Test Report No: EEC18/01 dated August 02, 2018

Transcription

1 Note: This report is issued subject to the Testing and Certification Regulations of the TÜV SÜD Group and the General Terms and Conditions of Business of TÜV SÜD PSB Pte Ltd. In addition, this report is governed by the terms set out within this report. Date Received : 17/07/2018 Test Period : 17/07/ /08/2018 Sample Description : 29 INCH BAR STOOL Color : ESPRESSO/BLACK WINTER GRAY/BLACK Buyer : / Product Type/ End Use : / Model/Style No. : Country Of Origin : MALAYSIA Country Of Destination : USA SKU No.: : / Manufacturer : Laboratory: TÜV SÜD PSB Pte. Ltd. No.1 Science Park Drive Singapore Phone : Fax : enquiries@tuv-sud-psb.sg Co. Reg : R Regional Head Office: TÜV SÜD Asia Pacific Pte. Ltd. 1 Science Park Drive, #02-01 Singapore Page 1 of 8

2 SAMPLE PHOTO Page 2 of 8

3 SUMMARY OF TEST RESULTS TEST REQUESTED TOTAL LEAD CONTENT IN SURFACE COATING EPA TSCA TITLE VI COMPOSITE WOOD HEAVY METAL IN PACKAGING FLAMMABILITY OF SOLID SHARP POINT AND SHARP EDGES WORKMANSHIP LEG STRENGTH BACKREST STRENGTH SEAT STATIC LOAD SEAT IMPACT FRONT STABILITY REAR STABILITY CONCLUSION For any concern or technical Inquiries, please contact SUZEN CHONG VICE PRESIDENT ASEAN SOFTLINE & HARDLINE Tel: PERFORMED BY: APPROVED BY: WONG KOK LEONG TEAM LEADER KOO CHIEH VOON HARDLINE PRODUCT MANAGER Page 3 of 8

4 TEST RESULT(S): Clause Method Criteria Result Rating Total lead in surface coating 16 CFR 1303/Consum er Product Safety Improvement Act of 2008 / CPSC-CH- E All accessible surface coatings in the assembled state on adult furniture [exempt factory applied coatings on metal components/parts] and household paint shall not contain lead or lead components in which the lead content is in exceed of 0.009% (90ppm) of the weight of the total content. In case of insufficient coating for testing found on number of samples specified in the protocol, vendor needs to provide dipped parts or components/parts for testing. Report actual results or include data table within report. Issue a program audit report. Component testing is allowed. Based on CPSC SOP, will composite up to 3 colors. If any color in the composite exceeds 80% of the limit (72 ppm), based on the lowest weight component, individual colors will be analyzed. (See Result in Page 7) Page 4 of 8

5 Clause Method Criteria Result Rating EPA TSCA Title VI Composite Wood 40 CFR (c) / 40 CFR (e) Finished goods containing regulated composite wood shall comply with the labeling requirements found in 40 CFR (c) unless the finished good qualities for the de minimis exception found in 40 CFR (e). A finished good does not require labeling per 40 CFR (c) if the finished good does qualiy for the de minimis excepting in 40 CFR (e). If the finished good does qualify for the de minimis exception, result is N/A. A finished good does require labeling 40 CFR (c) if the finished good does not qualify for the de minimis exception in 40 CFR (e). - At a minimum, the label must be on the product or the packaging - The label may be applied as a stamp, tag or sticker - The label shall include a minimum in legible English text: 1. Fabricator s name 2. Date the finished good was produced (in month/year) 3. A statement of compliance to denote that the finished good complied with TSCA Title VI Heavy metal in packaging Flammability of solid Sharp point and sharp edge Model Toxics in Packaging Legislation of the Toxics in Packaging Clearinghouse (TPCH) 16 CFR (c)(6)(v i) / 16 CFR CFR & 49 Example: XXX Company MM/YYYY EPA TSCA Title VI compliant for Formaldehyde Or California Phase 2 Compliant for Formaldehyde (until 22 March 2019) The sum of concentration levels of lead, cadmium, mercury and hexavalent chromium in packaging or packaging components shall not exceed 100 mg/kg (100 ppm) by weight. In lieu of testing, test report can be submitted if dated within One year. Shall not exceed the maximum allowable limit of no greater than 0.1 inches per second. Shall have no sharp points / edges, other than those required for function. Modification: Expanded scope to other products. (Mod) Workmanship Visual Shall have no discernible surface degradation, including crazing, shivering, denting, bubbles, cracks, stains, deformations, chips, fractures, heavy lines, waves, shear marks, scratches, scuff marks, indentations, or blisters.shall have no components missing, malformed, and/or fractured. (COC Provided) (Did not ignite) Page 5 of 8

6 Clause Method Criteria Result Rating Leg strength In-house No structural failure at the test load 75 lbf applied vertically to the leg at 1 in from the end of the leg for 1 minute. Force is applied in the front inward, side inward & back inward. Backrest In-house No failure at 150 lb. (non - tilt) and 200 lb. (tilt) for 1 strength test min. applied to 90 from back at 16 in. above the seat Seat static load In-house Apply a test load to seating area for 1 minute. Outdoor sample 400 lb Indoor sample 300 lb If the sample has more than one seating area, Two seating areas Simultaneously test on both seating areas Three seating areas Simultaneously test on one end seating area and the center seating area Four seating areas or more Simultaneously test on two adjacent seating areas followed by two adjacent center seating area Shall not have any permanent deformation larger than 1/4 in., loss of functionality or structural failure Seating impact In-house Shall have no structural breakage or greater than 1/2 in. permanent deformation after a free fall drop of a test load of 225 lb. to center of seating area with nontested seating areas loaded with 400 lb of static load. Dynamic loading shall be conducted on one point or consecutively; - on one seating area for one or two seaters - on one end seating area and the center area for three seaters. - on one end seating area and the center pair of seating area of four or more seaters. Front stability In-house The chair is obstructed by 1 In. bar in the front base, tipping force is measured in the 45 to the test platform. The tipping force shall not be less than 40% of the total chair weight. Rear stability In-house The chair shall not tip over when chair is loaded with 6 or 13 disks depending on type of chair. Apply a horizontal force to the highest disk.the location of the force application is 6 mm (0.25 in.) from the top of the disk. For chairs with seat height < 710 mm (28.0 in.), calculate the force as follows: F = (1195 H) Newton. H is the seat height in mm. [F = 1.1 (47 H) pounds force.]. H is the seat height in inches. For chairs with seat height equal to or greater than 710 mm (28.0 in.), a fixed force of 93 N (20.9 lbf.) shall be applied. (150 lbs load) (300 lbs load) Weight: 19.4 lbs Tipping force: 9.9 lbs Seat height: 30 3 /16 Force applied: 93N Page 6 of 8

7 TEST RESULT(S): (Continued) Total Lead Content in Surface Coating United States Consumer Product Safety Improvement Act (CPSIA), Section 101(a)(2) Test Method : CPSC-CH-E , analysis by Inductively Coupled Plasma - Optical Emission Spectrometer (ICP-OES). Test Item(s) Component Description(s) 1 Coating on gray chair 2 Coating on espresso chair 3 Black coating on swivel plate Maximum Allowable Limit : 90 mg/kg - Unit Result Test Item(s) Total Lead (Pb) mg/kg 8 ND 21 Conclusion - Note / Key : ND = Not Detected > = Greater than NR = Not Requested mg/kg = milligram(s) per kilogram NA = Not Applicable, due to no surface coating Detection Limit (mg/kg) : 5 Remark: - Page 7 of 8

8 Please note that this Report is issued under the following terms : 1. This report applies to the sample of the specific product/equipment given at the time of its testing/calibration. The results are not used to indicate or imply that they are applicable to other similar items. In addition, such results must not be used to indicate or imply that TÜV SÜD PSB approves, recommends or endorses the manufacturer, supplier or user of such product/equipment, or that TÜV SÜD PSB in any way guarantees the later performance of the product/equipment. Unless otherwise stated in this report, no tests were conducted to determine long term effects of using the specific product/equipment. 2. The sample/s mentioned in this report is/are submitted/supplied/manufactured by the Client. TÜV SÜD PSB therefore assumes no responsibility for the accuracy of information on the brand name, model number, origin of manufacture, consignment or any information supplied. 3. Nothing in this report shall be interpreted to mean that TÜV SÜD PSB has verified or ascertained any endorsement or marks from any other testing authority or bodies that may be found on that sample. 4. This report shall not be reproduced wholly or in parts and no reference shall be made by the Client to TÜV SÜD PSB or to the report or results furnished by TÜV SÜD PSB in any advertisements or sales promotion. 5. Unless otherwise stated, the tests were carried out in TÜV SÜD PSB Pte Ltd, No.1 Science Park Drive Singapore Page 8 of 8