SAWMILL LIQUIDATION SMALL LOG MILL LARGE LOG MILL PLANER AND PACKAGING ROLLING STOCK AND FILING ROOM

Transcription

1 NACHES, WA SAWMILL LIQUIDATION on SMALL LOG MILL LARGE LOG MILL PLANER AND PACKAGING ROLLING STOCK AND FILING ROOM

2 SMALL LOG MILL EQUIPMENT #1 LOG DECK INFEED: ONE INFEED LOG DECK 35 FT. LONG X 30 IN. WIDE 6 RUNS OF #124 CHAIN 6 PIN STOPS S DRIVE INCLUDES HITACHI 20 HP. 60 R.P.M. GEAR REDUCER 2 STOP AND LOADS SUB-STEEL TO GROUND. #2 LOG CONVEYOR: ONE LOG TROTH CONVEYOR 45 FT. LONG - #112 MILL CHAIN S DRIVE WITH 10 HP. 45 R.P.M. SKK GEAR REDUCER. #3 LOG CUT OFF SAW: ONE 72 IN. DIAMETER LOG CUT OFF SAW SWING TYPE INSERT TOOTH 100 HP. BELT DRIVEN ARBOR TWO AIR LOG HOLD DOWNS 30 HP. HYDRAULIC POWER UNIT INCLUDES SAW SHARPENER AND ONE SPARE SAW BLADE. #4 LOG STOPS WITH LOG CONVEYOR & KICKER: LOG STOPS: 8 FT. 10 FT. 12 FT. 14 FT FT.-18 FT. 20 FT. AIR ACTUATED WITH VALVES 30 FT. LOG HAUL CONVEYOR WITH #112 MILL CHAIN S DRIVE 10 HP. 45 R.P.M. SKK GEAR REDUCER LEFT HAND LOG DISCHARGE VIA PUNCH AND DIE KICKERS AIR ACTUATED. #5 LOG HAUL CONVEYOR: ONE 30 FT. LONG LOG HAUL CONVEYOR TO DEBARKER INFEED WITH #112 MILL CHAIN S DRIVE WITH 10 HP. 40 R.P.M. SKK GEAR REDUCER. (RIGHT HAND

3 CONVEYOR) #6 NICHOLSON 27 DEBARKER A-1: ONE NICHOLSON 27 IN. MODEL A-1 RING DEBARKER - SER. # (MFG 1981) SIX (6) TOOL ARM MACHINE AIR HOLD DOWNS HYDRAULIC RING CENTERING AUTOMATIC HOLD DOWNS AND RING CENTERING 75 HP. TWO SPEED RING DRIVE - 25 HP. TWO SPEED FEEDWORKS DRIVE FALK GEAR REDUCER 20 HP. HYDRAULIC POWER UNIT RING LUBE PUMP OPERATORS CONTROL CAB AND CONTROLS. POWERED INFEED HOURGLASS ROLLS CENTERING ROLL. (NOTE: NEW RING BEARING AND AIR SEAL INSTALLED IN 2004). MACHINE HAS ONLY BEEN OPERATED ON A SINGLE SHIFT BASIS.

4 #7 LOG HAUL CONVEYOR (barker outfeed): ONE 30 FT. LONG LOG HAUL CONVEYOR WITH #112 LADDER CHAIN S DRIVE WITH RIGHT HAND PUNCH AND DIE KICKER SKK 10 P. 41 R.P.M. GEAR REDUCER. #8 LOG INFEED TRANSFER TO MAXI- MILL: ONE LOG INFEED TRANSFER DECK, FIVE (5) RUNS OF #124 MILL CHAIN 45 FT. OVERALL LENGTH S DRIVE FIVE (5) PIN STOPS AT THE DISCHARGE END 20 HP. 40 R.P.M. HITACHI GEAR REDUCER. #9 MAXI MILL SYSTEM: ONE MAXI-MILL SMALL LOG BREAKDOWN SYSTEM - 8 FT. TO 20 FT. LOG LENGTHS X 22 IN. DIAMETER CAPACITY. COMPLETE SYSTEM INCLUDES THE FOLLOWING: INFEED TO CHARGER X/Y CHARGER, OVERHEAD END DOGGING CARRIAGE WITH 90 DEGREE INDEX FOR CUTTING 4 SIDED CANTS 150 HP. DC CARRIAGE DRIVE AND SCR CONTROLLER 85 FT. 120 LB V AND FLAT RAIL BUMPER STOPS TWIN 8 KNIFE TM7E SLABBERS WITH 150 HP. MOTORS QUAD SIX 6FT. KLAMATH IRON WORKS MECHANICAL STRAIN BANDMILLS WITH 150 HP. MOTORS OUTFEED CANT/BOARD ROLL CASE AND TRANSFER FOUR (4) 40 HP. HYDRAULIC PUMPS AND MOTORS FLOODED SUCTION WITH RESERVOIR AND HEAT EXCHANGER. OPERATORS CONTROLS AND MOTOR CONTROL CENTER. THIS WAS INSTALLED IN THE EARLY 80 S AND IS IN GOOD TO VERY GOOD CONDITIONS. #10 KLAMATH 6 FT. LINE BAR RESAW: - FIXED LINE BAR MOVEABLE SAW V AND FLAT WAY

5 DESIGN MOVEABLE TOP GUIDE TILT BACK WHEEL GUARD 20 FT. INFEED ROLL CASE ROLLS ARE 10 IN. DIAMETER X 26 IN. WIDE JUMP CHAINS CANT TURNER. (New band wheels in 2005) #10A - CANT/LUMBER TRANSFER ( TO RESAW FROM MAXI-MILL): ONE CANT /LUMBER TRANSFER FROM MAXI-MILL TO RESAW INFEED ROLLCASE - (5) RUNS # 78 MILL CHAIN - 10' OVERALL LENGTH = S DRIVE - WITH 5 HP - 40 RPM HITACHI GEAR REDUCER. #10B - RESAW OUT FEED ROLLCASE: ONE RESAW OUTFEED ROLLCASE 25' OVERALL LENGTH, ROLLS ARE 8" DIAMETER X 48" WIDE. #11 - BOARD TRANSFER TO EDGER: ONE BOARD TRANSFER TO EDGER - 6 RUNS OF # 78 MILL CHAIN - 24' LONG X 18' WIDE - S DRIVE - HITACHI 5 HP - 40 RPM GEAR REDUCER. #12 - CANT LANDING TABLE: ONE CANT LANDING TABLE - 10' OVERALL LENGTH X 10' WIDE - # 138 CAMEL BACK CHAIN - WITH 5 HP - 40 RPM HITACHI GEAR REDUCER. #13 - LUMBER TRANSFER (TO EDGER): ONE LUMBER TRANSFER TO EDGER - 8' LONG X 18' WIDE - 7 RUNS OF # 78 CHAIN - S DRIVE - 5 HP - 40 RPM HITACHI GEAR REDUCER. #14 - SCHURMAN EDGER SYSTEM: ONE SCHURMAN MODEL 4TA48 BOARD EDGER - S/N TOP KEYED ARBOR - ONE FIXED SAW - TWO MOVEABLE - AIR SETWORKS - RIGHT HAND GATE - MOVEABLE LASER LIGHTS HP ARBOR 1, , , , , , Missing Photo

6 DRIVE - TWO SPEED FEEDWORKS - INFEED TABLE INCLUDES JUMP CHAINS - MOVEABLE LINE BAR - BOARD TURNERS - OUTFEED TABLE INCLUDES MOVEABLE POTLATCH EDGING PICKERS. #15 LANDING TABLE (Behind Edger): ONE 8 FT. LONG X 14 FT. WIDE FIVE (5) STRAND #138 CAMEL BACK CHAIN WITH 5 HP. 40 R.P.M. Hitachi gear reducer. # 16 - LUMBER TRANSFER: ONE LUMBER TRANSFER, 5 STRAND -35' LONG X 14' WIDE - # 78 MILL CHAIN - WITH 5 HP - 40 RPM HITACHI GEAR REDUCER. #17 - LUMBER TRANSFER - (UNDER RESAW OUTFEED): ONE LUMBER TRANSFER, 5 STRAND - 12' LONG X 14' WIDE - # 78 MILL CHAIN - WITH 5 HP - 40 RPM HITACHI GEAR REDUCER. # 18 - LUMBER TRANSFER: ONE LUMBER TRANSFER, 5 STRAND - 12' LONG X 14 WIDE - # 78 MILL CHAIN WITH AIR ACTUATED PIN STOPS - 5 HP - 40 RPM HITACHI GEAR REDUCER. 1, , , ,200.00

7 #19 - LUMBER TRANSFER: ONE LUMBER TRANSFER, 5 STRAND - 12' LONG X 14' WIDE - # 78 MILL CHAIN WITH TIPPLE GATE - AIR ACTUATED - 5 HP - 40 RPM HITACHI GEAR REDUCER. #20 - IRVINGTON MOORE TRIMMER SYSTEM: ONE IRVINGTON MOORE LEFT HAND - 4" TRIMMER SYSTEM - TRIM 20' PASS 26' - 40 HP LINE SHAFT DRIVE - S/N L - AIR OPERATED DROP SAWS - WITH GATHERING CHAINS - LUG FEEDER - AIR LEAF FENCE. 10 HP SCR FEEDWORKS DRIVE. #21 - LUMBER ROLLCASE (BEHIND TRIMMER TO SORTER): ONE ROLLCASE TRANSFERRING LUMBER FROM THE TRIMMER TO THE LSI SORTER - POWERED ROLLS ARE 8" DIAMETER X 36" WIDE, 50' OVERALL LENGTH WITH 10 HP RPM HITACHI GEAR REDUCER. 1,700.00

8 #22 - ROLLCASE BEHIND RESAW: ONE 38' POWERED ROLLCASE, 8" DIAMETER X 46" WIDE ROLLS - WITH 10 HP RPM HITACHI GEAR REDUCER. #23 - OVER HEAD LANDING TABLE: ONE LANDING TABLE (6) RUNS #138 CHAIN 8 FT. LONG X 14 FT. WIDE WITH 5 HP. 40 R.P.M. GEAR REDUCER. # 24 - FLOOR CHAINS (PIT): ONE FLOOR CHAINS - 12 RUNS OF # 78 MILL CHAIN WITH LUGS - 28' LONG X 25' WIDE - WITH 10 HP - 30 RPM HITACHI GEAR REDUCER. # 25 - BELT CONVEYOR (FROM SWAMP LINE TO RESAW LANDING TABLE): 1, , ONE PAN TYPE BELT CONVEYOR - 100' LONG X 18" WIDE X 12" DEEP - WITH RETURN PAN - 15 HP RPM HITACHI GEAR REDUCER. #26 - LANDING TABLE & TRANSFER TO RESAW: ONE COMBINATION LANDING TABLE AND TRANSFER, LANDING TABLE HAS 5 RUNS OF # 138 CAMEL BACK CHAIN AND 5 RUNS OF # 78 MILL CHAIN - 17' OVERALL LENGTH. WITH 5 HP - 40 RPM HITACHI GEAR REDUCER. #27 - BARKER AND HOG MCC: 1, SELL WITH BARKER #28 - MAXI MILL MCC: SELL WITH MAXI-MILL

9 #28A - MAXI MILL MCC: SELL WITH MAXI-MILL #29 - HOG MCC: SELL WITH HOG #30 - TRIMMER MCC: SELL WITH TRIMMER #31 - LSI SORTER: ONE LSI RIGHT HAND 19 BIN - J BAR SORTER - 20' LONG MATERIAL WITH 25 HP HYDRAULIC POWER UNIT - 4 RUNS TAKE AWAY CHAINS MODEL INCLUDES ALL DRIVES AND GEAR REDUCERS - BUILDING ROOF AND TRUSSES.

10 #32 - LUNDEEN 20' STACKER: ONE LUNDEEN 20' RIGHT HAND STACKER SYSTEM - WITH STICK LAYER, INCLUDES UNSCRAMBLER - TRANSFER CHAINS TO THE STACKER AS WELL AS PACKAGE REMOVAL - ALL ELECTRICAL - HYDRAULIC AND GEAR REDUCERS. NOTE: NO BUILDING

11

12 MILL WASTE SYSTEM #33 - WASTE CONVEYOR UNDER THE MAX-MILL: ONE WASTE CONVEYOR - 87' OVERALL LENGTH - 18" WIDE X 18" DEEP - #112 CHAIN WITH FLIGHTS - 10 HP - 40 RPM HITACHI GEAR REDUCER. $ 5, #34 - WASTE CONVEYOR - SECTION # 2 (MAIN): ONE WASTE CONVEYOR - 70' OVERALL LENGTH - 18" WIDE X 18" DEEP - #112 CHAIN WITH FLIGHTS - 10 HP - 40 RPM HITACHI GEAR REDUCER - NEW CHAIN. #35 - WASTE CONVEYOR ( UNDER RESAW): ONE WASTE CONVEYOR - 18' OVERALL LENGTH - 18" WIDE X 18" DEEP - #112 CHAIN - 5 HP 40 RPM HITACHI GEAR REDUCER. #36 - WASTE CONVEYOR (UNDER EDGER): 1, ONE WASTE CONVEYOR - 30' OVERALL LENGTH - 18" WIDE X 18" DEEP - #112 CHAIN - 5 HP 40 RPM HITACHI GEAR REDUCER. #36A - WASTE CONVEYOR - (UNDER EDGER INFEED): SOLD ONE WASTE CONVEYOR - 20' OVERALL LENGTH - 18" WIDE X 18" DEEP - #112 CHAIN - 5 HP - 40 RPM HITACHI GEAR REDUCER. #37 - WASTE CONVEYOR (TRIMMER TO MAIN WASTE): 2,200.00

13 ONE WASTE CONVEYOR - 72' OVERALL LENGTH - 18" WIDE X 18" DEEP - #112 CHAIN - 10 HP - 40 RPM HITACHI GER REDUCER. # 38 - WASTE CONVEYOR (TRIMMER TO MAIN WASTE): ONE WASTE CONVEYOR - 72' OVERALL LENGTH - 18" WIDE X 18" DEEP - #112 CHAIN - 10 HP - 40 RPM HITACHI GER REDUCER. #39 - VIBRATING CONVEYOR: 2, ONE GENERAL KINEMATICS 68' LONG BALANCED VIBRATING WASTE CONVEYOR, S/N / M.O X2X68-1/4" PAN THICKNESS - 5' FIBERGLASS METAL DETECTOR SECTION - 24" WIDE X 12" DEEP - WITH 24' SAWDUST AND CHIP SHAKEOUT SCREENS - RIGHT HAND DISCHARGE - TRANSITION TO A KOCKUMS 58" CHIPPER SPOUT. 10 HP TEFC DRIVE MOTOR. # 39A - MDI METAL DETECTOR /SEARCH COIL: ONE MDI MODEL CCW -78 METAL DETECTOR WITH 30" WIDE SEARCH COIL, S/N PRICE $1,900 # 40-58" KOCKUMS CHIPPER: ONE KOCKUMS 58"BIG MOUTH CHIPPER - MODEL 58 - S/N (8) EIGHT KNIFE - HORIZONTAL FEED - TOP DISCHARGE. (DISK NEEDS REBUILDING) WITH 200 HP RPM ODP MOTOR. BELT DRIVE. INCLUDES PIPE TO SURGE BIN.

14 # 41 - CHIP SURGE BIN: ONE 6 UNIT DOUBLE AUGER SURGE/METERING BIN - WITH 7 ½ HP - 40 RPM HITACHI GEAR REDUCER. 1, # 42 - KOCKUMS 7' X 7' CHIP SCREEN: ONE KOCKUMS MODEL KS-77 CHIP SCREEN - S/N ' X 7' #43 - OVERS CONVEYOR: ONE OVERS CONVEYOR 26 FT. OVERALL LENGTH 17 IN. WIDE WITH #112 CHAIN WITH 5 HP. 40 R.P.M. HITACHI GEAR REDUCER. # 44 - DUST CONVEYOR - (FROM VIBRATING CONVEYOR TO SURGE BIN): ONE DUST CONVEYOR - 60' OVERALL LENGTH - 17" WIDE - #112 CHAIN - WITH 7 ½ HP - 40 RPM HITACHI GEAR REDUCER. # 45 - CHIP CONVEYOR - FROM VIBRATING CONVEYOR TO SURGE BIN ONE CHIP CONVEYOR: 1, ' OVERALL LENGTH - 12" WIDE - #110 CHAIN - WITH5 HP - 40 RPM HITACHI GEAR REDUCER. # 46 - CHIP CONVEYOR -(FROM SCREEN TO TRUCK BIN): ONE CHIP CONVEYOR, 115' OVERALL LENGTH - 14" WIDE - #112 CHAIN WITH FLIGHTS - 15 HP - 40 RPM HITACHI GEAR REDUCER.

15 #47 - HIGH PRESSURE BLOWER: ONE SUTOBILT 10 X 24 HIGH PRESSURE BLOWER - VERTICAL INLET AND DISCHARGE - WITH 125 HP BELT DRIVE INCLUDES DONALD SON 2' X 6' HIGH INLET MUFFLER AND 24 X 9' HIGH DISCHARGE MUFFLER - MERCOID PRESSURE SWITCH. #48-20 X 20 FEEDER: ONE RADAR MODEL 20 X 20 ESW - S/N 921 FEED WITH 5 HP MOTOR AND DODGE SHAFT MOUNT GEAR REDUCER - 8" INJECTION T. # 49-8" BLOW PIPE WITH TWO WAY DIVERTER: PRICE $ 1.50 PER LINEAR FOOT 500 FT. SOLD # 50 FIRST - 30 UNIT TRUCK BIN: ONE 30 UNIT PEERLESS TRUCK BIN WITH MAN LADDERS - CAT WALKS - LEVELING AUGER - BINDICATOR S HYDRAULIC GATES (No Hydraulic Power Unit)

16 # 51 SECOND - 30 UNIT TRUCK BIN: ONE 30 UNIT PEERLESS TRUCK BIN WITH MAN LADDERS - CAT WALKS - LEVELING AUGERS - BINDICATORS HYDRAULIC GATES (No Hydraulic Power Unit) #52-14 UNIT TRUCK BIN: ONE 14 UNIT TRUCK BIN WITH 6' CYCLONE - MAN LADDERS - HYDRAULIC GATES. (No hydraulic power unit) HAS BEEN DISASSEMBLED. # 52-A - HYDRAULIC POWER UNIT FOR TRUCK BINS: ONE 10 HP HYDRAULIC POWER UNIT FOR THE TRUCK BINS, WITH RESERVOIR.

17 # 53 - BARK CONVEYOR: ONE BARK CONVEYOR - 62' OVERALL LENGTH - #112 CHAIN - 18" WIDE X 18" DEEP - WITH 5 HP - 40 RPM HITACHI GEAR REDUCER. # 54 - DUST CONVEYOR - UNDER CUT OFF SAW: ONE DUST CONVEYOR - 34' OVERALL LENGTH - #112 CHAIN - 18" WIDE X 18" DEEP - WITH 5 HP - 40 RPM HITACHI GEAR REDUCER. # 55 - BARK CONVEYOR : ONE BARK CONVEYOR - 65' OVER ALL LENGTH - #112 CHAIN - 18" WIDE X 18" DEEP - WITH 5 HP - 40 RPM HITACHI GEAR REDUCER. #56 - HOG INFEED CONVEYOR: ONE HOG INFEED CONVEYOR - INCLINE TYPE - 75' OVERALL LENGTH, #112 CHAIN - 18" WIDE X 18" DEEP - WITH 10 HP - 40 RPM HITACHI GEAR REDUCER. # 57 - JEFFERY HAMMER HOG: 1, , , ONE JEFFERY MODEL WB-45 HAMMER HOG - S/N WITH 200 HP 1770 RPM MOTOR - BELT DRIVE - WITH INFEED CHUTE. GOOD CONDITION

18 # 58 - DISCHARGE CONVEYOR: ONE HOG DISCHARGE CONVEYOR - 110' OVERALL LENGTH - #112 CHAIN - INCLINE TO DEEP PILE HOG FUEL. #59 BOILER FUEL SILO: ONE BOILER FUEL SILO 80 UNITS 9,500.00

19 FILING ROOM EQUIPMENT AND ROLLING STOCK # 63 - KNIFE SHARPENER: HANCHET MODEL 54-LG - S/N SHOP 60 - $ #64 BANDSAW BENCH WITH STRETCHER ROLL: ONE ARMSTRONG #4 BANDSAW STRETCHER ROLL SER. #13776 WITH TWO 12 IN. X 48 IN. X 4 IN. THICK ANVILS AND ARMSTRONG #14 HEATED WELDING CLAMP. 3, # 65 - DUAL SIDE GRINDER: ONE BELL MODEL W S/N 81H2 DUAL SIDE GRINDER. # 66 - SYSTEMATIC GRINDER: ONE SYSTEMATIC MANUAL TOPPER FACER GRINDER WITH STAND. # 67 - ACME SAW GRINDER: CIRCLE SAW GUMMER GRINDER - S/N TALL MODEL # 68 - CIRCLE SAW STRETCHER ROLL: ONE ARMSTRONG MODEL 3-10 CIRCLE SAW STRETCHER ROLL - S/N # 69 - BANDSAW GUIDE DRESSER: ONE THOMPSON MODEL B - S/N 542 BANDSAW GUIDE DRESSER 1, ,

20 # 70 - BANDSAW SHARPENER: ONE ARMSTRONG # 4 LEFT HAND BANDSAW GRINDER - S/N WITH FILING CLAMP AND SAW STANDS # 71 - BANDSAW SHARPENER: ONE ARMSTRONG # 4 RIGHT HAND BANDSAW GRINDER - S/N WITH FILING CLAMP AND SAW STANDS. # 72 - SCHURMAN GUIDE DRESSER 6, , (Will be included in sale of Board Edger) # 74 - TM&E BENT KNIFE GRINDER ONE TM&E BENT KNIFE GRINDER - STACK GRINDER TYPE MODEL MK ROLLING STOCK #75 - PURCHASED IN HYSTER MODEL H- 190 H- S/N FOO7EO S/O ,676 24" TIRES PERKINS DIESEL ENGINE53" LONG FORKS - 148" LOAD HEIGHT - FORK POSITIONERS SIDE SHIFT - 7,400 HRS. ENCLOSED CAB WITH AC/HEATER AUTO SHIFT #76 - CAT MODEL 966D, S/N 99Y03251 WITH MEDFORD LOG FORKS, 26.5X25 TIRES # 77 - HYSTER MODEL HI50 MANUAL TRANSMISSION - PERKINS DIESEL ENGINE W/O SIDE SHIFT

21 #78 - HYSTER MODEL H150 - MANUAL TRANSMISSION - PERKINS DIESEL ENGINE W/O SID SHIFT. #79 - CAT MODEL 966C - S/N 76J2671 PARTS MACHINE # FORD CAB-OVER LUMBER TRUCKS (YARD) PRICE $900 EACH (TWO) 1,800.00

22 AIR SYSTEM MILL PARTS INVENTORY # HP AIR COMPRESSOR: ONE QUINCY NORTHWEST MODEL 740 -B - S/N ROTARY SCREW AIR COMPRESSOR - NEW AIR END IN AIR COOLED # HP AIR COMPRESSOR: QUINCY NORTHWEST MODEL Q241-D - S/N AIR COOLED SKID MOUNTED WITH STARTER # 85 - AIR DRYER: ONE PNEUMATECH MODEL AD-750 REFRIGERANT TYPE AIR DRYER. # 86 - AIR RECEIVER TANK: 1, ONE AIR RECEIVER TANK - 48" DIAMETER X 10' HIGH (VERTICAL) 125 PSIG - WITH WASHINGTON STATE INSPECTION. # 87 - NEW 6' KLAMATH IRON WORKS WHEEL: 10" FACE WITH ARBOR # 88 - MILL MACHINERY PARTS INVENTORY: BEARINGS ARE SOLD SPROCKETS ARE SOLD

23

24 LARGE LOG MILL EQUIPMENT #B-1 - INFEED LOG DECK: ONE INFEED LOG DECK - 6 RUNS OF #132 CHAIN - 32' LONG X 26' WIDE SPLIT DIVES - TWO (2) SKK 15 HP GEAR REDUCERS - (6) SIX PIN STOPS FOR FEEDING INTO LOG TROTH CONVEYOR - WITH 20 HP HYDRAULIC POWER UNIT. #B-2 - DEBARKER INFEED CONVEYOR: ONE 40' LARGE LOG INFEED CONVEYOR - C-131 CHAIN - S DRIVE - 15 HP RADICON GEAR REDUCER. #B-3 - NICHOLSON 60" RING DEBARKER SYSTEM: ONE NICHOLSON MODEL A-2-60" RING DEBARKER - S/N WITH LARGE LOG BY-PASS - 78" DIAMETER - 4 TOOL ARM MACHINE - 75 HP R.P.M. FEEDWORKS DRIVE SKK 35:1 GEAR REDUCER - RING DRIVE IS A 125 HP R.P.M. MACHINE WAS REBUILT IN 2003 WITH A NEW RING BEARING AND AIR SEALS - SYSTEM INCLUDES CAB WITH CONTROLS - 3 SECTION MCC CENTER - 20 HP HYDRAULIC POWER UNIT - RING LUBE PUMP -AUTO HOLDOWN AND RING CENTERING.

25 #B-4 - POND SAW: ONE CHAIN POND SAW - 6' BAR - 10 HP WITH LOG LIFTER 1, #B-5 - STRETCHER ROLL/BENCH: ONE ARMSTRONG #5 BANDSAW STRETCHER ROLL S/N 5665 WITH TWO 14" WIDE X 48" LONG X 4" THICK ANVILS AND WELDING CLAMP # B-6 - BANDSAW SHARPENER: ONE ARMSTRONG MODEL 6D RIGHT HAND BANDSAW SHARPENER WITH FILING CLAMP AND STANDS - S/N 5582 CAST MACHINE. # B-7 -BANDSAW SHARPENER: ONE ARMSTRONG MODEL 4 RIGHT HAND BANDSAW SHARPENER WITH FILING CLAMP AND STANDS - S/N CAST FRONT MACHINE. 1, , , # B-8 - CIRCLE SAW SHARPENER: ONE ACME CIRCLE SAW SHARPENER

26 # B-9 - KNIFE GRINDER: ONE HANCHET MODEL DN-40 S/N 9201-P # B-10 - BABBITT POT ONE RITE-HEAT 30 QUART BABBITT POT VOLT. # B-11 CHIPPER: ONE BLACK CLAWSON MODEL 6120 S/N CHIPPER -60" DISK - SIX KNIFE - HORIZONTAL FEED - SLANT DISK TYPE - WITH 200 HP TEFC 1200 RPM MOTOR. BELT DRIVE - WORN DISK 7, # B-11 A SPARE CHIPPER MOTOR: RE- BUILT ODP 2,000.00

27 LAYMAN LUMBER PLANER MILL AREA #P-1 PLANER- INFEED BRIDGE PLANER: ONE STETSON ROSS MODEL 505-E PLANER INFEED - 7' LONG BRIDGE - STETSON ROSS MODEL 6-12-C1 PLANER WITH PROFILES- S/N IN. WIDE - 16 KNIFE HEADS HP TOP HEAD - 65 HP BOTTOM HEAD. INSIDE HEAD IS HP OUTSIDE HEAD IS 65 HP. - PROFILE TOP HEAD IS 65 HP. PROFILE BOTTOM HEAD IS. #P-2 STETSON ROSS GRINDER: STETSON ROSS MODEL 372 SIDE HEAD GRINDER #P-3 KNIFE GRINDER: ONE HANCHET MODEL DN-40 - S/N 9149 KNIFE GRINDER #P-4 COE HYDRAULIC BREAKDOWN: 1, ONE USED COE HYDRAULIC 20 FT. X 54 IN. HIGH PACKAGE BREAKDOWN TILT HOIST SYSTEM <-> FOUR INFEED CHAINWAYS WITH #78 CHAIN AND 7-1/2 HP. GEARHEAD <-> FOUR ARM COE TILT HOIST AND 20 HP. HYDRAULIC POWER UNIT WITH 50 GALLON TANK WITH 30 X 30 IN. HEAT EXCHANGER <-> 57 IN. ELEVATION TO THE TOP OF INFEED

28 CHAINWAYS - FROM LEFT TO RIGHT CHAINWAYS ARE - 0" - 40" - 51" - 68" SPACING <-> TILT HOIST FOUR ARMS ARE ON A 57 IN. CENTER. #P-5 - LOW PRESSURE BLOWER: ONE LOW PRESSURE 6' BLOWER - 28" INLET 3, #P-6 - PEERLESS TRUCK BIN: ONE PEERLESS 62 UNIT MONO STYLE TRUCK BIN - S/N WITH 10 HP HYDRAULIC POWER UNIT - MAN LADDERS - CATWALKS - LEVELING AUGER #P-7- PACKAGE MAKER: ONE MAC-FAB 20' PACKAGE MAKER - WITH INFEED TO END SQUEEZE - RETRACTABLE GATE - SIGNODE MODEL M22LP S/N 018 SIDE AND TOP LUMBER SQUEEZE AND BANDER - WITH BOTTOM CORNER PROTECTORS. ALL HYDRAULICS AND PLC INCLUDED 45,000.00

29 P-8 - KILN CARTS: APPROXIMATELY GOOD CONDITION - 9' I BEAM CONSTRUCTION PRICE EACH $ LOTS OF 25 MINIMUM SOLD 162 CARTS SOLD 300 FT. OF RAIL 3,750.00

30