DILLARD S TEST PROTOCOL FOR DILR US LUGGAGE (V26)

Transcription

1 Test Date: Reviewed By/Date: SUPPLEMENTAL PROTOCOLS DILLARD S TEST PROTOCOL FOR 1 The sample shall be reviewed against the requirements of California Proposition 65 to determine if additional testing or labeling is required. Note: Additional cost, sample size & TAT may be required if testing to 1 or more supplemental protocols is necessary. Please refer to the above referenced supplemental protocol(s) for additional information. LABELING One Time Use Products **Fair Packaging and Labeling Act OR Other Products **Uniform Packaging and Labeling Regulations F.P. & L. Act (16 CFR 500) OR NIST Uniform Laws and Regulations Handbook Manufacturer, Packer, or Distributor s Name & Address (City, State & Zip) Product Identification Net quantity of contents shall be expressed in terms of weight or mass, measure, numerical count, or combination so as to give accurate information to facilitate consumer comparison (U.S. and metric units). **Country of Origin Marking 19 CFR Shall indicate country of origin legibly, permanently, and in comparable size and close proximity to any mention of country other than country in which the article was manufactured or produced. Must be visible at point of purchase. Use Labeling Verify Label Claims ANALYTICAL *Total lead content in surface coatings * California Proposition 65 Applicable Section from Protocol CPSD-AN-PTCL US CPSC-CH-E / CPSD-AN Use/care instructions that are clear and understandable shall be provided in language appropriate to destination countries. Must comply to claims 1 accessible surface coatings on the product shall not contain lead or lead compounds in which the lead content is in excess of 0.06% (600 mg/kg) of the weight of the total content. PHYSICAL CHARACTERISTICS Dimensions (H x W) Total Depth Client requirement 1 Report overall depth; shall meet label claims Page 1 of 5

2 Handle Drop Shoulder Strap Drop Cir. Weight 1 Report overall weight; shall meet label claims Material Quality: Fabric weight ASTM D ae1 1 ± 3.0% from approval Fabric Count ASTM D ± 3.0% from approval Yarn Structure ASTM D (R2005) Material Defect ASTM D (R2016) Thickness Features: 1 ± 3.0% from approval 1 No critical / major defects No. of Main Compartments Visual 1 As claimed No. of Interior Pouches / Pockets Visual 1 As claimed No. of External Pouches / Pockets Visual 1 As claimed Other Features Visual 1 As claimed Parts Inventory CONSTRUCTION & WORKMANSHIP Sharp Points / Edges 16 CFR / Defects Workmanship PERFORMANCE 1 Report overall thickness; shall meet label claims 1 Shall meet label claims. Shall have no sharp points/edges, other than those required for function. Shall have no discernible surface degradation, including crazing, shivering, denting, bubbles, cracks, stains, deformations, chips, fractures, heavy lines, waves, shear marks, scratches, scuff marks, indentations, or blisters. Shall have no components missing, malformed, and/or fractured. Functionality TM-HL-0003 Shall function as intended as received Page 2 of 5

3 Strength Properties: Side Seam ASTM D e1 2 CRE Luggage Less Than Lbs/In (Min.), 24 And Up - 40 Lbs/In (Min.) Bottom Seam ASTM D e1 2 CRE Luggage Less than Lbs/In (Min.), 24 and up - 40 Lbs/In (Min.) Zipper Seam ASTM D e1 2 CRE Luggage Less than Lbs/In (Min.), 24 and up - 40 Lbs/In (Min.) Handle 45 ASTM D e1 2 CRE 2 Times stated loading capacity or 25 Lbs. if not stated Handle Strength ASTM D e1 2 CRE 2 Times stated loading capacity or 25 Lbs. if not stated Reinforced Stress Points ASTM D e1 2 CRE 25 Lbs./In. (Min.) Tensile Strength ASTM D (R2017) Snaps: 2 CRE 50 Lbs./In. (Min.) Attachment Strength S Lbs. for 10 seconds Snapping / Unsnapping Force ASTM D (R2016) Buttons: 2 Min. 2 Lbs Max. 8 Lbs Attachment Strength S Lbs. for 10 seconds modification = clamping device Impact Resistance S-1001 No fractures of button Zipper Performance: Operability (Open / Closed) ASTM D R CRE Max. 5 Lbs (Min.) Cross Widthwise Strength ASTM D R CRE 50 Lbs (Min.) Scoop Pull ASTM D R CRE 10 Lbs. (Min.) Top Stop ASTM D R CRE 20 Lbs (Min.) Bottom Stop ASTM D R CRE 20 Lbs (Min.) Colorfastness: Light AATCC [Option 3] Class 10 hours Page 3 of 5

4 Crocking AATCC 8 / Class 4.0(Dry)/ Class 3.0 (Wet) (Textile) Crockmeter AATCC Prints <6 ; AATCC 8 -Others; If Plaid Fails AATCC 8, Use AATCC 116 To ID Color Problem Static Wetting AATCC Class 4.0 (Min.) Atmospheric Fumes AATCC 23 1 Class 4.0 (Denim, PVC, Vinyl) Abrasion Resistance: Fabric ASTM D (R2017) Piping ASTM D a (R2015) (Stoll) Plastic Piping Durability: Resistance To Flexing Resistance To Cold Cracking CPSD-GB H-1008 & CPSD-GB Resistance to corrosion ASTM B modified / CPSD-HL Min. 500 cycles (C17 at 1000 gms.) 1 Min. 200 Cycles 1 Shall be no surface cracking within 5000 cycles flexing over a ¼ In. diameter mandrel 1 Shall be no surface cracking within 5000 cycles of flexing over a 1/4 In. diameter mandrel after 0 F for 4 hours. 1 [Applicable to samples / sample components constructed of metal or samples with metallic coatings that can be exposed to the environment] Shall withstand 24 hours in 1% salt spray (fog) with no noticeable oxidation / corrosion / visual changes. Effects of Humidity (Metal Components) Caster / Roller Performance: Rolling Performance Modification = 1% salt spray (fog). H No visual change after 24 95% RH & 100 F CPSD-GB Max. 3 Lbf. horizontal force is applied to move the fully loaded sample (50 Lb.) on smooth vinyl surface for a maximum of 10 seconds. No measurement is taken for the first 5 seconds of the test. The caster shall be oriented in a running direction throughout the test. Page 4 of 5

5 Durability of Roller Actual Use 1 Shall result in no adverse effects on rolling after use tests. (Rolling 4000 yds. on smooth concrete floor under 50 lbs. loading (distributed evenly) Note: tester stops every 200 yds.) Water And Stain Repellency: Surface Water Repellency AATCC Min. 80 ISO Rating Water Resistance AATCC 35 1 Min. Shower-Proof Rating (30 Sec. 2 Ft. Water) Oil Resistance AATCC Min. No. 5 Oil - Must Pass Locks - Operability Actual Use 1 Shall provide no problem in repeated use test (100 times) Key: * Additional Charge For This Test ** Mandatory Requirement Results Key: Rating Key: M Meets NM Does Not Meet Good Good NA Not Applicable NT Not Tested Fail Fail C Claimed R Recorded No. Of Required For Complete Testing: 2 Client Approval: SEPTEMBER 22, 2018/ Lucy Feng No. Of (Fully Packed) Cartons For Transit Testing: 2 (Only Upon Dillard s Request) Creation Date: May 21, 2002 No. Of Working Days For Complete Testing: 7 Editorial Revision Date: SEPTEMBER 19, 2018 Pricing Review Date: Technical Review Date: Page 5 of 5