P600 (MS-16D3) Disassembly Guide

Size: px

Start display at page:

Download "P600 (MS-16D3) Disassembly Guide"

John Taylor
5 years ago
Views:

1 P600 (MS-16D3) Disassembly Guide 1 BATTERY PACK 2 BOTTOM DOOR ASSY 3 HDD MODULE 4 ODD MODULE 5 THERMAL-KIT AND RAM 6 SEPARATE UPPER CASE AND LOWER CASE 7 LOWER CASE ASSY 8 UPPER CASE ASSY 9 LCD MODULE ASSY

2 1 BATTERY PACK 1.1:Move the Unlock button base on left picture shows; 1.2:Release the Release button and move the battery pack base on left picture. Battery Pack S9N SB3 1

3 2 BOTTOM DOOR ASSY 2.1:Remove the 10 screws (M2.5*4mm), then remove the Bottom door. Attention: the screw driver touque is: 2.3Kgf-cm Bottom door 307-6D2J211-SE0 1 Screw E H29 10

Attention: the screw driver torque: 3.0Kgf-cm Screw E43-1254002-H29 3 3.2 : Remove the 2 screws (M3*3.

4 3 HDD MODULE 3.1:Remove the 3 screws (M2.5*4mm); Then remove the HDD Module according to the direction as pic shows. Attention: the screw driver torque: 3.0Kgf-cm Screw E H : Remove the 2 screws (M3*3.5mm) that stabilize the bracket. Attention: the screw driver torque is 2.3Kgf-cm Screw E H :Remove the HDD bracket. HDD Bracket A89 1 HDD Module S W36 1

Then remove ODD Bracket as below. Attention: the screw driver torque: 2.

5 4 ODD MODULE 4.1: Remove the ODD Module according to the direction as pic shows. 4.2:Remove ODD Bezel as below. ODD Bezel 307-6D1F211-SE :Remove 2pcs screws (M2*3mm). Then remove ODD Bracket as below. Attention: the screw driver torque: 2.3Kgf-cm Screw E H29 2 ODD Bracket E2M-6D10112-A89 1 ODD Module S7D H44 1

5 THERMAL-KIT AND RAM 5.1:Remove the 3 screws(m2.

5*4mm),after that remove the thermal module.

6 5 THERMAL-KIT AND RAM 5.1:Remove the 3 screws(m2.5*4mm) and FAN cable, after that remove the Fan. Attention:the screw driver torque is 2.3Kgf-cm Screw E H29 3 Fan E A :Remove the 3 screws(m2.5*4mm),after that remove the thermal module. Attention:the screw driver torque is 2.3Kgf-cm Screw E H29 3 HEATSINK E TA :Push the two sides shielding of RAM as pic Shows, then remove the RAM module; after that remove the CPU. CPU A I06 1 RAM Module S7C-S S02 1

torque is 2.3Kgf-cm Screw E43-1203003-H29 7 6.

7 6 SEPARATE UPPER CASE AND LOWER CASE 6.1:Remove 7 screws(m2*3mm) Attention: the screw driver torque is 2.3Kgf-cm Screw E H :Remove 13 screws(m2.5*4mm) Attention: the screw driver torque is 2.3Kgf-cm Screw E H29 13

pic shows; then remove the cable; Keyboard

8 6 SEPARATE UPPER CASE AND LOWER CASE 6.3:Before remove K/B, firstly remove the upside, then remove the two sides, last remove the downside. 6.4 : Firstly push connector according to the direction as pic shows; then remove the cable; Keyboard S1N-3EUS231-SA : When remove the keyboard should notice the two bosses at bottom of the keyboard..

5*4mm); Attention: the screw driver torque is: 2.0-2.

7:First release the connector that stabilize the cable,

9 6 SEPARATE UPPER CASE AND LOWER CASE 6.6:Remove the 1 screw(m2.5*4mm); Attention: the screw driver torque is: Kgf-cm Screw E H :First release the connector that stabilize the cable, then remove Touchpad cable according to the direction that pic shows. 6.8:When remove the Upper case, detach the Upper case down side from Lower case;

5Kgf-cm Power Board 607-16D3C-01S 1 Screw E43-1254002-H29 1 7.

10 7 LOWER CASE ASSY 7.1:Remove the Power cable and the LVDS cable as pic shows. 7.2:Remove 1 screw (M2.5*4mm); then remove the Power board. Attention: the screw driver torque is Kgf-cm Power Board D3C-01S 1 Screw E H : Remove the 3 screws (M2.5*4mm); then remove the Audio board. Attention: the screw driver torque is Kgf-cm Audio board D3B-01S 1 Screw E H29 3

7 LOWER CASE ASSY 7.4 : Remove the 5screws (M2.

Attention: the screw driver torque is 2.0-2.

5:Remove the cable as pic shows. 7.6 : Remove the 1 screw (M2.

11 7 LOWER CASE ASSY 7.4 : Remove the 5screws (M2.5*4mm), then remove the main board from the Lower case. Attention: the screw driver torque is Kgf-cm Main Board D31-01S 1 Screw E H :Remove the cable as pic shows. 7.6 : Remove the 1 screw (M2.5*4mm); then remove the FFC and VGA board. Attention: the screw driver torque is 2.3Kgf-cm VGA board D3A-01S 1 Screw E H29 1

7 LOWER CASE ASSY 7.7:Remove the 1 screw (M2.

Attention: the screw driver torque is 2.5-3.

5*4mm) that stabilize the right LCD hinge.

12 7 LOWER CASE ASSY 7.7:Remove the 1 screw (M2.5*4mm) that stabilize the left LCD hinge. Attention: the screw driver torque is Kgf-cm Screw E H :Remove the 1 screw (M2.5*4mm) that stabilize the right LCD hinge. Attention: the screw driver torque is Kgf-cm Screw E H :Remove the Speaker module from lower case. Speaker Module S33-A F33 1 Lower Case 307-6D1D211-SE0 1

8 UPPER CASE ASSY 8.1:Remove the 2 screws (M2*3mm), then remove the T/P bracket.

0Kgf-cm T/P bracket E2M-6D10511-A89 1 Screw E43-1203003-H29 2 8.

0Kgf-cm F/P OS1-16D3001 1 Screw E43-1203003-H29 2 8.

13 8 UPPER CASE ASSY 8.1:Remove the 2 screws (M2*3mm), then remove the T/P bracket. Attention: the screw driver torque is Kgf-cm T/P bracket E2M-6D10511-A89 1 Screw E H :Remove the 2 screws (M2*3mm), then remove the F/P. Attention: the screw driver torque is Kgf-cm F/P OS1-16D Screw E H : Remove the Mylar and release the connector that stabilize the T/P cable, then remove the T/P module according to direction of pic shows; T/P module S E47 1 UPPER CASE 307-6D1C221-SE0 1 FFC Cable (To MB) K1C J36 1

2:Remove the 6 LCD rubbers. LCD Rubber E2Y-6911711-Y40 6 9.

14 9 LCD MODULE ASSY 9.1:Remove the two sides LCD HINGE-CAP. Hinge cap-l E2P H76 1 Hinge cap-r E2P H :Remove the 6 LCD rubbers. LCD Rubber E2Y Y :Remove the LCD bezel, should begin from downside to left side, then the upside to right side; LCD Bezel B211-U22 1

5:Remove the 3 screws (M2.5*5mm); Remove the left LCD hinge. Attention: the screw driver torque is 3.0-3.

15 9 LCD MODULE ASSY 9.4:Remove the 3 magnets on LCD cover; LCD Cover Magnet E2M SF7 2 LCD Cover Magnet E2M SF :Remove the 3 screws (M2.5*5mm); Remove the left LCD hinge. Attention: the screw driver torque is Kgf-cm Screw E H29 3 Hinge L E2M-6D10911-G :Remove the 3 screws (M2.5*5mm); Remove the right LCD hinge. Attention: the screw driver torque is Kgf-cm Screw E H29 3 Hinge R E2M-6D10811-G60 1

9 LCD MODULE ASSY 9.7:Remove the 4 screws (M2.

16 9 LCD MODULE ASSY 9.7:Remove the 4 screws (M2.5*4mm) Attention: the screw driver torque is Kgf-cm Screw E H :Firstly remove the Camera Cable, then remove the display module from LCD cover. 9.9:Remove the LVDS cable from display module; LVDS Cable K V03 1

0Kgf-cm Display Module S1J-642G004-CG1 1 LCD BRACKET-L E2M-6910211-A89 1 LCD

17 9 LCD MODULE ASSY 9.10:Remove the 8 screws (M2*3mm) Attention: the screw driver torque is Kgf-cm Display Module S1J-642G004-CG1 1 LCD BRACKET-L E2M A89 1 LCD BRACKET-R E2M A89 1 Screw E H :Remove the CMOS camera module according to the sequence as pic shows; Camera Module S1F AH3 1

18 9 LCD MODULE ASSY 9.12:Remove the MIC Module as left picture show MIC Module S K :Remove the WIRELESS board from LCD Cover. Antenna S U40-J :Remove the Bluetooth board from LCD Cover. Bluetooth LCD Cover A713-SE0 1

19 P600(MS-16D3)Screws specification Photo Screw specification Label (M2.5*L4MM)black (M2.5*L5MM)white (M2*L3MM)white (M3*L3.5MM) white

20 P600(MS-16D3)screws specification 1 BOTTOM DOOR ASSY total 22pcs screws specification: Photo Screw specification label (M2.5*L4MM) black

21 2 THERMAL-KIT 6pcs screws specification: P600(MS-16D3)screws specification Photo Screw specification label (M2.5*L4MM) black

22 P600(MS-16D3)screws specification 3 ODD and HDD ASSY total 4pcs screws specification: Photo Screw specification label (M3*L3.5MM) white (M2*L3MM)white

23 P600(MS-16D3)screws specification 4 LOWER CASE ASSY total 9pcs screws specification: Photo Screw specification label (M2.5*L4MM) black (M2*L3MM)white

24 P600(MS-16D3)screws specification 5 LCD Hinge total 2pcs screws specification: Photo Screw specification Label (M2.5*L4MM) black

25 P600(MS-16D3)screws specification 6 LCD MODULE ASSY total 18pcs screws specification: Photo Screw specification label (M2.5*L4MM) black (M2.5*L5MM)white (M2*L3MM)white

26 P600(MS-16D3)screws specification 7 TOUCHPAD total 4pcs screws specification: Photo Screw specification label (M2*L3MM) white

CX623 (MS-168A) Disassemble Guide

CX623 (MS-168A) Disassemble Guide 1 BATTERY PACK 2 BOTTOM DOOR ASSY 3 HDD MODULE 4 ODD MODULE 5 THERMAL-KIT CPU DRAM AND WLAN MODULE 6 SEPARATE UPPER CASE AND LOWER CASE 7 LOWER CASE ASSY 8 UPPER CASE