DTG Commercial. 3-5 Tons Gas/ Electric Units Up to 15.5 SEER and 13.0 EER Up to 81% AFUE

Transcription

1 DT ommercial 5 Tons as/ Electric Units Up to 5.5 SEE and.0 EE Up to 8% AFUE ooling apacity: 5,600 60,000 BTU/h Heating apacity: 6,000 8,000 BTU/h ontents Nomenclature... Product Specifications... Expanded ooling Data...6 Airflow Data...8 rankcase Heater... Electrical Data... Dimensions... iring Diagrams...7 for Models with DD ontrols...7 Accessories...8 Standard Features Patented tubular heat exchange Highefficiency scroll compressor opper tube/aluminum fin coils High and lowpressure switches ontactor with lugs Highcapacity, steelcased filter drier volt terminal strip onvertible airflow orientation Easy to service Builtin filter rack with standard filters Bottom utility entry omplies with alifornia Low NOx emissions standards AHI ertified; ETL Listed phase unit meets the performance specified as of //05 in Table 6.8. of ASHAE Standard 90.0 abinet Features Heavygauge, galvanizedsteel cabinet with UVresistant powderpaint finish Full Perimeter ail Sloped drain pan * omplete warranty details available from your local distributor or manufacturer s representative or at SSDT /8 Supersedes /7

2 Nomenclature D T V * * * A *,5,6 7,8, evision Levels Major & Minor Brand FactoryInstalled Options D Daikin X No Options A Nonpowered convenience outlet onfiguration B Powered convenience outlet Standard Efficiency (6 5 Tons) Lowambient kit S Standard Efficiency ( 5 Tons) D eturn air smoke detector T High Efficiency ( 5 Tons) E Supply air smoke detector F Nonpowered convenience outlet; Application Lowambient kit ooling Nonpowered convenience outlet; as Heat eturn air smoke detector H Heat Pump H Nonpowered convenience outlet; Supply air smoke detector Nominal ooling apacity J Nonpowered convenience outlet; 06 Tons 0 8½ Tons 00 5 Tons eturn & Supply air smoke detectors 08 Tons 0 0 Tons K Nonpowered convenience outlet; Tons 50 ½ tons Lowambient kit; Supply air smoke detector 07 6 Tons 80 5 Tons L Nonpowered convenience outlet; 090 7½ Tons 0 0 Tons Lowambient kit eturn & Supply air smoke detectors Nominal Heating apacity M Powered convenience outlet; as/electric A/ H/P FactoryInstalled Electric Heat Lowambient kit 05 5,000 BTU/h XXX No Heat N Powered convenience outlet; ,000 BTU/h 00 0 k 00 0 k eturn air smoke detector 5 5,000 BTU/h 05 5 k 0 0 k O Powered convenience outlet; 0 0,000 BTU/h 06 5 k 05 5 k eturn & Supply air smoke detectors 0 0,000 BTU/h 08 8 k 06 5 k P Powered convenience outlet; 50 50,000 BTU/h 00 0 k k Supply air smoke detector 00 00,000 BTU/h 05 5 k Q Powered convenience outlet; Lowambient See product specifications for heat size(s) available for each capacity. kit; eturn air smoke detector Powered convenience outlet; Lowambient Voltage kit; Supply air smoke detector 080//60 (DS* & DT* 5 Tons models only) 60//60 T Powered convenience outlet; Lowambient 080// //60 kit; eturn & Supply air smoke detectors U Nonpowered convenience outlet; Supply Fan/Drive Type/Motor Lowambient kit; eturn air smoke detector B Belt Drive (5 Tons single speed models only) V TwoSpeed Belt Drive V Lowambient kit; eturn air smoke detector D Direct Drive (5 Tons single speed models only) (65 Tons only) Lowambient kit; Supply air smoke detector H High Static (5 Tons singlespeed Belt High Static (65 Tons Y Lowambient kit; eturn & Supply Drive models only) twospeed Belt Drive air smoke detectors models only) Z eturn & Supply air smoke detectors FactoryInstalled Options A Ultra LowLeak Downflow Economizer Ultra LowLeak Downflow Economizer; B DDBAnet protocol DDBAnet protocol; F Ultra LowLeak Downflow Economizer; Disconnect Switch (nonfused) FactoryInstalled Options DDBAnet protocol V LowLeak Downflow Economizer X Standard Aluminized Heat Exchanger H Disconnect Switch (nonfused) LowLeak Downflow Economizer S StainlessSteel Heat Exchanger J Ultra LowLeak Downflow Economizer; Disconnect Switch (nonfused) D Hinged Panels Disconnect Switch (nonfused) X No Options K StainlessSteel Heat Exchanger; M Disconnect Switch (nonfused); DDBAnet protocol Hinged Panels B Phase Monitor Note: Not all options available for all products. J Stainless Steel Heat Exchanger; Phase Monitor X= No Options in character th M Hinged Panel; Phase Monitor L StainlessSteel Heat Exchanger; Hinged Panels; Phase Monitor SSDT

3 Nomenclature FactoryInstalled Options StainlessSteel Heat Exchanger (as units only): A tubular heat exchanger made of 09type stainless steel is installed in the unit. LowAmbient Kit: Allows for cooling operation at lower outdoor temperatures. On the to 6ton units, cooling operation is extended from 60 F ambient temperature to 5 F outside air temperature. On 7½ 0 ton units, cooling operation is extended from 5 F ambient temperature to 0 F outside air temperature. For 5 ton units, cooling operation is extended from F ambient temperature to 0 F outside air temperature. Economizers (Downflow): Based on air conditions, can provide outside air to cool the space. Electric Heat Kits (A and heat pump units only): Available in all voltage options. Nonpowered onvenience Outlet: A 0V, 5A, FI outlet makes it easier for technicians to service the unit once an electrician runs power to the outlet. Powered onvenience Outlet: A 0V, 5A, FI outlet powered with a transformer built into the unit. hen a factoryinstalled powered convenience outlet is installed in the equipment, the unit MA (Min. ircuit Ampacity) will increase by 7.A/6.5A for 08/0V units, increase by.a for 60V units, and by.6a for 575V units. The MOP (Max. Overcurrent Protection) device must be sized accordingly. Disconnect Switch (nonfused; phase units only): A disconnect switch is installed in the unit and factory wiring will be complete from the switch to the unit. Please note that for air conditioning (DS units) and heat pump models (DSH units), the appropriate electric heat kit must be ordered to be factoryinstalled along with the disconnect switch (nonfused) when it is ordered. Please note that for models with a powered convenience outlet option and a disconnect switch (nonfused) option, the power to the powered convenience outlet will be shut off when the disconnect switch (nonfused) is in the off position. eturn Air and/or Supply Air Smoke Detectors: eturn air and/or supply air smoke detectors are installed in the unit. Hinged Access Panels: Allows access to unit s major components. ombined with latches for easy access to control box, compressor, filters and blower motor. Available on all units. Twospeed indoor fan blower models are available on 6, 7½, 8½, 0, ½, 5, 0 & 5 ton units. Section b of ASHAE Standard and Section a of ASHAE Standard 90.0 require a minimum of two fan speeds. Section 0.(m) of alifornia Energy ommission Title 0 contains a similar provision. hen the units with the twospeed indoor fan blowers operate on a call for the first stage of cooling, the fan operates at low speed, which is 66% of full speed. hen the units operate on a call for the second stage of cooling, the fan operates at full speed. In heating operation, the fan operates at full speed. During ventilation operation, the fan operates at low speed. Phase Monitor: Phase monitor ( phase only), available for 5 ton DS, D and DT series models. Phase monitor shall provide protection for motors and compressors against problems caused by phase loss, phase reversal and phase unbalance. Phase monitor is equipped with an LED that provides an ON or FAULT indicator. DD ontroller: DD communicating controller, available for 5 ton DS, D and DT series models with onboard BAnet communication interface. SSDT

4 Product Specifications DT06 05D***A* DT06 090D***A* DT08 090D***A* DT08 5D***A* DT D***A* DT060 0D***A* ooling apacity Total BTU/h 5,600 5,600 5,500 5,500 59,000 59,000 Sensible BTU/h 8,000 8,000 5,000 5,000 0,000 0,000 SEE / EE 5.5 / /.0 5.0/.0 5.0/.0 5.0/.0 5.0/.0 Decibels AI eference #s Heating apacity High Input / Output (kbtu/h) 6 / 7 9 / 75 9 / 75 5 / 9 9 / 75 8 / Low Input / Output (kbtu/h) NA 69 / / / / 56 0 / 8 Annual Fuel Utilization Efficiency (%) Temperature ise ange ( F) / / / / / 555 No. of Burners 5 6 Evaporator Motor / oil Motor Type Direct Direct Direct Direct Direct Direct heel Dia. X idth 0 X 9 0 X 9 X 0 X 0 X 0 X 0 Indoor Nominal FM,00,00,600,600,000,000 Motor Speed Tap (ooling) T T T T T T Motor Speed Tap (Heating) T T5 T5 T5 T5 T5 Horsepower / / Piston Size (ooling) Filter Size (") X 0 X () X 0 X () X 0 X () X 0 X () 6 X 0 X () 6 X 0 X () Drain Size (NPT) / / / / / / 0A efrigerant harge (oz.) Evaporator oil Face Area (ft²) ows Deep/ Fins per Inch / 6 / 6 / 6 / 6 / 6 / 6 ondenser Fan / oil Quantity of ondenser Fan Motors Horsepower PM /090 /090 /090 /090 /090 /090 Fan Diameter/ # Fan Blades / / / / / / Outdoor Nominal FM,800,800,800,800,00,00 Face Area (ft²) ows Deep/ Fins per Inch / 7 / 7 / 7 / 7 / 7 / 7 ompressor Quantity / Type (Single Stage) / Scroll / Single / Scroll / Single / Scroll / Single / Scroll / Single / Scroll / Single / Scroll / Single ompressor LA / LA. / / / / / /.0 Electrical Data VoltagePhaseFrequency 08/060 08/060 08/060 08/060 08/060 08/060 Indoor Blower HP / FLA / /.9 / /.9 / 6.9 / 6.9 / 6.9 / 6.9 Max External Static (In...) Outdoor Fan HP / FLA /. /. /. /. /.0 /.0 Total Unit Amps Min. ircuit Ampacity¹.9 /.9.9 /.9. /.. /. 0. / / 0. Max. Overcurrent Protection (amps)² 5 / 5 5 / 5 50 / / / / 60 Power Supply onduit Hole /8" /8" /8" /8" /8" /8" LowVoltage onduit Hole /" /" /" /" /" /" Operating eight (lbs) Ship eight (lbs) ¹ ire size should be determined in accordance with National Electrical odes. Extensive wire runs will require larger wire sizes. ² May use fuses or HAtype circuit breakers of the same size as noted. Note: Always check the S& plate for electrical data on the unit being installed. SSDT

5 Product Specifications DT06 05D***A* DT06 090D***A* DT08 090D***A* DT08 5D***A* DT D***A* DT060 0D***A* ooling apacity Total BTU/h 6,000 6,000 7,000 7,000 60,000 60,000 Sensible BTU/h 5,70 5,70,605,605,900,900 SEE / EE 5.0/.0 5.0/.0 5.0/.5 5.0/.5 5.0/.5 5.0/.5 Decibels AI eference #s Heating apacity High Input / Output (kbtu/h) 6 / 7 9 / 7 9 / 7 5 / 9 9 / 7 8 / 0 Low Input / Output (kbtu/h) NA 69 / / / / 55 0 / 8 Annual Fuel Utilization Efficiency (%) Temperature ise ange ( F) / / / / / 555 No. of Burners 5 6 Evaporator Motor / oil Motor Type Direct Direct Direct Direct Direct Direct heel Dia. X idth 0 X 9 0 X 9 X 0 X 0 X 0 X 0 Indoor Nominal FM,00,00,600,600,000,000 Motor Speed Tap (ooling) T T T T T T Motor Speed Tap (Heating) T T5 T5 T5 T5 T5 Horsepower Piston Size (ooling) Filter Size (") X 0 X () X 0 X () X 0 X () X 0 X () 6 X 0 X () 6 X 0 X () Drain Size (NPT) / / / / / / 0A efrigerant harge (oz.) Evaporator oil Face Area (ft²) ows Deep/ Fins per Inch / 6 / 6 / 6 / 6 / 6 / 6 ondenser Fan / oil Quantity of ondenser Fan Motors Horsepower PM /090 /090 /090 /090 /090 /090 Fan Diameter/ # Fan Blades / / / / / / Outdoor Nominal FM,800,800,800,800,00,00 Face Area (ft²) ows Deep/ Fins per Inch / 7 / 7 / 7 / 7 / 7 / 7 ompressor Quantity / Type (Single Stage) / Scroll / Single / Scroll / Single / Scroll / Single / Scroll / Single / Scroll / Single / Scroll / Single ompressor LA / LA 9.0/7 9.0/7./8./8 5.9/0 5.9/0 Electrical Data VoltagePhaseFrequency 08/060 08/060 08/060 08/060 08/060 08/060 Indoor Blower HP / FLA / /.9 / /.9 / 6.9 / 6.9 / 6.9 / 6.9 Max External Static (In...) Outdoor Fan HP / FLA ¼ /. ¼ /. ¼ /. ¼ /. / /.0 / /.0 Total Unit Amps Min. ircuit Ampacity¹ 6.5 / / /.7.7 / / / 8.8 Max. Overcurrent Protection (amps)² 5 / 5 5 / 5 5 / 5 5 / 5 0 / 0 0 / 0 Power Supply onduit Hole.5".5".5".5".5".5" LowVoltage onduit Hole ½" ½" ½" ½" ½" ½" Operating eight (lbs) Ship eight (lbs) ¹ ire size should be determined in accordance with National Electrical odes. Extensive wire runs will require larger wire sizes. ² May use fuses or HAtype circuit breakers of the same size as noted. Note: Always check the S& plate for electrical data on the unit being installed. SSDT 5

6 Expanded ooling Data Tons (Phase Models) Outdoor Ambient Temperature Entering Indoor et Bulb Temperature IDB Airflow MBh S/T T k HI P LO P MBh S/T T k HI P LO P MBh S/T T k HI P LO P MBh S/T T k HI P LO P MBh S/T T k HI P LO P MBh S/T T k HI P LO P IDB = Entering Indoor Dry Bulb Temperature Shaded area reflects AA (TVA) conditions k = Total system power High & low pressures are measured at the liquid & suction service ports. Amps: Unit amps (comp. evaporator condenser fan motors) Design Subcooling, ± the liquid access fitting connection AHI 95 test conditions. Design Superheat 8± the compressor suction access fitting connection. 6 SSDT

7 Expanded ooling Data Tons (Phase Models) (cont.) Outdoor Ambient Temperature Entering Indoor et Bulb Temperature IDB Airflow MBh S/T T k HI P LO P MBh S/T T k HI P LO P MBh S/T T k HI P LO P MBh S/T T k HI P LO P MBh S/T T k HI P LO P MBh S/T T k HI P LO P IDB = Entering Indoor Dry Bulb Temperature Shaded area reflects AHI conditions k = Total system power High & low pressures are measured at the liquid & suction service ports. Amps: Unit amps (comp. evaporator condenser fan motors) Design Subcooling, ± the liquid access fitting connection AHI 95 test conditions. Design Superheat 8± the compressor suction access fitting connection. SSDT 7

8 Expanded ooling Data Tons (Phase Models) Outdoor Ambient Temperature Entering Indoor et Bulb Temperature IDB Airflow MBh S/T T k HI P LO P MBh S/T T k HI P LO P MBh S/T T k HI P LO P MBh S/T T k HI P LO P MBh S/T T k HI P LO P MBh S/T T k HI P LO P IDB = Entering Indoor Dry Bulb Temperature Shaded area reflects AA (TVA) conditions k = Total system power High & low pressures are measured at the liquid & suction service ports. Amps: Unit amps (comp. evaporator condenser fan motors) Design Subcooling, ± the liquid access fitting connection AHI 95 test conditions. Design Superheat 8± the compressor suction access fitting connection. 8 SSDT

9 Expanded ooling Data Tons (Phase Models) (cont.) Outdoor Ambient Temperature Entering Indoor et Bulb Temperature IDB Airflow MBh S/T T k HI P LO P MBh S/T T k HI P LO P MBh S/T T k HI P LO P MBh S/T T k HI P LO P MBh S/T T k HI P LO P MBh S/T T k HI P LO P IDB = Entering Indoor Dry Bulb Temperature Shaded area reflects AHI conditions k = Total system power High & low pressures are measured at the liquid & suction service ports. Amps: Unit amps (comp. evaporator condenser fan motors) Design Subcooling, ± the liquid access fitting connection AHI 95 test conditions. Design Superheat 8± the compressor suction access fitting connection. SSDT 9

10 Expanded ooling Data 5 Tons (Phase Models) Outdoor Ambient Temperature Entering Indoor et Bulb Temperature IDB Airflow MBh S/T T k HI P LO P MBh S/T T k HI P LO P MBh S/T T k HI P LO P MBh S/T T k HI P LO P MBh S/T T k HI P LO P MBh S/T T k HI P LO P IDB = Entering Indoor Dry Bulb Temperature Shaded area reflects AA (TVA) conditions k = Total system power High & low pressures are measured at the liquid & suction service ports. Amps: Unit amps (comp. evaporator condenser fan motors) Design Subcooling, ± the liquid access fitting connection AHI 95 test conditions. Design Superheat 8± the compressor suction access fitting connection. 0 SSDT

11 Expanded ooling Data 5 Tons (Phase Models) (cont.) xxx Outdoor Ambient Temperature Entering Indoor et Bulb Temperature IDB Airflow MBh S/T T k HI P LO P MBh S/T T k HI P LO P MBh S/T T k HI P LO P MBh S/T T k HI P LO P MBh S/T T k HI P LO P MBh S/T T k HI P LO P IDB = Entering Indoor Dry Bulb Temperature Shaded area reflects AHI conditions k = Total system power High & low pressures are measured at the liquid & suction service ports. Amps: Unit amps (comp. evaporator condenser fan motors) Design Subcooling, ± the liquid access fitting connection AHI 95 test conditions. Design Superheat 8± the compressor suction access fitting connection. SSDT

12 Expanded ooling Data Tons (Phase Models) Outdoor Ambient Temperature Entering Indoor et Bulb Temperature IDB Airflow MBh S/T Delta T K AM HI P LO P MBh S/T Delta T K AM HI P LO P MBh S/T Delta T K AM HI P LO P MBh S/T Delta T K AM HI P LO P MBh S/T Delta T K AM HI P LO P MBh S/T Delta T K AM HI P LO P IDB = Entering Indoor Dry Bulb Temperature Shaded area reflects AA (TVA) conditions k = Total system power High & low pressures are measured at the liquid & suction service ports. Amps: Unit amps (comp. evaporator condenser fan motors) Design Subcooling, ± the liquid access fitting connection AHI 95 test conditions. Design Superheat 8± the compressor suction access fitting connection. SSDT

13 Expanded ooling Data Tons (Phase Models) (cont.) Outdoor Ambient Temperature Entering Indoor et Bulb Temperature IDB Airflow MBh S/T Delta T K AM HI P LO P MBh S/T Delta T K AM HI P LO P MBh S/T Delta T K AM HI P LO P MBh S/T Delta T K AM HI P LO P MBh S/T Delta T K AM HI P LO P MBh S/T Delta T K AM HI P LO P IDB = Entering Indoor Dry Bulb Temperature Shaded area reflects AHI conditions k = Total system power High & low pressures are measured at the liquid & suction service ports. Amps: Unit amps (comp. evaporator condenser fan motors) Design Subcooling, ± the liquid access fitting connection AHI 95 test conditions. Design Superheat 8± the compressor suction access fitting connection. SSDT

14 Expanded ooling Data Tons (Phase Models) Outdoor Ambient Temperature Entering Indoor et Bulb Temperature IDB Airflow MBh S/T Delta T K AM HI P LO P MBh S/T Delta T K AM HI P LO P MBh S/T Delta T K AM HI P LO P MBh S/T Delta T K AM HI P LO P MBh S/T Delta T K AM HI P LO P MBh S/T Delta T K AM HI P LO P IDB = Entering Indoor Dry Bulb Temperature Shaded area reflects AA (TVA) conditions k = Total system power High & low pressures are measured at the liquid & suction service ports. Amps: Unit amps (comp. evaporator condenser fan motors) Design Subcooling, ± the liquid access fitting connection AHI 95 test conditions. Design Superheat 8± the compressor suction access fitting connection. SSDT

15 Expanded ooling Data Tons (Phase Models) (cont.) Outdoor Ambient Temperature Entering Indoor et Bulb Temperature IDB Airflow MBh S/T Delta T K AM HI P LO P MBh S/T Delta T K AM HI P LO P MBh S/T Delta T K AM HI P LO P MBh S/T Delta T K AM HI P LO P MBh S/T Delta T K AM HI P LO P MBh S/T Delta T K AM HI P LO P IDB = Entering Indoor Dry Bulb Temperature Shaded area reflects AHI conditions k = Total system power High & low pressures are measured at the liquid & suction service ports. Amps: Unit amps (comp. evaporator condenser fan motors) Design Subcooling, ± the liquid access fitting connection AHI 95 test conditions. Design Superheat 8± the compressor suction access fitting connection. SSDT 5

16 Expanded ooling Data 5 Tons (Phase Models) Outdoor Ambient Temperature Entering Indoor et Bulb Temperature IDB Airflow MBh S/T Delta T K AM HI P LO P MBh S/T Delta T K AM HI P LO P MBh S/T Delta T K AM HI P LO P MBh S/T Delta T K AM HI P LO P MBh S/T Delta T K AM HI P LO P MBh S/T Delta T K AM HI P LO P IDB = Entering Indoor Dry Bulb Temperature Shaded area reflects AA (TVA) conditions k = Total system power High & low pressures are measured at the liquid & suction service ports. Amps: Unit amps (comp. evaporator condenser fan motors) Design Subcooling, ± the liquid access fitting connection AHI 95 test conditions. Design Superheat 8± the compressor suction access fitting connection. 6 SSDT

17 Expanded ooling Data 5 Tons (Phase Models) (cont.) Outdoor Ambient Temperature Entering Indoor et Bulb Temperature IDB Airflow MBh S/T Delta T K AM HI P LO P MBh S/T Delta T K AM HI P LO P MBh S/T Delta T K AM HI P LO P MBh S/T Delta T K AM HI P LO P MBh S/T Delta T K AM HI P LO P MBh S/T Delta T K AM HI P LO P IDB = Entering Indoor Dry Bulb Temperature Shaded area reflects AHI conditions k = Total system power High & low pressures are measured at the liquid & suction service ports. Amps: Unit amps (comp. evaporator condenser fan motors) Design Subcooling, ± the liquid access fitting connection AHI 95 test conditions. Design Superheat 8± the compressor suction access fitting connection. SSDT 7

18 Airflow Data Tons Downshot Horizontal SPEED TAP T T T T5 ESP in w.c. FM Amps atts PM SPEED TAP ESP in w.c. FM Amps atts PM T T T T Notes: Table represent dry coil without filter, to compensate for filter add 0.08" to measured E.S.P.. SFM correction for wet coil = %. Models are shipped from the factory with speed tap set on T. 8 SSDT

19 Airflow Data Tons Downshot Horizontal SPEED TAP T T T T5 ESP in w.c. FM Amps atts PM SPEED TAP ESP in w.c. FM Amps atts PM T T T T Notes: Table represent dry coil without filter, to compensate for filter add 0.08" to measured E.S.P.. SFM correction for wet coil = %. Models are shipped from the factory with speed tap set on T. SSDT 9

20 Airflow Data 5 Tons Downshot Horizontal SPEED TAP T T T T5 ESP in w.c. FM Amps atts PM SPEED TAP ESP in w.c. FM Amps atts PM T T T T Notes: Table represent dry coil without filter, to compensate for filter add 0.08" to measured E.S.P.. SFM correction for wet coil = %. Models are shipped from the factory with speed tap set on T. Airflow Pressure Drop of Downflow Economizer for to 6 Ton ooftop Units (00% eturn Air) SFM in SSDT

21 rankcase Heater, High Efficiency MEV Air Filter Option High Efficiency MEV Air Filter Option 0.50 Flanders Pre Pleat M Air Velocity vs esistance (Test Size: " x " x " High apacity) " Deep esistance (in. w.g.) Air Velocity (FPM) Tonnage: Filter Nominal Size: Part Number: Order QTY: x x 060L000 x 0 x 060L x 0 x 060L0005 rankcase Heater Selection Table ompressor Voltage rankcase ZP/Z ompressor Diameter 0V 60V 575V Heater atts 6 5.5" S 06000S 06000S /7." 00L0007S 00L0008S 00L0009S L0000S 00L000S 00L000S 90 D*,DT* & DS* Tonnage ompressor Voltage 0V 60V 575V rankcase Heater atts Ton S 06000S 06000S 0 Ton5 Ton 00L0007S 00L0008S 00L0009S 70 *Includes,&H models. SSDT

22 Electrical Data Tons Model Number Electrical ating ompressor ircuit ompressor ircuit Outdoor Fan Motor Indoor Fan Motor Optional Powered onvienience Outlet Power Supply LA LA LA LA QTY HP FLA Type HP FLA FLA MA MOP DT06***D 08/ DT06***D 08/ Standard.9 /.9 5 / 5 Direct Drive / / 9. 0 / 0 Standard 6.5 / / 5 Direct Drive / /.0 0 / 0 Tons Model Number Electrical ating ompressor ircuit ompressor ircuit Outdoor Fan Motor Indoor Fan Motor Optional Powered onvienience Outlet Power Supply LA LA LA LA QTY HP FLA Type HP FLA FLA MA MOP DT08XXXD 08/ DT08XXXD 08/ Standard. /. 50 / 50 Direct Drive / / / 50 Standard.7 /.7 5 / 5 Direct Drive / /. 5 / 0 5 Tons Model Number Electrical ating ompressor ircuit ompressor ircuit Outdoor Fan Motor Indoor Fan Motor Optional Powered onvienience Outlet Power Supply LA LA LA LA QTY HP FLA Type HP FLA FLA MA MOP DT060XXXD 08/ DT060XXXD 08/ Standard 0. / / 60 Direct Drive / / / 70 Standard 8.8 / / 0 Direct Drive / / / 50 SSDT

23 Dimensions TOP VIE FLUE/VENT OUTLET OMBUSTION AI INLET (AS UNITS) AS LINE ENTANE 7.95 FONT VIE ALL DIMENSIONS IVEN AE IN INHES ALL DIMENSIONS AND SPEIFIATIONS AE SUBJET TO HANE ITHOUT NOTIE SUPPLY AI DUT DT*06060*** THU 5TON OMMEIAL ONDENSATE DAIN OUTLET LIFTIN SHAKLE HOLES BOTH SIDES AND ENDS 8.96 FK HOLES BOTH SIDES AND BOTH ENDS 0.85 IHT END VIE ETUN AI DUT SSDT

24 Dimensions (cont.) 8. SUPPLY AI DUT ONDENSATE DAIN BOTTOM EXIT ETUN AI DUT 7.06 BASE PAN VIE (VIEED FOM TOP) MODEL TONNAES "A" "B" "" TON OMMEIAL AS, HT MP, AI ONDITIONE TON OMMEIAL AS, HT MP, AI ONDITIONE TON OMMEIAL AS, HT MP, AI ONDITIONE DISONNET LOATION LINE IE ENTANE "A" "" "B" TSTAT IE ENTANE LEFT END VIE SSDT

25 Unit learances Maintain an adequate clearance around the unit for safety, service, maintenance, and proper unit operation. Leave a clearance of 8" on all sides of the unit for possible compressor removal or service access, and to ensure proper ventilation and condenser airflow. Do not install the unit Beneath any obstruction. Install the unit away from all building exhausts to inhibit ingestion of exhaust air into the unit s freshair intake. 8" 8" 8" 8" Electrical Entrance Locations HighVoltage Entrance (emove Plug) ⅜ 0¼ LowVoltage Entrance LowVoltage Entrance ½ Dia. Power Thru the urb 7½ 7½ SSDT 5

26 oof urb Installation igging Provisions for forks have been included in the unit base frame. No other fork locations are approved. Unit must be lifted by the four lifting holes located at the base frame corners. Lifting cables should be attached to the unit with shackles. The distance between the crane hook and the top of the unit must not be less than 60. Two spreader bars must span over the unit to prevent damage to the cabinet by the lift cables. Spreader bars must be of sufficient length so that cables do not come in contact with the unit during transport. emove wood struts mounted beneath unit base frame before setting unit on roof curb. These struts are intended to protect unit base frame from fork lift damage. To remove the struts, extract the sheet metal retainers and pull the struts through the base of the unit. efer to rigging label on the unit. Important: If using bottom discharge with roof curb, ductwork should be attached to the curb prior to installing the unit. Ductwork dimensions are shown in oof urb Installation Instructions Manual. efer to the oof urb Installation Instructions for proper curb installation. urbing must be installed in compliance with the National oofing ontractors Association Manual. Lower unit carefully onto roof mounting curb. hile rigging the unit, the center of gravity will cause the condenser end to be lower than the supply air end. Bring condenser end of unit into alignment with the curb. ith condenser end of the unit resting on curb member and using curb as a fulcrum, lower opposite end of the unit until entire unit is seated on the curb. hen a rectangular cantilever curb is used, take care to center the unit. heck for proper alignment and orientation of supply and return openings with duct. To assist in determining rigging requirements, unit weights are shown below. orner & enterofravity Locations Y A ondenser oil ONDENSE OIL ETUN eturn EVAPAT Evaporator oil OIL Model X (In) Y (In) Shipping eight (Lbs) Operating eight (Lbs) orner eights (Lbs.) A B D DT0605*DXXX DT06090*DXXX SUPPLY Supply DT08090*DXXX DT085*DXXX DT060090*DXXX B OMPESS ompressor D DT0600*DXXX X urb installations must comply with local codes and should follow the established guidelines of the National oofing ontractors Association. Proper unit installation requires that the roof curb be firmly and permanently attached to the roof structure. heck for adequate fastening method prior to setting the unit on the curb. Full perimeter roof curbs are available from the factory and are shipped unassembled. The installing contractor is responsible for field assembly, squaring, leveling, and mounting on the roof structure. All required hardware necessary for the assembly of the sheet metal curb is included in the curb accessory package. Determine sufficient structural support before locating and mounting the curb and package unit. Ductwork must be constructed using industry guidelines. The ductwork must be placed into the roof curb before mounting the package unit. Our full perimeter curbs include duct connection frames to be assembled with the curb. antileveredtype curbs are not available from the factory. ontractor furnishes curb insulation, cant strips, flashing, and general roofing material. Support curbs on parallel sides with roof members. To prevent damage to the unit, the roof members cannot penetrate supply and return duct openings. Note: The unit and curb accessories are designed to allow Down Shot duct installation before unit placement. Duct installation after unit placement is not recommended. See the manual shipped with the roof curb for assembly and installation instructions. 6 SSDT