SP58 and the ASME B Piping * Support Saddle are constructed on High Density * Technical Specification: AAAT - CS * Support Saddle restrains - Y movement. 5 5 /" 2 " 5 55 /" 2 " " 2 " " 0" " " " " LIGHT PAD THK. /" /" /" /" /" /" /" /" /" /" /" /" /" /" /" /" / / / 2 " " " / " " " " " 5 THICKNESS - / 2 " " 8 2- / 2 " 8 " 8 - / 2 " " 8 " 8 " 8 " 8 " " " " " " 7" 9" " " " 7" " 0 " " " 9" 2 29" 0 " 0 " " 7" 9" " 8 0 " 0 " " " " " 2 " 8 0 " 0 " " " " " " 7" 9" "

20 SWP - 0 SINGLE WEAR PAD. " TYP. * Temperature Range : -25 Degree * Exposted Polyurethane Surface are coated with * (-25 Degrees C ) to Degrees F (5 Degrees C) Monolar Mastic. * Light or Medium Load Capacity * Support Saddles are constructed in accordance * Design Load are Based on a Safety Factor of 5 with the MSS - SP58 and the ASME B Piping * Support Saddle are constructed on High Density * Technical Specification: AAAT - CS * Support Saddle restrains - Y movement. "F" 5 5 /" 2 " 5 55 /" 2 " " 2 " " 0" " " " " LIGHT PAD THK. /" /" /" /" /" /" /" /" /" /" /" /" /" /" /" /" / / / 2 " " " / " " " " " 5 THICKNESS - / 2 " " 8 2- / 2 " 8 " 8 - / 2 " " 8 " 8 " 8 " 8 " " " " " " 7" 9" " " " 7" " 0 " " " 9" 2 29" 0 " 0 " " 7" 9" " 8 0 " 0 " " " " " 2 " 8 0 " 0 " " " " " " 7" 9" "

21 DWP - 0 DOUBLE WEAR PAD " TYP. "F" * Temperature Range : -25 Degree * Exposted Polyurethane Surface are coated with * (-25 Degrees C ) to Degrees F (5 Degrees C) Monolar Mastic. * Light or Medium Load Capacity * Support Saddles are constructed in accordance * Design Load are Based on a Safety Factor of 5 with the MSS - SP58 and the ASME B Piping * Support Saddle are constructed on High Density * Technical Specification: AAAT - CS * Support Saddle restrains - Y movement. 5 5 /" 2 " 5 55 /" 2 " " 2 " " 0" " " " " LIGHT PAD THK. /" /" /" /" /" /" /" /" /" /" /" /" /" /" /" /" / / / 2 " " " / " " " " " 5 THICKNESS - / 2 " " 8 2- / 2 " 8 " 8 - / 2 " " 8 " 8 " 8 " 8 " " " " " " 7" 9" " " " 7" " 0 " " " 9" 2 29" 0 " 0 " " 7" 9" " 8 0 " 0 " " " " " 2 " 8 0 " 0 " " " " " " 7" 9" "

22 SWP - 80MS SINGLE WEAR PAD BOP TYP. " TYP. "F" METAL SHIELD * Temperature Range : -25 Degree * Exposted Polyurethane Surface are coated with * (-25 Degrees C ) to Degrees F (5 Degrees C) Monolar Mastic. * Design Load are Based on a Safety Factor of 5 with the MSS - SP58 and the ASME B Piping * Support Saddle are constructed on High Density * Technical Specification: AAAT - CS * Support Saddle restrains - Y movement. * Steel Component are constructed of A - Steel 5 5 /" 2 " 5 55 /" 2 " " 2 " " 0" " " " " HEAVY PAD THK. /" /" /" /" /" /" /" /" /" /" /" /" /" /" /" /" / / / 2 " " " / " " " " " 5 THICKNESS - / 2 " " 8 2- / 2 " 8 " 8 - / 2 " " 8 " 8 " 8 " 8 " " " " " " 7" 9" " " " 7" " 0 " " " 9" 2 29" 0 " 0 " " 7" 9" " 8 0 " 0 " " " " " 2 " 8 0 " 0 " " " " " " 7" 9" " 9

23 DWP - 80MS BOP DOUBLE WEAR PAD TYP. " TYP. "F" METAL SHIELD * Temperature Range : -25 Degree * Exposted Polyurethane Surface are coated with * (-25 Degrees C ) to Degrees F (5 Degrees C) Monolar Mastic. * Design Load are Based on a Safety Factor of 5 with the MSS - SP58 and the ASME B Piping * Support Saddle are constructed on High Density * Technical Specification: AAAT - CS * Support Saddle restrains - Y movement. * Steel Component are constructed of A - Steel PAD THK. 5 5 /" 2 " 5 55 /" 2 " " 2 " " 0" " " " " HEAVY /" /" /" /" /" /" /" /" /" /" /" /" /" /" /" /" / / / 2 " " " / " " " " " 5 THICKNESS - / 2 " " 8 2- / 2 " 8 " 8 - / 2 " " 8 " 8 " 8 " 8 " " " " " " 7" 9" " " " 7" " 0 " " " 9" 2 29" 0 " 0 " " 7" 9" " 8 0 " 0 " " " " " 2 " 8 0 " 0 " " " " " " 7" 9" " 20

24 SWP - 0BC A-07 OR B7 BOLT/ STUDS BOP SINGLE WEAR PAD TYP. " TYP. "F" * Temperature Range : -25 Degree * Exposted Polyurethane Surface are coated with * (-25 Degrees C ) to Degrees F (5 Degrees C) Monolar Mastic. * Design Load are Based on a Safety Factor of 5 with the MSS - SP58 and the ASME B Piping * Support Saddle are constructed on High Density * Technical Specification: AAAT - CS * Support Saddle restrains - Y movement. * Steel Component are constructed of A - Steel 5 5 /" 2 " 5 55 /" 2 " " 2 " " 0" " " " " HEAVY PAD THK. /" /" /" /" /" /" /" /" /" /" /" /" /" /" /" /" / / / 2 " " " / " " " " " 5 THICKNESS - / 2 " " 8 2- / 2 " 8 " 8 - / 2 " " 8 " 8 " 8 " 8 " " " " " " 7" 9" " " " 7" " 0 " " " 9" 2 29" 0 " 0 " " 7" 9" " 8 0 " 0 " " " " " 2 " 8 0 " 0 " " " " " " 7" 9" " 2

25 DWP - 0BC A-07 OR B7 BOLT/ STUDS BOP DOUBLE WEAR PAD TYP. " TYP. "F" * Temperature Range : -25 Degree * Exposted Polyurethane Surface are coated with * (-25 Degrees C ) to Degrees F (5 Degrees C) Monolar Mastic. * Design Load are Based on a Safety Factor of 5 with the MSS - SP58 and the ASME B Piping * Support Saddle are constructed on High Density * Technical Specification: AAAT - CS * Support Saddle restrains - Y movement. * Steel Component are constructed of A - Steel 5 5 /" 2 " 5 55 /" 2 " " 2 " " 0" " " " " HEAVY PAD THK. /" /" /" /" /" /" /" /" /" /" /" /" /" /" /" /" / / / 2 " " " / " " " " " 5 THICKNESS - / 2 " " 8 2- / 2 " 8 " 8 - / 2 " " 8 " 8 " 8 " 8 " " " " " " 7" 9" " " " 7" " 0 " " " 9" 2 29" 0 " 0 " " 7" 9" " 8 0 " 0 " " " " " 2 " 8 0 " 0 " " " " " " 7" 9" "

26 SWP - 80MS - FB SINGLE WEAR PAD TYP. " TYP. METAL SHIELD "F" * Temperature Range : -25 Degree * Exposted Polyurethane Surface are coated with * (-25 Degrees C ) to Degrees F (5 Degrees C) Monolar Mastic. * Design Load are Based on a Safety Factor of 5 with the MSS - SP58 and the ASME B Piping * Support Saddle are constructed on High Density * Technical Specification: AAAT - CS * Support Saddle restrains - Y movement. * Steel Component are constructed of A - Steel 5 5 /" 2 " 5 55 /" 2 " " 2 " " 0" " " " " HEAVY PAD THK. /" /" /" /" /" /" /" /" /" /" /" /" /" /" /" /" / / / 2 " " " / " " " " " 5 THICKNESS - / 2 " " 8 2- / 2 " 8 " 8 - / 2 " " 8 " 8 " 8 " 8 " " " " " " 7" 9" " " " 7" " 0 " " " 9" 2 29" 0 " 0 " " 7" 9" " 8 0 " 0 " " " " " 2 " 8 0 " 0 " " " " " " 7" 9" " 2

27 DWP - 80MS - FB A-07 OR B7 BOLT/ STUDS BOP SINGLE WEAR PAD TYP. " TYP. "F" * Temperature Range : -25 Degree * Exposted Polyurethane Surface are coated with * (-25 Degrees C ) to Degrees F (5 Degrees C) Monolar Mastic. * Design Load are Based on a Safety Factor of 5 with the MSS - SP58 and the ASME B Piping * Support Saddle are constructed on High Density * Technical Specification: AAAT - CS * Support Saddle restrains - Y movement. * Steel Component are constructed of A - Steel 5 5 /" 2 " 5 55 /" 2 " " 2 " " 0" " " " " HEAVY PAD THK. /" /" /" /" /" /" /" /" /" /" /" /" /" /" /" /" / / / 2 " " " / " " " " " 5 THICKNESS - / 2 " " 8 2- / 2 " 8 " 8 - / 2 " " 8 " 8 " 8 " 8 " " " " " " 7" 9" " " " 7" " 0 " " " 9" 2 29" 0 " 0 " " 7" 9" " 8 0 " 0 " " " " " 2 " 8 0 " 0 " " " " " " 7" 9" "

28 SWP - 0BC - FB A-07 OR B7 BOLT/ STUDS BOP SINGLE WEAR PAD TYP. " TYP. "F" * Temperature Range : -25 Degree * Exposted Polyurethane Surface are coated with * (-25 Degrees C ) to Degrees F (5 Degrees C) Monolar Mastic. * Design Load are Based on a Safety Factor of 5 with the MSS - SP58 and the ASME B Piping * Support Saddle are constructed on High Density * Technical Specification: AAAT - CS * Support Saddle restrains - Y movement. * Steel Component are constructed of A - Steel 5 5 /" 2 " 5 55 /" 2 " " 2 " " 0" " " " " HEAVY PAD THK. /" /" /" /" /" /" /" /" /" /" /" /" /" /" /" /" / / / 2 " " " / " " " " " 5 THICKNESS - / 2 " " 8 2- / 2 " 8 " 8 - / 2 " " 8 " 8 " 8 " 8 " " " " " " 7" 9" " " " 7" " 0 " " " 9" 2 29" 0 " 0 " " 7" 9" " 8 0 " 0 " " " " " 2 " 8 0 " 0 " " " " " " 7" 9" " 25

29 DWP - 0BC - FB A-07 OR B7 BOLT/ STUDS BOP DOUBLE WEAR PAD TYP. " TYP. "F" * Temperature Range : -25 Degree * Exposted Polyurethane Surface are coated with * (-25 Degrees C ) to Degrees F (5 Degrees C) Monolar Mastic. * Design Load are Based on a Safety Factor of 5 with the MSS - SP58 and the ASME B Piping * Support Saddle are constructed on High Density * Technical Specification: AAAT - CS * Support Saddle restrains - Y movement. * Steel Component are constructed of A - Steel 5 5 /" 2 " 5 55 /" 2 " " 2 " " 0" " " " " HEAVY PAD THK. /" /" /" /" /" /" /" /" /" /" /" /" /" /" /" /" / / / 2 " " " / " " " " " 5 THICKNESS - / 2 " " 8 2- / 2 " 8 " 8 - / 2 " " 8 " 8 " 8 " 8 " " " " " " 7" 9" " " " 7" " 0 " " " 9" 2 29" 0 " 0 " " 7" 9" " 8 0 " 0 " " " " " 2 " 8 0 " 0 " " " " " " 7" 9" " 2

30 SWP - 0BC - DW A-07 OR B7 BOLT/ STUDS BOP SINGLE WEAR PAD TYP. " TYP. " " * Temperature Range : -25 Degree * Exposted Polyurethane Surface are coated with * (-25 Degrees C ) to Degrees F (5 Degrees C) Monolar Mastic. * Design Load are Based on a Safety Factor of 5 with the MSS - SP58 and the ASME B Piping * Support Saddle are constructed on High Density * Technical Specification: AAAT - CS * Support Saddle restrains - Y movement. * Steel Component are constructed of A - Steel 2 " " 0" " " " " " HEAVY THICKNESS " - / 2 " 2 " 2- / 2 " " " 5 " " 7 " 8 " BOP BOP BOP BOP BOP BOP BOP BOP BOP BOP " " " 5 " 7 " 8 " 9 " " 5 " 0" 7 " 0" 9 " " 5 " " 7 " 8 " 9 " 0 " " " 0" 8 " 0" 20 " " " " 7 " 8 " 9 " 0 " " " 0" 8 " 0" 20 " " 7 " 8 " 9 " 0 " " " 5 " 7 " 0" 9 " 0" 2 " " 7 " 8 " 9 " 0 " " " 5 " 7 " 0" 9 " 0" 2 " " 8 " 9 " 0 " " " " " " 8 " 0" 20 " 0" " " 9 " 0 " " " " " 5 " 7 " 9 " 0" 2 " 0" 2 " " " " " " " " 5 " " 7 " 9 " 2 " 0" 2 " 0" 25 " " " " " 5 " " " " 7 " " 9 " 2 " 2 " 0" 25 " 0" 27 " " 5 " " " " 7 " " 8 " " 9 " " 2 " 2 " 25 " 0" 27 " 0" 29 " " 7 " 8 " 9 " 20 " " " 29 0" " 9 " 20 " " 2 " " 29 0" " " " 2 " 2 " " " 0" " 5 " 2 " " 25 " " " 0" 5 " 7 " 27 " 28 " 29 " 0 " 5 0" 7 0" 9 " " 29 " 0 " " " 5 7 0" 9 0" " " " " " " " " 0" " 5 " " " 5 " " 7 9 " 0" 0" 5 " 7 " 5 " " 7 " 8 " 9 " 0" 5 0" 7 " 9 " 7 " 8 " 9 " 0 " " 5 0" 7 0" 9 " " 9 " 0 " " " " 5 7 0" 9 0" " 5 " 7 " 7 " 5 7 " 7 " " 5 7 0" 55 7 " 57 7 " 5 7 " 7 " 7 7 " 8 7 " " " 57 7 "

31 DWP - 0BC - DW A-07 OR B7 BOLT/ STUDS BOP DOUBLE WEAR PAD TYP. " TYP. " " * Temperature Range : -25 Degree * Exposted Polyurethane Surface are coated with * (-25 Degrees C ) to Degrees F (5 Degrees C) Monolar Mastic. * Design Load are Based on a Safety Factor of 5 with the MSS - SP58 and the ASME B Piping * Support Saddle are constructed on High Density * Technical Specification: AAAT - CS * Support Saddle restrains - Y movement. * Steel Component are constructed of A - Steel 2 " " 0" " " " " " HEAVY THICKNESS " - / 2 " 2 " 2- / 2 " " " BOP BOP BOP BOP BOP BOP BOP BOP BOP BOP " " " 5 " 7 " 8 " 9 " " 5 " 0" 7 " 0" 9 " " 5 " " 7 " 8 " 9 " 0 " " " 0" 8 " 0" 20 " " " " 7 " 8 " 9 " 0 " " " 0" 8 " 0" 20 " " 7 " 8 " 9 " 0 " " " 5 " 7 " 0" 9 " 0" 2 " " 7 " 8 " 9 " 0 " " " 5 " 7 " 0" 9 " 0" 2 " " 8 " 9 " 0 " " " " " " 8 " 0" 20 " 0" " " 9 " 0 " " " " " 5 " 7 " 9 " 0" 2 " 0" 2 " " " " " " " " 5 " " 7 " 9 " 2 " 0" 2 " 0" 25 " " " " " 5 " " " " 7 " " 9 " 2 " 2 " 0" 25 " 0" 27 " " 5 " " " " 7 " " 8 " " 9 " " 2 " 2 " 25 " 0" 27 " 0" 29 " " 7 " 8 " 9 " 20 " " " 29 0" " 9 " 20 " " 2 " " 29 0" " " " 2 " 2 " " " 0" " 5 " 2 " " 25 " " " 0" 5 " 7 " 27 " 28 " 29 " 0 " 5 0" 7 0" 9 " " 29 " 0 " " " 5 7 0" 9 0" " " " " " " " " 0" " 5 " " " 5 " " 7 9 " 0" 0" 5 " 7 " 5 " " 7 " 8 " 9 " 0" 5 0" 7 " 9 " 7 " 8 " 9 " 0 " " 5 0" 7 0" 9 " " 9 " 0 " " " " 5 7 0" 9 0" " 5 " 7 " 7 " 5 7 " 7 " " 5 7 0" 55 7 " 57 7 " 5 7 " 7 " 7 7 " 8 7 " " " 57 7 " " " 7 " 8 "

32 SWP - 0BC - DW - GC A-07 OR B7 BOLT/ STUDS BOP SINGLE WEAR PAD TYP. " TYP. " " * Temperature Range : -25 Degree * Exposted Polyurethane Surface are coated with * (-25 Degrees C ) to Degrees F (5 Degrees C) Monolar Mastic. * Design Load are Based on a Safety Factor of 5 with the MSS - SP58 and the ASME B Piping * Support Saddle are constructed on High Density * Technical Specification: AAAT - CS * Support Saddle restrains - Y movement. * Steel Component are constructed of A - Steel 2 " " 0" " " " " " HEAVY THICKNESS " - / 2 " 2 " 2- / 2 " " " 5 " " 7 " 8 " BOP BOP BOP BOP BOP BOP BOP BOP BOP BOP " " " 5 " 7 " 8 " 9 " " 5 " 0" 7 " 0" 9 " " 5 " " 7 " 8 " 9 " 0 " " " 0" 8 " 0" 20 " " " " 7 " 8 " 9 " 0 " " " 0" 8 " 0" 20 " " 7 " 8 " 9 " 0 " " " 5 " 7 " 0" 9 " 0" 2 " " 7 " 8 " 9 " 0 " " " 5 " 7 " 0" 9 " 0" 2 " " 8 " 9 " 0 " " " " " " 8 " 0" 20 " 0" " " 9 " 0 " " " " " 5 " 7 " 9 " 0" 2 " 0" 2 " " " " " " " " 5 " " 7 " 9 " 2 " 0" 2 " 0" 25 " " " " " 5 " " " " 7 " " 9 " 2 " 2 " 0" 25 " 0" 27 " " 5 " " " " 7 " " 8 " " 9 " " 2 " 2 " 25 " 0" 27 " 0" 29 " " 7 " 8 " 9 " 20 " " " 29 0" " 9 " 20 " " 2 " " 29 0" " " " 2 " 2 " " " 0" " 5 " 2 " " 25 " " " 0" 5 " 7 " 27 " 28 " 29 " 0 " 5 0" 7 0" 9 " " 29 " 0 " " " 5 7 0" 9 0" " " " " " " " " 0" " 5 " " " 5 " " 7 9 " 0" 0" 5 " 7 " 5 " " 7 " 8 " 9 " 0" 5 0" 7 " 9 " 7 " 8 " 9 " 0 " " 5 0" 7 0" 9 " " 9 " 0 " " " " 5 7 0" 9 0" " 5 " 7 " 7 " 5 7 " 7 " " 5 7 0" 55 7 " 57 7 " 5 7 " 7 " 7 7 " 8 7 " " " 57 7 "

33 DWP - 0BC - DW - GC A-07 OR B7 BOLT/ STUDS BOP DOUBLE WEAR PAD TYP. " TYP. " " * Temperature Range : -25 Degree * Exposted Polyurethane Surface are coated with * (-25 Degrees C ) to Degrees F (5 Degrees C) Monolar Mastic. * Design Load are Based on a Safety Factor of 5 with the MSS - SP58 and the ASME B Piping * Support Saddle are constructed on High Density * Technical Specification: AAAT - CS * Support Saddle restrains - Y movement. * Steel Component are constructed of A - Steel 2 " " 0" " " " " " HEAVY THICKNESS " - / 2 " 2 " 2- / 2 " " " 5 " " 7 " 8 " BOP BOP BOP BOP BOP BOP BOP BOP BOP BOP " " " 5 " 7 " 8 " 9 " " 5 " 0" 7 " 0" 9 " " 5 " " 7 " 8 " 9 " 0 " " " 0" 8 " 0" 20 " " " " 7 " 8 " 9 " 0 " " " 0" 8 " 0" 20 " " 7 " 8 " 9 " 0 " " " 5 " 7 " 0" 9 " 0" 2 " " 7 " 8 " 9 " 0 " " " 5 " 7 " 0" 9 " 0" 2 " " 8 " 9 " 0 " " " " " " 8 " 0" 20 " 0" " " 9 " 0 " " " " " 5 " 7 " 9 " 0" 2 " 0" 2 " " " " " " " " 5 " " 7 " 9 " 2 " 0" 2 " 0" 25 " " " " " 5 " " " " 7 " " 9 " 2 " 2 " 0" 25 " 0" 27 " " 5 " " " " 7 " " 8 " " 9 " " 2 " 2 " 25 " 0" 27 " 0" 29 " " 7 " 8 " 9 " 20 " " " 29 0" " 9 " 20 " " 2 " " 29 0" " " " 2 " 2 " " " 0" " 5 " 2 " " 25 " " " 0" 5 " 7 " 27 " 28 " 29 " 0 " 5 0" 7 0" 9 " " 29 " 0 " " " 5 7 0" 9 0" " " " " " " " " 0" " 5 " " " 5 " " 7 9 " 0" 0" 5 " 7 " 5 " " 7 " 8 " 9 " 0" 5 0" 7 " 9 " 7 " 8 " 9 " 0 " " 5 0" 7 0" 9 " " 9 " 0 " " " " 5 7 0" 9 0" " 5 " 7 " 7 " 5 7 " 7 " " 5 7 0" 55 7 " 57 7 " 5 7 " 7 " 7 7 " 8 7 " " " 57 7 "

34 SWP - 0BC - DW - BG A-07 OR B7 BOLT/ STUDS BOP TYP. SINGLE WEAR PAD " TYP. " " * Temperature Range : -25 Degree * Exposted Polyurethane Surface are coated with * (-25 Degrees C ) to Degrees F (5 Degrees C) Monolar Mastic. * Design Load are Based on a Safety Factor of 5 with the MSS - SP58 and the ASME B Piping * Support Saddle are constructed on High Density * Technical Specification: AAAT - CS * Support Saddle restrains - Y movement. * Steel Component are constructed of A - Steel 2 " " 0" " " " " " HEAVY THICKNESS " - / 2 " 2 " 2- / 2 " " " 5 " " 7 " 8 " BOP BOP BOP BOP BOP BOP BOP BOP BOP BOP " " " 5 " 7 " 8 " 9 " " 5 " 0" 7 " 0" 9 " " 5 " " 7 " 8 " 9 " 0 " " " 0" 8 " 0" 20 " " " " 7 " 8 " 9 " 0 " " " 0" 8 " 0" 20 " " 7 " 8 " 9 " 0 " " " 5 " 7 " 0" 9 " 0" 2 " " 7 " 8 " 9 " 0 " " " 5 " 7 " 0" 9 " 0" 2 " " 8 " 9 " 0 " " " " " " 8 " 0" 20 " 0" " " 9 " 0 " " " " " 5 " 7 " 9 " 0" 2 " 0" 2 " " " " " " " " 5 " " 7 " 9 " 2 " 0" 2 " 0" 25 " " " " " 5 " " " " 7 " " 9 " 2 " 2 " 0" 25 " 0" 27 " " 5 " " " " 7 " " 8 " " 9 " " 2 " 2 " 25 " 0" 27 " 0" 29 " " 7 " 8 " 9 " 20 " " " 29 0" " 9 " 20 " " 2 " " 29 0" " " " 2 " 2 " " " 0" " 5 " 2 " " 25 " " " 0" 5 " 7 " 27 " 28 " 29 " 0 " 5 0" 7 0" 9 " " 29 " 0 " " " 5 7 0" 9 0" " " " " " " " " 0" " 5 " " " 5 " " 7 9 " 0" 0" 5 " 7 " 5 " " 7 " 8 " 9 " 0" 5 0" 7 " 9 " 7 " 8 " 9 " 0 " " 5 0" 7 0" 9 " " 9 " 0 " " " " 5 7 0" 9 0" " 5 " 7 " 7 " 5 7 " 7 " " 5 7 0" 55 7 " 57 7 " 5 7 " 7 " 7 7 " 8 7 " " " 57 7 " 59 7

35 DWP - 0BC - DW - BG A-07 OR B7 BOLT/ STUDS BOP TYP. DOUBLE WEAR PAD * Temperature Range : -25 Degree * Exposted Polyurethane Surface are coated with * (-25 Degrees C ) to Degrees F (5 Degrees C) Monolar Mastic. * Design Load are Based on a Safety Factor of 5 with the MSS - SP58 and the ASME B Piping * Support Saddle are constructed on High Density * Technical Specification: AAAT - CS * Support Saddle restrains - Y movement. * Steel Component are constructed of A - Steel " TYP. " " 2 " " 0" " " " " " HEAVY THICKNESS " - / 2 " 2 " 2- / 2 " " " 5 " " 7 " 8 " BOP BOP BOP BOP BOP BOP BOP BOP BOP BOP " " " 5 " 7 " 8 " 9 " " 5 " 0" 7 " 0" 9 " " 5 " " 7 " 8 " 9 " 0 " " " 0" 8 " 0" 20 " " " " 7 " 8 " 9 " 0 " " " 0" 8 " 0" 20 " " 7 " 8 " 9 " 0 " " " 5 " 7 " 0" 9 " 0" 2 " " 7 " 8 " 9 " 0 " " " 5 " 7 " 0" 9 " 0" 2 " " 8 " 9 " 0 " " " " " " 8 " 0" 20 " 0" " " 9 " 0 " " " " " 5 " 7 " 9 " 0" 2 " 0" 2 " " " " " " " " 5 " " 7 " 9 " 2 " 0" 2 " 0" 25 " " " " " 5 " " " " 7 " " 9 " 2 " 2 " 0" 25 " 0" 27 " " 5 " " " " 7 " " 8 " " 9 " " 2 " 2 " 25 " 0" 27 " 0" 29 " " 7 " 8 " 9 " 20 " " " 29 0" " 9 " 20 " " 2 " " 29 0" " " " 2 " 2 " " " 0" " 5 " 2 " " 25 " " " 0" 5 " 7 " 27 " 28 " 29 " 0 " 5 0" 7 0" 9 " " 29 " 0 " " " 5 7 0" 9 0" " " " " " " " " 0" " 5 " " " 5 " " 7 9 " 0" 0" 5 " 7 " 5 " " 7 " 8 " 9 " 0" 5 0" 7 " 9 " 7 " 8 " 9 " 0 " " 5 0" 7 0" 9 " " 9 " 0 " " " " 5 7 0" 9 0" " 5 " 7 " 7 " 5 7 " 7 " " 5 7 0" 55 7 " 57 7 " 5 7 " 7 " 7 7 " 8 7 " " " 57 7 "

36 SWP - 0BC - DW - AG A-07 OR B7 BOLT/ STUDS BOP SINGLE WEAR PAD TYP. " " * Temperature Range : -25 Degree * Exposted Polyurethane Surface are coated with * (-25 Degrees C ) to Degrees F (5 Degrees C) Monolar Mastic. * Design Load are Based on a Safety Factor of 5 with the MSS - SP58 and the ASME B Piping * Support Saddle are constructed on High Density * Technical Specification: AAAT - CS * Support Saddle restrains - Y movement. * Steel Component are constructed of A - Steel " TYP. 2 " " 0" " " " " " HEAVY THICKNESS " - / 2 " 2 " 2- / 2 " " " 5 " " 7 " 8 " BOP BOP BOP BOP BOP BOP BOP BOP BOP BOP " " " 5 " 7 " 8 " 9 " " 5 " 0" 7 " 0" 9 " " 5 " " 7 " 8 " 9 " 0 " " " 0" 8 " 0" 20 " " " " 7 " 8 " 9 " 0 " " " 0" 8 " 0" 20 " " 7 " 8 " 9 " 0 " " " 5 " 7 " 0" 9 " 0" 2 " " 7 " 8 " 9 " 0 " " " 5 " 7 " 0" 9 " 0" 2 " " 8 " 9 " 0 " " " " " " 8 " 0" 20 " 0" " " 9 " 0 " " " " " 5 " 7 " 9 " 0" 2 " 0" 2 " " " " " " " " 5 " " 7 " 9 " 2 " 0" 2 " 0" 25 " " " " " 5 " " " " 7 " " 9 " 2 " 2 " 0" 25 " 0" 27 " " 5 " " " " 7 " " 8 " " 9 " " 2 " 2 " 25 " 0" 27 " 0" 29 " " 7 " 8 " 9 " 20 " " " 29 0" " 9 " 20 " " 2 " " 29 0" " " " 2 " 2 " " " 0" " 5 " 2 " " 25 " " " 0" 5 " 7 " 27 " 28 " 29 " 0 " 5 0" 7 0" 9 " " 29 " 0 " " " 5 7 0" 9 0" " " " " " " " " 0" " 5 " " " 5 " " 7 9 " 0" 0" 5 " 7 " 5 " " 7 " 8 " 9 " 0" 5 0" 7 " 9 " 7 " 8 " 9 " 0 " " 5 0" 7 0" 9 " " 9 " 0 " " " " 5 7 0" 9 0" " 5 " 7 " 7 " 5 7 " 7 " " 5 7 0" 55 7 " 57 7 " 5 7 " 7 " 7 7 " 8 7 " " " 57 7 " 59 7

37 DWP - 0BC - DW - AG A-07 OR B7 BOLT/ STUDS BOP DOUBLE WEAR PAD TYP. " TYP. " " * Temperature Range : -25 Degree * Exposted Polyurethane Surface are coated with * (-25 Degrees C ) to Degrees F (5 Degrees C) Monolar Mastic. * Design Load are Based on a Safety Factor of 5 with the MSS - SP58 and the ASME B Piping * Support Saddle are constructed on High Density * Technical Specification: AAAT - CS * Support Saddle restrains - Y movement. * Steel Component are constructed of A - Steel 2 " " 0" " " " " " HEAVY THICKNESS " - / 2 " 2 " 2- / 2 " " " 5 " " 7 " 8 " BOP BOP BOP BOP BOP BOP BOP BOP BOP BOP " " " 5 " 7 " 8 " 9 " " 5 " 0" 7 " 0" 9 " " 5 " " 7 " 8 " 9 " 0 " " " 0" 8 " 0" 20 " " " " 7 " 8 " 9 " 0 " " " 0" 8 " 0" 20 " " 7 " 8 " 9 " 0 " " " 5 " 7 " 0" 9 " 0" 2 " " 7 " 8 " 9 " 0 " " " 5 " 7 " 0" 9 " 0" 2 " " 8 " 9 " 0 " " " " " " 8 " 0" 20 " 0" " " 9 " 0 " " " " " 5 " 7 " 9 " 0" 2 " 0" 2 " " " " " " " " 5 " " 7 " 9 " 2 " 0" 2 " 0" 25 " " " " " 5 " " " " 7 " " 9 " 2 " 2 " 0" 25 " 0" 27 " " 5 " " " " 7 " " 8 " " 9 " " 2 " 2 " 25 " 0" 27 " 0" 29 " " 7 " 8 " 9 " 20 " " " 29 0" " 9 " 20 " " 2 " " 29 0" " " " 2 " 2 " " " 0" " 5 " 2 " " 25 " " " 0" 5 " 7 " 27 " 28 " 29 " 0 " 5 0" 7 0" 9 " " 29 " 0 " " " 5 7 0" 9 0" " " " " " " " " 0" " 5 " " " 5 " " 7 9 " 0" 0" 5 " 7 " 5 " " 7 " 8 " 9 " 0" 5 0" 7 " 9 " 7 " 8 " 9 " 0 " " 5 0" 7 0" 9 " " 9 " 0 " " " " 5 7 0" 9 0" " 5 " 7 " 7 " 5 7 " 7 " " 5 7 0" 55 7 " 57 7 " 5 7 " 7 " 7 7 " 8 7 " " " 57 7 " 59 7

38 SWP - 0BC - DW - ST A-07 OR B7 BOLT/ STUDS BOP SINGLE WEAR PAD TYP. " TYP. " " * Temperature Range : -25 Degree * Exposted Polyurethane Surface are coated with * (-25 Degrees C ) to Degrees F (5 Degrees C) Monolar Mastic. * Design Load are Based on a Safety Factor of 5 with the MSS - SP58 and the ASME B Piping * Support Saddle are constructed on High Density * Technical Specification: AAAT - CS * Support Saddle restrains - Y movement. * Steel Component are constructed of A - Steel 2 " " 0" " " " " " HEAVY THICKNESS " - / 2 " 2 " 2- / 2 " " " 5 " " 7 " 8 " BOP BOP BOP BOP BOP BOP BOP BOP BOP BOP " " " 5 " 7 " 8 " 9 " " 5 " 0" 7 " 0" 9 " " 5 " " 7 " 8 " 9 " 0 " " " 0" 8 " 0" 20 " " " " 7 " 8 " 9 " 0 " " " 0" 8 " 0" 20 " " 7 " 8 " 9 " 0 " " " 5 " 7 " 0" 9 " 0" 2 " " 7 " 8 " 9 " 0 " " " 5 " 7 " 0" 9 " 0" 2 " " 8 " 9 " 0 " " " " " " 8 " 0" 20 " 0" " " 9 " 0 " " " " " 5 " 7 " 9 " 0" 2 " 0" 2 " " " " " " " " 5 " " 7 " 9 " 2 " 0" 2 " 0" 25 " " " " " 5 " " " " 7 " " 9 " 2 " 2 " 0" 25 " 0" 27 " " 5 " " " " 7 " " 8 " " 9 " " 2 " 2 " 25 " 0" 27 " 0" 29 " " 7 " 8 " 9 " 20 " " " 29 0" " 9 " 20 " " 2 " " 29 0" " " " 2 " 2 " " " 0" " 5 " 2 " " 25 " " " 0" 5 " 7 " 27 " 28 " 29 " 0 " 5 0" 7 0" 9 " " 29 " 0 " " " 5 7 0" 9 0" " " " " " " " " 0" " 5 " " " 5 " " 7 9 " 0" 0" 5 " 7 " 5 " " 7 " 8 " 9 " 0" 5 0" 7 " 9 " 7 " 8 " 9 " 0 " " 5 0" 7 0" 9 " " 9 " 0 " " " " 5 7 0" 9 0" " 5 " 7 " 7 " 5 7 " 7 " " 5 7 0" 55 7 " 57 7 " 5 7 " 7 " 7 7 " 8 7 " " " 57 7 "

39 DWP - 0BC - DW - ST A-07 OR B7 BOLT/ STUDS BOP DOUBLE WEAR PAD TYP. " TYP. " " * Temperature Range : -25 Degree * Exposted Polyurethane Surface are coated with * (-25 Degrees C ) to Degrees F (5 Degrees C) Monolar Mastic. * Design Load are Based on a Safety Factor of 5 with the MSS - SP58 and the ASME B Piping * Support Saddle are constructed on High Density * Technical Specification: AAAT - CS * Support Saddle restrains - Y movement. * Steel Component are constructed of A - Steel 2 " " 0" " " " " " HEAVY THICKNESS " - / 2 " 2 " 2- / 2 " " " 5 " " 7 " 8 " BOP BOP BOP BOP BOP BOP BOP BOP BOP BOP " " " 5 " 7 " 8 " 9 " " 5 " 0" 7 " 0" 9 " " 5 " " 7 " 8 " 9 " 0 " " " 0" 8 " 0" 20 " " " " 7 " 8 " 9 " 0 " " " 0" 8 " 0" 20 " " 7 " 8 " 9 " 0 " " " 5 " 7 " 0" 9 " 0" 2 " " 7 " 8 " 9 " 0 " " " 5 " 7 " 0" 9 " 0" 2 " " 8 " 9 " 0 " " " " " " 8 " 0" 20 " 0" " " 9 " 0 " " " " " 5 " 7 " 9 " 0" 2 " 0" 2 " " " " " " " " 5 " " 7 " 9 " 2 " 0" 2 " 0" 25 " " " " " 5 " " " " 7 " " 9 " 2 " 2 " 0" 25 " 0" 27 " " 5 " " " " 7 " " 8 " " 9 " " 2 " 2 " 25 " 0" 27 " 0" 29 " " 7 " 8 " 9 " 20 " " " 29 0" " 9 " 20 " " 2 " " 29 0" " " " 2 " 2 " " " 0" " 5 " 2 " " 25 " " " 0" 5 " 7 " 27 " 28 " 29 " 0 " 5 0" 7 0" 9 " " 29 " 0 " " " 5 7 0" 9 0" " " " " " " " " 0" " 5 " " " 5 " " 7 9 " 0" 0" 5 " 7 " 5 " " 7 " 8 " 9 " 0" 5 0" 7 " 9 " 7 " 8 " 9 " 0 " " 5 0" 7 0" 9 " " 9 " 0 " " " " 5 7 0" 9 0" " 5 " 7 " 7 " 5 7 " 7 " " 5 7 0" 55 7 " 57 7 " 5 7 " 7 " 7 7 " 8 7 " " " 57 7 " 59 7

40 SWP - 0BC - DW - AG & ST A-07 OR B7 BOLT/ STUDS BOP SINGLE WEAR PAD TYP. " TYP. " " * Temperature Range : -25 Degree * Exposted Polyurethane Surface are coated with * (-25 Degrees C ) to Degrees F (5 Degrees C) Monolar Mastic. * Design Load are Based on a Safety Factor of 5 with the MSS - SP58 and the ASME B Piping * Support Saddle are constructed on High Density * Technical Specification: AAAT - CS * Support Saddle restrains - Y movement. * Steel Component are constructed of A - Steel 2 " " 0" " " " " " HEAVY THICKNESS " - / 2 " 2 " 2- / 2 " " " 5 " " 7 " 8 " BOP BOP BOP BOP BOP BOP BOP BOP BOP BOP " " " 5 " 7 " 8 " 9 " " 5 " 0" 7 " 0" 9 " " 5 " " 7 " 8 " 9 " 0 " " " 0" 8 " 0" 20 " " " " 7 " 8 " 9 " 0 " " " 0" 8 " 0" 20 " " 7 " 8 " 9 " 0 " " " 5 " 7 " 0" 9 " 0" 2 " " 7 " 8 " 9 " 0 " " " 5 " 7 " 0" 9 " 0" 2 " " 8 " 9 " 0 " " " " " " 8 " 0" 20 " 0" " " 9 " 0 " " " " " 5 " 7 " 9 " 0" 2 " 0" 2 " " " " " " " " 5 " " 7 " 9 " 2 " 0" 2 " 0" 25 " " " " " 5 " " " " 7 " " 9 " 2 " 2 " 0" 25 " 0" 27 " " 5 " " " " 7 " " 8 " " 9 " " 2 " 2 " 25 " 0" 27 " 0" 29 " " 7 " 8 " 9 " 20 " " " 29 0" " 9 " 20 " " 2 " " 29 0" " " " 2 " 2 " " " 0" " 5 " 2 " " 25 " " " 0" 5 " 7 " 27 " 28 " 29 " 0 " 5 0" 7 0" 9 " " 29 " 0 " " " 5 7 0" 9 0" " " " " " " " " 0" " 5 " " " 5 " " 7 9 " 0" 0" 5 " 7 " 5 " " 7 " 8 " 9 " 0" 5 0" 7 " 9 " 7 " 8 " 9 " 0 " " 5 0" 7 0" 9 " " 9 " 0 " " " " 5 7 0" 9 0" " 5 " 7 " 7 " 5 7 " 7 " " 5 7 0" 55 7 " 57 7 " 5 7 " 7 " 7 7 " 8 7 " " " 57 7 "

41 DWP - 0BC - DW - AG & ST A-07 OR B7 BOLT/ STUDS BOP DOUBLE WEAR PAD TYP. " TYP. " " * Temperature Range : -25 Degree * Exposted Polyurethane Surface are coated with * (-25 Degrees C ) to Degrees F (5 Degrees C) Monolar Mastic. * Design Load are Based on a Safety Factor of 5 with the MSS - SP58 and the ASME B Piping * Support Saddle are constructed on High Density * Technical Specification: AAAT - CS * Support Saddle restrains - Y movement. * Steel Component are constructed of A - Steel 2 " " 0" " " " " " HEAVY THICKNESS " - / 2 " 2 " 2- / 2 " " " 5 " " 7 " 8 " BOP BOP BOP BOP BOP BOP BOP BOP BOP BOP " " " 5 " 7 " 8 " 9 " " 5 " 0" 7 " 0" 9 " " 5 " " 7 " 8 " 9 " 0 " " " 0" 8 " 0" 20 " " " " 7 " 8 " 9 " 0 " " " 0" 8 " 0" 20 " " 7 " 8 " 9 " 0 " " " 5 " 7 " 0" 9 " 0" 2 " " 7 " 8 " 9 " 0 " " " 5 " 7 " 0" 9 " 0" 2 " " 8 " 9 " 0 " " " " " " 8 " 0" 20 " 0" " " 9 " 0 " " " " " 5 " 7 " 9 " 0" 2 " 0" 2 " " " " " " " " 5 " " 7 " 9 " 2 " 0" 2 " 0" 25 " " " " " 5 " " " " 7 " " 9 " 2 " 2 " 0" 25 " 0" 27 " " 5 " " " " 7 " " 8 " " 9 " " 2 " 2 " 25 " 0" 27 " 0" 29 " " 7 " 8 " 9 " 20 " " " 29 0" " 9 " 20 " " 2 " " 29 0" " " " 2 " 2 " " " 0" " 5 " 2 " " 25 " " " 0" 5 " 7 " 27 " 28 " 29 " 0 " 5 0" 7 0" 9 " " 29 " 0 " " " 5 7 0" 9 0" " " " " " " " " 0" " 5 " " " 5 " " 7 9 " 0" 0" 5 " 7 " 5 " " 7 " 8 " 9 " 0" 5 0" 7 " 9 " 7 " 8 " 9 " 0 " " 5 0" 7 0" 9 " " 9 " 0 " " " " 5 7 0" 9 0" " 5 " 7 " 7 " 5 7 " 7 " " 5 7 0" 55 7 " 57 7 " 5 7 " 7 " 7 7 " 8 7 " " " 57 7 "