DCC Commercial. 15- & 20-Ton, Three-Phase. 15 Tons Cooling Capacity: 180,000 BTU/h 20 Tons Cooling Capacity: 240,000 BTU/h. Packaged Air Conditioners

Transcription

1 D ommercial Standard Features R-410A chlorine- free refrigerant High-efficiency scroll compressor opper tube / aluminum fin coils High- and low-pressure switches High-capacity, steel-cased filter drier Built-in filter rack with standard 2 filters (convertible to 4 filters) Heater kits with single-point entry rankcase heaters Power block for field wiring 24-volt terminal strip Easy to service Bottom utility entry AHRI ertified; ETL Listed abinet Features Heavy-gauge, galvanized-steel cabinet with UV-resistant powder-paint finish Full perimeter rail Sloped drain pan 15- & 20-Ton, Three-Phase Packaged Air onditioners 15 Tons ooling apacity: 180,000 BTU/h 20 Tons ooling apacity: 240,000 BTU/h ontents Nomenclature... 2 Product Specifications... 3 Expanded ooling Data... 5 Airflow Data... 9 Heating Kit Data Dimensions Wiring Diagrams Accessories * omplete warranty details available from your local dealer or at SS-D15 7/13

2 Nomenclature D B * * * A * ,5,6 7,8, Revision Levels Major & Minor Brand Factory-Installed Options D Daikin X No Options A Non-powered convenience outlet onfiguration B Powered convenience outlet ommercial Low-ambient kit D Return air smoke detector Application E Supply air smoke detector ooling F Non-powered convenience outlet; G Gas Heat Low-ambient kit H Heat Pump G Non-powered convenience outlet; Return air smoke detector Nominal ooling apacity H Non-powered convenience outlet; Tons 102 8½ Tons Supply air smoke detector Tons Tons J Non-powered convenience outlet; Tons ½ tons Return & Supply air smoke detectors Tons Tons K Non-powered convenience outlet; 090 7½ Tons Tons Low-ambient kit; Supply air smoke detector L Non-powered convenience outlet; Nominal Heating apacity Low-ambient kit Gas/Electric A/ HP (Factory-Installed Electric Heat) Return & Supply air smoke detectors ,000 BTU/h XXX No Heat M Powered convenience outlet; ,000 BTU/h kw kw Low-ambient kit ,000 BTU/h kw kw N Powered convenience outlet; ,000 BTU/h kw kw Return air smoke detector ,000 BTU/h kw kw O Powered convenience outlet; ,000 BTU/h kw kw Return & Supply air smoke detectors ,000 BTU/h kw P Powered convenience outlet; See product specifications for heat size(s) available for each capacity. Supply air smoke detector Q Powered convenience outlet; Low- Voltage ambient kit; Return air smoke detector /1/ /3/60 R Powered convenience outlet; Low /3/ /3/60 ambient kit; Supply air smoke detector T Powered convenience outlet; Supply Fan/Drive Type/Motor Low-ambient kit; Return & Supply B Belt Drive air smoke detectors D Direct Drive U Non-powered convenience outlet; Low-ambient kit; Return air smoke detector Factory-Installed Options V Low-ambient kit; Return air smoke detector X No Options W Low-ambient kit; Supply air smoke detector A Downflow Economizer Y Low-ambient kit; Return & Supply H Disconnect Switch (non-fused) air smoke detectors J Downflow Economizer; Disconnect Switch (non-fused) Z Return & Supply air smoke detectors Note: Not all options available for all products. Factory-Installed Options X Standard Aluminized Heat Exchanger S Stainless-Steel Heat Exchanger Factory-Installed Options Stainless-Steel Heat Exchanger (PG units only): A tubular heat exchanger made of 409-type stainless steel is installed in the unit. Low-Ambient Kit: Allows for cooling operation at lower outdoor temperatures. On the 3- to 6-ton units, cooling operation is extended from 60 F ambient temperature to 35 F outside air temperature. On 7½- to 20-ton units, cooling operation is extended from 35 F ambient temperature to 0 F outside air temperature. Economizers (Downflow): Based on air conditions, can provide outside air to cool the space. Electric Heat Kits (P and PH units only): Available in all voltage options. Non-powered onvenience Outlet: A 120V, 15A, GFI outlet makes it easier for technicians to service the unit once an electrician runs power to the outlet. Powered onvenience Outlet: A 120V, 15A, GFI outlet powered with a transformer built into the unit; for use when unit is not running. When a factory-installed powered convenience outlet is installed in the equipment, the unit MA (Min. ircuit Ampacity) will increase by 7.5A for 208/230V units, increase by 3.75A for 460V units, and by 3A for 575V units. The MOP (Max. Overcurrent Protection) device must be sized accordingly. Disconnect Switch (non-fused): A disconnect switch is installed in the unit and factory wiring will be complete from the switch to the unit. Please note that for air conditioning (P units) and heat pump models (PH units), the appropriate electric heat kit must be ordered to be factory-installed along with the disconnect switch (non-fused) when it is ordered. Please note that for models with a powered convenience outlet option and a disconnect switch (non-fused) option, the power to the powered convenience outlet will be shut off when the disconnect switch (non-fused) is in the off position. Return Air and/or Supply Air Smoke Detectors: Return air and/or supply air smoke detectors are installed in the unit. 2 SS-D15

3 Product Specifications 15 Tons D180*** 3B***A* D180*** 4B***A* D180*** 7B***A* ooling apacity Total, BTU/h 180, , ,000 Sensible BTU/h 134, , ,600 EER / IEER 11 / / / 11.2 Decibels ARI Reference #s Evapoartor Motor / oil Motor Type (Belt Drive) Std Static Std Static Std Static Indoor Nominal FM 6,000 6,000 6,000 Indoor Motor FLA (ooling) Horsepower - RPM 3.0-1, , ,725 Metering Device TXV TXV TXV Filter Size (#) 20 x 25 x 2 (6) 20 x 25 x 2 (6) 20 x 25 x 2 (6) Drain Size (NPT) 1" 1" 1" R-410A Refrigerant harge ir # R-410A Refrigerant harge ir # Evaporator oil Face Area (ft²) Rows Deep / Fins per Inch 4 / 16 4 / 16 4 / 16 Belt Drive Evap Fan Data # of Wheels (D x W) 2 (15" x 12") 2 (15" x 12") 2 (15" x 12") Motor Sheave 1VM50 x ⅞" 1VM50 x ⅞" 1VM50 x ⅞" Blower Sheave 100 x 1³ ₁₆" 100 x 1³ ₁₆ 100 x 1³ ₁₆ Belt BX45 BX45 BX45 ondenser Fan / oil Quantity of ondenser Fan Motors Horsepower - RPM ⅓ - 1,075 ⅓ - 1,075 ⅓ - 1,075 Fan Diameter / # Fan Blades 22 / 3 22 / 3 22 / 3 Outdoor Nominal FM 9,000 9,000 9,000 Face Area (ft²) Rows Deep / Fins per Inch 2 / 27 2 / 27 2 / 27 ompressor Quantity / Type 2 / Scroll 2 / Scroll 2 / Scroll ompressor RLA / LRA ea. 25 / / / 78 Electrical Data / Static Voltage / Phase / Frequency /3/60 460/3/60 575/3/60 Outdoor Fan FLA / LRA 2.4 / / / 2.2 Total Unit Amps Min. ircuit Ampacity¹ Max. Overcurrent Protection (amps)² Entrance Power Supply 2⅛" 2⅛" 2⅛" Entrance ontrol Voltage ⅞" ⅞" ⅞" Operating Weight (lbs) Ship Weight (lbs) ¹ Wire size should be determined in accordance with National Electrical odes. Extensive wire runs will require larger wire sizes. ² May use fuses or HAR-type circuit breakers of the same size as noted. Note: Always check the S&R plate for electrical data on the unit being installed. SS-D15 3

4 Product Specifications 20 Tons D240 ***3B***A* D240 ***4B***A* D240 ***7B***A* ooling apacity Total, BTU/h 240, , ,000 Sensible BTU/h 181, , ,000 EER / IEER 10.0 / / / 10.1 Decibels ARI Reference #s Evapoartor Motor / oil Motor Type (Belt Drive) Std Static Belt Drive Std Static Belt Drive Std Static Belt Drive Indoor Nominal FM 7,000 7,000 7,000 Indoor Motor FLA (ooling) Horsepower - RPM Metering Device TXV TXV TXV Filter Size (#) 20 x 25 x 2 (6) 20 x 25 x 2 (6) 20 x 25 x 2 (6) Drain Size (NPT) 1" 1" 1" R-410A Refrigerant harge ir #1 & #2 200 ozs. 200 ozs. 200 ozs. Evaporator oil Face Area (ft²) Rows Deep / Fins per Inch 4 / 16 4 / 16 4 / 16 Belt Drive Evap Fan Data # of Wheels (D x W) 2 (15" x 15") 2 (15" x 15") 2 (15" x 15") Motor Sheave 1VP60 x 1⅛" 1VP60 x 1⅛" 1VP60 x 1⅛" Blower Sheave 100 x 1⁷ ₁₆" 100 x 11⁷ ₁₆ 100 x 1⁷ ₁₆ Belt BX46 BX46 BX46 ondenser Fan / oil Quantity of ondenser Fan Motors Horsepower - RPM ⅓ - 1,075 ⅓ - 1,075 ⅓ - 1,075 Fan Diameter / # Fan Blades 22 / 3 22 / 3 22 / 3 Outdoor Nominal FM 7,200 7,200 7,200 Face Area (ft²) Rows Deep / Fins per Inch 2 / 27 2 / 27 2 / 27 ompressor Quantity / Type 2 / Scroll 2 / Scroll 2 / Scroll ompressor RLA / LRA ea / / / 80 Electrical Data / Static Voltage / Phase / Frequency /3/60 460/3/60 575/3/60 Outdoor Fan FLA / LRA 2.4 / / / 2.2 Total Unit Amps Min. ircuit Ampacity¹ Max. Overcurrent Protection (amps)² Entrance Power Supply 2⅛" 2⅛" 2⅛" Entrance ontrol Voltage ⅞" ⅞" ⅞" Operating Weight (lbs) Ship Weight (lbs) ¹ Wire size should be determined in accordance with National Electrical odes. Extensive wire runs will require larger wire sizes. ² May use fuses or HAR-type circuit breakers of the same size as noted. Note: Always check the S&R plate for electrical data on the unit being installed. 4 SS-D15

5 Expanded ooling Data 15 Tons Outdoor Ambient Temperature Entering Indoor Wet Bulb Temperature IDB Airflow MBh S/T T HI PR LO PR MBh S/T T HI PR LO PR MBh S/T T HI PR LO PR MBh S/T T HI PR LO PR MBh S/T T HI PR LO PR MBh S/T T HI PR LO PR IDB: Entering Indoor Dry Bulb Temperature Shaded area reflects AA (TVA) conditions High and low pressures are measured at the liquid and suction access fittings. SS-D15 5

6 Expanded ooling Data 15 Tons (cont.) Outdoor Ambient Temperature Entering Indoor Wet Bulb Temperature IDB Airflow MBh S/T T HI PR LO PR MBh S/T T HI PR LO PR MBh S/T T HI PR LO PR MBh S/T T HI PR LO PR MBh S/T T HI PR LO PR MBh S/T T HI PR LO PR IDB: Entering Indoor Dry Bulb Temperature Shaded area reflects AHRI (TVA) conditions High and low pressures are measured at the liquid and suction access fittings. 6 SS-D15

7 Expanded ooling Data 20 Tons Outdoor Ambient Temperature Entering Indoor Wet Bulb Temperature IDB Airflow MBh S/T T HI PR LO PR MBh S/T T HI PR LO PR MBh S/T T HI PR LO PR MBh S/T T HI PR LO PR MBh S/T T HI PR LO PR MBh S/T T HI PR LO PR IDB: Entering Indoor Dry Bulb Temperature Shaded area reflects AA (TVA) conditions High and low pressures are measured at the liquid and suction access fittings. SS-D15 7

8 Expanded ooling Data 20 Tons (cont.) Outdoor Ambient Temperature Entering Indoor Wet Bulb Temperature IDB Airflow MBh S/T T HI PR LO PR MBh S/T T HI PR LO PR MBh S/T T HI PR LO PR MBh S/T T HI PR LO PR MBh S/T T HI PR LO PR MBh S/T T HI PR LO PR IDB: Entering Indoor Dry Bulb Temperature Shaded area reflects AHRI (TVA) conditions High and low pressures are measured at the liquid and suction access fittings. 8 SS-D15

9 Airflow Data 15 Tons ESP (" H₂O) Standard Belt Drive Down Shot Turns Open FM BHP FM BHP FM BHP FM BHP FM BHP FM BHP FM BHP High-Static Belt Drive Down Shot Turns Open ESP (" H₂O) FM BHP FM BHP FM BHP FM BHP FM BHP FM BHP FM BHP Notes Airflow table represent dry coil with filters installed; SFM correction factor for wet coil is 4%. Any adjustment made to the blower should not cause the motor to draw more than the motor rated RLA. Application that exceed the above could require a larger motor. Minimum rated SFM is 350 per ton. High-static airflow requires installation of a high-static kit (HSKT180). Unit factory shipped with the sheave set at 2.5 turns open. SS-D15 9

10 Airflow Data 20 Tons ESP (" H₂O) Standard Belt Drive Down Shot Turns Open FM BHP FM BHP FM BHP FM BHP FM BHP FM BHP FM BHP High-Static Belt Drive Down Shot Turns Open ESP (" H₂O) FM BHP FM BHP FM BHP FM BHP FM BHP FM BHP FM BHP Notes Airflow table represent dry coil with filters installed; SFM correction factor for wet coil is 4%. Any adjustment made to the blower should not cause the motor to draw more than the motor rated RLA. Application that exceed the above could require a larger motor. Minimum rated SFM is 350 per ton. High-static airflow requires installation of high kit (HSKT240) or factory-built high-static model. Unit factory shipped with the sheave set at 2.5 turns open SS-D15

11 Heat Kit Electrical Data (Blower Only, Heat Mode) 15 Tons Three-Phase 208 / 240V Model MA¹ MOP² Actual 240V Recommended Airflow Range D180***3B EHK FM EHK FM EHK FM 480-Volt 480V Model MA¹ MOP² Actual 480V Recommended Airflow Range D180***4B EHK FM EHK FM EHK FM 575-Volt 575V Model MA¹ MOP² Actual 575V Recommended Airflow Range D180***7B EHK FM EHK FM EHK FM ¹ Maximum ircuit Ampacity ² Maximum Overcurrent Protection (Amps) Note: When using electric heat kit, the single-point kit installed in the unit is needed to meet UL requirements. KW orrection Factors kw orrection Factor Supply Voltage orrection Factor kw orrection Factor (for 480V Units) kw orrection Factor (for 575V Units) Supply Voltage Supply Voltage orrection Factor orrection Factor For other voltage, use voltage² / 480² Multiply rated kw by correction factor to get actual kw. SS-D

12 Heat Kit Electrical Data (Blower Only, Heat Mode) 20 Tons Three-Phase 208 / 240V Model & Heat Kit Usage MA¹ MOP² Actual 240V Recommended Airflow Range D240***3B EHK FM EHK FM EHK FM EHK FM 480-Volt 480V Model MA¹ MOP² Actual 480V Recommended Airflow Range D240***4B EHK FM EHK FM EHK FM EHK FM 575-Volt 575V Model MA¹ MOP² Actual 575V Recommended Airflow Range D240***7B EHK FM EHK FM EHK FM EHK FM ¹ Maximum ircuit Ampacity ² Maximum Overcurrent Protection (amps) Note: When using electric heat kit, the single-point kit installed in the unit is needed to meet UL requirements. KW orrection Factors kw orrection Factor Supply Voltage orrection Factor kw orrection Factor (for 480V Units) kw orrection Factor (for 575V Units) Supply Voltage Supply Voltage orrection Factor orrection Factor For other voltage, use voltage² / 480² Multiply rated kw by correction factor to get actual kw SS-D15

13 Dimensions 133½ A 88⁷/₃₂ B 50⁹/₃₂ 5⁵/₃₂ D 2 x 21 2 x Return 22 Supply Gas Inlet Location (¾ NPT) Vertical Discharge (Top of Unit) 9⅔ 46¹ ₁₀ Flue Vent SS-D

14 Unit learances Maintain an adequate clearance around the unit for safety, service, maintenance, and proper unit operation. Leave a total clearance of 75 on the main control panel side of the unit for possible removal of fan shaft, coil, electric heat, and gas furnace. Leave a clearance of 48 on all other sides of the unit for possible compressor removal or service access, and to ensure proper ventilation and condenser airflow. Do not install the unit beneath any obstruction. Install the unit away from all building exhausts to inhibit Ingestion of exhaust air into the unit s fresh-air intake. 36 minimum roof overhang Electrical Entrance Locations 12¹/₈ 3³/₅ High-Voltage Entrance 3⁴/₅ Low- Voltage Entrance 14 SS-D15

15 EVAPAT OILS Product Specifications Roof urb Installation Rigging Provisions for forks have been included in the unit base frame. No other fork locations are approved. Unit must be lifted by the four lifting holes located at the base frame corners. Lifting cables should be attached to the unit with shackles. The distance between the crane hook and the top of the unit must not be less than 60. Two spreader bars must span over the unit to prevent damage to the cabinet by the lift cables. Spreader bars must be of sufficient length so that cables do not come in contact with the unit during transport. Remove wood struts mounted beneath unit base frame before setting unit on roof curb. These struts are intended to protect unit base frame from fork lift damage. To remove the struts, extract the sheet metal retainers and pull the struts through the base of the unit. Refer to rigging label on the unit. Important: If using bottom discharge with roof curb, duct-work should be attached to the curb prior to installing the unit. Ductwork dimensions are shown in Roof urb Installation Instructions Manual. Refer to the Roof urb Installation Instructions for proper curb installation. urbing must be installed in compliance with the National Roofing ontractors Association Manual. Lower unit carefully onto roof mounting curb. While rigging the unit, the center of gravity will cause the condenser end to be lower than the supply air end. Bring condenser end of unit into alignment with the curb. With condenser end of the unit resting on curb member and using curb as a fulcrum, lower opposite end of the unit until entire unit is seated on the curb. When a rectangular cantilever curb is used, take care to center the unit. heck for proper alignment and orientation of supply and return openings with duct. A Y 40 B OMPRESS ompressor 1 ompressor OMPRESS X G Supply Evaporator oil orner & enter-of-gravity Locations Return D 15-Ton Units Weights (lbs.) orner Weight A 590 orner Weight B 482 orner Weight 492 orner Weight D 401 Shipping Weight 2080 Operating Weight Ton Units Weights (lbs) orner Weight - A 655 orner Weight - B 535 orner Weight orner Weight - D 420 Unit Shipping Weight 2235 Unit Operating Weight 2120 To assist in determining rigging requirements, unit weights are shown to the right. Note: These weights are calculated without installed accessories. SS-D

16 Roof urb Installation urb installations must comply with local codes and should follow the established guidelines of the National Roofing ontractors Association. Proper unit installation requires that the roof curb be firmly and permanently attached to the roof structure. heck for adequate fastening method prior to setting the unit on the curb. Full perimeter roof curbs are available from the factory and are shipped unassembled. The installing contractor is responsible for field assembly, squaring, leveling, and mounting on the roof structure. All required hardware necessary for the assembly of the sheet metal curb is included in the curb accessory package. Determine sufficient structural support before locating and mounting the curb and package unit. Duct-work must be constructed using industry guidelines. The duct-work must be placed into the roof curb before mounting the package unit. Our full perimeter curbs include duct connection frames to be assembled with the curb. antilevered-type curbs are not available from the factory. ontractor furnishes curb insulation, cant strips, flashing, and general roofing material. Support curbs on parallel sides with roof members. To prevent damage to the unit, the roof members cannot penetrate supply and return duct openings. Note: The unit and curb accessories are designed to allow vertical duct installation before unit placement. Duct installation after unit placement is not recommended. See the manual shipped with the roof curb for assembly and installation instructions. 123 urb Top O.D. 119¾ urb Top O.D. 17²/₂₅ 17²/₂₅ 17²/₂₅ 74¾ urb O.D. 61⅞ 61⅞ 23⅞ 78 urb Top O.D. Insulated Panels 11¼ 1⅝ Typ. 1¾ 123 urb Bottom O.D. 1⅜ Typ. 1¾ 77½ urb Bottom O.D SS-D15

17 Wiring Diagram D 15 & 20 Tons (230V/460V/575V, Three-Phase Belt Drive PB POWER SUPPLY 208V-240V-460V-575V 3 ph / 60hZ L1 L2 GND B T1 T2 GR EM H2 T1 OMP T2 2 T3 H1 T1 OMP T2 1 T3 GR HR2 HR1 L3 L1 L2 L3 L1 L2 L3 2 1 T3 T1 T2 T3 T1 T2 T3 NOTE v 208v 460v R2 575v V GR 4 1 PK BR BR BR BR BR BR F1 F F2 F F3 F TB2 M3 High Voltage: Disconnect all power before servicing or installing this unit. Multiple power sources may be present. Failure to do so may cause property damage, personal injury, or death. HPS2 LPS2 SEE NOTE 3 PLF 2 GR WH R WH PK BR PK HPS R PLF BR GR GR PK R WH BR GR LPS1 WH GR GR BR G R XFMR-R XFMR- SPEED UP EBTDR NOTE #2 K1 K1 M1 BR BR NO OM N M2 M2 M1 GR Wiring is subject to change. Always refer to the wiring diagram or the Warning unit for the most up-to-date wiring. BR TB1 S1 S2 R G Y1 Y2 W1 W2 O WH REPLAE JUMPER WITH SMOKE/FIRE DETET TO THERMOSTAT SEE NOTE 4 BR 0140L02581-A SS-D

18 Wiring Diagram D 15 & 20 Tons (230V/460V/575V, Three-Phase Belt Drive L1 L2 L3 B OMPONENT LEGEND OWER ONTAT SUPPLY VOLTAGE /460/575/3/60 H OMPRESS ONTAT RANK ASE HEATER HR RANK ASE HEATER RELAY 1 T1 T2 T2 1 R M OMPRESS ONTAT RELAY ONDENSER MOT F1 2 T1 B T1 H1 H2 T1 OMP1 T3 F M1 T2 T1 OMP2 T3 T2 EM T3 EBTDR F3 T2 B B 3 1 T3 F2 F M2 F M3 2 T V NOTE TR 24V MR ONDENSER MOT RELAY OMP OMPRESS EON EONOMIZER EBTD ELETRONI OWER TIME DELAY EMR EVAPAT MOT RELAY R RELAY EM EVAPAT MOT F FAN APAIT GND EQUPIMENT GROUND HPS HIGH PRESSURE SWITH LPS LOW PRESSURE SWITH PB POWER DISTRUBTION OK PLF FEMALE PLUG / ONNET TB1 TERMINAL OK (24V SIGNAL) TB2 TERMINAL OK (L1) TRANSFMER TR NOTES: 1. REPLAEMENT WIRE MUST BE SAME SIZE AND TYPE INSULATION AS IGINAL (AT LEAST 105 ) USE OPPER ONDUT ONLY. 2. USE OPPER ONDUTS ONLY ++ USE N.E.. LASS 2 WIRE 3. EONOMIZER PLUG LOATED IN THE RETURN AIR OMPARTMENT, REMOVE MALE PLUG, ATTAH FEMALE PLUG TO THE EONOMIZER AESSY. 4. F TWO STAGE OPERATION REMOVE W1 TO W2 WIRE JUMPER. 5. F 208V OPERATION MOVE AK WIRE FROM TERMINAL 3 TO TERMINAL 2 ON 240V TRANSFMER Wiring is subject to change. Always refer to the wiring diagram or the Warning unit for the most up-to-date wiring. High Voltage: Disconnect all power before servicing or installing this unit. Multiple power sources may be present. Failure to do so may cause property damage, personal injury, or death. R G R PLF LPS1 HPS1 1 4 R1 EBTDR EBTDR LPS2 HPS2 3 2 B R2 PLF HR2 6 4 HR1 SEE NOTE 3 FATY WIRING LINE VOLTAGE LOW VOLTAGE OPTIONAL HIGH VOLTAGE FATY WIRING HIGH VOLATGE LOW VOLATGE WIRE ODE AK UE BR BROWN GR GREEN ANGE PK PINK RPLE RED WH WHITE THERMOSTAT ++ FIELD WIRING 2 STAGE OOLING W1 WH G GR R Y1 Y2 PK O W2 BR TB1 W1 G R Y1 Y2 O W2 STAT TB1 S1 R S2 G Y1 Y2 W1 W2 O YELLOW REPLAE JUMPER WITH SMOKE/FIRE DETET THERMOSTAT ++ WH SEE NOTE 4 /PK YELLOW WITH PINK STRIP /PK UE WITH PINK STRIP SEE UNIT RATING PLATE F TYPE AND SIZE OF OVER URRENT PROTETION 0140L02582-A 18 SS-D15

19 Accessories Filed-Installed Item # Description Fits Model Sizes Field- Installed 14RB " Roof urb tons D25FD % Manual Fresh Air Damper tons D25MFD % Motorized Fresh Air Damper tons DDNBB Burglar Bar Sleeves with Supply and Return All Models DK180 oncentric Duct Kit 15 tons DK240 oncentric Duct Kit 20 tons Factory- Installed onvenience Outlet: Powered All Models onvenience Outlet: Non Powered All Models Disconnect Switch (non-fused) All Models DDNENJ Downflow Economizer tons Electric Heat Kits (75kW not available as factory-installed kit) All Models HSKT180 High-Static Kit (230/460v) 15 tons HSKT180-7 High-Static Kit (575v) 15 tons HSKT240 High-Static Kit (230/460v) 20 tons HSKT240-7 High-Static Kit (575v) 20 tons HZURB180240ED Horizontal Discharge urb End Discharge tons HZURB180240SDN Horizontal Discharge urb Side Discharge; duct openings on non-service side tons HZURB180240SDS Horizontal Discharge urb Side Discharge; duct openings on service side tons GHR-1 Hurricane Restraint lips All Models LAKT03 Low-Ambient Kit tons DPE Power Exhaust (208/230v) tons DPE Power Exhaust (460v) tons Smoke Detector All Models SS-D

20 Notes Our continuing commitment to quality products may mean a change in specifications without notice Houston, Texas Printed in the USA SS-D15