M O TO R C YC L E S TA N D OWNER S MANUAL

Transcription

1 M O TO R C YC L E S TA N D OWNER S MANUAL WARNING: Read carefully and understand all INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury. Item #4885

2 Thank you very much for choosing a ULTRA-TOW Product! For future reference, please complete the owner s record below: Model: Purchase Date: Save the receipt, warranty and these instructions. It is important that you read the entire manual to become familiar with this product before you begin using it. This motorcycle stand is designed for certain applications only. The distributor cannot be responsible for issues arising from modification. We strongly recommend this stand not be modified and/or used for any application other than that for which it was designed. If you have any questions relative to a particular application, DO NOT use the stand until you have first contacted the distributor to determine if it can or should be performed on the product. For technical questions please call INTENDED USE This motorcycle stand with wheel chock and an adjustable wheel-locking system can accommodate front or rear motorcycle wheel sizes from 5in. to in. TECHNICAL SPECIFICATIONS Item Overall Dimensions Weight Capacity Wheel size Description 36in.L x 35 /4in.W x 6 /8in.H (9 x 90 x 4cm) 800 lbs. (86.5kg) 5in. to in. (38 to 56cm) GENERAL SAFETY RULES WARNING: Read and understand all instructions. Failure to follow all instructions listed below may result in serious injury. WARNING: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions or situations that could occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. SAVE THESE INSTRUCTIONS WORK AREA Keep the work area clean, free of clutter and well lit. Cluttered and dark work areas can cause accidents. Keep children and bystanders away while using this motorcycle stand. Distractions can result in a loss of control, so bystanders should be kept a safe distance from the work area. Page of 6

3 Be aware of all power lines, electrical circuits, water pipes and other mechanical hazards in your work area, particularly those hazards below the work surface hidden from the operator s view that may be unintentionally contacted and may cause personal harm or property damage. PERSONAL SAFETY Maintain a safe working environment. Make sure there is adequate surrounding workspace. Do not use this product in a damp or wet location. Use the correct product for your motorcycle. Make sure the motorcycle s wheel fits into the Wheel Chock prior to first use. USE AND CARE Use only the accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one model may create a risk of injury when used on another model. Never leave a motorcycle running while unattended. ASSEMBLY Measure the motorcycle wheel prior to assembly so that the Motorcycle Stand can be adjusted to fit the wheel length. The Motorcycle Stand will fit most standard motorcycles currently on the market. However, some models with especially wide tires or custom low-profile front fenders will not fit. Mount the Support Arm (4) to the front of the Base using Bolts (), Washers (5), and Nuts (6) Insert Pin (9) through the mounting holes and Cradle Stop (3); secure with Washer (0) and R Pin (). Insert Pin (9) through the mounting holes and Wheel Adapter (); secure with Washer (0) and R Pin (). Securely tighten all hardware before use. The Motorcycle Stand must be mounted securely to floor, trailer, truck bed or motorcycle lift before use. Mounting in Concrete Choose a location to install the Motorcycle Stand that is flat, level, and capable of bearing the combined weight of the Motorcycle Stand and the motorcycle being secured. The location should not obstruct walkways and provide enough room to retrieve the motorcycle after it is mounted. The surface of the location should be one suitable for the mounting of heavy equipment. Use the mounting holes in the Base () of the Stand as a template. Arrange the Base in the chosen location and mark where the holes are to be drilled. You will need concrete anchors (not included) to secure the Base to the concrete floor. Using the correct size concrete drill bit (not included), drill the mounting holes to secure the Base. Attach the concrete anchors to the floor. Secure the Base to the floor using concrete anchors NOTE: Do not sit on the motorcycle when it is loaded in the Motorcycle Stand. Page 3 of 6

4 Truck Bed Mounting Place the Base in the desired position on the mount location. Use the holes in the Base as a pattern to mark where to drill the holes for the hardware to mount the Stand. WARNING: Verify that the installation surface has no hidden wires, brake lines, etc. before drilling. Use a power drill (not included) and a steel cutting drill bit (not included) to drill holes in the mount location. Attach the Base to the mount location utilizing the appropriate hardware (not included). OPERATION WARNING: Do not drive motorcycle into the Motorcycle Stand. Select the correct mounting hole for the motorcycle being loaded on the Stand, and adjust the location of the Cradle Stop to fit the tire length properly. To load a motorcycle, lower the Wheel Adapter to the horizontal position and simply push the motorcycle into the Stand. The Wheel Adapter will close on the motorcycle tire, securing the bike in an upright position. The motorcycle should be secured with belts or straps (not included). To dismount the motorcycle, pull back firmly and steadily until the motorcycle rolls free of the Stand. MAINTENANCE Before each use, inspect the general condition of the Motorcycle Stand. Check for loose screws, poor alignment or binding of moving parts, cracked or broken parts, and any other condition that may affect its safe operation. Do not use damaged equipment. Occasionally, wipe the Motorcycle Stand down with soft cloth and mild detergent. Page 4 of 6

5 DIAGRAM & PARTS LIST Part# Description Qty. Part# Description Qty. Base 8 Eyelet Wheel Adapter 9 Pad 3 Cradle Stop 0 Pin 4 Support Arm Washer Dia. 4 5 Washer Dia.0 R-Pin 4 6 Nut M0 3 Bolt M0x45 For replacement parts and technical questions, please call Page5 of 6

6 WARRANTY One-Year Limited Warranty Distributed by Northern Tool + Equipment Co., Inc. Burnsville, MN Made in China Page 6 of 6