KITCHEN, CROCKERY, CUTLERY, COOKWARE & STORAGE

Transcription

1 KITCHEN, CROCKERY, CUTLERY, COOKWARE & STORAGE TABLE OF CONTENTS Food contact supplementary Cutlery, Knife blocks, Kitchen & BBQ utensils, Dish drainer Glassware, Ceramicware, Plasticware Oven & hob cookware Paper partyware Storage tins, bread bins, biscuit tins Page 1 of 1

2 Number JDW0048 Creation Date 1 st May 2014 Revision No. V1.0 Revision Date Food contact supplementary protocol REGULATORY REQUIREMENTS AND METHODS (Legal requirements are those stated in law that must be fulfilled) Food Grade Safety - Plastic With reference to EN 1186.Regulation (EU) No 10/2011 and - Overall migration 10 mg/dm2 or 60 mg/kg Simulants used dependent upon product usage - Specific migration Test requirements dependent on the type of plastic (the exhaustive list of authorised additives and monomers in accordance with the Regulation is not provided in this document) Actual testing will be conducted on polycarbonate. epoxy resin and PVC materials for specific migration of Bisphenol-A (BPA). * Commission Regulation (EU) No 284/2011 If the kitchenware is imported from China, declaration is required for Specific Migration Limit of 1. Primary Aromatic Amines (PAAs) for polyamides (e.g. nylon) 2. Formaldehyde for melamine (Test simulants shall be selected to fit the purpose for end use) Page 1 of 3

3 Number JDW0048 Creation Date 1 st May 2014 Revision No. V1.0 Revision Date Food contact supplementary protocol REGULATORY REQUIREMENTS AND METHODS (Legal requirements are those stated in law that must be fulfilled) Leachable Lead & Cadmium 84/500/EEC Shall comply with 84/500/EEC (Applicable to ceramic ware and glassware) Category 1 (articles which cannot be filled and articles which can be filled, the internal depth of which does not exceed 25 mm) 0.8 mg/dm 2 (Lead) 0.07 mg/dm 2 (Cadmium) Category 2 (all other articles that are not in Categories 1 or 3) 4.0 mg/l (Lead) 0.3 mg/l (Cadmium) Food Grade Safety - Metal Food Grade Safety - Wood Food Grade Safety - Paper Extractive method, analyzed by ICP- AES or AAS With reference to ISO Various Category 3 (cookware, packaging and storage vessels having a capacity of more than 3L) 1.5 mg/l (Lead) 0.1 mg/l (Cadmium) With reference to 1935/2004/EC, Article 3 1 mg/kg (Extractable Chromium) 0.07 mg/kg (Extractable Nickel) 0.02 mg/kg (Extractable Lead) mg/kg (Extractable Cadmium) 5 mg/kg (Extractable Copper) 0.05 mg/kg (Extractable Cobalt) 2 mg/kg (Extractable Aluminium) 0.6 mg/kg (Extractable Manganese) With reference to 1935/2004/EC, Article 3 5 mg/kg (Pentachlorophenol) Shall comply with Council of Europe Resolution AP (2002) 1. Restrictions of Cadmium less than 0.002mg/dm2 Lead less than 0.003mg/dm2 Mercury less than 0.002mg/dm2 PCP less than 0.015mg/Kg Page 2 of 3

4 Number JDW0048 Creation Date 1 st May 2014 Revision No. V1.0 Revision Date Food contact supplementary protocol REGULATORY REQUIREMENTS AND METHODS (Legal requirements are those stated in law that must be fulfilled) Food Grade Safety - Rubber With reference to EN 1186 Shall comply with Council of Europe Resolution AP (2004) 4. Restrictions N-nitrosamines N-nitrosatable substances Aromatic amines Food Grade Safety - Silicone Rubber Food Grade Safety - Organic Coating With reference to EN 1186 With reference to EN 1186 (Test simulants shall be selected to fit the purpose for end use) Shall comply with Council of Europe Resolution AP (2004) 5. Overall migration limit less than 10mg/dm2 or 60mg/Kg of foodstuff (Test simulants shall be selected to fit the purpose for end use) Shall comply with Council of Europe Resolution AP (2004) 1. Overall migration limit less than 10mg/dm2 or 60mg/Kg of foodstuff (Test simulants shall be selected to fit the purpose for end use) The Company s consulting services are governed by and subject to the SGS General Conditions of Service at http// SGS SA. All rights reserved Page 3 of 3

5 Number JDW0047 Creation Date 1st May 2014 Revision No. V1.0 Revision Date Test Protocol Cutlery, knife blocks and kitchen utensils, BBQ utensils, dish drainer REGULATORY REQUIREMENTS AND METHODS (Legal requirements are those stated in law that must be fulfilled) REACH Regulations, Article 67(1). (REACH Annex XVII) 1907/2006 and 1907/2006 and Article shall contain allowable amounts of restricted substances according to the conditions laid down in REACH Annex XVII. REACH Regulations, Article 33. General Products Safety Directive (GPSD) Packaging and Packaging Waste for environmental - Toxic Elements Tests on Packaging Material Timber Regulation Obligations of operators who place timber and timber products on the market Persistent organic pollutants (POPs) General Requirements For All Food Contact Materials 1907/2006 and (Screening Test) Directive 2001/95/EC Directive 94/62/EC Acid digestion, analyzed by AAS or ICP-AES Regulation (EU) No 995/ /2004 and 1935/2004 Articles containing substances of very high concern (SVHC) listed in the candidate list for authorisation > 0.1% w/w require communication in the supply chain. The product shall comply with the essential safety requirements of the GPSD(2001/95/EC). The manufacturer shall conduct and document a risk assessment of the product. Must meet the requirements of European Directive 94/62/EC and its. The total toxic element content in the packaging material shall not exceed 0.01% by weight for Lead, Cadmium, Mercury & Hexavalent Chromium. The Regulation lays down the obligations of operators who place timber products on the internal market for the first time, as well as the obligations of traders Articles shall be free from Persistent organic pollutants (POPs) to the level set by the regulation. Articles shall comply to the essential requirements of the General Requirements For All Food Contact Materials 1935/2004 Page 1 of 3

6 Number JDW0047 Creation Date 1st May 2014 Revision No. V1.0 Revision Date Test Protocol Cutlery, knife blocks and kitchen utensils, BBQ utensils, dish drainer PERFORMANCE TESTING (Performance testing is the method of test and requirements used to ensure the product meets a minimum performance standard) Test Property Test Requirements Internal Use Cutlery Materials And Articles In Contact With Foodstuffs. Cutlery And Table Hollowware. Part 1. Requirements for cutlery for the preparation of food (Utensils for the preparation of food e.g. Knives with and without cutting edges, spatulas, palettes and carving forks) Materials And Articles In Contact With Foodstuffs. Cutlery And Table Hollowware. Requirements for stainless steel and silverplated cutlery Knife blocks Moisture Content (%) (For Solid Wood Only) Resistance to Corrosion (Applicable to Metal Components) Stability Test EN ISO EN ISO Standard Measure EN ISO 9227 Kitchen utensils, BBQ utensils Heat Resistance The sample shall comply the requirement of BS EN ISO contain following clauses Materials Construction Resistance of corrosion Strength of cutlery Firmness of handle attachment Hardness of knife blade Resistance Of Plastics Handles To Softening At Elevated Temperature Resistance Of Plastics Handles To Environment Stress Cracking Resistance Of Non-metal Handles To Distortion In Hot Water Resistance to dropping * Sharpness and edge retention Marking and labeling Must meet the requirements of the standard All solid wood components shall have the moisture content of 8-12%. Rating shall be at least 7 or above after salt spray test with 1%(For Indoor items) for 24 hrs. Concentration of salt solution shall be reported. The sample shall not overbalance on a 10-degree slope in all directions with or without gas cylinder. The cooking utensils shall withstand 150 C dry heat for 10 mins and 210 C wet heat in oil for 10 mins without structural damage or lose in function Page 2 of 3

7 Number JDW0047 Creation Date 1st May 2014 Revision No. V1.0 Revision Date Test Protocol Cutlery, knife blocks and kitchen utensils, BBQ utensils, dish drainer PERFORMANCE TESTING (Performance testing is the method of test and requirements used to ensure the product meets a minimum performance standard) Test Property Test Requirements Internal Use Handle Strength (if possible) Shall not detach or loosen after subjecting to appropriate tension and torque during actual use. Stain Resistance Drop Impact Test (Excluding glassware and/or ceramic) Dishwashing Test (If Applicable) Resistance to Corrosion (Applicable to Metal Components) Effects of Humidity EN ISO 9227 (Mod.) SGS In-house No objectionable stain by beverages and cooking mediums after 2 hours placement Beverages wine, grape juice, orange juice, coffee, tea (where applicable) Sample shall not produce any breakage, cracking or other abnormalities after 5 drops from a height of 30 onto a concrete floor. Shall withstand 10 cycles of dishwashing cycles at hot setting without visible damage or colour change Metal components shall sustain 1% salt spray (fog) without corrosion, rust or visible change, for a period of 24 hours. No visual change or failure - 24 hours at 95% RH and 38 C Dish drainer Loading test Actual Use Shall not damage after loaded with 5 kg for 24 hours Resistance to Corrosion (Applicable to Metal Components) Stability Test EN ISO 9227 Rating shall be at least 7 or above after salt spray test with 5% for 24 hrs. Concentration of salt solution shall be reported. The sample shall not overbalance on a 10-degree slope in all directions with or without gas cylinder. The Company s consulting services are governed by and subject to the SGS General Conditions of Service at http// SGS SA. All rights reserved Page 3 of 3

8 Number JDW0049 Creation Date 1 st May 2014 Revision No. V1.0 Revision Date Test Protocol Glass ware / Ceramicware / plastic ware REGULATORY REQUIREMENTS AND METHODS (Legal requirements are those stated in law that must be fulfilled) REACH Regulations, Article 67(1). (REACH Annex XVII) 1907/2006 and 1907/2006 and Article shall contain allowable amounts of restricted substances according to the conditions laid down in REACH Annex XVII. REACH Regulations, Article 33. General Products Safety Directive (GPSD) 1907/2006 and (Screening Test) Directive 2001/95/EC Articles containing substances of very high concern (SVHC) listed in the candidate list for authorisation > 0.1% w/w require communication in the supply chain. The product shall comply to the essential safety requirements of the GPSD(2001/95/EC). The manufacturer shall conduct and document a risk assessment of the product. The product must meet the essential safety requirement of the GPSD Packaging and Packaging Waste for environmental - Toxic Elements Tests on Packaging Material Persistent organic pollutants (POPs) Materials and articles in contact with food Regulations Directive 94/62/EC Acid digestion, analyzed by AAS or ICP-AES 850/2004 and Regulation 1935/2004 Must meet the requirements of European Directive 94/62/EC and its. The total toxic element content in the packaging material shall not exceed 0.01% by weight for Lead, Cadmium, Mercury & Hexavalent Chromium. Articles shall be free from Persistent organic pollutants (POPs) to the level set by the regulation. Materials and articles shall be manufactured in compliance with good manufacturing practice so that under normal or foreseeable conditions of use they do not transfer their constituents to food in quantities which could endanger human health, bring about an unacceptable change in the composition of the food or bring about deterioration in the organoleptic characteristics. Page 1 of 4

9 Number JDW0049 Creation Date 1 st May 2014 Revision No. V1.0 Revision Date Test Protocol Glass ware / Ceramicware / plastic ware PERFORMANCE TESTING (Performance testing is the method of test and requirements used to ensure the product meets a minimum performance standard) Test Property Test Requirements Internal Use GLASSWARE / CERAMIC WARE Rim & Handle Resistance (If Applicable) Handle temperature PLASTIC WARE Tensile Strength of Attachment Water Leakage Test Snap Fit Lid (If applicable) In house method INSULATED FLASKS AND JUGS Insulated Containers For BS EN Domestic Use Specification For Vacuum Ware, Insulated Flasks and Jugs The rim and handle shall withstand impact of 0.05J impact energy without visible damage or chipping. The handle temperature shall not exceed 66 C after the item has been tested in the microwave oven. Shall be no visible damage and loss of operation after pulling it at 90N. Shall withstand 24 hrs with 2/3 filled with water and no leakage. Snap fit lid shall fit onto product. Lid shall remain attached when cup is filled with liquid and inverted. The sample shall comply with the requirements of the standard including labeling & marking requirement of BS EN Page 2 of 4

10 Number JDW0049 Creation Date 1 st May 2014 Revision No. V1.0 Revision Date Test Protocol Glass ware / Ceramicware / plastic ware PERFORMANCE TESTING (Performance testing is the method of test and requirements used to ensure the product meets a minimum performance standard) Test Property Test Requirements Internal Use ADVISORY / RISK ASSESSMENT TESTS The following groups of tests may be requested by JD Williams to ensure compliance to the General Product Safety Directive (2001/95/EC) Dishwashing Test (If Claimed) 10 cycles no breakage, discolouration or adverse effects. Load in bottom rack Thermal Shock Test (For ceramic and glassware)) Stain Resistance (food ware) Stain Resistance (Drinkware) Drop Test (Non-Fragile Items) Microwave Safe Test (If Claimed) Durability of Rotating / Moving Components SGS-TM-HL SGS-TM-HL SGS-TM-HL unless claimed top loading only. It should not show damage due to testing, crazing, cracking, imperfections on the surface, structural, mechanical and functional damage should not be allowed after thermal shock Normal test parameter Dinnerware, 100 C(212 F); Oven and bake ware 230 C(480 F) No objectionable staining by after 2 hours placement Ketchup BBQ sauce Spaghetti sauce vinegar No objectionable staining by after 2 hours placement Red wine Coffee Chocolate Black tea Actual Use No breakage or separation - Withstand 3 drops from 3 feet. Shall withstand 3 cycles of microwave heating without visible damage or color Actual use change. Should provide good durability in use, 100 cycles with no damage or breakage. (Hinges, Locking Mechanism, Moving Parts, etc) (If Applicable) Stability Test (Applicable to Freestanding Items) Actual use The sample shall not overbalance on a 10 degree slope in all directions. The sample does not wobble when placed on a flat supporting surface. Page 3 of 4

11 Number JDW0049 Creation Date 1 st May 2014 Revision No. V1.0 Revision Date Test Protocol Glass ware / Ceramicware / plastic ware PERFORMANCE TESTING (Performance testing is the method of test and requirements used to ensure the product meets a minimum performance standard) Test Property Test Requirements Internal Use ADVISORY / RISK ASSESSMENT TESTS The following groups of tests may be requested by JD Williams to ensure compliance to the General Product Safety Directive (2001/95/EC) Handle Strength Shall not detach or loosen after subjecting to loading equivalent to 2 Handle / Knob Temperature (If applicable) Effects Of Heat Effects Of Cold Effects of hand washing if not dishwasher safe Lid security (coffee, tea pots) Pouring characteristics times of its capacity for 1 hour. Temperature of handle / knob should not exceed temperature limit below when distilled water of 95 is poured into the sample at room temperature. Handle material Temperature Limit metal 55 C plastics 70 C wood 89 C ceramic / glass / stone 66 C No visual change or failure after 24 hours at 100 deg C No visual change or failure after filling up with water and frozen at 0 deg C for 24 hours Shall exhibit no exterior surface degradation after being hand washed 5 times using a national brand liquid detergent at peak of 45 C, followed by rinse in cold water. The lids of lidded vessels intended for pouring liquids shall not separate from the body at an angle of less than 90 degrees Vessels intended to pour liquids shall pour in a single stream The Company s consulting services are governed by and subject to the SGS General Conditions of Service at http// SGS SA. All rights reserved Page 4 of 4

12 Oven and hob cookware Number JDW0050 Creation Date 1st May 2014 Revision No. V1.0 Revision Date REGULATORY REQUIREMENTS AND METHODS (Legal requirements are those stated in law that must be fulfilled) REACH Regulations, Article 67(1). (REACH Annex XVII) 1907/2006 and 1907/2006 and Article shall contain allowable amounts of restricted substances according to the conditions laid down in REACH Annex XVII. REACH Regulations, Article 33. General Products Safety Directive (GPSD) 1907/2006 and (Screening Test) Directive 2001/95/EC Articles containing substances of very high concern (SVHC) listed in the candidate list for authorisation > 0.1% w/w require communication in the supply chain. The product shall comply to the essential safety requirements of the GPSD(2001/95/EC). The manufacturer shall conduct and document a risk assessment of the product. The product must meet the essential safety requirement of the GPSD Packaging and Packaging Waste for environmental - Toxic Elements Tests on Packaging Material Persistent organic pollutants (POPs) General Requirements For All Food Contact Materials Directive 94/62/EC Acid digestion, analyzed by AAS or ICP-AES 850/2004 and 1935/2004 Must meet the requirements of European Directive 94/62/EC and its. The total toxic element content in the packaging material shall not exceed 0.01% by weight for Lead, Cadmium, Mercury & Hexavalent Chromium. Articles shall be free from Persistent organic pollutants (POPs) to the level set by the regulation. Articles shall comply to the essential requirements of the General Requirements For All Food Contact Materials 1935/2004 Page 1 of 3

13 Oven and hob cookware Number JDW0050 Creation Date 1st May 2014 Revision No. V1.0 Revision Date PERFORMANCE TESTING (Performance testing is the method of test and requirements used to ensure the product meets a minimum performance standard) Test Property Test Requirements Internal Use Cookware for use on top of a stove, cooker or hob Cookware Domestic Cookware For Use On Top Of A Stove, Cooker Or Hob (Exclude the clause of Coating on the body and the lid) Thermal shock test (applicable to glass lid) Abrasion Resistance Of Non-Stick Coating Adhesion Of Non-Stick Coating Scratch Resistance Of Non- Stick Coating Corrosion Resistance test of non-stick coating Non-Stick Coating Performance Test Resistance to Corrosion (Applicable to Metal Components) BS EN DD CEN/TS clause 7.2 as reference BS 7069 as reference / SGS In House BS 7069 as reference / SGS In House BS 7069 as reference / SGS In House BS 7069 as reference / SGS In House BS 7069 as reference / SGS In House EN ISO 9227 (Mod.) The sample shall comply the requirement of BS EN General Geometry Resistance to burning Heat resistance Torque resistance Bending strength Fatigue resistance Thermal hazards Pouring Base stability under shock conditions The glass lid should not damage when 10 pieces of samples are tested according to clause 7.2. There shall be no exposure of base metal after 250 cycles of abrasion There shall be no peeling of the non-stick coating after the test There shall be no exposure of base metal after the scratch test No visual change should be observed after test There shall be no trace of test foods and the surface shall be free from debris after wiping. Metal components shall sustain 1% salt spray (fog) without corrosion, rust or visible change, for a period of 24 hours. Page 2 of 3

14 Oven and hob cookware Number JDW0050 Creation Date 1st May 2014 Revision No. V1.0 Revision Date PERFORMANCE TESTING (Performance testing is the method of test and requirements used to ensure the product meets a minimum performance standard) Test Property Test Requirements Internal Use Oven ware for thermal ovens Cookware Ovenware For Use In Domestic thermal Ovens BS EN The sample shall comply the requirement of BS EN General Geometry Heat Resistance Fatigue Resistance Stability - Central Loading Stability - Eccentric Loading Stability - Tear Resistance (if applicable) Point of sale information Care and use instructions PERFORMANCE TESTING (Performance testing is the method of test and requirements used to ensure the product meets a minimum performance standard) Test Property Test Requirements Internal Use Additional testing The following groups of tests may be requested by JD Williams to ensure compliance to the General Product Safety Directive (2001/95/EC) Dishwashing Test SGS-TM-HL It should not show any damage due to testing, crazing, cracking, imperfections on the surface, fading of the glaze or paint, peeling of decal, discoloration of plastic ware, corrosion or tarnishing of metal ware should not be allowed. Normal test parameter 5 cycles at hot setting. The Company s consulting services are governed by and subject to the SGS General Conditions of Service at http// SGS SA. All rights reserved Page 3 of 3

15 Paper partyware Number JDW0055 Creation Date 1 st May 2014 Revision No. V1.0 Revision Date REGULATORY REQUIREMENTS AND METHODS (Legal requirements are those stated in law that must be fulfilled) REACH Regulations, Article 67(1). (REACH Annex XVII) 1907/2006 and 1907/2006 and Article shall contain allowable amounts of restricted substances according to the conditions laid down in REACH Annex XVII. REACH Regulations, Article 33. General Products Safety Directive (GPSD) 1907/2006 and (Screening Test) Directive 2001/95/EC Articles containing substances of very high concern (SVHC) listed in the candidate list for authorisation > 0.1% w/w require communication in the supply chain. The product shall comply to the essential safety requirements of the GPSD(2001/95/EC). The manufacturer shall conduct and document a risk assessment of the product. The product must meet the essential safety requirement of the GPSD Packaging and Packaging Waste for environmental - Toxic Elements Tests on Packaging Material Persistent organic pollutants (POPs) Materials and articles in contact with food Regulations Directive 94/62/EC Acid digestion, analyzed by AAS or ICP-AES 850/2004 and Regulation 1935/2004 Must meet the requirements of European Directive 94/62/EC and its. The total toxic element content in the packaging material shall not exceed 0.01% by weight for Lead, Cadmium, Mercury & Hexavalent Chromium. Articles shall be free from Persistent organic pollutants (POPs) to the level set by the regulation. Materials and articles shall be manufactured in compliance with good manufacturing practice so that under normal or foreseeable conditions of use they do not transfer their constituents to food in quantities which could endanger human health, bring about an unacceptable change in the composition of the food or bring about deterioration in the organoleptic characteristics. Page 1 of 2

16 Paper partyware Number JDW0055 Creation Date 1 st May 2014 Revision No. V1.0 Revision Date PERFORMANCE TESTING (Performance testing is the method of test and requirements used to ensure the product meets a minimum performance standard) Test Property Test Requirements Internal Use PLATES, BOWLS, CUPS, NAPKINS Determination of colour BS EN 646 Proc B Comply with standard fastness of dyed paper and board Colour fastness to BS EN ISO 105 No visible marking or loss of colour Spotting E07 Colour fastness to Water BS EN ISO 105 Grade 4 Colour Change Colour fastness to Rubbing Safety of Toys- Migration of certain elements E01 BS EN ISO 105 X12 EN71-3 PARTY BAGS, BANNERS, CONFETTI Safety of Toys- Physical and Mechanical Properties Safety of Toys- Flammability Safety of Toys- Migration of certain elements EN71-1 EN71-2 EN71-3 Grade 4 Staining Dry Grade 4 Wet Grade 3-4 This standard simulates a gastric extraction of accessible toys materials that might be ingested by a child. At the end of the extraction test, the levels of heavy elements are assessed to ensure they do not exceed the specified limits This part applies to all toys. Specifies requirements and methods of test for mechanical and physical properties of toys. Specifies the categories of flammable materials which are prohibited in all toys, and requirements concerning flammability of certain toys when they are subjected to a small source of ignition. This standard simulates a gastric extraction of accessible toys materials that might be ingested by a child. At the end of the extraction test, the levels of heavy elements are assessed to ensure they do not exceed the specified limits. Additional testing Test Property Test Requirements Internal Use Stability Test (Applicable to Freestanding Items) Actual use The sample shall not overbalance on a 10 degree slope in all directions. The sample does not wobble when placed on a flat supporting surface. The Company s consulting services are governed by and subject to the SGS General Conditions of Service at http// SGS SA. All rights reserved Page 2 of 2

17 Number JDW0051 Creation Date 1 st May 2014 Revision No. V1.0 Revision Date Test Protocol Storage Tins, Bread Bins, biscuit tins REGULATORY REQUIREMENTS AND METHODS (Legal requirements are those stated in law that must be fulfilled) REACH Regulations, Article 67(1). (REACH Annex XVII) 1907/2006 and 1907/2006 and Article shall contain allowable amounts of restricted substances according to the conditions laid down in REACH Annex XVII. REACH Regulations, Article 33. General Products Safety Directive (GPSD) Packaging and Packaging Waste for environmental - Toxic Elements Tests on Packaging Material Timber Regulation Obligations of operators who place timber and timber products on the market Persistent organic pollutants (POPs) General Requirements For All Food Contact Materials 1907/2006 and (Screening Test) Directive 2001/95/EC Directive 94/62/EC Acid digestion, analyzed by AAS or ICP-AES Regulation (EU) No 995/ /2004 and 1935/2004 Articles containing substances of very high concern (SVHC) listed in the candidate list for authorisation > 0.1% w/w require communication in the supply chain. The product shall comply with the essential safety requirements of the GPSD(2001/95/EC). The manufacturer shall conduct and document a risk assessment of the product. Must meet the requirements of European Directive 94/62/EC and its. The total toxic element content in the packaging material shall not exceed 0.01% by weight for Lead, Cadmium, Mercury & Hexavalent Chromium. The Regulation lays down the obligations of operators who place timber products on the internal market for the first time, as well as the obligations of traders Articles shall be free from Persistent organic pollutants (POPs) to the level set by the regulation. Articles shall comply to the essential requirements of the General Requirements For All Food Contact Materials 1935/2004 Page 1 of 2

18 Number JDW0051 Creation Date 1 st May 2014 Revision No. V1.0 Revision Date Test Protocol Storage Tins, Bread Bins, biscuit tins PERFORMANCE TESTING (Performance testing is the method of test and requirements used to ensure the product meets a minimum performance standard) Test Property Test Requirements Internal Use Resistance to Corrosion (Applicable to Metal Components) Stability Test (Applicable For Freestanding Items) Drop test (For non-fragile items) Cross Cut Adhesion (Metal Plating) Dishwashing Test (If Applicable) Sharp edges and sharp points Moisture Content (%) (For Solid Wood) EN ISO 9227 With Reference to ASTM D3359 SGS In-house EN 71 part reference Standard Measure Rating shall be at least 7 or above after salt spray test with 1%(For Indoor items) or 5%(For Outdoor items) respectively for 24 hrs. Concentration of salt solution shall be reported. The sample shall not overbalance on a 10 degrees slope in all directions. The sample does not wobble when placed on a flat supporting surface. Shall not have any damage after 3drops from a height of 3 feet (36 ) on a tiled floor Cut 2 in. cross hatch pattern on surface of plated item, plating must remain affixed Except silver-plated, aluminum and cast iron unless claimed to be dishwasher safe. 10 cycles no breakage or adverse effects. Load in bottom rack unless claimed top loading only. If failure, must include warning label on package if SGS deems appropriate. There shall be no sharp edges or points when tested to EN 71 part 1 sharp points and edges. All solid wood components shall have the moisture content of 8-12%. The Company s consulting services are governed by and subject to the SGS General Conditions of Service at http// SGS SA. All rights reserved Page 2 of 2

19 SPORTS, FITNESS & WELLBEING TABLE OF CONTENTS Adult & Children s Bicycles Bicycle helmets & Protective Clothes Free weights / Ab toner Wheelchairs & rollators Yoga / Pilates sets Page 1 of 1

20 Adult and children bicycle Number JDW0001 Creation Date 1 st May 2014 Revision No. V2.0 Revision Date 23 rd December 2015 REGULATORY REQUIREMENTS AND METHODS (Legal requirements are those stated in law that must be fulfilled) REACH Regulations, Article 67(1). (REACH Annex XVII) 1907/2006 and 1907/2006 and Article shall contain allowable amounts of restricted substances according to the conditions laid down in REACH Annex XVII. REACH Regulations, Article 33. General Products Safety Directive (GPSD) 1907/2006 and (Screening Test) Directive 2001/95/EC Articles containing substances of very high concern (SVHC) listed in the candidate list for authorisation > 0.1% w/w require communication in the supply chain. The product shall comply with the essential safety requirements of the GPSD(2001/95/EC). The manufacturer shall conduct and document a risk assessment of the product. The product must meet the essential safety requirement of the GPSD Packaging and Packaging Waste for environmental - Toxic Elements Tests on Packaging Material Persistent organic pollutants (POPs) Pedal bicycles safety regulations 2010 Directive 94/62/EC Acid digestion, analyzed by AAS or ICP-AES 850/2004 and SI 2010 No 198 Must meet the requirements of European Directive 94/62/EC and its. The total toxic element content in the packaging material shall not exceed 0.01% by weight for Lead, Cadmium, Mercury & Hexavalent Chromium. Articles shall be free from Persistent organic pollutants (POPs) to the level set by the regulation. The Pedal Bicycles Safety Regulations (PBSR) are intended to ensure that new bicycles are safe when sold. Includes provisions such as braking requirements, reflectors and a bell etc. Road vehicles lighting and goods vehicles (plating and testing)(amendment) Regulations 2009 SI 2009 No 3220 Front lamps must comply to BS or equivalent EC standard Rear lamps must conform to BS 3648 or BS or equivalent EC standard. Rear reflector must comply with BS Pedal reflectors must conform to BS Page 1 of 4

21 Adult and children bicycle Number JDW0001 Creation Date 1 st May 2014 Revision No. V2.0 Revision Date 23 rd December 2015 PERFORMANCE TESTING (Performance testing is the method of test and requirements used to ensure the product meets a minimum performance standard) Test Property Test Requirements Internal Use ADULT BICYCLE General Product Safety Directive (GPSD) General Product Safety Directive (GPSD) City and trekking, young adult, Mountain and racing Bicycles General Product Safety Directive (GPSD) General Product Safety Directive (GPSD) General Product Safety Directive (GPSD) General Product Safety Directive (GPSD) BS EN ISO Cycles Safety requirements for bicycles part 1 Terms and definitions BS EN ISO Cycles Safety requirements for bicycles Part 2 Requirements for City and Trekking, Young adult, mountain and racing bicycles BS EN ISO Cycles Safety requirements for bicycles Part 3 Common test methods BS EN ISO Cycles Safety requirements for bicycles Part 4 Braking test methods BS EN ISO Cycles Safety requirements for bicycles Part 5 Steering test methods BS EN ISO Cycles Safety requirements for The sample shall comply with the requirement of EN ISO , to satisfy the 2001/95/EC (GPSD) requirement The sample shall comply with the requirement of EN ISO , to satisfy the 2001/95/EC (GPSD) requirement The sample shall comply with the requirement of EN ISO , to satisfy the 2001/95/EC (GPSD) requirement The sample shall comply with the requirement of EN ISO , to satisfy the 2001/95/EC (GPSD) requirement The sample shall comply with the requirement of EN ISO , to satisfy the 2001/95/EC (GPSD) requirement The sample shall comply with the requirement of EN ISO , to satisfy the 2001/95/EC (GPSD) requirement Page 2 of 4

22 Adult and children bicycle Number JDW0001 Creation Date 1 st May 2014 Revision No. V2.0 Revision Date 23 rd December 2015 PERFORMANCE TESTING (Performance testing is the method of test and requirements used to ensure the product meets a minimum performance standard) Test Property Test Requirements Internal Use bicycles Part 6 Frame and fork test methods General Product Safety Directive (GPSD) General Product Safety Directive (GPSD) General Product Safety Directive (GPSD) General Product Safety Directive (GPSD) BMX Bicycles CHILDREN BICYCLE General Product Safety Directive (GPSD) Chlidren Bicycles BS EN ISO Cycles Safety requirements for bicycles Part 7 Wheels and rims test methods BS EN ISO Cycles Safety requirements for bicycles Part 8 Pedal and drive system test methods BS EN ISO Cycles Safety requirements for bicycles Part 9 Saddles and seat post test methods BS EN BMX bicycles Safety requirements and test methods BS EN ISO 8098 Bicycles for young children Safety requirements and test methods The sample shall comply with the requirement of EN ISO , to satisfy the 2001/95/EC (GPSD) requirement The sample shall comply with the requirement of EN ISO , to satisfy the 2001/95/EC (GPSD) requirement The sample shall comply with the requirement of EN ISO , to satisfy the 2001/95/EC (GPSD) requirement The sample shall comply with the requirement of EN 16054, to satisfy the 2001/95/EC (GPSD) requirement The sample shall comply with the requirement of EN ISO 8098, to satisfy the 2001/95/EC (GPSD) requirement Page 3 of 4

23 Adult and children bicycle Number JDW0001 Creation Date 1 st May 2014 Revision No. V2.0 Revision Date 23 rd December 2015 PERFORMANCE TESTING (Performance testing is the method of test and requirements used to ensure the product meets a minimum performance standard) Test Property Test Requirements Internal Use Additional testing Resistance to Corrosion (Applicable to Metal Components) Cross-Cut Adhesion Test (For Paint and Coating on Metal Part) EN ISO 9227 Rating shall be at least 7 or above after salt spray test with 1%(For Indoor items) or 5%(For Outdoor items) respectively for 24 hrs. Concentration of salt solution shall be reported. EN ISO 2409 Shall comply with Class 1 according to EN ISO The Company s consulting services are governed by and subject to the General Conditions of Service at http// SGS SA. All rights reserved Page 4 of 4

24 Number JDW0002 Creation Date 1 st May 2014 Revision No. V1.0 Revision Date Bicycle Helmet & Protective Clothes REGULATORY REQUIREMENTS AND METHODS (Legal requirements are those stated in law that must be fulfilled) REACH Regulations, Article 67(1). (REACH Annex XVII) 1907/2006 and 1907/2006 and Article shall contain allowable amounts of restricted substances according to the conditions laid down in REACH Annex XVII. REACH Regulations, Article 33. CE Certification PPE Directive Packaging and Packaging Waste for environmental - Toxic Elements Tests on Packaging Material Timber Regulation Obligations of operators who place timber and timber products on the market 1907/2006 and (Screening Test) Personal Protective Equipment Directive 89/686/EC. Directive 94/62/EC Acid digestion, analyzed by AAS or ICP-AES Regulation (EU) No 995/2010 Articles containing substances of very high concern (SVHC) listed in the candidate list for authorisation > 0.1% w/w require communication in the supply chain. Shall comply with requirements of Personal Protective Equipment Directive 89/686/EC. Type examination Must meet the requirements of European Directive 94/62/EC and its. The total toxic element content in the packaging material shall not exceed 0.01% by weight for Lead, Cadmium, Mercury & Hexavalent Chromium. The Regulation lays down the obligations of operators who place timber products on the internal market for the first time, as well as the obligations of traders Persistent organic pollutants (POPs) 850/2004 and Articles shall be free from Persistent organic pollutants (POPs) to the level set by the regulation. Page 1 of 3

25 Number JDW0002 Creation Date 1 st May 2014 Revision No. V1.0 Revision Date Bicycle Helmet & Protective Clothes ADVISORY / RISK ASSESSMENT TESTS The following groups of tests may be requested by JD Williams to ensure compliance to the General Product Safety Directive (2001/95/EC) PERFORMANCE TESTING (Performance testing is the method of test and requirements used to ensure the product meets a minimum performance standard) Test Property Test Requirements Internal Use Helmet for pedal cyclists Helmets for pedal cyclists and for users of skateboard and roller skates BS EN 1078 Shall comply with requirements of BS EN 1078 Type examination Protective clothing Protective clothing-- Wrist, palm, knee and elbow protectors for users of roller sports equipment BS EN Materials 4.2 Construction 4.3 Field of vision 4.4 Shock absorbing capacity 4.5 Durability 4.6 Retention system General Chin strap Fastening device Colour Strength Effectiveness Ease of release Shall comply with requirements of BS EN Type examination 5.1 General 5.2 Ergonomics 5.3 Innocuousness 5.4 Sizing 5.5 Restraint 5.6 Abrasion resistance 5.7 Impact strength 5.8 Impact performance for knee, palm and elbow protectors 5.9 Specific requirements for wrist protectors Page 2 of 3

26 Number JDW0002 Creation Date 1 st May 2014 Revision No. V1.0 Revision Date Bicycle Helmet & Protective Clothes ADVISORY / RISK ASSESSMENT TESTS The following groups of tests may be requested by JD Williams to ensure compliance to the General Product Safety Directive (2001/95/EC) PERFORMANCE TESTING (Performance testing is the method of test and requirements used to ensure the product meets a minimum performance standard) Test Property Test Requirements Internal Use Chromium VI content (Applicable for leather) EN 420 Should comply with the requirement in EN 420 Ph value Leather ISO 4045 Other material ISO 3071 Color fastness to ISO 105-E04 perspiration The quantity of Chromium VI in gloves containing leather shall not exceed 3.0 mg/kg when determined according to the test method described in EN ISO the ph value of protective clothing material should be greater than 3,5 and less than 9,5 Shall be at least grade 3 to 4 of the Grey scale for the color change of the specimen. The Company s consulting services are governed by and subject to the SGS General Conditions of Service at http// SGS SA. All rights reserved Page 3 of 3

27 Free weights,ab toners Number JDW0003 Creation Date Ist May 2014 Revision No. V1.0 Revision Date REGULATORY REQUIREMENTS AND METHODS (Legal requirements are those stated in law that must be fulfilled) REACH Regulations, Article 67(1). (REACH Annex XVII) 1907/2006 and 1907/2006 and Article shall contain allowable amounts of restricted substances according to the conditions laid down in REACH Annex XVII. REACH Regulations, Article 33. General Products Safety Directive (GPSD) 1907/2006 and (Screening Test) Directive 2001/95/EC Articles containing substances of very high concern (SVHC) listed in the candidate list for authorisation > 0.1% w/w require communication in the supply chain. The product shall comply with the essential safety requirements of the GPSD(2001/95/EC). The manufacturer shall conduct and document a risk assessment of the product. The product must meet the essential safety requirement of the GPSD Packaging and Packaging Waste for environmental - Toxic Elements Tests on Packaging Material Persistent organic pollutants (POPs) Directive 94/62/EC Acid digestion, analyzed by AAS or ICP-AES 850/2004 and Must meet the requirements of European Directive 94/62/EC and its. The total toxic element content in the packaging material shall not exceed 0.01% by weight for Lead, Cadmium, Mercury & Hexavalent Chromium. Articles shall be free from Persistent organic pollutants (POPs) to the level set by the regulation. Page 1 of 3

28 Free weights,ab toners Number JDW0003 Creation Date Ist May 2014 Revision No. V1.0 Revision Date PERFORMANCE TESTING (Performance testing is the method of test and requirements used to ensure the product meets a minimum performance standard) Test Property Test Requirements Internal Use Free weights Accuracy of weights Weight check All weights to weight within +/-3% of stated claim Locking clip or nut functionality Maximum load Strength training benches Stationary training equipment General safety requirements and test methods Stationary training equipment Strength training benches additional specific safety requirements and test methods AB Toners Functionality of Use Compression/Pull Strength test Slippage of open-end Handgrip SGS In-house SGS In-house EN ISO BS EN Visual check/actual use SGS In-house Locking clip or similar device shall prevent the fall out of mass plates from bar end when the bar is turned from horizontal to vertical in approximately 3 seconds and maintained at vertical position for 1 minute. Should meet maximum load claimed. Must meet the requirements of the standard. Must meet the requirements of the standard All aspects of the sample shall function properly as intended or claimed or stated in label with no performance defects. No deformation or crack under 1800N compression/pull for 1 minute over an area of not less than 6.5 cm 2 of the load supporting area The grip shall withstand an applied force of 90 N without movement in the direction of the applied force. ADVISORY / RISK ASSESSMENT TESTS Page 2 of 3

29 Free weights,ab toners Number JDW0003 Creation Date Ist May 2014 Revision No. V1.0 Revision Date The following groups of tests may be requested by JD Williams to ensure compliance to the General Product Safety Directive (2001/95/EC) Additional testing Test Property Test Requirements Internal Use Resistance to Corrosion (Applicable to Metal Components) Cross-Cut Adhesion Test (For Paint and Coating on Metal Part) EN ISO 9227 Rating shall be at least 7 or above after salt spray test with 1%(For Indoor items) or 5%(For Outdoor items) respectively for 24 hrs. Concentration of salt solution shall be reported. EN ISO 2409 Shall comply with Class 1 according to EN ISO The Company s consulting services are governed by and subject to the SGS General Conditions of Service at http// SGS SA. All rights reserved Page 3 of 3

30 Wheelchairs and Rollators Number JDW0004 Creation Date 1 st May 2014 Revision No. V1.0 Revision Date REGULATORY REQUIREMENTS AND METHODS (Legal requirements are those stated in law that must be fulfilled) REACH Regulations, Article 67(1). (REACH Annex XVII) 1907/2006 and 1907/2006 and Article shall contain allowable amounts of restricted substances according to the conditions laid down in REACH Annex XVII. REACH Regulations, Article 33. General Products Safety Directive (GPSD)(Rollators) Medical Devices Directive (wheelchairs) Packaging and Packaging Waste for environmental - Toxic Elements Tests on Packaging Material Timber Regulation Obligations of operators who place timber and timber products on the market Persistent organic pollutants (POPs) 1907/2006 and (Screening Test) Directive 2001/95/EC Directive 93/42/EEC Directive 94/62/EC Acid digestion, analyzed by AAS or ICP-AES Regulation (EU) No 995/ /2004 and Articles containing substances of very high concern (SVHC) listed in the candidate list for authorisation > 0.1% w/w require communication in the supply chain. The product shall comply with the essential safety requirements of the GPSD(2001/95/EC). The manufacturer shall conduct and document a risk assessment of the product. The product shall comply with the essential safety requirements of the Medical Devices Directive 93/42/EEC. Must meet the requirements of European Directive 94/62/EC and its. The total toxic element content in the packaging material shall not exceed 0.01% by weight for Lead, Cadmium, Mercury & Hexavalent Chromium. The Regulation lays down the obligations of operators who place timber products on the internal market for the first time, as well as the obligations of traders Articles shall be free from Persistent organic pollutants (POPs) to the level set by the regulation. Page 1 of 3

31 Wheelchairs and Rollators Number JDW0004 Creation Date 1 st May 2014 Revision No. V1.0 Revision Date PERFORMANCE TESTING (Performance testing is the method of test and requirements used to ensure the product meets a minimum performance standard) Test Property Test Requirements Internal Use WHEELCHAIRS Medical Devices Directive Manual wheelchairs requirements and test methods BS EN The sample shall comply to the requirements of EN to satisfy the 93/42/EEC Medical Device Directive requirement EN Design requirements 6.1 Foot supports, lower leg supports and arm supports 6.2 Pneumatic tyres 6.3 Fitting an anterior pelvic support 6.4 Wheelchairs for use as seats in motor vehicles 6.5 Braking systems 6.6 Component mass 6.7 Operations intended to be carried out by the occupant and / or assistant 6.8 Operator controls 6.9 Push handles and handgrips 7 Performance requirements 7.1 General 7.2 Foot supports, lower leg support assemblies and arm supports 7.3 Static, impact and fatigue strength 7.4 Braking system 7.5 Fatigue strength of manually operated parking brakes 7.6 Operating force 7.7 push handles and handgrips 7.8 Static stability 7.9 Surface temperature 7.10 Resistance to ignition 7.11 Seating adjustments for tilt and recline systems 7.12 Castor stem 7.13 Electrically powered ancillary equipment 7.14 Pushing force Page 2 of 3

32 Wheelchairs and Rollators Number JDW0004 Creation Date 1 st May 2014 Revision No. V1.0 Revision Date ROLLATORS Walking aids manipulated by both arm Requirements and test methods- EN ISO Shall comply with EN ISO Requirements 4.1 Manoeuvability 4.2 Stability 4.3 Brakes 4.4 Handgrip 4.5 Leg section and tip 4.6 Resting seat 4.7 Mechanical durability 4.8 Adjusting devices 4.9 Folding mechanism 4.10 Adjustment of handles 4.11 Material and finish 6. Information supplied by the manufacturer ADVISORY / RISK ASSESSMENT TESTS The following groups of tests may be requested by JD Williams to ensure compliance to the General Product Safety Directive (2001/95/EC) PERFORMANCE TESTING (Performance testing is the method of test and requirements used to ensure the product meets a minimum performance standard) Test Property Test Requirements Internal Use Resistance to Corrosion (Applicable to Metal Components) Abrasion Resistance BS EN ISO Colour fastness to Rubbing BS EN ISO 105 X12 Colour fastness to Water BS EN ISO 105 E01 Colour fastness to Light BS EN ISO 105 B02 Print durability EN ISO 9227 BS EN ISO BS EN ISO 105 X12 BS EN ISO 105 E01 BS EN ISO 105 B02 SGS In house method Rating shall be at least 7 or above after salt spray test with 1%(For Indoor items) or 5%(For Outdoor items) respectively for 24 hrs. Concentration of salt solution shall be reported. Minimum 25,000 cycles. Dry 4 Wet 3-4 Minimum Grade 4 Minimum Grade 4 Printed logos Grade 4 Shade Change, No significant change Wash at care label temp The Company s consulting services are governed by and subject to the SGS General Conditions of Service at http// SGS SA. All rights reserved Page 3 of 3

33 Yoga-pilates sets Number JDW0005 Creation Date 1 st May 2014 Revision No. V1.0 Revision Date REGULATORY REQUIREMENTS AND METHODS (Legal requirements are those stated in law that must be fulfilled) REACH Regulations, Article 67(1). (REACH Annex XVII) 1907/2006 and 1907/2006 and Article shall contain allowable amounts of restricted substances according to the conditions laid down in REACH Annex XVII. REACH Regulations, Article 33. General Products Safety Directive (GPSD) 1907/2006 and (Screening Test) Directive 2001/95/EC Articles containing substances of very high concern (SVHC) listed in the candidate list for authorisation > 0.1% w/w require communication in the supply chain. The product shall comply with the essential safety requirements of the GPSD(2001/95/EC). The manufacturer shall conduct and document a risk assessment of the product. The product must meet the essential safety requirement of the GPSD Packaging and Packaging Waste for environmental - Toxic Elements Tests on Packaging Material Persistent organic pollutants (POPs) Directive 94/62/EC Acid digestion, analyzed by AAS or ICP-AES 850/2004 and Must meet the requirements of European Directive 94/62/EC and its. The total toxic element content in the packaging material shall not exceed 0.01% by weight for Lead, Cadmium, Mercury & Hexavalent Chromium. Articles shall be free from Persistent organic pollutants (POPs) to the level set by the regulation. Textile fibres and related labeling and marking of the fibre composition of textile products Regulation 1007/2011 EU The composition and labeling of textile fibres shall comply with the requirements of the Regulation Page 1 of 3