HYDRAULIC CABLE WINCHES

Size: px

Start display at page:

Download "HYDRAULIC CABLE WINCHES"

Matilda Horton
5 years ago
Views:

Series 00 Galv Quality Since HYDRULI L WINHS The rugged construction and versatility of Series 00 Galv makes it adaptable to a wide range of applications.

1 Series 00 Galv Quality Since HYDRULI L WINHS The rugged construction and versatility of Series 00 Galv makes it adaptable to a wide range of applications. Series 00 direct drive winches are used for industrial pulling and dragging applications including rear load waste packers, drill rigs, fishing boats, marine craft. Series 00 Galv ase Mount Shown Low Profile Mount vailable GLVNIZD UP TO 12,000 POUNDS PITY loom TM GR S WORM SHFT WORM GR GR RTIO RINGS DRUM SHFT L DRUM Hydraulic able Winches Standard Features - Made of high strength cast iron. ompletely sealed for oil enclosed operation and to keep dirt out. - One piece alloy steel hardened and ground for extra durability. ompact design allows hydraulic motor to be coupled directly to worm. - High tensile aluminum-nickel alloy bronze. Optimum lead and pressure angles transmit maximum power to the drum. - 20:1 standard, :1, 27:1, 40:1 optional ratios provide optimum efficiency in power and speed. - Worm gear and worm shaft run on tapered roller bearings. Outer end housing has sealed ball bearing /2 diameter heat -treated alloy steel minimum tensile strength 150,000 psi. - Tough all steel construction resists breakage or warping. UTION: This winch model does not include any kind of holding brake. If your application requires a holding brake choose Lift-Safe winch series LSH or LSK with automatic hydraulic safety brakes.

2 Series 00 Galv Model Selection from Performance Data Quality Since MODL XMPL: --L8-20-LP-GLV Galvanized Gear ase and Shaft Designation = Series 00 Galv with 1-1/2 Drum Shaft Low Profile Mounting (specify with or without Hydraulic Motor Designation,,, DD,, G, 4.9, 6.2, 8.0, 9.6, 11.9 IS Input Shaft Drum Sizes S8, L8, XL, XL12, XL14 mounting angles) Gear Ratio :1, 20:1, 27:1, 40:1 DRUM PITY L DIMTR (IN.) 1/4 5/16 3/8 7/16 1/2 DRUM "S8" PITY (FT.) DRUM "L8" PITY (FT.) DRUM "XL" PITY (FT.) DRUM "XL12" PITY (FT.) DRUM "XL14" PITY (FT.)

3 PULL 1ST LYR OF L (LS.) PULL 1ST LYR OF L (LS.) PULL 1ST LYR OF L (LS.) Series 00 Galv Model Selection from Performance Data OIL PRSSUR (LS./SQ.IN.) G DD :1 RTIO (optional) G DD 4.9 L SPD 1ST LYR (FT./MIN.) 1 20:1 RTIO (standard) OIL PRSSUR (LS./SQ.IN.) L SPD 1ST LYR (FT./MIN.) 27:1 RTIO (optional) L SPD 1ST LYR (FT./MIN.) Quality Since OIL FLOW (GLLONS/MIN.) OIL FLOW (GLLONS/MIN.) DD G DD 9.6 G 11.9 DD G DD 9.6 G 11.9 PULL 1ST LYR OF L (LS.) OIL PRSSUR (LS./SQ.IN.) 40:1 RTIO (optional) L SPD 1ST LYR (FT./MIN.) OIL FLOW (GLLONS/MIN.) DD DD OIL PRSSUR (LS./SQ.IN.) OIL FLOW (GLLONS/MIN.)

4 Quality Since Dimensional Drawings Series 00 Galv S8 and L8 Drum ase Mount Model - Direct Drive

5 Quality Since Dimensional Drawings Series 00 Galv S8 and L8 Drum Low Profile Model - Direct Drive

6 Quality Since Dimensional Drawings Series 00 Galv XL, XL12 and XL14 Drum ase Mount Model - Direct Drive

orrect choice of Directional ontrol Valves for loom Winches Tandem enter Spool Valve Work Ports are blocked in neutral position Use on all winches that use motor only to hold load.

7 orrect choice of Directional ontrol Valves for loom Winches Tandem enter Spool Valve Work Ports are blocked in neutral position Use on all winches that use motor only to hold load. *Winches require ridged mounting plate. See owner s manual for information about proper mounting plate thickness or call loom Sales ngineer at factory WRNING! Goods are not intended for use in the moving or lifting of persons! The winches described herein are neither designed nor intended for use or application to equipment used in the lifting or moving of persons and it is understood that all such use shall be at the sole risk of the user. The cable clamps on winches are not designed to hold rated loads. minimum of 5 wraps of cable must be left on drum barrel to guarantee holding of rated load. pplications of winch where life would be endangered by any event are not recommended. LOOM Manufacturing Inc. Winch Division th Street,, Independence, Iowa FX PHON opyright 2015 loom Mfg. Inc.

Series Hydraulic Cable Winches Standard Features. Bloom TM

Series Hydraulic Cable Winches Standard Features. Bloom TM Series 10 HYDRULI L WINHS The rugged construction and versatility of Series 10 makes it adaptable to a wide range of applications. Series 10 direct drive winches are used for industrial pulling and dragging