INSTRUCCIONES TECNICAS DE CAMPAÑA TUNDRA
|
|
- Mavis Robinson
- 5 years ago
- Views:
Transcription
1 INSTRUCCIONES TECNICAS DE CAMPAÑA TUNDRA PARA AIRBAG DE CORTINA
2 I. OPERATION FLOW CHART Verify Vehicle Eligibility 1. Check the VIN range. 2. Check the TIS Vehicle Inquiry System. Not Covered No further action required. Covered Inspect both the driver and passenger side B-pillar garnish for proper installation. NG Replace B-pillar garnish that did not pass the inspection OK OK Inspect the replaced B-pillar garnish for proper installation. NG Campaign completed, return the vehicle to the customer. Reattach the B-pillar garnish that did not pass the inspection II. IDENTIFICATION OF AFFECTED VEHICLES A. COVERED VIN RANGE Note: Although the involved vehicles are within the above VIN ranges, not all vehicles within these ranges were sold in your country. III. PREPARATION A. PARTS Parts are not required for all vehicles; it anticipated that very few vehicles will require parts. Trim color Part Number Part Name Qty/Unit Gray C040-B2 Center Pillar Garnish, RH C040-B2 Center Pillar Garnish, LH 1 Beige C040-E2 Center Pillar Garnish, RH C040-E2 Center Pillar Garnish, LH 1 B. TOOLS & EQUIPMENT Standard hand tools Protective Tape Flashlight Torque wrench Thickness gauge 2
3 IV. BACKGROUND The subject vehicles are equipped with side Curtain-Shield-Airbags (CSA) which deploy from the roof rails in the event of certain types of collisions. Due to the possible misinstallation of the upper tab of the B-pillar Upper Garnish, the garnish could interfere with the CSA in the event of a deployment. If the interference is sufficient, the CSA may not achieve its intended inflated shape. In some situations, this could increase the risk of injury to an occupant in the event of a crash. 3
4 V. B-PILLAR GARNISH INSTALLATION POSITION INSPECTION A. VEHICLE DISASSEMBLY AND PREPARATION These instructions describe the repair for one side, the same procedure should be used for the opposite side. 1. PULL WEATHERSTRIPPING AWAY FROM B-PILLAR a) Gently pull away the weather striping from the B-pillar for all four doors. 2. APPLY PROTECTIVE TAPE TO THE VEHICLES BODY a) Apply protective tape to the vehicles body as shown on all four doors to ensure the paint does not get scratched during the inspection process. B. GARNISH INSTALLATION POSITION INSPECTION 3. PREPARE THE THICKNESS GAUGE SET a) Stack Thickness gauges so that they are 2.0 mm (0.078 in) thick. b) Use tape to secure the Thickness gauge blades together NOTE: It may be necessary to reorganize the feeler gauge blade stack to ensure that the feeler gauge blades have no gap between them. 1. THERE ARE 2 INSPECTION LOCATIONS FOR EACH B-PILLAR GARNISH a) When inspecting the garnish position, you will need to check the two reinforcement ribs on either side of the garnish upper tab. Top view of garnish installed on a B-pillar Backside View of B-pillar Garnish 4
5 2. CHECK THE GAP BETWEEN THE BODY STRUCTURE AND THE B-PILLAR TAB REINFORMENT RIBS a) Using a small flashlight or pen light illuminate the back side of the garnish so you can locate the reinforcement ribs. b) From the front door check the clearnce between the B-pillar garnish tab reinforcement ribs and the body structure using the feeler gauge. c) From the rear door check the clearance between the B-pillar garnish tab reinforcement ribs and the body structure using the feeler gauge. d) Repeat the inspection on the other side of the vehicle. NOTE: From the rear door the SRS wire harness will need to be gently pushed out of the way to check the clearance. You must check the gap between the 2 ribs and the body structure; ensure that you are measuring at the correct location as shown. Please take care to do not apply any damage to SRS wire harness. Below are pictures of Good and NG conditions. Each position checked on the B-Pillar garnish must pass the criteria below. Good Condition (Extreme Close Up) (Feeler Gauge Interferes with ribs) Good Condition (Feeler Gauge fits with tension) NG Condition (Extreme Close Up) (Feeler Fits Loosely) Good Condition: Reinstall weatherstripping and return the vehicle to the customer. NG Condition: Procced to section VI for garnish replacement. 5
6 VI. REPLACE THE CENTER PILLAR GARNISH Replacement shall be performed for the center pillar garnish that was determined as unacceptable in the inspection. 1. TURN BACK THE FRONT & REAR DOOR OPENING TRIM WEATHERSTRIP 2. REMOVE THE FRONT & REAR DOOR SCUFF PLATE 3. DISCONNECT THE OUTER LAP BELT ANCHOR 4. REMOVE THE LOWER CENTER PILLAR GARNISH 5. REMOVE THE ASSIST GRIP 6. REMOVE THE CENTER PILLAR GARNISH After removing the bolt and clip at the bottom of the garnish, take care so as not to break the claw at the top of the center pillar garnish by forcibly moving it. a) Remove the bolt at the bottom of the center pillar garnish. b) Disengage the clip at the bottom of the center pillar garnish. c) Remove the claw at the top of the center pillar garnish. If replacing it with a NEW one, mark the old one, and then store it in a replacement parts box so that it will no longer be re-assembled. 7. INSTALL THE CENTER PILLAR GARNISH a) Move the seat belt to its topmost position on both garnish and seat belt sides to adjust the height of the shoulder portion of the seat belt. NOTE: Make sure that the garnish and the belt fit correctly by doing so. 6
7 b) Pass the front seat outer belt floor anchor through the center pillar garnish. NOTE: Do not twist the seat belt. c) Insert the claw at the top of a new center pillar garnish into a hole of the body. Make sure that the claw is inserted into the hole fully. d) Engage the clip at the bottom of the center pillar garnish. e) Attach a bolt at the bottom of the center pillar garnish. Torque: 5.5 N*m (56 kgf*cm, 49 in.*lbf) f) Reinstall the assist grip. Torque: 12 N*m (122 kgf*cm, 9 ft.*lbf) NOTE: Make sure that the claw of a cap is not protruded from the seating surface for mounting the assist grip. 8. CHECK IF THE CENTER PILLAR GARNISH IS RAISED a) Use the same procedure shown in Section V. CHECK IF THE CENTER PILLAR GARNISH IS RAISED, check if there is no gap between the garnish and the body. Note: If there is a gap, reattach the garnish. 9. REINSTALL THE LOWER CENTER PILLAR GARNISH 10. CONNECT THE OUTER LAP BELT ANCHOR Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf) 11. REINSTALL THE FRONT & REAR DOOR SCUFF PLATE 12. REINSTALL THE FRONT & REAR DOOR OPENING TRIM WEATHERSTRIP 13. CHECK THE OPERATION OF THE FRONT SEAT BELT a) Check if the seat belt is not twisted and it is able to be pulled out/rewinded smoothly. b) Check if the height of the shoulder portion of the seat belt is able to be adjusted smoothly. VII. APPENDIX A. CAMPAIGN PARTS DISPOSAL Make sure all campaign parts (original parts) removed from the vehicle are disposed of in a manner in which they will not be reused, unless requested for parts recovery return. 7
TECHNICAL INSTRUCTIONS FOR SPECIAL SERVICE CAMPAIGN 40F
TECHNICAL INSTRUCTIONS FOR SPECIAL SERVICE CAMPAIGN 40F 2002 THROUGH EARLY 2004 MODEL YEAR NORTH AMERICAN PRODUCED (NAP) TOYOTA CAMRY CURTAIN SIDE AIRBAG Page 1 of 26 I. OPERATION FLOW CHART Verify Vehicle
More informationREASSEMBLY IR INSTALL ROOF WIRE (a) Apply new double-sided tape to the roof headlining along the markings of the roof headlining.
31 REASSEMBLY 1. INSTALL ROOF WE (a) Apply new double-sided tape to the roof headlining along the markings of the roof headlining. Double-sided Tape Marking B130653E01 (b) NOTICE: Apply the tape securely
More informationSEAT BELT WARNING SYSTEM
SEAT BELT SEAT BELT WARNING SYSTEM 1 SEAT BELT WARNING SYSTEM System Name Power window control system (with Jam Protection Function) Sliding Roof System PRECAUTION When disconnecting the cable from the
More informationTECHNICAL INSTRUCTIONS FOR SAFETY RECALL E0G SUB HARNESS (FILTER) INSTALLATION
TECHNICAL INSTRUCTIONS FOR SAFETY RECALL E0G SUB HARNESS (FILTER) INSTALLATION 2003 2004 MODEL YEAR AVALON COLUMN MOUNTED SHIFT LEVER (FRONT BENCH SEAT) All dealership associates involved in the recall
More informationSEAT BELT WARNING SYSTEM
WARNING SYSTEM LOCATION WARNING SYSTEM 611 6105001 Combination Meter (Driver s Seat Belt Warning Lamp) Clock Assy (Passenger s Seat Belt Warning Lamp) Seat Belt Warning Sensor Front Seat Inner Belt Assy
More informationED 42. ENGINE HOOD / DOOR FRONT DOOR (w/o Power Window)
42 ENGINE HOOD / DOOR FRONT DOOR (w/o Power Window) (g) (h) Horizontally and vertically adjust the door by loosening the door side hinge bolts. Tighten the door side hinge bolts after the adjustment. Torque:
More informationREPLACEMENT. HINT: The installation procedures are the removal procedures in reverse order.
REPLACEMENT The installation procedures are the removal procedures in reverse order. 7615 7610301 1. REMOVE FRONT DOOR SCUFF PLATE RH (a) Using a screwdriver, disengage the 2 claws and 3 clips, and remove
More informationModel Year: 2008 Model: xb Doc ID: RM000001XUW004X
1 of 18 2/28/2008 10:41 AM Last Modified: 2-12-2007 Service Category: Vehicle Interior 1.6 A Section: Interior Panels/Trim Model Year: 2008 Model: xb Doc ID: RM000001XUW004X Title: INTERIOR: ROOF HEADLINING:
More informationTECHNICAL INSTRUCTIONS FOR NONCOMPLIANCE E0B SEAT HEATER ASSEMBLIES CERTAIN SIENNA
TECHNICAL INSTRUCTIONS FOR NONCOMPLIANCE E0B SEAT HEATER ASSEMBLIES CERTAIN 2013-2014 SIENNA I. OPERATION FLOW CHART The flow chart is for reference only. DO NOT use it in place of the full technical instructions.
More informationROOF HEADLINING ASSY EXTERIOR/INTERIOR TRIM 760VC 02 REPLACEMENT
REPLACEMENT 7627 The installation is in the reverse order of the removal. However, when there is a special point concerning the installation, it is indicated. On the LH side, use the same procedures as
More informationTECHNICAL INSTRUCTIONS FOR SAFETY RECALL C0T STEERING INTERMEDIATE EXTENSION SHAFT 2004 CERTAIN 2009 MODEL YEAR PRIUS
TECHNICAL INSTRUCTIONS FOR SAFETY RECALL C0T STEERING INTERMEDIATE EXTENSION SHAFT 2004 CERTAIN 2009 MODEL YEAR PRIUS I. OPERATION FLOW CHART II. IDENTIFICATION OF AFFECTED VEHICLES A. COVERED VIN RANGE
More informationREMOVAL IR 11. Slide the inner rear view mirror.
11 Slide REMOVAL CAUTION: Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (See page RS-1). 1. DISCONNECT
More informationRear Door: Service and Repair REAR DOOR
2007 Toyota Matrix L4-1.8L (1ZZ-FE) Copyright 2013, ALLDATA 10.52 Page 1 Rear Door: Service and Repair REAR DOOR Rear Door 2007 Toyota Matrix L4-1.8L (1ZZ-FE) Copyright 2013, ALLDATA 10.52 Page 2 ISASSEMBLY
More informationALLDATA Online Toyota Truck Tacoma 4WD V6-4.0L (1GR-FE) - Service and... Service and Repair 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Page 1 of 9 Service and Repair FRONT WIPER MOTOR REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. REMOVE FRONT WIPER ARM HEAD CAP a. Using a screwdriver wrapped with protective tape, remove
More informationSRS LIGHT "ON" - B0111/B OPEN SIDE SQUIB CIRCUIT TECHNICAL SERVICE BULLETIN Reference Number(s): T-SB , Date of Issue: June 23, 2010
SRS LIGHT "ON" - B0111/B0116 - OPEN SIDE SQUIB CIRCUIT -2006 Toyota Sienna... Page 1 of 27 SRS LIGHT "ON" - B0111/B0116 - OPEN SIDE SQUIB CIRCUIT TECHNICAL SERVICE BULLETIN Reference Number(s): T-SB-0162-10,
More informationDISASSEMBLY REASSEMBLY
4 EXTERIOR FRONT BUMPER DISASSEMBLY 1. REMOVE HOOD TO FRONT END PANEL SEAL (a) Using a clip remover, detach the 8 clips and remove the panel seal. 2. REMOVE FRONT BUMPER REINFORCEMENT (a) Using a clip
More informationRS 588 SUPPLEMENTAL RESTRAINT SYSTEM CURTAIN SHIELD AIRBAG ASSEMBLY REMOVAL
588 SUPPLEMENTAL RESTRAINT SYSTEM CURTAIN SHIELD AIRBAG ASSEMBLY REMOVAL 1. PRECAUTION 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL Wait for at least 90 seconds after disconnecting the cable to prevent
More informationTECHNICAL INSTRUCTIONS FRONT WIPER ARM NUTS REPLACEMENT
TECHNICAL INSTRUCTIONS RECALL CAMPAIGN SPECIAL SERVICE CAMPAIGN FRONT WIPER ARM NUTS REPLACEMENT IS250, IS300, IS350, IS200d, IS220d, IS250C, IS300C, IS350C IS F 1. OPERATION FLOW CHART ---------------------------------
More informationIR 13 INTERIOR ROOF HEADLINING REMOVAL
INTERIOR ROOF HEADLINING 13 REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. REMOVE REAR SEATBACK BOARD CARPET ASSEMBLY RH (See page SE-43) 3. REMOVE REAR SEATBACK ASSEMBLY RH (See page SE-43)
More informationED 13. ENGINE HOOD / DOOR FRONT DOOR (w/ Power Window) DISASSEMBLY
13 B088092E01 DISASSEMBLY Use the same procedures for both the LH and RH sides. 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH (a) Disengage the
More informationINTERIOR TRIM REMOVAL/INSTALLATION - PILLAR AREAS
2010 Honda Truck CR-V 4WD L4-2.4L Vehicle > Body and Frame > Interior Moulding / Trim > Trim Panel > Service and Repair > Removal and Replacement > Pillar Trim INTERIOR TRIM REMOVAL/INSTALLATION - PILLAR
More informationOT 1 OTHER SYSTEM POWER OUTLET SOCKET POWER OUTLET SOCKET COMPONENTS POWER OUTLET SOCKET ASSEMBLY SWITCH BASE POWER OUTLET SOCKET COVER B130929E02
POWER OUTLET SOCKET BODY HER ELECTRICAL SYSTEM COMPONENTS HER SYSTEM POWER OUTLET SOCKET 1 POWER OUTLET SOCKET SWITCH BASE POWER OUTLET SOCKET COVER B130929E02 2 HER SYSTEM POWER OUTLET SOCKET REMOVAL
More informationRS 413 SUPPLEMENTAL RESTRAINT SYSTEM CURTAIN SHIELD AIRBAG ASSEMBLY REMOVAL
413 REMOVAL Use the same procedures for the RH side and LH side. The procedures listed below are for the LH side. 1. PRECAUTION Be sure to read "PRECAUTION" thoroughly before servicing (See page -1). 2.
More informationConvertible Top Component Rattle
L-SB-0149-10 November 16, 2010 Service Category Vehicle Exterior Section Sliding Roof/Convertible Market USA Applicability YEAR(S) MODEL(S) ADDITIONAL INFORMATION 2010 IS250C, IS350C Introduction Some
More informationSTEERING SYSTEM PRECAUTION SR 1
System Name Power Window Control System STEERING COLUMN STEERING SYSTEM STEERING SYSTEM PRECAUTION 1 1. HANDLING PRECAUTIONS FOR S AIRBAG SYSTEM (SEE PAGE RS-1) 2. HANDLING PRECAUTIONS FOR STEERING COLUMN
More informationCOMPONENTS Toyota RAV ACCESSORIES & EQUIPMENT Front Seat - RAV4
2005 ACCESSORIES & EQUIPMENT Front Seat - RAV4 COMPONENTS Fig. 1: Identifying Front Seat Components & Torque Specifications FRONT SEAT ASSEMBLY REMOVAL CAUTION: Wear safety gloves, because the cutting
More informationLI 84 LIGHTING REAR COMBINATION LIGHT ASSEMBLY REMOVAL
84 GHTING REAR COMBINATION GHT ASSEMBLY REMOVAL HINT: Use the same procedure for both the RH and LH sides, unless otherwise specified. The procedure described below is for the LH side. 1. DISCONNECT CABLE
More informationSafety Belt Retractor and Pretensioner
SECTION 501-20A: Safety Belt System 2009 Mustang Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 12/03/2008 Safety Belt Retractor and Pretensioner Safety Belt Retractor and Pretensioner
More informationTECHNICAL INSTRUCTIONS
TECHNICAL INSTRUCTIONS DOOR SIDE AIRBAG SENSOR REPLACEMENT RX450h / RX350 / RX200t RX450h/RX350/RX200t Fr ドアエアバッグセンサ交換 一般 _v2.0 1 OPERATION FLOWCHART... 3 2 IDENTIFICATION OF AFFECTED VEHICLES... 4 3 PREPARATION...
More informationLEXUS CT 200h ILLUMINATED DOOR SILLS Preparation
Preparation Part Number: PT922-89100 Kit Contents Item # Quantity Req'd. Description 1 1 Door Sill, Front Right Hand 2 1 Door Sill, Front Left Hand 3 1 Door Sill, Rear Right Hand 4 1 Door Sill, Rear Left
More informationDISASSEMBLY. 1 of 9 2/28/ :48 AM 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. REMOVE FRONT DOOR ARMREST BASE UPPER PANEL
1 of 9 2/28/2008 10:48 AM Last Modified: 2-12-2007 1.6 A Service Category: Vehicle Exterior Section: Door/Hatch Model Year: 2008 Model: xb Doc ID: RM000001CE100DX Title: ENGINE HOOD / DOOR: FRONT DOOR:
More informationTECHNICAL INSTRUCTIONS
TECHNICAL INSTRUCTIONS RAV4 SPIRAL CABLE SUB-ASSEMBLY REPLACEMENT 1. OPERATION FLOW CHART --------------------------------- 3 2. IDENTIFICATION OF AFFECTED VEHICLES ---------- 4 3. PREPARATION --------------------------------------------------
More information2004 Toyota RAV ACCESSORIES/SAFETY EQUIPMENT Toyota - Air Bag Restraint Systems
DESCRIPTION & OPERATION 2004 ACCESSORIES/SAFETY EQUIPMENT Toyota - Air Bag Restraint Systems WARNING: Accidental air bag deployment is possible. Personal injury may result. Read and follow all WARNINGS
More informationTOYOTA YARIS XM SATELLITE RADIO Preparation (Sedan & Hatchback)
Preparation (Sedan & Hatchback) Part Number: Mounting Kit PT546-52096 Tuner Assy 86180-0W031 Tuner Assy Kit Contents (86180-0W031) Item # Quantity Reqd. Description 1 1 Tuner Assy, Stereo Component Mounting
More informationToyota Prius C 2015 Frameless EC Mirror w/ Compass & HomeLink
Toyota Prius C 2015 Frameless EC Mirror w/ Compass & HomeLink Part Number: 00016-05463 Accessory Code: ME4000 Note: This accessory requires replacement A-Pillar clip 62217-52120 to complete the installation
More informationSCION xa 2004 SATELLITE RADIO TUNER Section I Installation Preparation
Section I Installation Preparation Part Number: PT546 52040 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Satellite Tuner 2 1 Ground Cable 3 1 Tuner Cable 4 2 Tuner
More informationPage 1 of 33 SPECIFICATIONS 2013 Ford Edge 3.5L Eng Limited Print Date: TORQUE SPECIFICATIONS Description Nm lb-ft lb-in Assist handle bolts 9-80 B-pillar upper trim panel screw 9-80 C-pillar trim panel
More informationUPDATED SEPTEMBER 19, 2011
TECHNICAL INSTRUCTIONS FOR SPECIAL SERVICE CAMPAIGN 9LB REAR BRAKE CALIPER INSPECTION AND RUST REMOVAL 2006-2007 IS 250/350 2006-2007 GS 300/350/430/450h UPDATED SEPTEMBER 19, 2011 TECHNICAL INSTRUCTION
More informationTelescopic Lever Detent Clip Replacement
T-SB-0147-13 September 27, 2013 Service Category Steering Section Steering Column Market USA Applicability YEAR(S) MODEL(S) ADDITIONAL INFORMATION 2005 2012 Avalon SUPERSESSION NOTICE The information contained
More informationSPECIAL SERVICE CAMPAIGN (SSC) 10F ( MY ECHO AND AVALON TETHER ANCHOR UPGRADE)
TO: SUBJECT: ALL TOYOTA DEALER PRINCIPALS, SERVICE MANAGERS, PARTS MANAGERS SPECIAL SERVICE CAMPAIGN (SSC) 10F (2000-2001 MY ECHO AND AVALON TETHER ANCHOR UPGRADE) Toyota will initiate a Special Service
More informationTECHNICAL INSTRUCTIONS FOR LIMITED SERVICE CAMPAIGN (LSC) A0N HV WATER PUMP REPLACEMENT MODEL YEAR PRIUS
TECHNICAL INSTRUCTIONS FOR LIMITED SERVICE CAMPAIGN (LSC) A0N HV WATER PUMP REPLACEMENT 2004 2007 MODEL YEAR PRIUS I. OPERATION FLOWCHART II. IDENTIFICATION OF AFFECTED VEHICLES A. AFFECTED VIN RANGE Model
More informationWait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
2012 Camry DISASSEMBLY Hint: Report a problem with this article Use the same procedure for both the RH and LH sides. The procedure described below is for the LH side. PRECAUTION NOTICE: After turning the
More informationLEXUS GS 350/450h ILLUMINATED DOOR SILLS Preparation
Preparation Part Number: PT922-30120 (GS350) PT922-30130 (GS450h) NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents Item # Quantity Req'd. Description 1 1 Illuminated
More informationSRS AIRBAG Toyota RAV4. Supplemental Restraint System - RAV4 PRECAUTION CAUTION:
2005 RESTRAINTS Supplemental Restraint System - RAV4 SRS AIRBAG PRECAUTION CAUTION: The TOYOTA RAV4 is equipped with SRS that includes a driver airbag, front passenger airbag, side airbag and curtain shield
More information1. General Description
General Description 1. General Description A: COMPONENT (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (24) (23) (22) (21) (20) (19) (18) (17) (16) (15) (14) (13) (12) (11) AB-02007 (1) Curtain airbag module
More informationTECHNICAL INSTRUCTIONS
TECHNICAL INSTRUCTIONS PRADO SPIRAL CABLE SUB-ASSEMBLY REPLACEMENT 1. OPERATION FLOW CHART --------------------------------- 3 2. IDENTIFICATION OF AFFECTED VEHICLES ---------- 4 3. PREPARATION --------------------------------------------------
More informationOVERHAUL HINT: COMPONENTS: See page 74 49
7451 OVERHAUL COMPONENTS: See page 7449 7402R01 1. MOVE ROOF PANEL TO HALF Refer to the manual operation procedures, and halfopen the roof. H40336 A A:100 mm (3.94 in.) or less 2. REMOVE REAR SEAT CUSHION
More information75 5 ENGINE HOOD/DOOR
OVERHAUL Installation is in the reverse order of the removal. But the installation is indicated only when it has a point. In the RH side, work in the same procedure as in the LH side. 755 750DN01 1. REMOVE
More informationTOYOTA Yaris Hatchback EC REARVIEW MIRROR Preparation
Preparation Part Number: PT374-02090 Kit Contents Item # Quantity Reqd. Description 1 1 Auto Dimming Mirror Assembly w/ shift area light 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description
More informationTECHNICAL INSTRUCTIONS FOR SPECIAL SERVICE CAMPAIGN A7E ORIGINALLY SOLD IN AND CURRENTLY REGISTERED IN
TECHNICAL INSTRUCTIONS FOR SPECIAL SERVICE CAMPAIGN A7E ORIGINALLY SOLD IN AND CURRENTLY REGISTERED IN AL, AK, AZ, AR, CA, CO, FL, GA, HI, ID, IA, KS, LA, MS, MO, MT, NE, NV, NM, NC, ND, OK, OR, SC, SD,
More informationPart Number: PT
Preparation Part Number: PT374-02090 Kit Contents Item # Quantity Reqd. Description 1 1 Auto Dimming Mirror Assembly w/ shift area light 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description
More information1 of 13 2/10/ :41 AM
1 of 13 2/10/2017 10:41 AM Trim Removal/Installation - Pillar Areas Special Tools Required KTC trim tool set SOJATP2014 * *Available through the American Honda Tool and Equipment Program A-pillar Trim
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. DESCRIPTION: Auto-Dimming Mirror with Compass and Homelink 2. APPLICATION: Juke (2011) 3. PART NUMBER: 999L1 VW002 4. KIT CONTENTS: Item Qty Description Service
More informationFRONT BUMPER COMPONENTS. Front Bumper Side. Mounting Bracket RH. Front Bumper. Reinforcement. Front Bumper Side. Mounting Bracket LH
761 FRONT BUMPER FRONT BUMPER COMPONENTS 760HX02 Front Bumper Side Mounting Bracket RH Front Bumper Reinforcement 36 (367, 27) Front Bumper Side Mounting Bracket LH 36 (367, 27) 5.0 (51, 44 in. lbf) Front
More informationON-VEHICLE INSPECTION
51 Connector Front Side: A5 ON-VEHICLE INSPECTION 1. INSPECT TOWING CONVERTER RELAY (a) Measure the voltage and check the result in accordance with the value(s) in the table below. Standard E064833E01
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: KIT CONTENTS: Illuminated Kick Plate Maxima (Applicable ONLY to U.S. Market Vehicles with Build Date June 2012 or later) 999G6
More informationAll bolts, screws and nuts relevant to installing and removing the instrument panel are shown along with their alphabet code below.
Page 1 of 12 Last Modified: 9-21-2007 1.6 A Service Category: Vehicle Interior Section: Interior Panels/Trim Model Year: 2008 Model: Tundra Doc ID: RM000002VHU003X Title: INSTRUMENT PANEL: INSTRUMENT PANEL
More informationTECHNICAL INSTRUCTIONS
TECHNICAL INSTRUCTIONS REPLACEMENT THE STEERING INTERMEDIATE SHAFT ASSEMBLY FJ CRUISER For LHD 1 OPERATION FLOWCHART... 3 2 IDENTIFICATION OF AFFECTED VEHICLES... 4 3 PREPARATION... 5 4 GENERAL DESCRIPTION...
More informationSEAT BELTS SECTION CONTENTS H RESTRAINTS SB-1
H RESTRAINTS A SECTION SEAT BELTS B C D CONTENTS E PRECAUTIONS... 2 Precautions for Supplemental Restraint System (SRS) AIR BAG and SEAT BELT PRE-TEN- SIONER... 2 Precaution for Seat Belt Service... 2
More informationOVERHAUL. 1. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH (a) Using a screwdriver, remove the lower frame bracket garnish.
OVERHAUL The installation is in the reverse order of the removal. However, when there is a special point concerning the installation, it is indicated. On the RH side, use the same procedures as on the
More informationTECHNICIAN SAFETY INFORMATION
2009 Honda Accord L4-2.4L Vehicle > Restraints and Safety Systems > Air Bag Systems > Service Precautions TECHNICIAN SAFETY INFORMATION SRS Precautions and Procedures General Precautions NOTE: Some systems
More informationINSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 38143-40201 S 2008 ODYSSEY Issue Date AUG 2008 PARTS LIST Backup Sensor Attachment Kit P/N 08V67-SHJ-100B Backup sensor control unit
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
Important: Read Before Installation *550-0022-000* 550-0022AAA Dealer Installation Recommended. To avoid serious personal injury or property damage, obtain the Installation Instructions before attempting
More informationPOWER WINDOW CONTROL SYSTEM
POWER WINDOW CONTROL SYSTEM ONVEHICLE INSPECTION POWER WINDOW CONTROL SYSTEM 1. CHECK POWER WINDOW (MANUAL OPERATION FUNCTION) (a) Turn the ignition switch ON. (b) Check that the door glass will rise when
More informationDISPOSAL. CAUTION: Never dispose of front seat outer belt which has an inactivated. activated pretensioner.
DISPOSAL When scrapping vehicles epuipped with a seat belt pretensioner or disposing of a front seat outer belt (with seat belt pretensioner) always first active the seat belt pretensioner in accordance
More informationTOYOTA COROLLA EC REARVIEW MIRROR Preparation
Preparation Part Number: PT374-02090 Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly w/ PRNDL 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description 1 2 T-tap Connectors,
More informationConf licts Note: TOYOTA Tacoma 2016 LED Illumination Package (Interior and Exterior) Part Number: Accessory Code: LL1000.
TOYOTA Tacoma 2016 LED Illumination Package (Interior and Exterior) Part Number: 00016-00069 Accessory Code: LL1000 Conf licts Note: Color Applicability/Trim Level Kit Contents Item # Quantity R eqd. Description
More informationTOYOTA RAV TRAILER WIRE HARNESS Preparation
Preparation Part Number: PU322-42013-UW Kit Contents Item # Qty Description 1 1 Trailer Module Harness 2 1 Trailer 4-Flat Harness 3 1 Trailer Power Wire Harness 4 1 Mounting Bracket, 4-Flat 5 2 Screw #10-24
More informationTOYOTA FJ CRUISER AIR DAM/LIGHT BAR Preparation
Preparation Part Number: PT278-35071 Kit Contents Item # Quantity Reqd. Description 1 1 Air Dam / Light Bar Hardware Bag 1 Contents Item # Quantity Reqd. Description 1 2 Screw, M6x33mm, Wafer Head 2 2
More informationMUSTANG TIGER CAGE INSTRUCTIONS MANUAL PAGE 1
2005-2011 MUSTANG TIGER CAGE INSTRUCTIONS MANUAL PAGE 1 Thank you for purchasing our 2005-2011 Mustang Tiger Cage. Please read through all of the instructions first and then start installing the kit. We
More informationSCION xb 2004 SATELLITE RADIO TUNER Section I Installation Preparation
Section I Installation Preparation Part Number: PT546 52040 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Satellite Tuner 2 1 Ground Cable 3 1 Tuner Cable 4 2 Tuner
More informationToyota Yaris 2015 Frameless EC Mirror w/ Compass & HomeLink
Toyota Yaris 2015 Frameless EC Mirror w/ Compass & HomeLink Part Number: 00016-05463 Accessory Code: ME4000 Note: This accessory requires replacement A-Pillar clip 62217-52070 to complete the installation
More informationTECHNICAL INSTRUCTIONS FOR SPECIAL SERVICE CAMPAIGN 40L 2004 PRIUS BRAKE LIGHT SWITCH REPLACEMENT
TECHNICAL INSTRUCTIONS FOR SPECIAL SERVICE CAMPAIGN 40L 2004 PRIUS BRAKE LIGHT SWITCH REPLACEMENT I. OPERATION FLOW CHART Verify Vehicle Eligibility 1. Check VIN range. 2. Check for SSC 40L Completion
More information1. General Description
EXERIOR/INERIOR RIM 1. General Description A: COMPONEN 1. FRON GRILLE General Description EI-00627 Front grille Front grille emblem Front grille clip 2. UNDER COVER EI-00681 ightening torque: N m (kgf-m,
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: KIT-CARBON FIBER REAR SPOILER INFINITI Q50 T99J1 J5000 KIT CONTENTS: Item A B C D Qty. 1 4 1 1 Part Description Spoiler Assembly
More informationARTICLE BEGINNING COMPONENTS FRONT DOOR Toyota Tacoma
Page 1 of 17 ARTICLE BEGINNING COMPONENTS Page 2 of 17 Fig. 1: Front Door Components (w/o Power Door Lock & Power Window Regulator) Page 3 of 17 Fig. 2: Front Door Components (W/ Power Door Lock & Power
More informationTechnical Service BULLETIN
Technical Service BULLETIN December 22, 2007 Title: Models: 08 Scion xb BO022-07 BODY Introduction Some customers may experience a condition where the left hand upper cowl reinforcement cover may become
More informationSCION xb EC REARVIEW MIRROR Preparation
Preparation Part Number: PT374-02090 Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly w/ PRNDL 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description 1 2 T-tap Connectors,
More informationAirbags, servicing. Airbag system, safety precautions WARNING!
Page 1 of 75 69-40 Airbags, servicing Airbag system, safety precautions Checking, removing, installing and servicing may ONLY be performed by qualified personnel. Never perform tests using a test light
More informationPOWER MIRROR CONTROL SYSTEM
RROR POWER RROR CONTROL SYSTEM POWER RROR CONTROL SYSTEM BODY RROR PARTS LOCATION 1 DRIVER SIDE JUNCTION BLOCK - ACC FUSE - AM2 FUSE - ACC-B FUSE OUTER REAR VIEW RROR RH OUTER REAR VIEW RROR LH ACC RELAY
More informationSCION xb AUTO-DIMMING MIRROR Preparation
Preparation Part Number: PT374-02090 Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly w/ PRNDL 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description 1 2 T-tap Connectors,
More information2/26/2018 Seating - Seat - Front - Removal and Installation 2010 Ford F-150 MotoLogic Seating 2010 F-150
2010 F-150 Report a problem with this article 501-10 Seating 2010 F-150 REMOVAL AND INSTALLATION Procedure revision date: 07/01/2009 Driver Seat Seat Front NOTE: Refer to the installation steps for tightening
More informationWIPER AND WASHER SYSTEM
WIPER AND WASHER WIPER AND WASHER SYSTEM WIPER AND WASHER SYSTEM PRECAUTION 1 NOTICE: When disconnecting the cable from the negative (-) battery terminal, initialize the following systems after the cable
More informationPrius XM Radio Installation Instructions. Eddie Bell
2004-2005 Prius XM Radio Installation Instructions By Eddie Bell www.metrotpn.com 1 Let me begin by saying this is an easy but time consuming job. Set aside a few hours of your time for the install. If
More informationPart Number: TCA-712SE
Date: 09.04.2013 TOYOTA CAMRY SE 2012-14 LED DRL Part Number: TCA-712SE Kit Contents Item # Quantity Reqd. Description 1 2 DRL s bezels w/led DRL 2 1 Driver Box 3 1 Harness bag 4 1 User s card 5 1 Cushion
More information2010 to 2013 Toyota 4runner Rear bumper installation instructions:
2010 to 2013 Toyota 4runner Rear bumper installation instructions: Note: This is one of the most difficult bumpers we product to install. The installation of this bumper requires cutting of the current
More informationTECHNICAL INSTRUCTIONS FOR SAFETY RECALL B0M CRANKSHAFT PULLEY REPLACEMENT CERTAIN 2004 MODEL YEAR AVALON
TECHNICAL INSTRUCTIONS FOR SAFETY RECALL B0M CRANKSHAFT PULLEY REPLACEMENT CERTAIN 2004 MODEL YEAR AVALON CERTAIN 2004 2005 MODEL YEAR CAMRY, CAMRY SOLARA, HIGHLANDER, SIENNA CERTAIN 2006 MODEL YEAR HIGHLANDER
More information2014 Subaru of America, Inc. All rights reserved. SERVICE BULLETIN. Service Procedure to Address a Wind Rushing Sound from the Front Door Sash Area
ATTENTION: GENERAL MANAGER q PARTS MANAGER q CLAIMS PERSONNEL q SERVICE MANAGER q IMPORTANT - All Service Personnel Should Read and Initial in the boxes provided, right. 2014 Subaru of America, Inc. All
More information3rd Row Seat Rear Leg Latch Squeak/Rattle - Manual Seat Only
T-SB-0147-14 November 19, 2014 3rd Row Seat Rear Leg Latch Squeak/Rattle - Manual Seat Only Service Category Vehicle Interior Section Seat Market USA Applicability YEAR(S) MODEL(S) ADDITIONAL INFORMATION
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory ACCESSORY HANDSFREELINK Application 2010 ACCORD 2 AND 4-DOOR Publications No. AII 42231 Issue Date AUG 2009 PARTS LIST HFL retainer HFL Attachment Kit P/N 08E02-TA0-100
More informationInstallation Manual: Honda CRV Power Lift Gate System
Installation Manual: Honda CRV Power Lift Gate System Page 1 of 18 NOTE: Installation Precaution 1. It is recommended to have this product installed by a professional to avoid damage caused by improper
More informationTECHNICAL INSTRUCTIONS FOR SAFETY RECALL D0H BRAKE BOOSTER PUMP ASSEMBLY (ACCUMULATOR) CERTAIN 2010 MODEL YEAR PRIUS
TECHNICAL INSTRUCTIONS FOR SAFETY RECALL D0H BRAKE BOOSTER PUMP ASSEMBLY (ACCUMULATOR) CERTAIN 2010 MODEL YEAR PRIUS Complete D0H Technical Video Supplement I. OPERATION FLOW CHART The flow chart is for
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Accessory Hands Free Link Application 2008 ACCORD 2 AND 4-DOOR Publications No. AII 38281 Issue Date NOV 2007 PARTS LIST Attachment Kit P/N 08E02-TA0-100 trim retainer
More informationSEAT BELTS SECTION CONTENTS H RESTRAINTS SB-1
H RESTRAINTS A SECTION SEAT BELTS B C D CONTENTS E PRECAUTIONS... 2 Precautions for Supplemental Restraint System (SRS) AIR BAG and SEAT BELT PRE-TEN- SIONER... 2 Precaution for Seat Belt Service... 2
More informationTOYOTA PRIUS C FOG LIGHT (Halogen & LED)
TOYOTA PRIUS C 2012-14 FOG LIGHT (Halogen & LED) Part Number: TPC-312 / TPC-812 Kit Contents Item # Quantity Reqd. Description 1 2 Fog Lamps 2 2 Bezels 3 1 Switch Assembly 4 1 Fog Light Operation guide
More informationREASSEMBLY SE INSTALL REAR SEATBACK LOCK ASSEMBLY (a) Install the rear seatback lock with the 2 bolts. Torque: 18 N*m (185 kgf*cm, 13 ft.
AT REAR AT ASMBLY (for RH Side) 49 REASMBLY CAUTION: Wear protective gloves. Sharp surfaces on the rear seat cushion frame and the rear seatback frame could cause injuries to your hands. 1. INSTALL REAR
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. 3RD ROW P/N 08R12-SHJ-100 2006 ODYSSEY AII 30563-31117 Issue Date OCT 2005 PARTS LIST Left side rear sunshade Driver s Side 1. Remove the
More informationSUPPLEMENTAL RESTRAINT SYSTEM (SRS)
RESTRAINTS SECTION SRS A SUPPLEMENTAL RESTRAINT SYSTEM (SRS) B C D CONTENTS E PRECAUTION... 2 PRECAUTIONS... 2 Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TEN- SIONER"...2
More informationSEAT BELT SECTION SB CONTENTS RESTRAINTS SB-1 PRECAUTION... 2 ON-VEHICLE REPAIR... 3
RESTRAINTS SECTION SB A SEAT BELT B C D CONTENTS E PRECAUTION... 2 PRECAUTIONS... 2 Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TEN- SIONER"...2 Precaution for Seat
More informationTOYOTA PRIUS XM SATELLITE RADIO Preparation
Preparation Part Number: Mounting Kit PT546-4700 Tuner Assy 8680-0W03 NOTE: Part number of this accessory may not be the same as the part number shown. Tuner Assembly Kit Contents (8680-0W03) Item # Quantity
More information